[U-Boot] [PATCH] mcx: support for HTKW mcx board

Igor Grinberg grinberg at compulab.co.il
Thu Oct 6 10:18:47 CEST 2011


Hi Ilya,

On 10/06/11 01:42, Ilya Yanok wrote:
> This patch adds support for the HTKW mcx AM3517-based board.
> Serial, Ethernet, NAND and MMC are supported.
> 
> Signed-off-by: Ilya Yanok <yanok at emcraft.com>
> ---
>  MAINTAINERS              |    4 +
>  board/htkw/mcx/Makefile  |   44 +++++
>  board/htkw/mcx/config.mk |   27 +++
>  board/htkw/mcx/mcx.c     |   98 +++++++++++
>  board/htkw/mcx/mcx.h     |  425 ++++++++++++++++++++++++++++++++++++++++++++++
>  boards.cfg               |    1 +
>  include/configs/mcx.h    |  351 ++++++++++++++++++++++++++++++++++++++
>  7 files changed, 950 insertions(+), 0 deletions(-)
>  create mode 100644 board/htkw/mcx/Makefile
>  create mode 100644 board/htkw/mcx/config.mk
>  create mode 100644 board/htkw/mcx/mcx.c
>  create mode 100644 board/htkw/mcx/mcx.h
>  create mode 100644 include/configs/mcx.h
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3ab38fa..011141f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -878,6 +878,10 @@ Richard Woodruff <r-woodruff2 at ti.com>
>  
>  	omap2420h4	ARM1136EJS
>  
> +Ilya Yanok <yanok at emcraft.com>
> +
> +	mcx		ARM ARMV7 (AM35x SoC)
> +
>  Syed Mohammed Khasim <sm.khasim at gmail.com>
>  Sughosh Ganu <urwithsughosh at gmail.com>
>  
> diff --git a/board/htkw/mcx/Makefile b/board/htkw/mcx/Makefile
> new file mode 100644
> index 0000000..5d29458
> --- /dev/null
> +++ b/board/htkw/mcx/Makefile
> @@ -0,0 +1,44 @@
> +#
> +# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> +#
> +# Based on ti/evm/Makefile
> +#
> +# This program is free software; you can redistribute it and/or modify
> +# it under the terms of the GNU General Public License as published by
> +# the Free Software Foundation; either version 2 of the License, or
> +# (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

I know you just copied the above from another location, but
please, remove the address of FSF, it can change and I think
you will not follow the FSF address and will not submit patch to change it.
This holds for all new files.

> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB	= $(obj)lib$(BOARD).o
> +
> +COBJS	:= $(BOARD).o
> +
> +SRCS	:= $(COBJS:.o=.c)
> +OBJS	:= $(addprefix $(obj),$(COBJS))
> +
> +$(LIB):	$(obj).depend $(OBJS)
> +	$(call cmd_link_o_target, $(OBJS))
> +
> +clean:
> +	rm -f $(OBJS)
> +
> +distclean:	clean
> +	rm -f $(LIB) core *.bak $(obj).depend
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> diff --git a/board/htkw/mcx/config.mk b/board/htkw/mcx/config.mk
> new file mode 100644
> index 0000000..699a317
> --- /dev/null
> +++ b/board/htkw/mcx/config.mk

You don't need this file, please remove.

> @@ -0,0 +1,27 @@
> +#
> +# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> +#
> +# Based on ti/evm/config.mk
> +#
> +# This program is free software; you can redistribute it and/or modify
> +# it under the terms of the GNU General Public License as published by
> +# the Free Software Foundation; either version 2 of the License, or
> +# (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> +#
> +# Physical Address:
> +# 8000'0000 (bank0)
> +# A000/0000 (bank1)
> +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
> +# (mem base + reserved)
> +
> +# For use with external or internal boots.
> +CONFIG_SYS_TEXT_BASE = 0x80008000

This should be put inside the board config file.

> diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
> new file mode 100644
> index 0000000..aa490f0
> --- /dev/null
> +++ b/board/htkw/mcx/mcx.c
> @@ -0,0 +1,98 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on ti/evm/evm.c
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/mem.h>
> +#include <asm/arch/mux.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/mach-types.h>
> +#include <asm/omap_gpio.h>
> +#include <i2c.h>
> +#include "mcx.h"
> +
> +#define AM3517_IP_SW_RESET	0x48002598
> +#define CPGMACSS_SW_RST		(1 << 1)
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +/*
> + * Routine: board_init
> + * Description: Early hardware init.
> + */
> +int board_init(void)
> +{
> +	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
> +	/* board id for Linux */
> +	gd->bd->bi_arch_number = MACH_TYPE_MCX;

There is a new standard for setting the machine id for Linux.
CONFIG_MACH_TYPE must be used to allow the common code set the id.
Please, see the README file.

