[U-Boot-Users] [PATCH] mpc83xx: add support for the MPC8360E-RDK

Anton Vorontsov avorontsov at ru.mvista.com
Tue Dec 25 18:01:23 CET 2007


This is MPC8360E based board with:
- 256MB fixed SDRAM, 8MB NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
  BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
  DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
  connected to SPI.

Features not supported in this patch are:
- LBC configuration for the graphics controller;
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.

Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
---
 Makefile                        |   11 +
 board/mpc8360erdk/Makefile      |   50 ++++
 board/mpc8360erdk/config.mk     |   28 ++
 board/mpc8360erdk/mpc8360erdk.c |  316 ++++++++++++++++++++++
 board/mpc8360erdk/nand.c        |  201 ++++++++++++++
 include/configs/MPC8360ERDK.h   |  559 +++++++++++++++++++++++++++++++++++++++
 6 files changed, 1165 insertions(+), 0 deletions(-)
 create mode 100644 board/mpc8360erdk/Makefile
 create mode 100644 board/mpc8360erdk/config.mk
 create mode 100644 board/mpc8360erdk/mpc8360erdk.c
 create mode 100644 board/mpc8360erdk/nand.c
 create mode 100644 include/configs/MPC8360ERDK.h

diff --git a/Makefile b/Makefile
index edba1ae..b0895fe 100644
--- a/Makefile
+++ b/Makefile
@@ -1909,6 +1909,17 @@ MPC837XEMDS_HOST_config:	unconfig
 	fi ;
 	@$(MKCONFIG) -a MPC837XEMDS ppc mpc83xx mpc837xemds freescale
 
+MPC8360ERDK_33MHZ_config \
+MPC8360ERDK_66MHZ_config \
+MPC8360ERDK_config:
+	@mkdir -p $(obj)include
+	@echo "" >$(obj)include/config.h ; \
+	if [ "$(findstring _33MHZ_,$@)" ] ; then \
+		echo -n "... CLKIN 33MHz " ; \
+		echo "#define CONFIG_CLKIN_33MHZ" >>$(obj)include/config.h ;\
+	fi ;
+	@$(MKCONFIG) -a MPC8360ERDK ppc mpc83xx mpc8360erdk
+
 sbc8349_config:		unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
 
diff --git a/board/mpc8360erdk/Makefile b/board/mpc8360erdk/Makefile
new file mode 100644
index 0000000..97ae11d
--- /dev/null
+++ b/board/mpc8360erdk/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= $(BOARD).o nand.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/mpc8360erdk/config.mk b/board/mpc8360erdk/config.mk
new file mode 100644
index 0000000..87dd746
--- /dev/null
+++ b/board/mpc8360erdk/config.mk
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# MPC8360ERDK
+#
+
+TEXT_BASE = 0xFF800000
diff --git a/board/mpc8360erdk/mpc8360erdk.c b/board/mpc8360erdk/mpc8360erdk.c
new file mode 100644
index 0000000..51cf89f
--- /dev/null
