[U-Boot] [PATCH] RE: Some memory (DDR2 ECC Dual Rank) just doesn't work! Can anyone pointme to how to debug this hang?

Vince Asbridge vasbridge at sanblaze.com
Thu Aug 14 18:05:00 CEST 2008


Stephane,

Thanks so much for your prompt reply.

We will pursue your suggestions, and let the forum know what we find.  We're
at 1.3.0 uboot version.

Vince

> -----Original Message-----
> From: Fillod Stephane [mailto:stephane.fillod at thomson.net] 
> Sent: Thursday, August 14, 2008 8:06 AM
> To: Vince Asbridge; linuxppc-embedded
> Cc: u-boot at lists.denx.de
> Subject: [PATCH] RE: Some memory (DDR2 ECC Dual Rank) just 
> doesn't work! Can anyone pointme to how to debug this hang?
> 
> Vince Asbridge wrote:
> > We have an 8548 design, which implements a DDR2 on a SODIMM 
> We have an 
> > issue with dual rank memory (specific part number Viking 
> VR5DR287218EBSS1), which is a 1G ECC Registered SODIMM part, 
> with two ranks.
> > Our platform wires CS0 and CS1 to the SODIMM slot. 
> > At uBoot, all is well.  Memory is discovered as ECC 533, 1G 
> DDR2 64Bit 4 beat bursts, and mtest can read and write all 1G 
> of the SODIMM.
> [...]
> > Other DDR2s (identical except for vendor and # of ranks), 
> work perfectly! 
> > Anyone got a clue what I could look at to try to figure this out? 
> > We've tried enable / disable ECC at uboot We've tried 
> enable / disable 
> > Interleaving at uboot uboot always works (and can read/write entire 
> > DDR), Linux always hangs on boot!
> 
> U-Boot is too gentle when testing SDRAM. Make sure the caches 
> are enabled under U-Boot, and put on heavy stress with DMA, 
> pipelined prefetch's, etc.
> This is what your CPU is enduring under Linux. 
> 
> Your question is definitely a question for the U-Boot mailing list.
> BTW, what is the version of U-Boot in use? U-Boot is still 
> missing the following patch:
> 
> MPC85xx BA bits not set for 3-bit bank address DIMM of CS1
> 
> The current implementation set the number of bank address bits
> (BA) in the processor for CS0 but not for CS1. 
> 
> Signed-off-by: Stephane Fillod <stephane.fillod at thomson.net>
> 
> --- u-boot/cpu/mpc85xx/spd_sdram.c
> +++ u-boot/cpu/mpc85xx/spd_sdram.c
> @@ -365,6 +365,7 @@
>                 ddr->cs1_config = ( 1<<31
>                                     | (odt_rd_cfg << 20)
>                                     | (odt_wr_cfg << 16)
> +                                   | (ba_bits << 14)
>                                     | (spd.nrow_addr - 12) << 8
>                                     | (spd.ncol_addr - 8) );
>                 debug("DDR: cs1_bnds   = 0x%08x\n", ddr->cs1_bnds);
> 
> 
> 
> Otherwise, recompile with -DDEBUG and CFG_CMD_SDRAM, grab the 
> Viking datasheet and a scope, and a full cup of coffee/tea 
> much needed during cross-checking :-)
> 
> Cheers
> --
> Stephane
> 
> 
> 




More information about the U-Boot mailing list