> +	/* boot param addr */
> +	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
> +
> +	return 0;
> +}
> +
> +/*
> + * Routine: misc_init_r
> + * Description: Init i2c, ethernet, etc... (done here so udelay works)
> + */
> +int misc_init_r(void)
> +{
> +#if defined(CONFIG_DRIVER_TI_EMAC)
> +	u32 reset;
> +#endif
> +#ifdef CONFIG_DRIVER_OMAP34XX_I2C
> +	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> +#endif

Why do you need the i2c_init() called here?
It is already called in arch/arm/lib/board.c before the misc_init_r().

> +
> +	dieid_num_r();
> +
> +#if defined(CONFIG_DRIVER_TI_EMAC)
> +	/*ensure that the module is out of reset*/
> +	reset = readl(AM3517_IP_SW_RESET);
> +	reset &= (~CPGMACSS_SW_RST);
> +	writel(reset,AM3517_IP_SW_RESET);
> +
> +#endif
> +	return 0;
> +}
> +
> +/*
> + * Routine: set_muxconf_regs
> + * Description: Setting up the configuration Mux registers specific to the
> + *		hardware. Many pins need to be moved from protect to primary
> + *		mode.
> + */
> +void set_muxconf_regs(void)
> +{
> +	MUX_MCX();
> +}
> +
> +/*
> + * Initializes on-chip ethernet controllers.
> + * to override, implement board_eth_init()
> + */
> +int cpu_eth_init(bd_t *bis)
> +{
> +#if defined(CONFIG_DRIVER_TI_EMAC)
> +	printf("davinci_emac_initialize\n");
> +	davinci_emac_initialize();
> +#endif
> +	return 0;
> +}

I don't mind that this will be done here,
but somehow it looks like some common AM35xx location should be used.

> diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
> new file mode 100644
> index 0000000..1ba0300
> --- /dev/null
> +++ b/board/htkw/mcx/mcx.h
> @@ -0,0 +1,425 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on ti/evm/evm.h
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#ifndef _AM3517EVM_H_
> +#define _AM3517EVM_H_
> +
> +const omap3_sysinfo sysinfo = {
> +	DDR_DISCRETE,
> +	"HTKW mcx Board",
> +	"NAND",
> +};
> +/* AM3517 specific mux configuration */
> +#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
> +/* CCDC */
> +#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
> +#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
> +#define CONTROL_PADCONF_CCDC_HD		0x01E8
> +#define CONTROL_PADCONF_CCDC_VD		0x01EA
> +#define CONTROL_PADCONF_CCDC_WEN	0x01EC
> +#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
> +#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
> +#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
> +#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
> +#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
> +#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
> +#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
> +#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
> +/* RMII */
> +#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
> +#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
> +#define CONTROL_PADCONF_RMII_RXD0	0x0202
> +#define CONTROL_PADCONF_RMII_RXD1	0x0204
> +#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
> +#define CONTROL_PADCONF_RMII_RXER	0x0208
> +#define CONTROL_PADCONF_RMII_TXD0	0x020A
> +#define CONTROL_PADCONF_RMII_TXD1	0x020C
> +#define CONTROL_PADCONF_RMII_TXEN	0x020E
> +#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
> +#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
> +/* CAN */
> +#define CONTROL_PADCONF_HECC1_TXD	0x0214
> +#define CONTROL_PADCONF_HECC1_RXD	0x0216
> +
> +#define CONTROL_PADCONF_SYS_BOOT7	0x0218
> +#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
> +#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
> +#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
> +#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
> +#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
> +#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
> +#define CONTROL_PADCONF_SYS_BOOT8	0x0226

Same here, all the above stuff, should be put in a common location.