+++ b/board/mpc8360erdk/mpc8360erdk.c
@@ -0,0 +1,316 @@
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu at freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb at logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov at ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc83xx.h>
+#include <i2c.h>
+#include <spd.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <pci.h>
+#include <libfdt.h>
+
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+	/* MDIO */
+	{0,  1, 3, 0, 2}, /* MDIO */
+	{0,  2, 1, 0, 1}, /* MDC */
+
+	/* GETH1 */
+	{0,  3, 1, 0, 1}, /* TxD0 */
+	{0,  4, 1, 0, 1}, /* TxD1 */
+	{0,  5, 1, 0, 1}, /* TxD2 */
+	{0,  6, 1, 0, 1}, /* TxD3 */
+	{0,  9, 2, 0, 1}, /* RxD0 */
+	{0, 10, 2, 0, 1}, /* RxD1 */
+	{0, 11, 2, 0, 1}, /* RxD2 */
+	{0, 12, 2, 0, 1}, /* RxD3 */
+	{0,  7, 1, 0, 1}, /* TX_EN */
+	{0,  8, 1, 0, 1}, /* TX_ER */
+	{0, 15, 2, 0, 1}, /* RX_DV */
+	{0, 16, 2, 0, 1}, /* RX_ER */
+	{0,  0, 2, 0, 1}, /* RX_CLK */
+	{2,  9, 1, 0, 3}, /* GTX_CLK - CLK10 */
+	{2,  8, 2, 0, 1}, /* GTX125 - CLK9 */
+
+	/* GETH2 */
+	{0, 17, 1, 0, 1}, /* TxD0 */
+	{0, 18, 1, 0, 1}, /* TxD1 */
+	{0, 19, 1, 0, 1}, /* TxD2 */
+	{0, 20, 1, 0, 1}, /* TxD3 */
+	{0, 23, 2, 0, 1}, /* RxD0 */
+	{0, 24, 2, 0, 1}, /* RxD1 */
+	{0, 25, 2, 0, 1}, /* RxD2 */
+	{0, 26, 2, 0, 1}, /* RxD3 */
+	{0, 21, 1, 0, 1}, /* TX_EN */
+	{0, 22, 1, 0, 1}, /* TX_ER */
+	{0, 29, 2, 0, 1}, /* RX_DV */
+	{0, 30, 2, 0, 1}, /* RX_ER */
+	{0, 31, 2, 0, 1}, /* RX_CLK */
+	{2,  2, 1, 0, 2}, /* GTX_CLK - CLK10 */
+	{2,  3, 2, 0, 1}, /* GTX125 - CLK4 */
+
+	/* GETH3 */
+	{4,  0, 1, 0, 1}, /* TxD0 */
+	{4,  1, 1, 0, 1}, /* TxD1 */
+	{4,  2, 1, 0, 1}, /* TxD2 */
+	{4,  3, 1, 0, 1}, /* TxD3 */
+	{4,  6, 2, 0, 1}, /* RxD0 */
+	{4,  7, 2, 0, 1}, /* RxD1 */
+	{4,  8, 2, 0, 1}, /* RxD2 */
+	{4,  9, 2, 0, 1}, /* RxD3 */
+	{4,  4, 1, 0, 1}, /* TX_EN */
+	{4,  5, 1, 0, 1}, /* TX_ER */
+	{4, 12, 2, 0, 1}, /* RX_DV */
+	{4, 13, 2, 0, 1}, /* RX_ER */
+	{4, 10, 2, 0, 1}, /* COL */
+	{4, 11, 2, 0, 1}, /* CRS */
+	{2, 18, 2, 0, 1}, /* TX_CLK - CLK19 */
+	{2, 19, 2, 0, 1}, /* RX_CLK - CLK20 */
+
+	/* GETH4 */
+	{1, 14, 1, 0, 1}, /* TxD0 */
+	{1, 15, 1, 0, 1}, /* TxD1 */
+	{1, 16, 1, 0, 1}, /* TxD2 */
+	{1, 17, 1, 0, 1}, /* TxD3 */
+	{1, 20, 2, 0, 1}, /* RxD0 */
+	{1, 21, 2, 0, 1}, /* RxD1 */
+	{1, 22, 2, 0, 1}, /* RxD2 */
+	{1, 23, 2, 0, 1}, /* RxD3 */
+	{1, 18, 1, 0, 1}, /* TX_EN */
+	{1, 19, 1, 0, 2}, /* TX_ER */
+	{1, 26, 2, 0, 1}, /* RX_DV */
+	{1, 27, 2, 0, 1}, /* RX_ER */
+	{1, 24, 2, 0, 1}, /* COL */
