[U-Boot] [PATCH 07/13 v4] ARM: OMAP3: Add memory and syslib common files
dirk.behme at googlemail.com
dirk.behme at googlemail.com
Fri Oct 17 21:28:24 CEST 2008
Subject: [PATCH 07/13 v4] ARM: OMAP3: Add memory and syslib common files
From: Dirk Behme <dirk.behme at gmail.com>
Add memory and syslib common files.
Signed-off-by: Dirk Behme <dirk.behme at gmail.com>
---
Changes in version v3:
- Add detection and support for 128MB/256MB RAM by Mans Rullgard
Changes in version v2:
- Move common ARM Cortex A8 code to cpu/arm_cortexa8/ and OMAP3 SoC specific common code to cpu/arm_cortexa8/omap3 as proposed by Wolfgang.
cpu/arm_cortexa8/omap3/Makefile | 2
cpu/arm_cortexa8/omap3/mem.c | 298 ++++++++++++++++++++++++++++++++++++++++
cpu/arm_cortexa8/omap3/syslib.c | 72 +++++++++
examples/Makefile | 6
4 files changed, 375 insertions(+), 3 deletions(-)
Index: u-boot-arm/cpu/arm_cortexa8/omap3/mem.c
===================================================================
--- /dev/null
+++ u-boot-arm/cpu/arm_cortexa8/omap3/mem.c
@@ -0,0 +1,298 @@
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Manikandan Pillai <mani.pillai at ti.com>
+ *
+ * Initial Code from:
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Syed Mohammed Khasim <khasim at ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <command.h>
+
+/* Only One NAND allowed on board at a time.
+ * The GPMC CS Base for the same
+ */
+unsigned int boot_flash_base;
+unsigned int boot_flash_off;
+unsigned int boot_flash_sec;
+unsigned int boot_flash_type;
+volatile unsigned int boot_flash_env_addr;
+
+/* help common/env_flash.c */
+#ifdef ENV_IS_VARIABLE
+
+uchar(*boot_env_get_char_spec) (int index);
+int (*boot_env_init) (void);
+int (*boot_saveenv) (void);
+void (*boot_env_relocate_spec) (void);
+
+/* 16 bit NAND */
+uchar env_get_char_spec(int index);
+int env_init(void);
+int saveenv(void);
+void env_relocate_spec(void);
+extern char *env_name_spec;
+
+#if defined(CONFIG_CMD_NAND)
+u8 is_nand;
+#endif
+
+#if defined(CONFIG_CMD_ONENAND)
+u8 is_onenand;
+#endif
+
+#endif /* ENV_IS_VARIABLE */
+
+#if defined(CONFIG_CMD_NAND)
+static u32 gpmc_m_nand[GPMC_MAX_REG] = {
+ M_NAND_GPMC_CONFIG1,
+ M_NAND_GPMC_CONFIG2,
+ M_NAND_GPMC_CONFIG3,
+ M_NAND_GPMC_CONFIG4,
+ M_NAND_GPMC_CONFIG5,
+ M_NAND_GPMC_CONFIG6, 0
+};
+unsigned int nand_cs_base;
+#endif
+
+#if defined(CONFIG_CMD_ONENAND)
+static u32 gpmc_onenand[GPMC_MAX_REG] = {
+ ONENAND_GPMC_CONFIG1,
+ ONENAND_GPMC_CONFIG2,
+ ONENAND_GPMC_CONFIG3,
+ ONENAND_GPMC_CONFIG4,
+ ONENAND_GPMC_CONFIG5,
+ ONENAND_GPMC_CONFIG6, 0
+};
+unsigned int onenand_cs_base;
+
+#endif
+
+/**************************************************************************
+ * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow
+ * command line mem=xyz use all memory with out discontinuous support
+ * compiled in. Could do it at the ATAG, but there really is two banks...
+ * Called as part of 2nd phase DDR init.
+ **************************************************************************/
+void make_cs1_contiguous(void)
+{
+ u32 size, a_add_low, a_add_high;
+
+ size = get_sdr_cs_size(SDRC_CS0_OSET);
+ size /= SZ_32M; /* find size to offset CS1 */
+ a_add_high = (size & 3) << 8; /* set up low field */
+ a_add_low = (size & 0x3C) >> 2; /* set up high field */
+ writel((a_add_high | a_add_low), SDRC_CS_CFG);
+
+}
+
+/********************************************************
+ * mem_ok() - test used to see if timings are correct
+ * for a part. Helps in guessing which part
+ * we are currently using.
+ *******************************************************/
+u32 mem_ok(u32 cs)
+{
+ u32 val1, val2, addr;
+ u32 pattern = 0x12345678;
+
+ addr = OMAP34XX_SDRC_CS0 + get_sdr_cs_offset(cs);
+
+ writel(0x0, addr + 0x400); /* clear pos A */
+ writel(pattern, addr); /* pattern to pos B */
+ writel(0x0, addr + 4); /* remove pattern off the bus */
+ val1 = readl(addr + 0x400); /* get pos A value */
+ val2 = readl(addr); /* get val2 */
+
+ if ((val1 != 0) || (val2 != pattern)) /* see if pos A val changed */
+ return 0;
+ else
+ return 1;
+}
+
+/********************************************************
+ * sdrc_init() - init the sdrc chip selects CS0 and CS1
+ * - early init routines, called from flash or
+ * SRAM.