> +
> +/*
> + * IEN  - Input Enable
> + * IDIS - Input Disable
> + * PTD  - Pull type Down
> + * PTU  - Pull type Up
> + * DIS  - Pull type selection is inactive
> + * EN   - Pull type selection is active
> + * M0   - Mode 0
> + * The commented string gives the final mux configuration for that pin
> + */
> +#define MUX_MCX() \
> +	/* SDRC */\
> +	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SDRC_DQS0N),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(SDRC_DQS1N),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(SDRC_DQS2N),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(SDRC_DQS3N),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(SDRC_CKE0),		(M0)) \
> +	MUX_VAL(CP(SDRC_CKE1),		(M0)) \
> +	MUX_VAL(CP(STRBEN_DLY0),	(IEN  | PTD | EN  | M0)) /*sdrc_strben_dly0*/\
> +	MUX_VAL(CP(STRBEN_DLY1),	(IEN  | PTD | EN  | M0)) /*sdrc_strben_dly1*/\
> +	/* GPMC */\
> +	MUX_VAL(CP(GPMC_A1),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A2),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A3),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A4),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A5),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A6),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A7),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A8),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A9),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | DIS | M4)) /* GPIO_43 LCD buffer enable */ \
> +	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_NCS1),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_NCS2),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_NCS3),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_NCS4),		(IEN | PTU | EN  | M4))\
> +	MUX_VAL(CP(GPMC_NCS5),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_NCS6),		(IEN | PTU | EN  | M4))/* GPIO_57 TS_PenIRQn */\
> +	MUX_VAL(CP(GPMC_NCS7),		(IEN | PTU | EN  | M4)) /* GPIO_58 ETHERNET RESET */\
> +	MUX_VAL(CP(GPMC_CLK),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTU | DIS  | M4))/* GPIO_61 SD-CARD CD */ \
> +        MUX_VAL(CP(GPMC_NWP),           (IDIS  | PTU | EN | M4))/* GPIO_62 Nand write protect, keep enabled */ \
> +	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(GPMC_WAIT1),		(IEN | PTU | EN  | M4))\
> +	MUX_VAL(CP(GPMC_WAIT2),		(IEN  | PTU | EN  | M4))\
> +	MUX_VAL(CP(GPMC_WAIT3),		(IEN | PTU | EN  | M4))/* GPIO_65 SD-CARD WP */\
> +	/* DSS */\
> +	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA0),		(IEN | PTU | EN  | M4))\
> +	MUX_VAL(CP(DSS_DATA1),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA2),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA8),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA9),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0))\
> +	MUX_VAL(CP(DSS_DATA16),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA17),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA18),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M0))  \
> +	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M0)) \
> +	/* CAMERA */\
> +	MUX_VAL(CP(CAM_HS),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(CAM_VS),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(CAM_XCLKA),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_PCLK),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(CAM_FLD),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D0),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D1),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D2),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D3),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D4),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D5),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D6),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D7),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D8),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D9),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D10),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_D11),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_XCLKB),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_WEN),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CAM_STROBE),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CSI2_DY1),		(IEN  | PTD | EN  | M4)) \
> +	/* MMC */\
> +	MUX_VAL(CP(MMC1_CLK),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M4)) \
> +	\
> +	MUX_VAL(CP(MMC2_CLK),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(MMC2_CMD),		(IDIS | PTD | DIS | M4)) /* GPIO_131 LCD Enable */ \
> +	MUX_VAL(CP(MMC2_DAT0),		(IDIS | PTD | DIS  | M4)) /* GPIO_132 USB host Enable */\
> +	MUX_VAL(CP(MMC2_DAT1),		(IDIS  | PTD | DIS  | M4)) /*GPIO_133 HDMI PD */\
