[Test] [PATCH, v1, 2/4] udoo: Add ethernet support (FEC + Micrel KSZ9031).

Giuseppe Pagano giuseppe.pagano at seco.com
Mon Nov 11 15:58:25 CET 2013


Add Ethernet and networking support on uDoo board (FEC + phy Micrel KSZ9031).
---
 board/udoo/udoo.c      |  140 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/configs/udoo.h |   16 ++++++
 include/micrel.h       |    5 ++
 3 files changed, 161 insertions(+)

diff --git a/board/udoo/udoo.c b/board/udoo/udoo.c
index e9d6375..ca49ebb 100644
--- a/board/udoo/udoo.c
+++ b/board/udoo/udoo.c
@@ -9,6 +9,7 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/iomux.h>
+#include <malloc.h>
 #include <asm/arch/mx6-pins.h>
 #include <asm/errno.h>
 #include <asm/gpio.h>
@@ -18,6 +19,9 @@
 #include <asm/arch/crm_regs.h>
 #include <asm/io.h>
 #include <asm/arch/sys_proto.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -25,6 +29,9 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
 
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
 	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
@@ -58,6 +65,99 @@ static iomux_v3_cfg_t const wdog_pads[] = {
 	MX6_PAD_EIM_D19__GPIO_3_19,
 };
 
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	/* 
+	 * Bug: Apparently uDoo does not works with Gigabit switches...
+	 * Limiting speed to 10/100Mbps, and setting master mode, seems to 
+	 * be the only way to have a successfull PHY auto negotiation.
+	 * How to fix: Understand why Linux kernel do not have this issue.
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);
+
+        /* control data pad skew - devaddr = 0x02, register = 0x04 */
+        ksz9031_phy_extended_write(phydev, 0x02, 
+				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, 
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+        /* rx data pad skew - devaddr = 0x02, register = 0x05 */
+        ksz9031_phy_extended_write(phydev, 0x02, 
+				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+        /* tx data pad skew - devaddr = 0x02, register = 0x05 */
+        ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+        /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
+        ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+	return 0;
+}
+
+static iomux_v3_cfg_t const enet_pads1[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__ENET_RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__ENET_RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__ENET_RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__ENET_RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__ENET_RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__ENET_RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* RGMII reset */
+	MX6_PAD_EIM_D23__GPIO_3_23		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* alimentazione ethernet*/
+	MX6_PAD_EIM_EB3__GPIO_2_31		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 32 - 1 - (MODE0) all */
+	MX6_PAD_RGMII_RD0__GPIO_6_25		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 31 - 1 - (MODE1) all */
+	MX6_PAD_RGMII_RD1__GPIO_6_27		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 28 - 1 - (MODE2) all */
+	MX6_PAD_RGMII_RD2__GPIO_6_28		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 27 - 1 - (MODE3) all */
+	MX6_PAD_RGMII_RD3__GPIO_6_29		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
+	MX6_PAD_RGMII_RX_CTL__GPIO_6_24		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads2[] = {
+	MX6_PAD_RGMII_RD0__ENET_RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__ENET_RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__ENET_RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__ENET_RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+	udelay(20);
+	gpio_direction_output(IMX_GPIO_NR(2, 31), 1); /* Power on enet */
+
+	gpio_direction_output(IMX_GPIO_NR(3, 23), 0); /* assert PHY rst */
+
+	gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
+	udelay(1000);
+
+	gpio_set_value(IMX_GPIO_NR(3, 23), 1); /* deassert PHY rst */
+
+	/* Need delay 100ms to exit from reset. */
+	udelay(1000 * 100);
+
+	gpio_free(IMX_GPIO_NR(6, 24));
+	gpio_free(IMX_GPIO_NR(6, 25));
+	gpio_free(IMX_GPIO_NR(6, 27));
+	gpio_free(IMX_GPIO_NR(6, 28));
+	gpio_free(IMX_GPIO_NR(6, 29));
+
+	imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+}
+
 static void setup_iomux_uart(void)
 {
 	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
@@ -77,6 +177,37 @@ int board_mmc_getcd(struct mmc *mmc)
 	return 1; /* Always present */
 }
 
+int board_eth_init(bd_t *bis)
+{
+	uint32_t base = IMX_FEC_BASE;
+	struct mii_dev *bus = NULL;
+	struct phy_device *phydev = NULL;
+	int ret;
+
+	setup_iomux_enet();
+
+#ifdef CONFIG_FEC_MXC
+	bus = fec_get_miibus(base, -1);
+	if (!bus)
+		return 0;
+	/* scan phy 4,5,6,7 */
+	phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
+
+	if (!phydev) {
+		free(bus);
+		return 0;
+	}
+	printf("using phy at %d\n", phydev->addr);
+	ret  = fec_probe(bis, -1, base, bus, phydev);
+	if (ret) {
+		printf("FEC MXC: %s:failed\n", __func__);
+		free(phydev);
+		free(bus);
+	}
+#endif
+	return 0;
+}
+
 int board_mmc_init(bd_t *bis)
 {
 	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
@@ -94,6 +225,15 @@ int board_early_init_f(void)
 	return 0;
 }
 
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
 int board_init(void)
 {
 	/* address of boot parameters */
diff --git a/include/configs/udoo.h b/include/configs/udoo.h
index 78df071..b9a493c 100644
--- a/include/configs/udoo.h
+++ b/include/configs/udoo.h
@@ -34,6 +34,22 @@
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART2_BASE
 
+/* Network support */
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE                    ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE             RGMII
+#define CONFIG_ETHPRIME                 "FEC"
+#define CONFIG_FEC_MXC_PHYADDR          6
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9031
+
 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX		1
diff --git a/include/micrel.h b/include/micrel.h
index e1c62d8..1d72b50 100644
--- a/include/micrel.h
+++ b/include/micrel.h
@@ -15,6 +15,11 @@
 #define MII_KSZ9031_MOD_DATA_POST_INC_RW	0x8000
 #define MII_KSZ9031_MOD_DATA_POST_INC_W		0xC000
 
+#define MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW    0x4
+#define MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW     0x5
+#define MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW     0x6
+#define MII_KSZ9031_EXT_RGMII_CLOCK_SKEW       0x8
+
 struct phy_device;
 int ksz9021_phy_extended_write(struct phy_device *phydev, int regnum, u16 val);
 int ksz9021_phy_extended_read(struct phy_device *phydev, int regnum);
-- 
1.7.10.4



More information about the Test mailing list