[U-Boot-Users] ethernet on FCC

[Jerry Van Baren]

jie han wrote:
> Hi,
> My mpc8270 board use three ehternet ports at FCC1,FCC2,FCC3.it is
> work well at FCC1.When I use port FCC2, I found out the
> u-boot is not receiving packets (It's sending correct packet when i
> use ethereal for sniffing). When trying "ping", it generated an ARP
> packet first, the other host replied with , but the board never seems
> to receive it(set printf at function fec_recv()  
> /cpu/mpc8260/ether_fcc.c ).all three ethernet fcc ports initiailze is 
> same.Do I miss something?thank you for your suggestion,my config file 
> config FCC port parameter as follow:
> 
> #undef    CONFIG_ETHER_ON_SCC        /* define if ether on SCC   */
> #define CONFIG_ETHER_ON_FCC        /* define if ether on FCC   */
> #undef    CONFIG_ETHER_NONE          /* define if ether on something else */
> #define    CONFIG_NET_MULTI
> #define CONFIG_ETHER_ON_FCC1
> #define CONFIG_ETHER_ON_FCC2
> #define CONFIG_ETHER_ON_FCC3
> 
> #define CFG_CMXFCR_VALUE1    (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
> #define CFG_CMXFCR_MASK1    (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | 
> CMXFCR_TF1CS_MSK)
> 
> #define CFG_CMXFCR_VALUE3    (CMXFCR_RF3CS_CLK13 | CMXFCR_TF3CS_CLK14)
> #define CFG_CMXFCR_MASK3    (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | 
> CMXFCR_TF3CS_MSK)
> 
> #define CFG_CMXFCR_VALUE2    (CMXFCR_RF2CS_CLK15 | CMXFCR_TF2CS_CLK16)
> #define CFG_CMXFCR_MASK2    (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | 
> CMXFCR_TF2CS_MSK)
> 
> #define CFG_RX_ETH_BUFFER       128    
> #define CONFIG_IPADDR           192.168.10.17
> #define CONFIG_SERVERIP         192.168.10.101
> #define CONFIG_HOSTNAME         OceanSCC
> #define CONFIG_LOADADDR         1000    /* default location for tftp and 
> bootm */
> #define CONFIG_BOOTFILE              u-boot.bin
> 
> #define CONFIG_ETHADDR          00:13:09:11:22:33
> #define CONFIG_HAS_ETH1
> #define CONFIG_ETH1ADDR                    00:13:09:04:05:36
> #define CONFIG_HAS_ETH2
> #define CONFIG_ETH2ADDR                    00:13:09:07:08:39
> 
> #define    CONFIG_EXTRA_ENV_SETTINGS    "ethprime=FCC1 ETHERNET"
> 
> #define CFG_CPMFCR_RAMTYPE    0        /* BDs and buffers on 60x bus */
> #define CFG_FCC_PSMR        (FCC_PSMR_FDE | FCC_PSMR_LPB)  /* Full duplex */
> 
> #define CONFIG_MII            /* MII PHY management        */
> #define CONFIG_BITBANGMII        /* bit-bang MII PHY management    */
> 
> Sincerely,
> 
> Jie

Hi Jie,

I don't have any good insights, but some things to try:
* Are you sure, positive, double checked and had a co-worker check that 
your clock input for FCC2-Rx is configured properly?
   1) Which CLK input is used?
   2) The port/pin configuration initialization in u-boot?
   3) Your hardware (traces) actually connect the right pins?

* Does FCC3 work?

* If you turn off CONFIG_NET_MULTI and only use FCC2, does it work?

* If you turn off CONFIG_NET_MULTI and only use FCC3, does it work?

Good luck,
gvb