> +	MUX_VAL(CP(MMC2_DAT2),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MMC2_DAT3),		(IEN  | PTU | EN  | M4))\
> +	/* McBSP */\
> +	MUX_VAL(CP(MCBSP_CLKS),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(MCBSP1_CLKR),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCBSP1_FSR),		(IDIS | PTU | EN  | M0)) \
> +	MUX_VAL(CP(MCBSP1_DX),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCBSP1_DR),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCBSP1_FSX),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCBSP1_CLKX),	(IEN  | PTD | DIS | M0)) \
> +	\
> +	MUX_VAL(CP(MCBSP2_FSX),		(IEN  | PTU | EN  | M4))\
> +	MUX_VAL(CP(MCBSP2_CLKX),	(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCBSP2_DR),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCBSP2_DX),		(IEN  | PTU | EN  | M4))\
> +	\
> +	MUX_VAL(CP(MCBSP3_DX),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCBSP3_CLKX),	(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCBSP3_FSX),		(IEN  | PTU | EN  | M4))\
> +	\
> +	MUX_VAL(CP(MCBSP4_CLKX),	(IDIS | PTD | DIS | M4)) /*GPIO_152 USB phy2 reset*/\
> +	MUX_VAL(CP(MCBSP4_DR),		(IEN | PTU | EN | M4)) /*GPIO_153*/\
> +	MUX_VAL(CP(MCBSP4_DX),		(IDIS | PTD | DIS | M4)) /*GPIO_154 USB phy1 reset*/\
> +	MUX_VAL(CP(MCBSP4_FSX),		(IEN | PTU | EN | M4)) /*GPIO_155 TS_BUSY*/\
> +	/* UART */\
> +	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0)) \
> +	\
> +	MUX_VAL(CP(UART2_CTS),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M0)) \
> +	\
> +	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTU | DIS | M0)) \
> +	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)) \
> +	/* I2C */\
> +	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(I2C4_SDA),		(IEN  | PTU | EN  | M0)) \
> +	/* McSPI */\
> +	MUX_VAL(CP(MCSPI1_CLK),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCSPI1_SIMO),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCSPI1_SOMI),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(MCSPI1_CS0),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(MCSPI1_CS1),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTU | EN  | M4)) \
> +	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M3)) /* HSUSB2_dat7 */\
> +	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M3)) /* HSUSB2_dat4 */\
> +	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M3)) /* HSUSB2_dat5 */\
> +	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | DIS | M3)) /* HSUSB2_dat6 */\
> +	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | DIS | M3)) /* HSUSB2_dat3 */\
> +	/* CCDC */\
> +	MUX_VAL(CP(CCDC_PCLK),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_FIELD),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_HD),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_VD),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_WEN),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA0),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA1),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA2),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA3),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA4),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA5),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA6),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(CCDC_DATA7),		(IEN  | PTD | EN  | M4)) \
> +	/* RMII */\
> +	MUX_VAL(CP(RMII_MDIO_DATA),	(IEN  |  M0)) \
> +	MUX_VAL(CP(RMII_MDIO_CLK),	(M0)) \
> +	MUX_VAL(CP(RMII_RXD0)	,	(IEN  | PTD | M0)) \
> +	MUX_VAL(CP(RMII_RXD1),		(IEN  | PTD | M0)) \
> +	MUX_VAL(CP(RMII_CRS_DV),	(IEN  | PTD | M0)) \
> +	MUX_VAL(CP(RMII_RXER),		(PTD | M0)) \
> +	MUX_VAL(CP(RMII_TXD0),		(PTD | M0)) \
> +	MUX_VAL(CP(RMII_TXD1),		(PTD | M0)) \
> +	MUX_VAL(CP(RMII_TXEN),		(PTD | M0)) \
> +	MUX_VAL(CP(RMII_50MHZ_CLK),	(IEN  | PTD | EN  | M0)) \
> +	/* HECC */\
> +	MUX_VAL(CP(HECC1_TXD),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(HECC1_RXD),		(IEN  | PTD | EN  | M4)) \
> +	/* HSUSB */\
> +	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)) \
> +	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(USB0_DRVBUS),	(IEN  | PTD | EN  | M0)) \
> +	/* HDQ */\
> +	MUX_VAL(CP(HDQ_SIO),		(IEN  | PTD | EN  | M4)) \
> +	/* Control and debug */\
> +	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTD | EN  | M4)) \
> +	MUX_VAL(CP(SYS_NRESWARM),     	(IEN | PTU | DIS | M4)) /*SYS_nRESWARM */\
> +	MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT3),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT4),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT5),		(IEN  | PTD | DIS | M4))\
> +	MUX_VAL(CP(SYS_BOOT6),		(IEN  | PTD | DIS | M4))\
> +	MUX_VAL(CP(SYS_BOOT7),		(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(SYS_BOOT8),		(IEN  | PTD | DIS | M4)) \