+	{1, 25, 2, 0, 1}, /* CRS */
+	{2,  6, 2, 0, 1}, /* TX_CLK - CLK7 */
+	{2,  7, 2, 0, 1}, /* RX_CLK - CLK8 */
+
+	/* PCI */
+	{5,  4, 2, 0, 3}, /* PCI_M66EN */
+	{5,  5, 1, 0, 3}, /* PCI_INTA */
+	{5,  6, 1, 0, 3}, /* PCI_RSTO */
+	{5,  7, 3, 0, 3}, /* PCI_C_BE0 */
+	{5,  8, 3, 0, 3}, /* PCI_C_BE1 */
+	{5,  9, 3, 0, 3}, /* PCI_C_BE2 */
+	{5, 10, 3, 0, 3}, /* PCI_C_BE3 */
+	{5, 11, 3, 0, 3}, /* PCI_PAR */
+	{5, 12, 3, 0, 3}, /* PCI_FRAME */
+	{5, 13, 3, 0, 3}, /* PCI_TRDY */
+	{5, 14, 3, 0, 3}, /* PCI_IRDY */
+	{5, 15, 3, 0, 3}, /* PCI_STOP */
+	{5, 16, 3, 0, 3}, /* PCI_DEVSEL */
+	{5, 17, 0, 0, 0}, /* PCI_IDSEL */
+	{5, 18, 3, 0, 3}, /* PCI_SERR */
+	{5, 19, 3, 0, 3}, /* PCI_PERR */
+	{5, 20, 3, 0, 3}, /* PCI_REQ0 */
+	{5, 21, 2, 0, 3}, /* PCI_REQ1 */
+	{5, 22, 2, 0, 3}, /* PCI_GNT2 */
+	{5, 23, 3, 0, 3}, /* PCI_GNT0 */
+	{5, 24, 1, 0, 3}, /* PCI_GNT1 */
+	{5, 25, 1, 0, 3}, /* PCI_GNT2 */
+	{5, 26, 0, 0, 0}, /* PCI_CLK0 */
+	{5, 27, 0, 0, 0}, /* PCI_CLK1 */
+	{5, 28, 0, 0, 0}, /* PCI_CLK2 */
+	{5, 29, 0, 0, 3}, /* PCI_SYNC_OUT */
+	{6,  0, 3, 0, 3}, /* PCI_AD0 */
+	{6,  1, 3, 0, 3}, /* PCI_AD1 */
+	{6,  2, 3, 0, 3}, /* PCI_AD2 */
+	{6,  3, 3, 0, 3}, /* PCI_AD3 */
+	{6,  4, 3, 0, 3}, /* PCI_AD4 */
+	{6,  5, 3, 0, 3}, /* PCI_AD5 */
+	{6,  6, 3, 0, 3}, /* PCI_AD6 */
+	{6,  7, 3, 0, 3}, /* PCI_AD7 */
+	{6,  8, 3, 0, 3}, /* PCI_AD8 */
+	{6,  9, 3, 0, 3}, /* PCI_AD9 */
+	{6, 10, 3, 0, 3}, /* PCI_AD10 */
+	{6, 11, 3, 0, 3}, /* PCI_AD11 */
+	{6, 12, 3, 0, 3}, /* PCI_AD12 */
+	{6, 13, 3, 0, 3}, /* PCI_AD13 */
+	{6, 14, 3, 0, 3}, /* PCI_AD14 */
+	{6, 15, 3, 0, 3}, /* PCI_AD15 */
+	{6, 16, 3, 0, 3}, /* PCI_AD16 */
+	{6, 17, 3, 0, 3}, /* PCI_AD17 */
+	{6, 18, 3, 0, 3}, /* PCI_AD18 */
+	{6, 19, 3, 0, 3}, /* PCI_AD19 */
+	{6, 20, 3, 0, 3}, /* PCI_AD20 */
+	{6, 21, 3, 0, 3}, /* PCI_AD21 */
+	{6, 22, 3, 0, 3}, /* PCI_AD22 */
+	{6, 23, 3, 0, 3}, /* PCI_AD23 */
+	{6, 24, 3, 0, 3}, /* PCI_AD24 */
+	{6, 25, 3, 0, 3}, /* PCI_AD25 */
+	{6, 26, 3, 0, 3}, /* PCI_AD26 */
+	{6, 27, 3, 0, 3}, /* PCI_AD27 */
+	{6, 28, 3, 0, 3}, /* PCI_AD28 */
+	{6, 29, 3, 0, 3}, /* PCI_AD29 */
+	{6, 30, 3, 0, 3}, /* PCI_AD30 */
+	{6, 31, 3, 0, 3}, /* PCI_AD31 */
+
+	/* NAND */
+	{4, 18, 2, 0, 0}, /* NAND_RYnBY */
+
+	/* END of table */
+	{0,  0, 0, 0, QE_IOP_TAB_END},
+};
+
+int board_early_init_f(void)
+{
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	void *reg = (void *)(CFG_IMMR + 0x14a8);
+	u32 val;
+
+	/*
+	 * Because of errata in the UCCs, we have to write to the reserved
+	 * registers to slow the clocks down.
