[U-Boot-Users] [DNX#2006081142000054] [PATCH 04/07 v2]: tsi108 on chip Ethernet support

[DENX Support System]

Hello list,

inside the automatic U-Boot patch tracking system a new ticket
[DNX#2006081142000054] was created:

<snip>
> Tundra tsi108 on chip Ethernet controller support.
> There are two Gitb Ethernet ports on tsi108 chip.
> 
> Signed-off-by: Alexandre Bounine <alexandreb at tundra.com>
> Signed-off-by: Roy Zang	<tie-fei.zang at freescale.com>
>  
> ---
>  drivers/tsi108_eth.c | 1042
> ++++++++++++++++++++++++++++++++++++++++++++++++++
>  net/eth.c            |    4 
>  2 files changed, 1046 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/tsi108_eth.c b/drivers/tsi108_eth.c
> new file mode 100644
> index 0000000..196c4b4
> --- /dev/null
> +++ b/drivers/tsi108_eth.c
> @@ -0,0 +1,1042 @@
> +/**********************************************************************
> *
> + *
> + * Copyright (c) 2005 Freescale Semiconductor, Inc.
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + *
> + * Description:
> + *   Ethernet interface for Tundra TSI108 bridge chip
> + *
> +
> ***********************************************************************/
> +
> +#include <common.h>
> +
> +#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) \
> +	&& defined(CONFIG_TSI108_ETH)
> +
> +#if !defined(CONFIG_TSI108_ETH_NUM_PORTS) ||
> (CONFIG_TSI108_ETH_NUM_PORTS > 2)
> +#error "CONFIG_TSI108_ETH_NUM_PORTS must be defined as 1 or 2"
> +#endif
> +
> +#include <malloc.h>
> +#include <net.h>
> +#include <asm/cache.h>
> +
> +#ifdef DEBUG
> +#define TSI108_ETH_DEBUG 7
> +#else
> +#define TSI108_ETH_DEBUG 0
> +#endif
> +
> +#if TSI108_ETH_DEBUG > 0
> +#define debug_lev(lev, fmt, args...) if (lev <= TSI108_ETH_DEBUG)
> printf("%s %d: " fmt, __FUNCTION__, __LINE__, ##args)
> +#else
> +#define debug_lev(lev, fmt, args...) do{}while(0)
> +#endif
> +
> +#define RX_PRINT_ERRORS
> +#define TX_PRINT_ERRORS
> +
> +#define ETH_BASE  (CFG_TSI108_CSR_BASE + 0x6000)
> +
> +#define ETH_PORT_OFFSET  0x400
> +
> +#define __REG32(base, offset) (*((volatile u32 *)((char *)(base) +
> (offset))))
> +
> +#define reg_MAC_CONFIG_1(base)                 __REG32(base,
> 0x00000000)
> +#define MAC_CONFIG_1_TX_ENABLE               (0x00000001)
> +#define MAC_CONFIG_1_SYNC_TX_ENABLE          (0x00000002)
> +#define MAC_CONFIG_1_RX_ENABLE               (0x00000004)
> +#define MAC_CONFIG_1_SYNC_RX_ENABLE          (0x00000008)
> +#define MAC_CONFIG_1_TX_FLOW_CONTROL         (0x00000010)
> +#define MAC_CONFIG_1_RX_FLOW_CONTROL         (0x00000020)
> +#define MAC_CONFIG_1_LOOP_BACK               (0x00000100)
> +#define MAC_CONFIG_1_RESET_TX_FUNCTION       (0x00010000)
> +#define MAC_CONFIG_1_RESET_RX_FUNCTION       (0x00020000)
> +#define MAC_CONFIG_1_RESET_TX_MAC            (0x00040000)
> +#define MAC_CONFIG_1_RESET_RX_MAC            (0x00080000)
> +#define MAC_CONFIG_1_SIM_RESET               (0x40000000)
> +#define MAC_CONFIG_1_SOFT_RESET              (0x80000000)
> +
</snip>

Your U-Boot support team