[PATCH v3 3/3] arm: mvebu: Initial ESPRESSOBin-Ultra board support

[Gérald Kerma]

Héllo,
> Message: 2
> Date: Fri, 13 Aug 2021 12:03:57 +0200
> From: Luka Kovacic<luka.kovacic at sartura.hr>
> To: Pali Roh?r<pali at kernel.org>
> Cc:u-boot at lists.denx.de, Robert Marko<robert.marko at sartura.hr>,
> 	Luka Perkov<luka.perkov at sartura.hr>, Marek Behun
> 	<marek.behun at nic.cz>,sr at denx.de,sjg at chromium.org,
> 	patrick.delaunay at foss.st.com,xypron.glpk at gmx.de
> Subject: Re: [PATCH v3 3/3] arm: mvebu: Initial ESPRESSOBin-Ultra
> 	board support
> Message-ID:
> 	<CADZsf3buKpgUJq_2yP1zakQbf0Hoq_4oPLdi69_d+qoR+Hbn0w at mail.gmail.com>
> Content-Type: text/plain; charset="UTF-8"
>
> Hello Pali,
>
> On Fri, Aug 13, 2021 at 11:27 AM Pali Roh?r<pali at kernel.org>  wrote:
>> On Friday 13 August 2021 01:39:38 Luka Kovacic wrote:
>>> Add initial support for the ESPRESSOBin-Ultra board from Globalscale
>>> Technologies, Inc.
>>>
>>> The board is based on the 64-bit dual-core Marvell Armada 3720 SoC.
>>> Peripherals:
>>>   - 5 Gigabit Ethernet ports (WAN has PoE, up to 30W, Topaz 6341 switch)
>>>   - RTC clock (PCF8563)
>>>   - USB 3.0 port
>>>   - USB 2.0 port
>>>   - 4x LED
>>>   - UART over Micro-USB
>>>   - M.2 slot (2280)
>>>   - Mini PCI-E slot
>>>
>>> Additionally, automatic import of the Marvell hw_info parameters is
>>> enabled via the recently added mac command for A37XX platforms.
>>> The parameters stored in Marvell hw_info are usually the board serial
>>> number and MAC addresses.
>>>
>>> Signed-off-by: Luka Kovacic<luka.kovacic at sartura.hr>
>>> Cc: Luka Perkov<luka.perkov at sartura.hr>
>>> Cc: Robert Marko<robert.marko at sartura.hr>
>>> ---
>>>   arch/arm/dts/Makefile                         |   1 +
>>>   .../arm/dts/armada-3720-espressobin-ultra.dts | 114 ++++++++++
>>>   arch/arm/dts/armada-3720-espressobin.dts      | 199 +----------------
>>>   arch/arm/dts/armada-3720-espressobin.dtsi     | 210 ++++++++++++++++++
>>>   board/Marvell/mvebu_armada-37xx/MAINTAINERS   |   8 +
>>>   board/Marvell/mvebu_armada-37xx/board.c       |  92 +++++++-
>>>   .../mvebu_espressobin-ultra-88f3720_defconfig |  93 ++++++++
>>>   7 files changed, 514 insertions(+), 203 deletions(-)
>>>   create mode 100644 arch/arm/dts/armada-3720-espressobin-ultra.dts
>>>   create mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
>>>   create mode 100644 configs/mvebu_espressobin-ultra-88f3720_defconfig
>> ...

Thanks, all, for this job.

I am available for testing (if needed) on EspressoBin V7, with eMMC, and 
EspressoBin Ultra.

I have issue on EspressoBin Ultra, with the v2 patch for 
EspressoBin-Ultra, on OpenWrt 21.02-RC, fw_printenv do not works... (CRC 
Error)
I have the same issue with the Marvell (GlobalScale) u-Boot, factory and 
upgraded version.

Environments variables are correctly managed from the u-Boot itself.

Regards,
Gérald Kerma

PS : I am only registered to the digest, so I hope my mail will not be 
disturbing...