+	 */
+	val = in_be32(reg);
+	/* UCC1 */
+	val |= 0x00003000;
+	/* UCC2 */
+	val |= 0x0c000000;
+	out_be32(reg, val);
+
+	return 0;
+}
+
+int fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *)CFG_IMMR;
+	u32 msize = 0;
+	u32 ddr_size;
+	u32 ddr_size_log2;
+
+	msize = CFG_DDR_SIZE;
+	for (ddr_size = msize << 20, ddr_size_log2 = 0;
+	     (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) {
+		if (ddr_size & 1)
+			return -1;
+	}
+
+	im->sysconf.ddrlaw[0].ar =
+	    LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
+
+	im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS;
+	im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG;
+	im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
+	im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+	im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+	im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
+	im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG;
+	im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2;
+	im->ddr.sdram_mode = CFG_DDR_MODE;
+	im->ddr.sdram_mode2 = CFG_DDR_MODE2;
+	im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+	im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL;
+	udelay(200);
+	im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+
+	return msize;
+}
+
+long int initdram(int board_type)
+{
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+	extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+	volatile immap_t *im = (immap_t *)CFG_IMMR;
+	u32 msize = 0;
+
+	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR;
+	msize = fixed_sdram();
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+	/*
+	 * Initialize DDR ECC byte
+	 */
+	ddr_enable_ecc(msize * 1024 * 1024);
+#endif
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+int checkboard(void)
+{
+	puts("Board: Freescale/Logic MPC8360ERDK\n");
+	return 0;
+}
+
+static struct pci_region pci_regions[] = {
+	{
+		.bus_start = CFG_PCI1_MEM_BASE,
+		.phys_start = CFG_PCI1_MEM_PHYS,
+		.size = CFG_PCI1_MEM_SIZE,
+		.flags = PCI_REGION_MEM | PCI_REGION_PREFETCH,
+	},
+	{
+		.bus_start = CFG_PCI1_MMIO_BASE,
+		.phys_start = CFG_PCI1_MMIO_PHYS,
+		.size = CFG_PCI1_MMIO_SIZE,
+		.flags = PCI_REGION_MEM,
+	},
+	{
+		.bus_start = CFG_PCI1_IO_BASE,
+		.phys_start = CFG_PCI1_IO_PHYS,
+		.size = CFG_PCI1_IO_SIZE,
+		.flags = PCI_REGION_IO,
+	},
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions, };
+
+#if defined(PCI_33M)
+	clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 |
+		    OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR;
+	printf("PCI clock is 33MHz\n");
+#else
+	clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2;
+	printf("PCI clock is 66MHz\n");
+#endif
+
+	udelay(2000);
+
+	/* Configure PCI Local Access Windows */
+	pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+	pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+	mpc83xx_pci_init(1, reg, 0);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+	ft_pci_setup(blob, bd);
+}
+#endif
diff --git a/board/mpc8360erdk/nand.c b/board/mpc8360erdk/nand.c
new file mode 100644
index 0000000..b9495f9
--- /dev/null
+++ b/board/mpc8360erdk/nand.c
@@ -0,0 +1,201 @@
+/*
+ * FSL UPM NAND driver
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov at ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <config.h>
+
+#if defined(CONFIG_CMD_NAND)
+#include <common.h>
+#include <asm/io.h>
+#include <asm/immap_83xx.h>
+#include <asm/errno.h>
+#include <linux/mtd/mtd.h>
+#include <nand.h>
+
+static u32 upm_table[] = {
+	0x0ff03c30, 0x0ff03c30, 0x0ff03c34, 0x0ff33c30, /* Words  0 to  3 */
+	0xfff33c31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words  4 to  7 */
+	0x0faf3c30, 0x0faf3c30, 0x0faf3c30, 0x0fff3c34, /* Words  8 to 11 */
+	0xffff3c31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words 12 to 15 */
+	0x0fa3fc30, 0x0fa3fc30, 0x0fa3fc30, 0x0ff3fc34, /* Words 16 to 19 */
+	0xfff3fc31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words 20 to 23 */
