[U-Boot] [PATCH] ARM: K2G: DDR3: Fix up priv ID for MPU

[Lokesh Vutla]

From: Nishanth Menon <nm at ti.com>

For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.

Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.

Signed-off-by: Nishanth Menon <nm at ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
---
 arch/arm/mach-keystone/ddr3.c | 23 +++++++++++++++++++----
 1 file changed, 19 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-keystone/ddr3.c b/arch/arm/mach-keystone/ddr3.c
index 6b92530..ee8e12e 100644
--- a/arch/arm/mach-keystone/ddr3.c
+++ b/arch/arm/mach-keystone/ddr3.c
@@ -138,7 +138,10 @@ static void ddr3_reset_data(u32 base, u32 ddr3_size)
 	puts("\nClear entire DDR3 memory to enable ECC\n");
 
 	/* save the SES MPAX regs */
-	msmc_get_ses_mpax(8, 0, mpax);
+	if (cpu_is_k2g())
+		msmc_get_ses_mpax(K2G_MSMC_SEGMENT_ARM, 0, mpax);
+	else
+		msmc_get_ses_mpax(K2HKLE_MSMC_SEGMENT_ARM, 0, mpax);
 
 	/* setup edma slot 1 configuration */
 	slot.opt = EDMA3_SLOPT_TRANS_COMP_INT_ENB |
@@ -169,8 +172,17 @@ static void ddr3_reset_data(u32 base, u32 ddr3_size)
 	for (seg = 0; seg < seg_num; seg += KS2_MSMC_MAP_SEG_NUM) {
 		/* map 2GB 36-bit DDR address to 32-bit DDR address in EMIF
 		   access slave interface so that edma driver can access */
-		msmc_map_ses_segment(8, 0, base >> KS2_MSMC_SEG_SIZE_SHIFT,
-				     KS2_MSMC_DST_SEG_BASE + seg, MPAX_SEG_2G);
+		if (cpu_is_k2g()) {
+			msmc_map_ses_segment(K2G_MSMC_SEGMENT_ARM, 0,
+					     base >> KS2_MSMC_SEG_SIZE_SHIFT,
+					     KS2_MSMC_DST_SEG_BASE + seg,
+					     MPAX_SEG_2G);
+		} else {
+			msmc_map_ses_segment(K2HKLE_MSMC_SEGMENT_ARM, 0,
+					     base >> KS2_MSMC_SEG_SIZE_SHIFT,
+					     KS2_MSMC_DST_SEG_BASE + seg,
+					     MPAX_SEG_2G);
+		}
 
 		if ((seg_num - seg) > KS2_MSMC_MAP_SEG_NUM)
 			edma_blks = KS2_MSMC_MAP_SEG_NUM <<
@@ -197,7 +209,10 @@ static void ddr3_reset_data(u32 base, u32 ddr3_size)
 	qedma3_stop(KS2_EDMA0_BASE, &edma_channel);
 
 	/* restore the SES MPAX regs */
-	msmc_set_ses_mpax(8, 0, mpax);
+	if (cpu_is_k2g())
+		msmc_set_ses_mpax(K2G_MSMC_SEGMENT_ARM, 0, mpax);
+	else
+		msmc_set_ses_mpax(K2HKLE_MSMC_SEGMENT_ARM, 0, mpax);
 }
 
 static void ddr3_ecc_init_range(u32 base)
-- 
2.10.1