[U-Boot] [PATCH v3 10/16] FSL DDR: Convert MPC8544DS to new DDR code.
Kumar Gala
galak at kernel.crashing.org
Thu Aug 21 01:22:52 CEST 2008
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
Makefile | 1 +
board/freescale/mpc8544ds/Makefile | 9 +-
board/freescale/mpc8544ds/ddr.c | 242 +++++++++++++++++++++++++++++++++
board/freescale/mpc8544ds/mpc8544ds.c | 11 +-
cpu/mpc85xx/Makefile | 2 +-
include/configs/MPC8544DS.h | 52 ++++++--
6 files changed, 298 insertions(+), 19 deletions(-)
create mode 100644 board/freescale/mpc8544ds/ddr.c
diff --git a/Makefile b/Makefile
index 7da88dc..65ca5e2 100644
--- a/Makefile
+++ b/Makefile
@@ -236,6 +236,7 @@ LIBS += drivers/qe/qe.a
endif
ifeq ($(CPU),mpc85xx)
LIBS += drivers/qe/qe.a
+LIBS += cpu/mpc8xxx/libmpc8xxx.a
endif
ifeq ($(CPU),mpc86xx)
LIBS += cpu/mpc8xxx/libmpc8xxx.a
diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile
index 3a5ea00..3997994 100644
--- a/board/freescale/mpc8544ds/Makefile
+++ b/board/freescale/mpc8544ds/Makefile
@@ -26,10 +26,13 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o law.o tlb.o
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/freescale/mpc8544ds/ddr.c b/board/freescale/mpc8544ds/ddr.c
new file mode 100644
index 0000000..d3e0ca8
--- /dev/null
+++ b/board/freescale/mpc8544ds/ddr.c
@@ -0,0 +1,242 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <../cpu/mpc8xxx/fsl_ddr_sdram.h>
+
+#define SDRAM_TYPE_DDR1 2
+#define SDRAM_TYPE_DDR2 3
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+ return get_ddr_freq(0);
+}
+
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+
+ if (ctrl_num) {
+ printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+ return;
+ }
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS1);
+ }
+}
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+void fsl_ddr_dump_memctl_regs(unsigned int ctrl_num)
+{
+ unsigned int i;
+ volatile ccsr_ddr_t *ddr = (void *)CFG_MPC85xx_DDR_ADDR;
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ unsigned int bnds = 0;
+ unsigned int config = 0;
+ unsigned int *pbnds = NULL;
+ unsigned int *pconfig = NULL;
+
+ if (i == 0) {
+ bnds = ddr->cs0_bnds;
+ config = ddr->cs0_config;
+ pbnds = (unsigned int *)&ddr->cs0_bnds;
+ pconfig = (unsigned int *)&ddr->cs0_config;
+
+ } else if (i == 1) {
+ bnds = ddr->cs1_bnds;
+ config = ddr->cs1_config;
+ pbnds = (unsigned int *)&ddr->cs1_bnds;
+ pconfig = (unsigned int *)&ddr->cs1_config;
+
+ } else if (i == 2) {
+ bnds = ddr->cs2_bnds;
+ config = ddr->cs2_config;
+ pbnds = (unsigned int *)&ddr->cs2_bnds;
+ pconfig = (unsigned int *)&ddr->cs2_config;
+
+ } else {
+ bnds = ddr->cs3_bnds;
+ config = ddr->cs3_config;
+ pbnds = (unsigned int *) &ddr->cs3_bnds;
+ pconfig = (unsigned int *) &ddr->cs3_config;
+ }
+
+ printf("cs%u_bnds = %08X\t%p\n", i, bnds, pbnds);
+ printf("cs%u_config = %08X\t%p\n", i, config, pconfig);
+ }
+
+ /*
+ * Due to inconsistencies between immap_85xx.h and immap_86xx.h,
+ * you will have to modify the structure member names by hand
+ * between architectures.
