[U-Boot] booting os 'Unknown OS' (1) is not supported

[Alexander Khryukin]

Also if flashed 3.12_zImage (same kernel, same sources, just zImage)
i see this



reading kernel..device 0 Start 1063, Count 16384
MMC read: dev # 0, block # 1063, count 16384 ... 16384 blocks read: OK
completed
reading RFS..device 0 Count 17447, Start 2048
MMC read: dev # 0, block # 17447, count 2048 ... 2048 blocks read: OK
completed
Boot with zImage
Wrong Ramdisk Image Format

Starting kernel ...


And it's stucked at "Starting kernel ..."


2014/1/17 Alexander Khryukin <alexander at mezon.ru>

> Thanks.
> I changed env to
>
> baudrate=115200
> *bootcmd=movi read kernel 0 40800000;movi read rootfs 0 41000000
> 100000;bootm 40800000 41000000*
> bootdelay=3
> emmcbootrecovery=mmc erase boot 1 0 0;emmc open 1;movi read fwbl1 0
> 40000000;movi write zero fwbl1 1 40000000;movi read bl2 0 40004000;movi
> write zero bl2 1 40004000;movi read u-boot 0 42000000;movi write zero
> u-boot 1 42000000;movi read tzsw 0 42100000;movi write zero tzsw 1
> 42100000;emmc close 1
> ethact=smc911x-0
> ethaddr=00:40:5c:26:0a:5b
> gatewayip=192.168.0.1
> ipaddr=192.168.0.28
> netmask=255.255.255.0
> rootfslen= 100000
> serverip=192.168.0.13
>
>
>
> And now trying to boot
> U-Boot 2012.12-00000-g503cd8d-dirty (Jan 15 2014 - 12:58:49) for YICSYSTEM
> YSE5250-scp
>
>
> CPU: S5PC520 Rev1.0 [Samsung SOC on SMP Platform Base on ARM CortexA15]
> APLL = 800MHz, MPLL = 800MHz
> Board:  YSE5250-scp
> DRAM:  2047 MiB
>
> TrustZone Enabled BSP
> BL1 version: 20130404
> PMIC: S5M8767
>
>
> Checking Boot Mode ... SDMMC
> REVISION: 1.0
> REVISION: 1.0
> MMC Device 0: 3839 MB
> NAME: S5P_MSHC0
> MMC Device 1: 7348 MB
> MMC Device 2 not found
> Net:   smc911x-0
>
> Hit any key to stop autoboot:  0
> reading kernel..device 0 Start 1063, Count 16384
> MMC read: dev # 0, block # 1063, count 16384 ... 16384 blocks read: OK
> completed
> reading RFS..device 0 Count 17447, Start 2048
> MMC read: dev # 0, block # 17447, count 2048 ... 2048 blocks read: OK
> completed
> ## Booting kernel from Legacy Image at 40800000 ...
>    Image Name:   Linux-3.13.0-rc8
>
>    Image Type:   ARM Linux Kernel Image (uncompressed)
>    Data Size:    4754992 Bytes = 4643 KiB
>
>    Load Address: 40008000
>    Entry Point:  40008000
>    Verifying Checksum ... OK
> Wrong Ramdisk Image Format
>    Loading Kernel Image ... OK
> OK
>
> *ERROR: booting os 'Unknown OS' (1) is not supported*
>
>
> No changes.
> But XIP is gone.
>
>
>
> 2014/1/17 Detlev Zundel <dzu at denx.de>
>
>> Hello Alexander,
>>
>> > Thanks for your answer!
>> >
>> >>So again, try loading the image somewhere else in RAM and let U-Boot do
>> >>the copying to the correct place.
>> >
>> > It's not obvious for me how to do it.
>> > Might you have any guide or faq?
>>
>> [...]
>>
>> >> > ### main_loop: bootcmd="movi read kernel 0 40008000;movi read rootfs
>> 0
>>                              ^^^^^^^^^^^^^^^^^^^^^^^^^^^
>> >> > 41000000 100000;bootm 40008000 41000000"
>>                      ^^^^^^^^^^^^^^
>>
>> Your bootmcd reads the kernel to 40008000 and then calls bootm to that
>> address.  Simple change those two places to, say, 40800000 by editing
>> bootcmd.  (Not knowing your system, I presume RAM starts at 4000,0000
>> and 4080,0000 then would be 8MiB after the beginning.  U-Boot will copy
>> the kernel to 4008000 so the kernel should not be bigger than 7.5MiB but
>> the other snippets from your log say the kernel is ~3.2MiB, so this
>> should be fine.
>>
>> Cheers
>>   Detlev
>>
>> --
>> The only thing that interferes with my learning is my education.
>>                               -- Albert Einstein
>> --
>> DENX Software Engineering GmbH,      MD: Wolfgang Denk & Detlev Zundel
>> HRB 165235 Munich,  Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de
>>
>
>