[U-Boot-Users] Problems with u-boot, PPChameleonEVB and MontaVista kernel

[Chuck Meade]

You have a load address and entry point of 0x0.
You can't load and run Linux at 0x0.  Try something more sensible
like 0x400000.

Chuck

> -----Original Message-----
> From: u-boot-users-admin at lists.sourceforge.net
> [mailto:u-boot-users-admin at lists.sourceforge.net]On Behalf Of Andy
> Hawkins
> Sent: Tuesday, February 24, 2004 5:45 AM
> To: u-boot-users at lists.sourceforge.net
> Subject: [U-Boot-Users] Problems with u-boot, PPChameleonEVB and
> MontaVista kernel
>
>
> Hi all,
>
> I'm trying to get up and running with u-boot on a PPChameleonEVB,
> running the MontaVista kernel.
>
> I can successfully compile u-boot 1.0.0-pre and the kernel that came
> with the board (2.4.20 from the eldk), and boot the board
> successfully.
>
> However, when I try to compile the MontaVista kernel, the board will
> not boot. Their kernel doesn't directly support the PPChameleonEVB, so
> I'm using the one for the IBM 405EP eval (which the PPChameleon
> appears to be very similar to). I'm 'manually' running make pImage to
> build the kernel after the MontaVista targetconf tool has run the
> build, and booting from vmlinux.PPCBoot using tftp.
>
> I've been in touch with MontaVista, and they suggest re-building
> u-boot, but changing the definition of the bd_info struction (in
> include/asm-ppc/u-boot.h) to match that in the kernel. I've done this,
> but the boot still stops in the same place.
>
> I've compiled u-boot in debug mode, and this is what we see:
>
> reset
>
> U-Boot 1.0.0-pre (Feb 24 2004 - 10:11:24)
>
> CPU:   IBM PowerPC 405EP Rev. B at 133.333 MHz (PLB=133, OPB=66,
> EBC=33 MHz)
>        IIC Boot EEPROM disabled
>        PCI async ext clock used, internal PCI arbiter enabled
>        16 kB I-Cache 16 kB D-Cache
> Board: ### No HW ID - assuming PPChameleonEVB
> I2C:   ready
> DRAM:  32 MB
> Top of RAM usable for U-Boot at: 02000000
> Reserving 182k for U-Boot at: 01fd2000
> Reserving 257k for malloc() at: 01f91900
> Reserving 132 Bytes for Board Info at: 01f9187c
> Reserving 48 Bytes for Global Data at: 01f9184c
> Stack Pointer at: 01f91828
> New Stack Pointer is: 01f91828
> Now running in RAM - U-Boot at: 01fd2000
> FLASH:  4 MB
> U-Boot relocated to 01fd2000
> NAND:Probing at 0xff000000
>   32 MB
> ### main_loop entered: bootdelay=10
>
> ### main_loop: bootcmd="run nfsargs addip addcons;bootm
> $(kernel_addr)"
> Hit any key to stop autoboot: 10  0
> => run net_selc f
>
> ENET Speed is 10 Mbps - HALF duplex connection
> TFTP from server 191.53.51.21; our IP address is 191.53.51.200
> Filename 'vmlinux.PPCBoot'.
> Load address: 0x200000
> Loading:
>
> [snip tftp progress]
>
> done
> Bytes transferred = 629509 (99b05 hex)
> ## Booting image at 00200000 ...
>    Image Name:   Linux-2.4.18_mvl30-405ep_eval
>    Created:      2004-02-24  10:18:07 UTC
>    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
>    Data Size:    629445 Bytes = 614.7 kB
>    Load Address: 00000000
>    Entry Point:  00000000
>    Verifying Checksum ... OK
>    Uncompressing Kernel Image ... OK
> ## Current stack ends at 0x01F911D8 => set upper limit to 0x00800000
> ## cmdline at 0x007FFF00 ... 0x007FFF70
> bd address  = 0x01F9187C
> memstart    = 0x00000000
> memsize     = 0x02000000
> flashstart  = 0xFFFC0000
> flashsize   = 0x00400000
> flashoffset = 0x00029B00
> sramstart   = 0x00000000
> sramsize    = 0x00000000
> bootflags   = 0x0000A000
> procfreq    = 133.333 MHz
> plb_busfreq = 133.333 MHz
> pci_busfreq = 33.333 MHz
> ethaddr     = 00:50:C2:1E:AF:FE
> eth1addr    = 00:50:C2:1E:AF:FD
> IP addr     = 191.53.51.200
> baudrate    = 115200 bps
> ## Loading RAMDisk Image at ffd00000 ...
>    Image Name:   Simple Embedded Linux Framework
>    Created:      2002-10-24   9:30:38 UTC
>    Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
>    Data Size:    1476478 Bytes =  1.4 MB
>    Load Address: 00000000
>    Entry Point:  00000000
>    Verifying Checksum ... OK
> ## initrd at 0xFFD00040 ... 0xFFE687BD (len=1476478=0x16877E)
>    Loading Ramdisk to 01e28000, end 01f9077e ... OK
> ## Transferring control to Linux (at address 00000000) ...
>
> I do have access to a BDI2000, that I've used to break into a running
> kernel (at start_here), but can't get it to break when I use the
> MontaVista kernel. From this, I assume that it's failing somewhere
> very early in the linux boot process.
>
> Can anyone offer any advice?
>
> Many thanks.
>
> Andy
>
>
>
> -------------------------------------------------------
> SF.Net is sponsored by: Speed Start Your Linux Apps Now.
> Build and deploy apps & Web services for Linux with
> a free DVD software kit from IBM. Click Now!
> http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users