> +	\
> +	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M4))\
> +	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4))\
> +	/* JTAG */\
> +	MUX_VAL(CP(JTAG_nTRST),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(JTAG_TCK),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(JTAG_TMS),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(JTAG_TDI),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(JTAG_EMU0),		(IEN | PTU | EN  | M4)) \
> +	MUX_VAL(CP(JTAG_EMU1),		(IEN | PTU | EN  | M4))\
> +	/* ETK (ES2 onwards) */\
> +	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS  | PTD | DIS | M3))/* hsusb1_stp */ \
> +	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS  | PTD | DIS | M3)) /*hsusb1_clk*/\
> +	MUX_VAL(CP(ETK_D0_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D1_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D2_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D3_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D4_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D5_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D6_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D7_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D8_ES2 ),	(IEN  | PTD | EN | M3))\
> +	MUX_VAL(CP(ETK_D9_ES2 ),	(IEN  | PTD | EN | M3)) \
> +	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M4)) \
> +	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M4))\
> +	/* Die to Die */\
> +	MUX_VAL(CP(D2D_MCAD34),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_MCAD35),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_MCAD36),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_CLK26MI),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_NRESPWRON),	(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_NRESWARM),	(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(D2D_ARM9NIRQ),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_UMA2P6FIQ),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_SPINT),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_FRINT),		(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_DMAREQ0),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_DMAREQ1),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_DMAREQ2),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_DMAREQ3),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GTRST),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GTDI),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GTDO),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GTMS),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GTCK),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_N3GRTCK),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_MSTDBY),		(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(D2D_SWAKEUP),	(IEN  | PTD | EN  | M0)) \
> +	MUX_VAL(CP(D2D_IDLEREQ),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_IDLEACK),	(IEN  | PTU | EN  | M0)) \
> +	MUX_VAL(CP(D2D_MWRITE),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_SWRITE),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_MREAD),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_SREAD),		(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) \
> +	MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) \
> +
> +#endif
> diff --git a/boards.cfg b/boards.cfg
> index 65482ac..ac20b3d 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -183,6 +183,7 @@ omap3_beagle                 arm         armv7       beagle              ti
>  omap3_evm                    arm         armv7       evm                 ti             omap3
>  omap3_sdp3430                arm         armv7       sdp3430             ti             omap3
>  devkit8000                   arm         armv7       devkit8000          timll          omap3
> +mcx                          arm         armv7       mcx                 htkw           omap3
>  omap4_panda                  arm         armv7       panda               ti             omap4
>  omap4_sdp4430                arm         armv7       sdp4430             ti             omap4
>  s5p_goni                     arm         armv7       goni                samsung        s5pc1xx
> diff --git a/include/configs/mcx.h b/include/configs/mcx.h
> new file mode 100644
> index 0000000..a33afa5
> --- /dev/null
> +++ b/include/configs/mcx.h
> @@ -0,0 +1,351 @@
> +/*
> + * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
> + *
> + * Based on omap3_evm_config.h
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/*
> + * High Level Configuration Options
> + */
> +#define CONFIG_OMAP		1	/* in a TI OMAP core */
> +#define CONFIG_OMAP34XX		1	/* which is a 34XX */
> +#define CONFIG_OMAP3_MCX	1	/* working with mcx */

