[U-Boot-Users] PPC440EPx: Make Sequoia boot vxWorks

[Niklaus Giger]

vxWorks expects in 
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash
Therefore I reordered the TLB entries correspondingly and did set the
CFG_TLB_FOR_BOOT_FLASH  to 3 (see my previous patch about minimal
support for vxWorks)

After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from 
June 18, 2007)

If Stefan agrees with this patch, I will submit a similar for the yosemite
board.

Signed-off-by: Niklaus Giger <niklaus.giger at netstal.com>
---
 board/amcc/sequoia/init.S |   20 ++++++++++----------
 include/configs/sequoia.h |    1 +
 2 files changed, 11 insertions(+), 10 deletions(-)

diff --git a/board/amcc/sequoia/init.S b/board/amcc/sequoia/init.S
index 5fe3af9..21ee9f5 100644
--- a/board/amcc/sequoia/init.S
+++ b/board/amcc/sequoia/init.S
@@ -87,19 +87,22 @@
 tlbtab:
 	tlbtab_start
 
-	/*
-	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
-	 * speed up boot process. It is patched after relocation to enable SA_I
-	 */
+	/* vxWorks needs this as first entry for the Machine Check interrupt */
+	tlbentry( 0x40000000, SZ_256M, 0, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB-entry for DDR SDRAM (Up to 2GB) */
+	tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* TLB-entry for EBC */
+	tlbentry( CFG_BCSR_BASE, SZ_256M, CFG_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
+
+	/* BOOT_CS (FLASH) must be forth. Before relocation SA_I can be off to use the */
 #ifndef CONFIG_NAND_SPL
 	tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G )
 #else
 	tlbentry( CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 1, AC_R|AC_W|AC_X|SA_G )
 #endif
 
-	/* TLB-entry for DDR SDRAM (Up to 2GB) */
-	tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
-
 #ifdef CFG_INIT_RAM_DCACHE
 	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
 	tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
@@ -111,9 +114,6 @@ tlbtab:
 	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I )
 	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I )
 
-	/* TLB-entry for EBC */
-	tlbentry( CFG_BCSR_BASE, SZ_1K, CFG_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
-
 	/* TLB-entry for NAND */
 	tlbentry( CFG_NAND_ADDR, SZ_1K, CFG_NAND_ADDR, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
 
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 600f98c..6a972e4 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -53,6 +53,7 @@
 #define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
 #define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
 
+#define CFG_TLB_FOR_BOOT_FLASH  3
 #define CFG_BOOT_BASE_ADDR	0xf0000000
 #define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-- 
1.5.2