[U-Boot] [PATCH v2 4/9] usb: ehci-mx6: introduce config for high active power pin

[Stefan Agner]

From: Stefan Agner <stefan.agner at toradex.com>

Add a new config CONFIG_MXC_USB_OTG_HACTIVE which configures the
OTG Power Pin to be high active. Low active is the reset value
of the affected configuration register, hence the config option
is named by the non-reset configuration.

Signed-off-by: Stefan Agner <stefan.agner at toradex.com>
---

 configs/mx7dsabresd_defconfig | 1 +
 configs/warp7_defconfig       | 1 +
 drivers/usb/host/Kconfig      | 9 +++++++++
 drivers/usb/host/ehci-mx6.c   | 4 ++++
 4 files changed, 15 insertions(+)

diff --git a/configs/mx7dsabresd_defconfig b/configs/mx7dsabresd_defconfig
index 9dbc9c7..d6dafcd 100644
--- a/configs/mx7dsabresd_defconfig
+++ b/configs/mx7dsabresd_defconfig
@@ -30,6 +30,7 @@ CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_FAT=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
 CONFIG_USB_GADGET=y
 CONFIG_CI_UDC=y
 CONFIG_USB_GADGET_DOWNLOAD=y
diff --git a/configs/warp7_defconfig b/configs/warp7_defconfig
index ba56c84..f0c165b 100644
--- a/configs/warp7_defconfig
+++ b/configs/warp7_defconfig
@@ -25,4 +25,5 @@ CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_FAT=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
 CONFIG_OF_LIBFDT=y
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 7992cb4..09db938 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -81,6 +81,15 @@ config USB_EHCI_MX7
 	---help---
 	  Enables support for the on-chip EHCI controller on i.MX7 SoCs.
 
+if USB_EHCI_MX7
+
+config MXC_USB_OTG_HACTIVE
+	bool "USB Power pin high active"
+	---help---
+	  Set the USB Power pin polarity to be high active (PWR_POL)
+
+endif
+
 config USB_EHCI_MSM
 	bool "Support for Qualcomm on-chip EHCI USB controller"
 	depends on DM_USB
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index 277f461..8352c2b 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -216,7 +216,11 @@ static void usb_power_config(int index)
 	clrbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
 
 	/* Set power polarity to high active */
+#ifdef CONFIG_MXC_USB_OTG_HACTIVE
 	setbits_le32(ctrl, UCTRL_PWR_POL);
+#else
+	clrbits_le32(ctrl, UCTRL_PWR_POL);
+#endif
 }
 
 int usb_phy_mode(int port)
-- 
2.9.0