+	0x0ff33c30, 0x0fa33c30, 0x0fa33c34, 0x0ff33c30, /* Words 24 to 27 */
+	0xfff33c31, 0xfff0fc30, 0xfff0fc30, 0xfff0fc30, /* Words 28 to 31 */
+	0xfff3fc30, 0xfff3fc30, 0xfff6fc30, 0xfffcfc30, /* Words 32 to 35 */
+	0xfffcfc30, 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, /* Words 36 to 39 */
+	0xfffcfc30, 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, /* Words 40 to 43 */
+	0xfffdfc30, 0xfffffc30, 0xfffffc30, 0xfffffc31, /* Words 44 to 47 */
+	0xfffffc30, 0xfffffc00, 0xfffffc00, 0xfffffc00, /* Words 48 to 51 */
+	0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, /* Words 52 to 55 */
+	0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, /* Words 56 to 59 */
+	0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, /* Words 60 to 63 */
+};
+
+static struct immap *im = (struct immap *)CFG_IMMR;
+static u8 *fl = (u8 *)CFG_NAND_BASE;
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+	if (in_be32(&im->qepio.ioport[4].pdat) & 0x00002000) {
+		debug("nand ready\n");
+		return 1;
+	}
+
+	debug("nand busy\n");
+	return 0;
+}
+
+void run_pattern(u32 cmd, u32 pat_offset)
+{
+	out_be32(&im->lbus.mamr, 0x30000000 | pat_offset);
+	out_be32(&im->lbus.mar, cmd << 24);
+	out_8(fl, 0x0);
+
+	/*
+	 * Hm, MPC8360E-RDK needs this. Probably weird chip, because I don't
+	 * see any need for this on MPC8555E + Samsung K9F1G08U0A.
+	 * Usually here are 0-2 unexpected busy states per block read.
+	 */
+	while (!nand_dev_ready(NULL))
+		debug("unexpected busy state\n");
+
+	out_be32(&im->lbus.mamr, 0x0);
+
+	while (in_be32(&im->lbus.mamr) != 0x0)
+		eieio();
+}
+
+void setup_upm(void)
+{
+	int i;
+
+	/* MAMR: OP bit */
+	out_be32(&im->lbus.mamr, 0x10000000);
+
+	for (i = 0; i < 64; i++) {
+		out_be32(&im->lbus.mdr, upm_table[i]);
+		debug("%x\n", in_be32(&im->im_lbc.mdr));
+		out_8(fl, 0x0);
+		debug("%x\n", in_be32(&im->im_lbc.mamr));
+	}
+
+	/* MAMR: normal mode */
+	out_be32(&im->lbus.mamr, 0x00000000);
+
+	while (in_be32(&im->lbus.mamr) != 0x0)
+		eieio();
+}
+
+static void nand_cmdfunc(struct mtd_info *mtd, unsigned command, int column,
+			 int page_addr)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	if (command == NAND_CMD_SEQIN) {
+		int readcmd;
+
+		if (column >= mtd->oobblock) {
+			/* OOB area */
+			column -= mtd->oobblock;
+			readcmd = NAND_CMD_READOOB;
+		} else if (column < 256) {
+			/* First 256 bytes --> READ0 */
+			readcmd = NAND_CMD_READ0;
+		} else {
+			column -= 256;
+			readcmd = NAND_CMD_READ1;
+		}
+		run_pattern(readcmd, 8);
+	}
+
+	run_pattern(command, 8);
+
+	if (column != -1)
+		run_pattern(column, 16);
+
+	if (page_addr != -1) {
+		run_pattern(page_addr, 16);
+		run_pattern((page_addr >> 8) & 0xFF, 16);
+		if (chip->chipsize > (32 << 20))
+			run_pattern((page_addr >> 16) & 0x0f, 16);
+	}
+
+	while (!chip->dev_ready(mtd))
+		continue;
+}
+
+static void nand_write_byte(struct mtd_info *mtd, u_char byte)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	out_8(chip->IO_ADDR_W, byte);
+}
+
+static u8 nand_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	return in_8(chip->IO_ADDR_R);
+}
+
+static void nand_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+	int i;
+	struct nand_chip *chip = mtd->priv;
+
+	for (i = 0; i < len; i++)
+		chip->write_byte(mtd, buf[i]);
+}
+
+static void nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
+{
+	int i;
+	struct nand_chip *chip = mtd->priv;
+
+	for (i = 0; i < len; i++)
+		buf[i] = in_8(chip->IO_ADDR_R);
+}
+
+static int nand_verify_buf(struct mtd_info *mtd, const u_char *buf, int len)
+{
+	int i;
+	struct nand_chip *chip = mtd->priv;
+
+	for (i = 0; i < len; i++) {
+		if (buf[i] != in_8(chip->IO_ADDR_R))
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
+static void nand_hwcontrol(struct mtd_info *mtd, int cmd)
+{
+}
+
+int board_nand_init(struct nand_chip *nand)
+{
+	setup_upm();
+
+	nand->chip_delay = 50;
+	nand->eccmode = NAND_ECC_SOFT;
+	nand->hwcontrol = nand_hwcontrol;
+	nand->cmdfunc = nand_cmdfunc;
+	nand->read_byte = nand_read_byte;
+	nand->write_byte = nand_write_byte;
