[U-Boot-Users] [PATCH 2/4] include/configs: Use new CONFIG_CMD_* in 85xx board config files.

Jon Loeliger jdl at jdl.com
Wed Jun 13 20:22:08 CEST 2007 

Signed-off-by: Jon Loeliger <jdl at freescale.com>
---

This is all 85xx boards, not just the Freescale 85xx boards.

Tested by building all boards in ./MAKEALL 85xx.

Note that very minor liberties were taken in a few of these conversions.
Specifically, I did not care much if I slightly altered the set of
commands that were present under the nefarious CFG_RAMBOOT setting
if it made the general case simpler and clearer.

 include/configs/MPC8540ADS.h  |   49 ++++++++++++---------------------
 include/configs/MPC8540EVAL.h |   36 +++++++++++-------------
 include/configs/MPC8541CDS.h  |   28 +++++++++---------
 include/configs/MPC8544DS.h   |   33 +++++++++++-----------
 include/configs/MPC8548CDS.h  |   28 +++++++++---------
 include/configs/MPC8555CDS.h  |   28 +++++++++---------
 include/configs/MPC8560ADS.h  |   61 ++++++++++++++---------------------------
 include/configs/MPC8568MDS.h  |   29 ++++++++++---------
 include/configs/PM854.h       |   58 ++++++++++++++-------------------------
 include/configs/PM856.h       |   55 +++++++++++++-----------------------
 include/configs/SBC8540.h     |   46 +++++++++++++++---------------
 include/configs/TQM85xx.h     |   38 +++++++++++++------------
 include/configs/sbc8560.h     |   44 +++++++++++++++---------------
 include/configs/stxgp3.h      |   51 +++++++++++++++-------------------
 include/configs/stxssa.h      |   46 ++++++++++++++-----------------
 15 files changed, 280 insertions(+), 350 deletions(-)

diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 5aeea58..bc562a3 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -407,37 +407,24 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_PCI		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #else
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_PCI		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #else
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -448,7 +435,7 @@
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -469,7 +456,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -481,7 +468,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index 418a3a3..2b0bd9b 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -259,26 +259,24 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
-#if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING \
-				| CFG_CMD_PCI | CFG_CMD_I2C ) & \
-				 ~(CFG_CMD_ENV | CFG_CMD_LOADS ))
-#else
-#define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING \
-				| CFG_CMD_I2C ) & \
-				 ~(CFG_CMD_ENV | CFG_CMD_LOADS ))
-#endif
-#else
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI \
-				| CFG_CMD_PING | CFG_CMD_I2C )
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_I2C )
+    #define CONFIG_CMD_PCI
 #endif
+
+#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -288,7 +286,7 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_LOAD_ADDR   0x2000000       /* default load address */
 #define CFG_PROMPT	"MPC8540EVAL=> "/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -308,7 +306,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
@@ -320,7 +318,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index fb360d2..78e603c 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -401,19 +401,19 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PCI \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
+    #define CONFIG_CMD_PCI
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -423,7 +423,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -443,7 +443,7 @@ extern unsigned long get_clock_freq(void);
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -455,7 +455,7 @@ extern unsigned long get_clock_freq(void);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 4c34308..2d86d3e 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -392,21 +392,22 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define	CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PCI \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII \
-				| CFG_CMD_BEDBUG \
-				| CFG_CMD_NET)
-#else
-#define	CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
+    #define CONFIG_CMD_PCI
+    #define CONFIG_CMD_BEDBUG
+    #define CONFIG_CMD_NET
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -416,7 +417,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -436,7 +437,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -448,7 +449,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 680009d..ceec7a9 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -427,19 +427,19 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PCI \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
+    #define CONFIG_CMD_PCI
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -449,7 +449,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -469,7 +469,7 @@ extern unsigned long get_clock_freq(void);
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -481,7 +481,7 @@ extern unsigned long get_clock_freq(void);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 4c8b4e7..6a4ebb8 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -401,19 +401,19 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PCI \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
+    #define CONFIG_CMD_PCI
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -423,7 +423,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -443,7 +443,7 @@ extern unsigned long get_clock_freq(void);
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -455,7 +455,7 @@ extern unsigned long get_clock_freq(void);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 21e6637..0b4464b 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -432,46 +432,27 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_PCI		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #elif defined(CONFIG_TSEC_ENET)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)		\
-				& ~(CFG_CMD_ENV))
-  #elif defined(CONFIG_ETHER_ON_FCC)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_MII		\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_I2C)		\
-				& ~(CFG_CMD_ENV))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_PCI		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #elif defined(CONFIG_TSEC_ENET)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #elif defined(CONFIG_ETHER_ON_FCC)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_MII		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -482,7 +463,7 @@
 #define CFG_LOAD_ADDR	0x1000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -503,7 +484,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -515,7 +496,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 3f65644..3aba995 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -383,19 +383,20 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PCI \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
-#else
-#define  CONFIG_COMMANDS	(CONFIG_CMD_DFL \
-				| CFG_CMD_PING \
-				| CFG_CMD_I2C \
-				| CFG_CMD_MII)
+    #define CONFIG_CMD_PCI
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -405,7 +406,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CFG_CBSIZE	256			/* Console I/O Buffer Size */
@@ -425,7 +426,7 @@ extern unsigned long get_clock_freq(void);
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE	32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -437,7 +438,7 @@ extern unsigned long get_clock_freq(void);
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index 4fb5440..465b472 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -303,43 +303,27 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_EEPROM
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_PCI		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #else
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_EEPROM	\
-				| CFG_CMD_DATE		\
-				| CFG_CMD_MII		\
-				| CFG_CMD_PCI		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #else
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_EEPROM	\
-				| CFG_CMD_DATE		\
-				| CFG_CMD_MII		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -350,7 +334,7 @@
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -372,7 +356,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -384,7 +368,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index 87ab934..25c6e15 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -306,41 +306,26 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_EEPROM
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_PCI		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #else
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
-				 | CFG_CMD_PING		\
-				 | CFG_CMD_I2C)		\
-				&			\
-				 ~(CFG_CMD_ENV		\
-				  | CFG_CMD_LOADS))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_EEPROM	\
-				| CFG_CMD_DATE		\
-				| CFG_CMD_PCI		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #else
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
-				| CFG_CMD_EEPROM	\
-				| CFG_CMD_DATE		\
-				| CFG_CMD_PING		\
-				| CFG_CMD_I2C)
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
@@ -351,7 +336,7 @@
 #define CFG_LOAD_ADDR	0x1000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -373,7 +358,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -385,7 +370,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index f8e3397..a5397c2 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -338,28 +338,28 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				 ~(CFG_CMD_ENV | \
-				  CFG_CMD_LOADS ))
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				~(CFG_CMD_ENV))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #endif
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
+#if defined(CFG_RAMBOOT)
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -368,7 +368,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"SBC8540=> " /* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
   #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -389,7 +389,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
@@ -401,7 +401,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
   #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index f45f3a2..3b746df 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -357,24 +357,26 @@
 
