[U-Boot] [PATCH v5 5/6] board: sama5d3_xplained: Clean up code

Wenyou Yang wenyou.yang at atmel.com
Fri Apr 14 00:51:46 UTC 2017


Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.

Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---

Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None

 board/atmel/sama5d3_xplained/sama5d3_xplained.c | 34 -------------------------
 1 file changed, 34 deletions(-)

diff --git a/board/atmel/sama5d3_xplained/sama5d3_xplained.c b/board/atmel/sama5d3_xplained/sama5d3_xplained.c
index 2b9da91b2d..f2f5506adc 100644
--- a/board/atmel/sama5d3_xplained/sama5d3_xplained.c
+++ b/board/atmel/sama5d3_xplained/sama5d3_xplained.c
@@ -6,16 +6,12 @@
  */
 
 #include <common.h>
-#include <mmc.h>
 #include <asm/io.h>
 #include <asm/arch/sama5d3_smc.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_rstc.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/clk.h>
-#include <atmel_mci.h>
-#include <net.h>
-#include <netdev.h>
 #include <spl.h>
 #include <asm/arch/atmel_mpddrc.h>
 #include <asm/arch/at91_wdt.h>
@@ -65,20 +61,12 @@ static void sama5d3_xplained_usb_hw_init(void)
 #ifdef CONFIG_GENERIC_ATMEL_MCI
 static void sama5d3_xplained_mci0_hw_init(void)
 {
-	at91_mci_hw_init();
-
 	at91_set_pio_output(AT91_PIO_PORTE, 2, 0);	/* MCI0 Power */
 }
 #endif
 
 int board_early_init_f(void)
 {
-	at91_periph_clk_enable(ATMEL_ID_PIOA);
-	at91_periph_clk_enable(ATMEL_ID_PIOB);
-	at91_periph_clk_enable(ATMEL_ID_PIOC);
-	at91_periph_clk_enable(ATMEL_ID_PIOD);
-	at91_periph_clk_enable(ATMEL_ID_PIOE);
-
 	at91_seriald_hw_init();
 
 	return 0;
@@ -98,10 +86,6 @@ int board_init(void)
 #ifdef CONFIG_GENERIC_ATMEL_MCI
 	sama5d3_xplained_mci0_hw_init();
 #endif
-#ifdef CONFIG_MACB
-	at91_gmac_hw_init();
-	at91_macb_hw_init();
-#endif
 	return 0;
 }
 
@@ -113,24 +97,6 @@ int dram_init(void)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-#ifdef CONFIG_MACB
-	macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
-	macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
-#endif
-	return 0;
-}
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
-{
-	atmel_mci_init((void *)ATMEL_BASE_MCI0);
-
-	return 0;
-}
-#endif
-
 /* SPL */
 #ifdef CONFIG_SPL_BUILD
 void spl_board_init(void)
-- 
2.11.0



More information about the U-Boot mailing list