+	nand->read_buf = nand_read_buf;
+	nand->write_buf = nand_write_buf;
+	nand->verify_buf = nand_verify_buf;
+	nand->dev_ready = nand_dev_ready;
+
+	return 0;
+}
+#endif /* CONFIG_CMD_NAND */
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h
new file mode 100644
index 0000000..195c7a8
--- /dev/null
+++ b/include/configs/MPC8360ERDK.h
@@ -0,0 +1,559 @@
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu at freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb at logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov at ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1 /* E300 family */
+#define CONFIG_QE		1 /* Has QE */
+#define CONFIG_MPC83XX		1 /* MPC83XX family */
+#define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
+#define CONFIG_MPC8360ERDK	1 /* MPC8360ERDK board specific */
+
+/*
+ * System Clock Setup
+ */
+#ifdef CONFIG_CLKIN_33MHZ
+#define CONFIG_83XX_CLKIN		33000000
+#define CONFIG_SYS_CLK_FREQ		33000000
+#define PCI_33M				1
+#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK	HRCWL_CSB_TO_CLKIN_10X1
+#else
+#define CONFIG_83XX_CLKIN		66000000
+#define CONFIG_SYS_CLK_FREQ		66000000
+#define PCI_66M				1
+#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK	HRCWL_CSB_TO_CLKIN_5X1
+#endif /* CONFIG_CLKIN_33MHZ */
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CFG_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_1X1 |\
+	HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
+	HRCWL_CORE_TO_CSB_2X1 |\
+	HRCWL_CE_TO_PLL_1X15)
+
+#define CFG_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_PCICKDRV_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_SECONDARY_DDR_DISABLE |\
+	HRCWH_BIG_ENDIAN |\
+	HRCWH_LALE_EARLY)
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRH		0x00000000
+#define CFG_SICRL		0x40000000
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR		0xE0000000
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE		0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE		CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
+#define CFG_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+
+#define CFG_83XX_DDR_USES_CS0
+
+#undef CONFIG_DDR_ECC		/* support DDR ECC function */
+#undef CONFIG_DDR_ECC_CMD	/* Use DDR ECC user commands */
+
+/*
+ * DDRCDR - DDR Control Driver Register
+ */
+#define CFG_DDRCDR_VALUE	0x80080001
+
+#undef CONFIG_SPD_EEPROM	/* Do not use SPD EEPROM for DDR setup */
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CONFIG_DDR_II
+#define CFG_DDR_SIZE		256 /* MB */
+#define CFG_DDRCDR		0x80080001
+#define CFG_DDR_CS0_BNDS	0x0000000f
+#define CFG_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \
+				 CSCONFIG_COL_BIT_10)
+#define CFG_DDR_TIMING_0	0x00330903
+#define CFG_DDR_TIMING_1	0x3835a322
+#define CFG_DDR_TIMING_2	0x00104909
+#define CFG_DDR_TIMING_3	0x00000000
+#define CFG_DDR_CLK_CNTL	0x02000000
+#define CFG_DDR_MODE		0x47800432
+#define CFG_DDR_MODE2		0x8000c000
+#define CFG_DDR_INTERVAL	0x045b0100
+#define CFG_DDR_SDRAM_CFG	0x03000000
+#define CFG_DDR_SDRAM_CFG2	0x00001000
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST		/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00000000 /* memtest region */
+#define CFG_MEMTEST_END		0x00100000
+
+/*
+ * The reserved memory
+ */
+#define CFG_MONITOR_BASE	TEXT_BASE /* start of monitor */
+#define CFG_FLASH_BASE		0xFF800000 /* FLASH base address */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef	CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END	0x1000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE	0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_4)
+#define CFG_LBC_LBCR		0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI		/* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER	/* use the CFI driver */
+#define CFG_FLASH_SIZE		8 /* max FLASH size is 32M */
+#define CFG_FLASH_PROTECTION	1 /* Use intel Flash protection. */
+
+#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM	0x80000018 /* 32MB window size */
+
+#define CFG_BR0_PRELIM	(CFG_FLASH_BASE | /* Flash Base address */ \
