[U-Boot] [RFC PATCH] ARM: Activate hypervisor mode for TI am5726 (OMAP5/dra7)

Lennart Sorensen lsorense at csclub.uwaterloo.ca
Tue Jan 27 20:32:35 CET 2015


On Tue, Jan 27, 2015 at 01:56:12PM -0500, Frank Bormann wrote:
> Hi,
> 
> I was wondering if I could have any input on the patch below activating
> hypervisor mode on TI OMAP5-based SoC. The patch essentially uses the
> on-chip ROM code API to enable hypervisor mode on the primary A15 core
> and goes in tandem with a Linux kernel patch recently accepted into
> omap-for-v3.19/fixes that checks hypervisor mode on the primary A15 core
> and sets it accordingly on additional cores being activated.
> 
> I am aware that there is some development going on for ARM's PSCI that
> amongst other things is supposed to deal with hypervisor activation in a
> more generic fashion and I am wondering if there is any preference on
> how to properly activate hypervisor mode for the TI SoCs mentioned above.
> 
> Thanks,
> Frank
> 
> ---------------
> 
> u-boot patch:
> 
> Enable hypervisor mode for AM5726

Well it actually applies to AM57xx and OMAP54xx as far as I can tell.

The DRA7XX (AM57xx) borrowed that part of the romcode from the OMAP5 as
far as I know.

Perhaps DRA7XX in the name should be something that applies to both TI
Cortex-A15 designs.  I don't know what the Keystone models do.

> ---
>  arch/arm/cpu/armv7/omap-common/lowlevel_init.S |   13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
> b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
> index 86c0e42..696da4b 100644
> --- a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
> +++ b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S
> @@ -19,7 +19,20 @@
>  ENTRY(save_boot_params)
>  	ldr	r1, =OMAP_SRAM_SCRATCH_BOOT_PARAMS
>  	str	r0, [r1]
> +/*
> + * Turn on hypervisor mode on CPU#0
> + */
> +#ifdef CONFIG_DRA7XX_HYPERVISOR_ON
> +	mov	r0, lr		@ This is a great place to switch into hyp mode
> +				@ only the r0 was needed from _start and is now
> +				@ free; all other general purpose registers were
> +				@ already free.
> +	ldr	r12, =0x102	@ Set PL310 control register - value in R0
> +	.word	0xe1600070	@ SMC #0 - hand assembled because -march=armv5
> +				@ call ROM Code API to set control register
> +#else
>  	bx	lr
> +#endif /* CONFIG_DRA7XX_HYPERVISOR_ON */
>  ENDPROC(save_boot_params)
>   ENTRY(set_pl310_ctrl_reg)
> 
> ---------------
> 
> Link to the corresponding Linux kernel patch:
> 
> http://linux-kernel.2935.n7.nabble.com/PATCH-ARM-omap5-dra7xx-Enable-booting-secondary-CPU-in-HYP-mode-td1009407.html#a1014616

-- 
Len Sorensen


More information about the U-Boot mailing list