Boolean CONFIG_* options should not have a value.
Please, fix globally.

> +
> +#define CONFIG_EMIF4	/* The chip has EMIF4 controller */
> +
> +#include <asm/arch/cpu.h>		/* get chip and board defs */
> +#include <asm/arch/omap3.h>
> +
> +#define CONFIG_OF_LIBFDT		1
> +#define CONFIG_FIT			1
> +
> +/*
> + * Display CPU and Board information
> + */
> +#define CONFIG_DISPLAY_CPUINFO		1
> +#define CONFIG_DISPLAY_BOARDINFO	1
> +
> +/* Clock Defines */
> +#define V_OSCK			26000000	/* Clock output from T2 */
> +#define V_SCLK			(V_OSCK >> 1)
> +
> +#undef CONFIG_USE_IRQ				/* no support for IRQs */
> +#define CONFIG_MISC_INIT_R
> +
> +#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
> +#define CONFIG_SETUP_MEMORY_TAGS	1
> +#define CONFIG_INITRD_TAG		1
> +#define CONFIG_REVISION_TAG		1
> +
> +/*
> + * Size of malloc() pool
> + */
> +#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB sector */
> +#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
> +/*
> + * DDR related
> + */
> +#define CONFIG_OMAP3_MICRON_DDR		1	/* Micron DDR */
> +#define CONFIG_SYS_CS0_SIZE		(256 * 1024 * 1024)
> +
> +/*
> + * Hardware drivers
> + */
> +
> +/*
> + * NS16550 Configuration
> + */
> +#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
> +
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
> +#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
> +
> +/*
> + * select serial console configuration
> + */
> +#define CONFIG_CONS_INDEX		3
> +#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
> +#define CONFIG_SERIAL3			3	/* UART3 */
> +
> +/* allow to overwrite serial and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_BAUDRATE			115200
> +#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
> +					115200}
> +#define CONFIG_MMC			1
> +#define CONFIG_OMAP3_MMC		1
> +#define CONFIG_GENERIC_MMC		1
> +#define CONFIG_DOS_PARTITION		1
> +
> +/*
> + * USB configuration
> + * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
> + * Enable CONFIG_MUSB_UDC for Device functionalities.
> + */
> +#define CONFIG_USB_AM35X		1
> +#define CONFIG_MUSB_HCD			1
> +
> +#ifdef CONFIG_USB_AM35X
> +
> +#ifdef CONFIG_MUSB_HCD
> +#define CONFIG_CMD_USB
> +
> +#define CONFIG_USB_STORAGE
> +#define CONGIG_CMD_STORAGE
> +#define CONFIG_CMD_FAT
> +
> +#ifdef CONFIG_USB_KEYBOARD
> +#define CONFIG_SYS_USB_EVENT_POLL
> +#define CONFIG_PREBOOT "usb start"
> +#endif /* CONFIG_USB_KEYBOARD */
> +
> +#endif /* CONFIG_MUSB_HCD */
> +
> +#ifdef CONFIG_MUSB_UDC
> +/* USB device configuration */
> +#define CONFIG_USB_DEVICE		1
> +#define CONFIG_USB_TTY			1
> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
> +/* Change these to suit your needs */
> +#define CONFIG_USBD_VENDORID		0x0451
> +#define CONFIG_USBD_PRODUCTID		0x5678
> +#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
> +#define CONFIG_USBD_PRODUCT_NAME	"AM3517EVM"