+			(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+			BR_V)	/* valid */
+#define CFG_OR0_PRELIM		((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+				OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \
+				OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+				OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+
+#define CFG_MAX_FLASH_BANKS	1 /* number of banks */
+#define CFG_MAX_FLASH_SECT	256 /* max sectors per device */
+
+#undef	CFG_FLASH_CHECKSUM
+
+/*
+ * NAND flash on the local bus
+ */
+#define CONFIG_CMD_NAND		1
+#define CFG_NAND_BASE		0x60000000
+#define CFG_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS		1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CFG_LBLAWBAR1_PRELIM	CFG_NAND_BASE
+#define CFG_LBLAWAR1_PRELIM	0x8000001b /* Access window size 4K */
+
+/* Port size 8 bit, UPMA */
+#define CFG_BR1_PRELIM		(CFG_NAND_BASE|0x00000881)
+#define CFG_OR1_PRELIM		0xfc000001
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,}
+
+#define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2	(CFG_IMMR+0x4600)
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_HAS_BD_T	1
+#define CONFIG_OF_HAS_UBOOT_ENV	1
+
+#define OF_CPU			"PowerPC,8360 at 0"
+#define OF_SOC			"soc at e0000000"
+#define OF_QE			"qe at e0100000"
+#define OF_TBCLK		(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH		"/soc at e0000000/serial at 4500"
+
+/* I2C */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE	0x7F
+#define CFG_I2C_NOPROBES	{0x52} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET	0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
+#define CFG_I2C_RTC_ADDR	0x68	/* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI	1
+
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000 /* 256M */
+#define CFG_PCI1_MMIO_BASE	0x90000000
+#define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE	0x10000000 /* 256M */
+#define CFG_PCI1_IO_BASE	0xE0300000
+#define CFG_PCI1_IO_PHYS	0xE0300000
+#define CFG_PCI1_IO_SIZE	0x100000 /* 1M */
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"Freescale GETH"
+
+#define CONFIG_UEC_ETH1		/* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM	0	/* UCC1 */
+#define CFG_UEC1_RX_CLK		QE_CLK_NONE
+#define CFG_UEC1_TX_CLK		QE_CLK9
+#define CFG_UEC1_ETH_TYPE	GIGA_ETH
+#define CFG_UEC1_PHY_ADDR	2
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2		/* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM	1	/* UCC2 */
+#define CFG_UEC2_RX_CLK		QE_CLK_NONE
+#define CFG_UEC2_TX_CLK		QE_CLK4
+#define CFG_UEC2_ETH_TYPE	GIGA_ETH
+#define CFG_UEC2_PHY_ADDR	4
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+/*
+ * Environment
+ */
+
+#ifndef CFG_RAMBOOT
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+#define CFG_ENV_SIZE		0x20000
+#else /* CFG_RAMBOOT */
+#define CFG_NO_FLASH		1	/* Flash is not usable now */
+#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#define CFG_ENV_SIZE		0x2000
+#endif /* CFG_RAMBOOT */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ASKENV
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#endif
+
+#if defined(CFG_RAMBOOT)
+#undef CONFIG_CMD_ENV
+#undef CONFIG_CMD_LOADS
+#endif
+
+#undef CONFIG_WATCHDOG		/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP		/* undef to save memory */
+#define CFG_LOAD_ADDR		0x2000000 /* default load address */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+	#define CFG_CBSIZE	1024 /* Console I/O Buffer Size */
+#else
+	#define CFG_CBSIZE	256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT		0x000000000
+#define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
+#define CFG_HID2		HID2_HBE
+
+/*
+ * Cache Config
+ */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5 /*log base 2 of the above value */
+#endif
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L	CFG_IBAT0L
+#define CFG_DBAT0U	CFG_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CFG_IBAT1L	(CFG_IMMR | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT1U	(CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L	CFG_IBAT1L