 #define	CONFIG_TIMESTAMP		/* Print image info with ts	*/
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-# define ADD_PCI_CMD		(CFG_CMD_PCI)
-#else
-# define ADD_PCI_CMD		0
+    #define CONFIG_CMD_PCI
 #endif
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL	| \
-				 CFG_CMD_DHCP	| \
-				 CFG_CMD_NFS	| \
-				 CFG_CMD_SNTP	| \
-				 ADD_PCI_CMD	| \
-				 CFG_CMD_I2C	| \
-				 CFG_CMD_DATE	| \
-				 CFG_CMD_EEPROM	| \
-				 CFG_CMD_DTT	| \
-				 CFG_CMD_MII	| \
-				 CFG_CMD_PING	)
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -385,7 +387,7 @@
 #define CFG_LOAD_ADDR	0x2000000	/* default load address		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -406,7 +408,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value	*/
 #endif
 
@@ -418,7 +420,7 @@
 #define BOOTFLAG_COLD	0x01		/* Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
 #endif
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 6e4fdb2..ad610f0 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -320,28 +320,28 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
 #if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				 ~(CFG_CMD_ENV | \
-				  CFG_CMD_LOADS ))
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				~(CFG_CMD_ENV))
-  #endif
-#else
-  #if defined(CONFIG_PCI)
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #elif (defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC))
-    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C)
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -350,7 +350,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"SBC8560=> " /* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
   #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -371,7 +371,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
@@ -383,7 +383,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
   #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
   #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 625cf20..0a1331d 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -298,34 +298,29 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				 ~(CFG_CMD_ENV | \
-				  CFG_CMD_LOADS ))
-  #elif defined(CONFIG_TSEC_ENET)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING | \
-				CFG_CMD_MII | CFG_CMD_I2C ) & \
-				~(CFG_CMD_ENV))
-  #elif defined(CONFIG_ETHER_ON_FCC)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				~(CFG_CMD_ENV))
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #else
-  #if defined(CONFIG_PCI)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
-  #elif defined(CONFIG_TSEC_ENET)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PING | \
-				CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C)
-  #elif defined(CONFIG_ETHER_ON_FCC)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
-  #endif
+    #define CONFIG_CMD_ELF
+#endif
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
 #endif
-#include <cmd_confdefs.h>
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -334,7 +329,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"GPPP=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -355,7 +350,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
@@ -367,7 +362,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot		*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 1978a32..cea5b7e 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -325,34 +325,30 @@
 
 #define	CONFIG_TIMESTAMP		/* Print image info with ts	*/
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+    #define CONFIG_CMD_MII
+#endif
+
 #if defined(CFG_RAMBOOT)
-  #if defined(CONFIG_PCI)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				 ~(CFG_CMD_ENV | \
-				  CFG_CMD_LOADS ))
-  #elif defined(CONFIG_TSEC_ENET)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING | \
-				CFG_CMD_MII | CFG_CMD_I2C ) & \
-				~(CFG_CMD_ENV))
-  #elif defined(CONFIG_ETHER_ON_FCC)
-  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_PING | CFG_CMD_I2C) & \
-				~(CFG_CMD_ENV))
-  #endif
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #else
-  #if defined(CONFIG_PCI)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
-				CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
-  #elif defined(CONFIG_TSEC_ENET)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PING | \
-				CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C)
-  #elif defined(CONFIG_ETHER_ON_FCC)
-  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
-				CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
-  #endif
+    #define CONFIG_CMD_ELF
 #endif
-#include <cmd_confdefs.h>
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-- 
1.5.2.1.239.g75d8

More information about the U-Boot mailing list