+ *******************************************************/
+void sdrc_init(void)
+{
+ /* only init up first bank here */
+ do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT);
+}
+
+/*************************************************************************
+ * do_sdrc_init(): initialize the SDRAM for use.
+ * -code sets up SDRAM basic SDRC timings for CS0
+ * -optimal settings can be placed here, or redone after i2c
+ * inspection of board info
+ *
+ * - code called ones in C-Stack only context for CS0 and a possible 2nd
+ * time depending on memory configuration from stack+global context
+ **************************************************************************/
+
+void do_sdrc_init(u32 offset, u32 early)
+{
+ u32 actim_offs = offset? 0x28: 0;
+
+ if (early) {
+ /* reset sdrc controller */
+ writel(SOFTRESET, SDRC_SYSCONFIG);
+ wait_on_value(BIT0, BIT0, SDRC_STATUS, 12000000);
+ writel(0, SDRC_SYSCONFIG);
+
+ /* setup sdrc to ball mux */
+ writel(SDP_SDRC_SHARING, SDRC_SHARING);
+
+ /* Disble Power Down of CKE cuz of 1 CKE on combo part */
+ writel(0x00000081, SDRC_POWER);
+
+ writel(0x0000A, SDRC_DLLA_CTRL);
+ sdelay(0x20000);
+ }
+
+ writel(0x02584099, SDRC_MCFG_0 + offset);
+ writel(0x4e201, SDRC_RFR_CTRL + offset);
+ writel(0xaa9db4c6, SDRC_ACTIM_CTRLA_0 + actim_offs);
+ writel(0x11517, SDRC_ACTIM_CTRLB_0 + actim_offs);
+
+ writel(CMD_NOP, SDRC_MANUAL_0 + offset);
+ writel(CMD_PRECHARGE, SDRC_MANUAL_0 + offset);
+ writel(CMD_AUTOREFRESH, SDRC_MANUAL_0 + offset);
+ writel(CMD_AUTOREFRESH, SDRC_MANUAL_0 + offset);
+
+ /* CAS latency 3, Write Burst = Read Burst, Serial Mode,
+ Burst length = 4 */
+ writel(0x00000032, SDRC_MR_0 + offset);
+
+ if (!mem_ok(offset))
+ writel(0, SDRC_MCFG_0 + offset);
+}
+
+void enable_gpmc_config(u32 *gpmc_config, u32 gpmc_base, u32 base, u32 size)
+{
+ writel(0, GPMC_CONFIG7 + gpmc_base);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], GPMC_CONFIG1 + gpmc_base);
+ writel(gpmc_config[1], GPMC_CONFIG2 + gpmc_base);
+ writel(gpmc_config[2], GPMC_CONFIG3 + gpmc_base);
+ writel(gpmc_config[3], GPMC_CONFIG4 + gpmc_base);
+ writel(gpmc_config[4], GPMC_CONFIG5 + gpmc_base);
+ writel(gpmc_config[5], GPMC_CONFIG6 + gpmc_base);
+ /* Enable the config */
+ writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
+ (1 << 6)), GPMC_CONFIG7 + gpmc_base);
+ sdelay(2000);
+}
+
+/*****************************************************
+ * gpmc_init(): init gpmc bus
+ * Init GPMC for x16, MuxMode (SDRAM in x32).
+ * This code can only be executed from SRAM or SDRAM.