Don't you want to call it after your product name?

> +#endif /* CONFIG_MUSB_UDC */
> +
> +#endif /* CONFIG_USB_AM35X */
> +
> +/* commands to include */
> +#include <config_cmd_default.h>
> +
> +#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
> +#define CONFIG_CMD_FAT		/* FAT support			*/
> +#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
> +
> +#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
> +#define CONFIG_CMD_MMC		/* MMC support			*/
> +#define CONFIG_CMD_NAND		/* NAND support			*/
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_PING
> +
> +#undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
> +#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
> +#undef CONFIG_CMD_IMI		/* iminfo			*/
> +#undef CONFIG_CMD_IMLS		/* List all found images	*/
> +
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_HARD_I2C			1
> +#define CONFIG_SYS_I2C_SPEED		100000
> +#define CONFIG_SYS_I2C_SLAVE		1
> +#define CONFIG_SYS_I2C_BUS		0
> +#define CONFIG_SYS_I2C_BUS_SELECT	1
> +#define CONFIG_DRIVER_OMAP34XX_I2C	1
> +
> +#define CONFIG_CMD_NET
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NFS
> +/*
> + * Board NAND Info.
> + */
> +#define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
> +							/* to access nand */
> +#define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
> +							/* to access */
> +							/* nand at CS0 */
> +
> +#define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
> +							/* NAND devices */
> +#define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
> +
> +#define CONFIG_JFFS2_NAND
> +/* nand device jffs2 lives on */
> +#define CONFIG_JFFS2_DEV		"nand0"
> +/* start of jffs2 partition */
> +#define CONFIG_JFFS2_PART_OFFSET	0x680000
> +#define CONFIG_JFFS2_PART_SIZE		0xf980000	/* sz of jffs2 part */
> +
> +/* Environment information */
> +#define CONFIG_BOOTDELAY	10
> +
> +#define CONFIG_BOOTFILE		uImage
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> +	"loadaddr=0x82000000\0" \
> +	"console=ttyO2,115200n8\0" \
> +	"mmcargs=setenv bootargs console=${console} " \
> +		"root=/dev/mmcblk0p2 rw " \
> +		"rootfstype=ext3 rootwait\0" \
> +	"nandargs=setenv bootargs console=${console} " \
> +		"root=/dev/mtdblock4 rw " \
> +		"rootfstype=jffs2\0" \
> +	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
> +	"bootscript=echo Running bootscript from mmc ...; " \
> +		"source ${loadaddr}\0" \
> +	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
> +	"mmcboot=echo Booting from mmc ...; " \
> +		"run mmcargs; " \
> +		"bootm ${loadaddr}\0" \
> +	"nandboot=echo Booting from nand ...; " \
> +		"run nandargs; " \
> +		"nand read ${loadaddr} 280000 400000; " \
> +		"bootm ${loadaddr}\0" \
> +
> +#define CONFIG_BOOTCOMMAND \
> +	"if mmc init; then " \
> +		"if run loadbootscript; then " \
> +			"run bootscript; " \
> +		"else " \
> +			"if run loaduimage; then " \
> +				"run mmcboot; " \
> +			"else run nandboot; " \
> +			"fi; " \
> +		"fi; " \
> +	"else run nandboot; fi"
> +
> +#define CONFIG_AUTO_COMPLETE	1
> +/*
> + * Miscellaneous configurable options
> + */
> +#define V_PROMPT			"mcx # "
> +
> +#define CONFIG_SYS_LONGHELP		/* undef to save memory */
> +#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
> +#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> +#define CONFIG_SYS_PROMPT		V_PROMPT
> +#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
> +/* Print Buffer Size */
> +#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
> +					sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_MAXARGS		32	/* max number of command */
> +						/* args */
> +/* Boot Argument Buffer Size */
> +#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
> +/* memtest works on */
> +#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
> +#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
> +					0x01F00000) /* 31MB */
> +
> +#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
> +								/* address */
> +
> +/*
> + * AM3517 has 12 GP timers, they can be driven by the system clock
> + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
> + * This rate is divided by a local divisor.
> + */
> +#define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
> +#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
> +#define CONFIG_SYS_HZ			1000
> +
> +/*-----------------------------------------------------------------------
> + * Stack sizes
> + *
> + * The stack sizes are set up in start.S using the settings below
> + */
> +#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
> +#ifdef CONFIG_USE_IRQ
> +#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
> +#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
> +#endif
> +
> +/*-----------------------------------------------------------------------
> + * Physical Memory Map
> + */
> +#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
> +#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
> +#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
> +#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
> +
> +/* SDRAM Bank Allocation method */
> +#define SDRC_R_B_C		1
> +
> +/*-----------------------------------------------------------------------
> + * FLASH and environment organization
> + */
> +
> +/* **** PISMO SUPPORT *** */
> +
> +/* Configure the PISMO */
> +#define PISMO1_NAND_SIZE		GPMC_SIZE_128M
> +#define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
> +
> +#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors */
> +						/* on one chip */
> +#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
> +#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
> +
> +#if defined(CONFIG_CMD_NAND)
> +#define CONFIG_SYS_FLASH_BASE		PISMO1_NAND_BASE
> +#endif
> +
> +/* Monitor at start of flash */
> +#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
> +
> +#define CONFIG_NAND_OMAP_GPMC
> +#define GPMC_NAND_ECC_LP_x16_LAYOUT	1
> +#define CONFIG_ENV_IS_IN_NAND		1
> +#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
> +
> +#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
> +#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
> +#define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
> +
> +/*-----------------------------------------------------------------------
> + * CFI FLASH driver setup
> + */
> +/* timeout values are in ticks */
> +#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
> +#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
> +
> +/* Flash banks JFFS2 should use */
> +#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
> +					CONFIG_SYS_MAX_NAND_DEVICE)
> +#define CONFIG_SYS_JFFS2_MEM_NAND
> +/* use flash_info[2] */
> +#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
> +#define CONFIG_SYS_JFFS2_NUM_BANKS	1
> +
> +#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
> +#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
> +#define CONFIG_SYS_INIT_RAM_SIZE	0x800
> +#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
> +					 CONFIG_SYS_INIT_RAM_SIZE - \
> +					 GENERATED_GBL_DATA_SIZE)
> +
> +/*
> + * ethernet support
> + *
> + */
> +#if defined(CONFIG_CMD_NET)
> +#define CONFIG_DRIVER_TI_EMAC
> +#define CONFIG_DRIVER_TI_EMAC_USE_RMII
> +#define CONFIG_MII
> +#define CONFIG_EMAC_MDIO_PHY_NUM	0
> +#define	CONFIG_BOOTP_DEFAULT
> +#define CONFIG_BOOTP_DNS
> +#define CONFIG_BOOTP_DNS2
> +#define CONFIG_BOOTP_SEND_HOSTNAME
> +#define CONFIG_NET_RETRY_COUNT 10
> +#define CONFIG_NET_MULTI
> +#endif
> +
> +#endif /* __CONFIG_H */

-- 
Regards,
Igor.


More information about the U-Boot mailing list