<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2900.2180" name=GENERATOR></HEAD>
<BODY>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>Hello,
</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>I try to use a
ADS860 with a MPC850.</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>I compile u-boot,
dowload in flash and reset.</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>When reset, I see at
prompt this :</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial><FONT size=2><SPAN
class=797470913-30032005> </SPAN>Board: ADS rev PILOT<BR><SPAN
class=797470913-30032005> </SPAN>DRAM: 4M 60ns
DRAM: 4 MB<BR><SPAN class=797470913-30032005>
</SPAN>FLASH: 2 MB<BR></FONT></FONT><FONT face=Arial><FONT size=2><SPAN
class=797470913-30032005> </SPAN>In:
serial<BR><SPAN class=797470913-30032005>
</SPAN>Out: serial<BR><SPAN
class=797470913-30032005> </SPAN>Err:
serial<BR><SPAN class=797470913-30032005>
</SPAN>Net: SCC ETHERNET<BR><SPAN
class=797470913-30032005> </SPAN>PCMCIA:No card
present<BR><SPAN class=797470913-30032005> </SPAN>Hit any key
to stop autoboot: 0<BR><SPAN class=797470913-30032005>
</SPAN>## Booting image at fe080000 ...<BR><SPAN
class=797470913-30032005> </SPAN>Bad Magic
Number</FONT></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><SPAN class=797470913-30032005><FONT face=Arial size=2>After I set
configuration of IP service :</FONT></SPAN></DIV>
<DIV><SPAN class=797470913-30032005><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><FONT face=Arial size=2>=>setenv ethaddr 00:01:02:2A:3B:4A;setenv
serverip 172.17.21.30;setenv ipaddr 172.17.21.33;setenv gatewayip
172.17.0.1;setenv netmask 255.255.0.0;<BR></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>And I try to ping to
my host :</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN
class=797470913-30032005></SPAN></FONT> </DIV>
<DIV><FONT face=Arial size=2>=>ping 172.17.21.30<BR>Using SCC ETHERNET
device<BR>TX timeout<BR>TX not ready<BR>TX timeout<BR>ping failed; host
172.17.21.30 is not alive<BR>=></FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>Cable is tested, and
I'm sure </SPAN></FONT><FONT face=Arial size=2><SPAN
class=797470913-30032005>cable plugged into the right port because the led
of ETH-0 and LD10 is on and indicate good link integrity on th TP
port.</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>When ping, Ethernet
TX indicator blinks (LD6) is not active but Ethernet RX indicator blinks is
active when there are activity on networks ! I don't understand this
!</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN
class=797470913-30032005></SPAN></FONT> </DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>If you are a idea !
please !</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>Thank you for your
answer !</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN
class=797470913-30032005></SPAN></FONT> </DIV>
<DIV><FONT face=Arial size=2><SPAN class=797470913-30032005>David
Flament</SPAN></FONT></DIV>
<DIV><FONT face=Arial size=2><SPAN
class=797470913-30032005></SPAN></FONT> </DIV>
<DIV><FONT face=Arial size=2>--------------------------------</FONT></DIV>
<DIV><FONT face=Arial size=2>Flament David</FONT></DIV>
<DIV><FONT face=Arial size=2>d.flament@sofrel.com</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV></BODY></HTML>