+ *****************************************************/
+void gpmc_init(void)
+{
+ /* putting a blanket check on GPMC based on ZeBu for now */
+ u32 mux = 0, mwidth;
+ u32 *gpmc_config = NULL;
+ u32 gpmc_base = 0;
+ u32 base = 0;
+ u32 size = 0;
+ u32 f_off = CONFIG_SYS_MONITOR_LEN;
+ u32 f_sec = 0;
+ u32 config = 0;
+
+ mux = BIT9;
+ mwidth = get_gpmc0_width();
+
+ /* global settings */
+ writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */
+ writel(0, GPMC_TIMEOUT_CONTROL); /* timeout disable */
+
+ config = readl(GPMC_CONFIG);
+ config &= (~0xf00);
+ writel(config, GPMC_CONFIG);
+
+ /* Disable the GPMC0 config set by ROM code
+ * It conflicts with our MPDB (both at 0x08000000)
+ */
+ writel(0, GPMC_CONFIG7 + GPMC_CONFIG_CS0);
+ sdelay(1000);
+
+#if defined(CONFIG_CMD_NAND) /* CS 0 */
+ gpmc_config = gpmc_m_nand;
+#if defined(CONFIG_ENV_IS_IN_NAND)
+ gpmc_base = GPMC_CONFIG_CS0 + (0 * GPMC_CONFIG_WIDTH);
+#else
+ gpmc_base = GPMC_CONFIG_CS0 + (1 * GPMC_CONFIG_WIDTH);
+#endif
+ base = PISMO1_NAND_BASE;
+ size = PISMO1_NAND_SIZE;
+ enable_gpmc_config(gpmc_config, gpmc_base, base, size);
+ is_nand = 1;
+ nand_cs_base = gpmc_base;
+#if defined(CONFIG_ENV_IS_IN_NAND)
+ f_off = SMNAND_ENV_OFFSET;
+ f_sec = SZ_128K;
+ /* env setup */
+ boot_flash_base = base;
+ boot_flash_off = f_off;
+ boot_flash_sec = f_sec;
+ boot_flash_env_addr = f_off;
+#endif
+#endif
+
+#if defined(CONFIG_CMD_ONENAND)
+ gpmc_config = gpmc_onenand;
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ gpmc_base = GPMC_CONFIG_CS0 + (0 * GPMC_CONFIG_WIDTH);
+#else
+ gpmc_base = GPMC_CONFIG_CS0 + (1 * GPMC_CONFIG_WIDTH);
+#endif
+ base = PISMO1_ONEN_BASE;
+ size = PISMO1_ONEN_SIZE;
+ enable_gpmc_config(gpmc_config, gpmc_base, base, size);
+ is_onenand = 1;
+ onenand_cs_base = gpmc_base;
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ f_off = ONENAND_ENV_OFFSET;
+ f_sec = SZ_128K;
+ /* env setup */
+ boot_flash_base = base;
+ boot_flash_off = f_off;
+ boot_flash_sec = f_sec;
+ boot_flash_env_addr = f_off;
+#endif
+#endif
+
+#ifdef ENV_IS_VARIABLE
+ boot_env_get_char_spec = env_get_char_spec;
+ boot_env_init = env_init;
+ boot_saveenv = saveenv;
+ boot_env_relocate_spec = env_relocate_spec;
+#endif
+}
Index: u-boot-arm/cpu/arm_cortexa8/omap3/syslib.c
===================================================================
--- /dev/null
+++ u-boot-arm/cpu/arm_cortexa8/omap3/syslib.c
@@ -0,0 +1,72 @@
+/*
+ * (C) Copyright 2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Syed Mohammed Khasim <khasim at ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/bits.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/clocks.h>
+#include <asm/arch/sys_proto.h>
+
+/************************************************************
+ * sdelay() - simple spin loop. Will be constant time as
+ * its generally used in bypass conditions only. This
+ * is necessary until timers are accessible.
+ *
+ * not inline to increase chances its in cache when called
+ *************************************************************/
+void sdelay(unsigned long loops)
+{
+ __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
+ "bne 1b":"=r" (loops):"0"(loops));
+}
+
+/*****************************************************************
+ * sr32 - clear & set a value in a bit range for a 32 bit address
+ *****************************************************************/
+void sr32(u32 addr, u32 start_bit, u32 num_bits, u32 value)
+{
+ u32 tmp, msk = 0;
+ msk = 1 << num_bits;
+ --msk;
+ tmp = readl(addr) & ~(msk << start_bit);
+ tmp |= value << start_bit;
+ writel(tmp, addr);
+}
+
+/*********************************************************************
+ * wait_on_value() - common routine to allow waiting for changes in
+ * volatile regs.
+ *********************************************************************/
+u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound)
+{
+ u32 i = 0, val;
+ do {
+ ++i;
+ val = readl(read_addr) & read_bit_mask;
+ if (val == match_value)
+ return 1;
+ if (i == bound)
+ return 0;
+ } while (1);
+}
Index: u-boot-arm/cpu/arm_cortexa8/omap3/Makefile
===================================================================
--- u-boot-arm.orig/cpu/arm_cortexa8/omap3/Makefile
+++ u-boot-arm/cpu/arm_cortexa8/omap3/Makefile
@@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk
LIB = lib$(SOC).a
SOBJS := lowlevel_init.o
-OBJS := sys_info.o board.o clock.o interrupts.o
+OBJS := sys_info.o board.o clock.o interrupts.o mem.o syslib.o
all: .depend $(LIB)
Index: u-boot-arm/examples/Makefile
===================================================================
--- u-boot-arm.orig/examples/Makefile
+++ u-boot-arm/examples/Makefile
@@ -30,10 +30,12 @@ LOAD_ADDR = 0x40000
endif
ifeq ($(ARCH),arm)
+LOAD_ADDR = 0xc100000
ifeq ($(BOARD),omap2420h4)
LOAD_ADDR = 0x80300000
-else
-LOAD_ADDR = 0xc100000
+endif
+ifeq ($(CPU),omap3)
+LOAD_ADDR = 0x80300000
endif
endif
More information about the U-Boot
mailing list