[PATCH] net: pfe_eth: Use spi_flash_read API to access flash memory

Kuldeep Singh kuldeep.singh at nxp.com
Wed Dec 11 12:53:36 CET 2019


Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.

Signed-off-by: Kuldeep Singh <kuldeep.singh at nxp.com>
---
 drivers/net/pfe_eth/pfe_firmware.c | 44 +++++++++++++++++++++++++++++-
 include/configs/ls1012a_common.h   |  5 +++-
 2 files changed, 47 insertions(+), 2 deletions(-)

diff --git a/drivers/net/pfe_eth/pfe_firmware.c b/drivers/net/pfe_eth/pfe_firmware.c
index e4563f192b..61d1b96305 100644
--- a/drivers/net/pfe_eth/pfe_firmware.c
+++ b/drivers/net/pfe_eth/pfe_firmware.c
@@ -12,13 +12,14 @@
 
 #include <net/pfe_eth/pfe_eth.h>
 #include <net/pfe_eth/pfe_firmware.h>
+#include <spi_flash.h>
 #ifdef CONFIG_CHAIN_OF_TRUST
 #include <fsl_validate.h>
 #endif
 
 #define PFE_FIRMWARE_FIT_CNF_NAME	"config at 1"
 
-static const void *pfe_fit_addr = (void *)CONFIG_SYS_LS_PFE_FW_ADDR;
+static const void *pfe_fit_addr;
 
 /*
  * PFE elf firmware loader.
@@ -159,6 +160,43 @@ static int pfe_fit_check(void)
 	return ret;
 }
 
+int pfe_spi_flash_init(void)
+{
+	struct spi_flash *pfe_flash;
+	int ret = 0;
+	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
+
+#ifdef CONFIG_DM_SPI_FLASH
+	struct udevice *new;
+
+	/* speed and mode will be read from DT */
+	ret = spi_flash_probe_bus_cs(CONFIG_ENV_SPI_BUS,
+				     CONFIG_ENV_SPI_CS, 0, 0, &new);
+
+	pfe_flash = dev_get_uclass_priv(new);
+#else
+	pfe_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS,
+				    CONFIG_ENV_SPI_CS,
+				    CONFIG_ENV_SPI_MAX_HZ,
+				    CONFIG_ENV_SPI_MODE);
+#endif
+	if (!pfe_flash) {
+		printf("SF: probe for pfe ucode failed\n");
+	} else {
+		ret = spi_flash_read(pfe_flash,
+				     CONFIG_SYS_LS_PFE_FW_ADDR,
+				     CONFIG_SYS_QE_FMAN_FW_LENGTH,
+				     addr);
+		if (ret)
+			printf("SF: read for ucode failed\n");
+
+		pfe_fit_addr = addr;
+		spi_flash_free(pfe_flash);
+	}
+
+	return ret;
+}
+
 /*
  * PFE firmware initialization.
  * Loads different firmware files from FIT image.
@@ -183,6 +221,10 @@ int pfe_firmware_init(void)
 	int ret = 0;
 	int fw_count;
 
+	ret = pfe_spi_flash_init();
+	if (ret)
+		goto err;
+
 	ret = pfe_fit_check();
 	if (ret)
 		goto err;
diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h
index 2579e2fb37..cbc5bff21c 100644
--- a/include/configs/ls1012a_common.h
+++ b/include/configs/ls1012a_common.h
@@ -36,9 +36,12 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128 * 1024)
 
+/* PFE */
+#define CONFIG_SYS_FMAN_FW_ADDR		0x400d0000
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+
 /*SPI device */
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_TFABOOT)
-#define CONFIG_SYS_FMAN_FW_ADDR		0x400d0000
 #define CONFIG_SPI_FLASH_SPANSION
 #define CONFIG_FSL_SPI_INTERFACE
 #define CONFIG_SF_DATAFLASH
-- 
2.17.1



More information about the U-Boot mailing list