+#define CFG_DBAT1U	CFG_IBAT1U
+
+/* NAND: cache-inhibit and guarded */
+#define CFG_IBAT2L	(CFG_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\
+			 BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U	(CFG_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L	CFG_IBAT2L
+#define CFG_DBAT2U	CFG_IBAT2U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT3L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT3L	(CFG_FLASH_BASE | BATL_PP_10 | \
+			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U	CFG_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT4L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT4U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT4L	CFG_IBAT4L
+#define CFG_DBAT4U	CFG_IBAT4U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CFG_IBAT5L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT5U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT6L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
+			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#else
+#define CFG_IBAT5L	(0)
+#define CFG_IBAT5U	(0)
+#define CFG_IBAT6L	(0)
+#define CFG_IBAT6U	(0)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#endif
+
+#define CFG_IBAT7L	(0)
+#define CFG_IBAT7U	(0)
+#define CFG_DBAT7L	CFG_IBAT7L
+#define CFG_DBAT7U	CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02 /* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETHADDR	00:04:9f:ef:01:01
+#define CONFIG_ETH1ADDR	00:04:9f:ef:01:02
+#define CONFIG_ETH2ADDR	00:04:9f:ef:01:03
+#define CONFIG_ETH3ADDR	00:04:9f:ef:01:04
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR	a00000
+#define CONFIG_HOSTNAME	mpc8360erdk
+#define CONFIG_BOOTFILE	uImage
+
+#define CONFIG_IPADDR		10.0.0.99
+#define CONFIG_SERVERIP		10.0.0.2
+#define CONFIG_GATEWAYIP	10.0.0.2
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_ROOTPATH		/nfsroot/
+
+#define	CONFIG_BOOTDELAY 2	/* -1 disables auto-boot */
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+   "netdev=eth0\0"\
+   "consoledev=ttyS0\0"\
+   "loadaddr=a00000\0"\
+   "fdtaddr=900000\0"\
+   "bootfile=uImage\0"\
+   "fdtfile=dtb\0"\
+   "fsfile=fs\0"\
+   "ubootfile=u-boot.bin\0"\
+   "mtdparts=mtdparts=60000000.nand-on-up:4096k(kernel),128k(dtb),-(rootfs)\0"\
+   "setbootargs=setenv bootargs console=$consoledev,$baudrate "\
+   		"$mtdparts panic=1\0"\
+   "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\
+   		"$gatewayip:$netmask:$hostname:$netdev:off "\
+   		"root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\
+   "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "\
+   		"rootfstype=jffs2 rw\0"\
+   "tftp_get_uboot=tftp 100000 $ubootfile\0"\
+   "tftp_get_kernel=tftp $loadaddr $bootfile\0"\
+   "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\
+   "tftp_get_fs=tftp c00000 $fsfile\0"\
+   "nand_erase_kernel=nand erase 0 400000\0"\
+   "nand_erase_dtb=nand erase 400000 20000\0"\
+   "nand_erase_fs=nand erase 420000 7be0000\0"\
+   "nand_write_kernel=nand write $loadaddr 0 400000\0"\
+   "nand_write_dtb=nand write $fdtaddr 400000 20000\0"\
+   "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"\
+   "nand_read_kernel=nand read $loadaddr 0 400000\0"\
+   "nand_read_dtb=nand read $fdtaddr 400000 20000\0"\
+   "nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\
+   		"cp.b 100000 ff800000 $filesize\0"\
+   "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "\
+   		"nand_write_kernel\0"\
+   "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
+   "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0"\
+   "nand_reflash=run nand_reflash_kernel nand_reflash_dtb "\
+   		"nand_reflash_fs\0"\
+   "boot_m=bootm $loadaddr - $fdtaddr\0"\
+   "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
+   		"boot_m\0"\
+   "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
+   		"boot_m\0"\
+   ""
+
+#define CONFIG_BOOTCOMMAND "run nfsboot"
+
+#endif /* __CONFIG_H */
-- 
1.5.2.2





More information about the U-Boot mailing list