[U-Boot] [PATCH v3 4/7] tegra: usb: move controller init into start_port

Lucas Stach dev at lynxeye.de
Thu Feb 7 18:16:27 CET 2013


There is no need to init a USB controller before the upper layers indicate
that they are actually going to use it.

board_usb_init now only parses the device tree and sets up the common pll.

Signed-off-by: Lucas Stach <dev at lynxeye.de>
Acked-by: Simon Glass <sjg at chromium.org>
---
v2:
- remember if port is already initialized and skip init in that case
---
 arch/arm/cpu/armv7/tegra20/usb.c | 57 ++++++++++++++++++++--------------------
 1 file changed, 29 insertions(+), 28 deletions(-)

diff --git a/arch/arm/cpu/armv7/tegra20/usb.c b/arch/arm/cpu/armv7/tegra20/usb.c
index 2007483..e4165e0 100644
--- a/arch/arm/cpu/armv7/tegra20/usb.c
+++ b/arch/arm/cpu/armv7/tegra20/usb.c
@@ -79,6 +79,7 @@ struct fdt_usb {
 	unsigned ulpi:1;	/* 1 if port has external ULPI transceiver */
 	unsigned enabled:1;	/* 1 to enable, 0 to disable */
 	unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */
+	unsigned initialized:1; /* has this port already been initialized? */
 	enum dr_mode dr_mode;	/* dual role mode */
 	enum periph_id periph_id;/* peripheral id */
 	struct fdt_gpio_state vbus_gpio;	/* GPIO for vbus enable */
@@ -426,44 +427,36 @@ static void config_clock(const u32 timing[])
 		timing[PARAM_CPCON], timing[PARAM_LFCON]);
 }
 
-/**
- * Add a new USB port to the list of available ports.
- *
- * @param config	USB port configuration
- * @return 0 if ok, -1 if error (too many ports)
- */
-static int add_port(struct fdt_usb *config)
+int tegrausb_start_port(int portnum, u32 *hccr, u32 *hcor)
 {
-	if (port_count == USB_PORTS_MAX) {
-		printf("tegrausb: Cannot register more than %d ports\n",
-		      USB_PORTS_MAX);
+	struct fdt_usb *config;
+	struct usb_ctlr *usbctlr;
+
+	if (portnum >= port_count)
 		return -1;
-	}
+
+	config = &port[portnum];
+
+	/* skip init, if the port is already initialized */
+	if (config->initialized)
+		goto success;
 
 	if (config->utmi && init_utmi_usb_controller(config)) {
-		printf("tegrausb: Cannot init port\n");
+		printf("tegrausb: Cannot init port %d\n", portnum);
 		return -1;
 	}
 
 	if (config->ulpi && init_ulpi_usb_controller(config)) {
-		printf("tegrausb: Cannot init port\n");
+		printf("tegrausb: Cannot init port %d\n", portnum);
 		return -1;
 	}
 
-	port[port_count++] = *config;
-
-	return 0;
-}
-
-int tegrausb_start_port(int portnum, u32 *hccr, u32 *hcor)
-{
-	struct usb_ctlr *usbctlr;
+	set_host_mode(config);
 
-	if (portnum >= port_count)
-		return -1;
-	set_host_mode(&port[portnum]);
+	config->initialized = 1;
 
-	usbctlr = port[portnum].reg;
+success:
+	usbctlr = config->reg;
 	*hccr = (u32)&usbctlr->cap_length;
 	*hcor = (u32)&usbctlr->usb_cmd;
 	return 0;
@@ -483,6 +476,8 @@ int tegrausb_stop_port(int portnum)
 	writel(2, &usbctlr->usb_cmd);
 	udelay(1000);
 
+	port[portnum].initialized = 0;
+
 	return 0;
 }
 
@@ -546,6 +541,12 @@ int board_usb_init(const void *blob)
 	count = fdtdec_find_aliases_for_id(blob, "usb",
 			COMPAT_NVIDIA_TEGRA20_USB, node_list, USB_PORTS_MAX);
 	for (i = 0; i < count; i++) {
+		if (port_count == USB_PORTS_MAX) {
+			printf("tegrausb: Cannot register more than %d ports\n",
+				USB_PORTS_MAX);
+			return -1;
+		}
+
 		debug("USB %d: ", i);
 		node = node_list[i];
 		if (!node)
@@ -555,10 +556,10 @@ int board_usb_init(const void *blob)
 			      fdt_get_name(blob, node, NULL));
 			return -1;
 		}
+		config.initialized = 0;
 
-		if (add_port(&config))
-			return -1;
-		set_host_mode(&config);
+		/* add new USB port to the list of available ports */
+		port[port_count++] = config;
 	}
 
 	return 0;
-- 
1.8.1



More information about the U-Boot mailing list