+ */
+ printf("timing_cfg_3 = %08X\t%p\n",
+ ddr->timing_cfg_3, &ddr->timing_cfg_3);
+ printf("timing_cfg_0 = %08X\t%p\n",
+ ddr->timing_cfg_0, &ddr->timing_cfg_0);
+ printf("timing_cfg_1 = %08X\t%p\n",
+ ddr->timing_cfg_1, &ddr->timing_cfg_1);
+ printf("timing_cfg_2 = %08X\t%p\n",
+ ddr->timing_cfg_2, &ddr->timing_cfg_2);
+ printf("ddr_sdram_cfg = %08X\t%p\n",
+ ddr->sdram_cfg, &ddr->sdram_cfg);
+ printf("ddr_sdram_cfg_2 = %08X\t%p\n",
+ ddr->sdram_cfg_2, &ddr->sdram_cfg_2);
+ printf("ddr_sdram_mode = %08X\t%p\n",
+ ddr->sdram_mode, &ddr->sdram_mode);
+ printf("ddr_sdram_mode_2 = %08X\t%p\n",
+ ddr->sdram_mode_2, &ddr->sdram_mode_2);
+ printf("ddr_sdram_md_cntl = %08X\t%p\n",
+ ddr->sdram_md_cntl, &ddr->sdram_md_cntl);
+ printf("ddr_sdram_interval = %08X\t%p\n",
+ ddr->sdram_interval, &ddr->sdram_interval);
+ printf("ddr_data_init = %08X\t%p\n",
+ ddr->sdram_data_init, &ddr->sdram_data_init);
+ printf("ddr_sdram_clk_cntl = %08X\t%p\n",
+ ddr->sdram_clk_cntl, &ddr->sdram_clk_cntl);
+ printf("ddr_init_addr = %08X\t%p\n",
+ ddr->init_addr, &ddr->init_addr);
+ printf("ddr_init_ext_addr = %08X\t%p\n",
+ ddr->init_ext_addr, &ddr->init_ext_addr);
+}
+
+
+void fsl_ddr_set_memctl_regs(const fsl_memctl_config_regs_t *regs,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ volatile ccsr_ddr_t *ddr = (void *)CFG_MPC85xx_DDR_ADDR;
+
+ if (ctrl_num) {
+ printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+ return;
+ }
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i == 0) {
+ ddr->cs0_bnds = regs->cs[i].bnds;
+ ddr->cs0_config = regs->cs[i].config;
+
+ } else if (i == 1) {
+ ddr->cs1_bnds = regs->cs[i].bnds;
+ ddr->cs1_config = regs->cs[i].config;
+
+ } else if (i == 2) {
+ ddr->cs2_bnds = regs->cs[i].bnds;
+ ddr->cs2_config = regs->cs[i].config;
+
+ } else if (i == 3) {
+ ddr->cs3_bnds = regs->cs[i].bnds;
+ ddr->cs3_config = regs->cs[i].config;
+ }
+ }
+
+ /*
+ * Someone decided to use different names from the documentation...
+ */
+ ddr->timing_cfg_3 = regs->timing_cfg_3;
+ ddr->timing_cfg_0 = regs->timing_cfg_0;
+ ddr->timing_cfg_1 = regs->timing_cfg_1;
+ ddr->timing_cfg_2 = regs->timing_cfg_2;
+ ddr->sdram_cfg_2 = regs->ddr_sdram_cfg_2;
+ ddr->sdram_mode = regs->ddr_sdram_mode;
+ ddr->sdram_mode_2 = regs->ddr_sdram_mode_2;
+ ddr->sdram_interval = regs->ddr_sdram_interval;
+ ddr->sdram_data_init = regs->ddr_data_init;
+ ddr->sdram_clk_cntl = regs->ddr_sdram_clk_cntl;
+ ddr->init_addr = regs->ddr_init_addr;
+ ddr->init_ext_addr = regs->ddr_init_ext_addr;
+
+ /* FIXME: ECC? Need to program err_disable, err_sbe, and err_int_en */
+
+ /*
+ * 200 painful micro-seconds must elapse between
+ * the DDR clock setup and the DDR config enable.
+ */
+ udelay(200);
+ asm volatile("sync;isync");
+
+ ddr->sdram_cfg = regs->ddr_sdram_cfg;
+
+ /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */
+ while (ddr->sdram_cfg_2 & 0x10) {
+ udelay(10000); /* throttle polling rate */
+ }
+}
+
+unsigned int fsl_ddr_type_function(void)
+{
+ return SDRAM_TYPE_DDR2;
+}
+
+/*
+ * factors to consider for clock adjust:
+ * - number of chips on bus
+ * - position of slot
+ * - DDR1 vs. DDR2?
+ * - ???
+ *
+ * FIXME: need to figure out the function parameters necessary to compute
+ * FIXME: a clock adjust value
+ */
+unsigned int fsl_ddr_clk_adjust_function(void)
+{
+ return 7;
+}
+
+/*
+ * factors to consider for CPO:
+ * - frequency
+ * - ddr1 vs. ddr2
+ *
+ * FIXME: figure out how to compute or tabulate good values for this
+ */
+unsigned int fsl_ddr_cpo_override_function(void)
+{
+ return 10;
+}
+
+/*
+ * factors to consider for write data delay:
+ * - number of DIMMs
+ *
+ * 1 = 1/4 clock delay
+ * 2 = 1/2 clock delay
+ * 3 = 3/4 clock delay
+ * 4 = 1 clock delay
+ * 5 = 5/4 clock delay
+ * 6 = 3/2 clock delay
+ */
+unsigned int fsl_ddr_write_data_delay_function(void)
+{
+ return 3;
+}
+
+/*
+ * factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+unsigned int fsl_ddr_half_strength_driver_enable_function(void)
+{
+ return 0;
+}
diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c
index c39ce11..213539e 100644
--- a/board/freescale/mpc8544ds/mpc8544ds.c
+++ b/board/freescale/mpc8544ds/mpc8544ds.c
@@ -24,22 +24,21 @@
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
+#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/immap_fsl_pci.h>
#include <asm/io.h>
-#include <spd_sdram.h>
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
#include "../common/pixis.h"
+#include "../cpu/mpc8xxx/fsl_ddr_sdram.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
-void sdram_init(void);
-
int checkboard (void)
{
volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
@@ -69,7 +68,11 @@ initdram(int board_type)
puts("Initializing\n");
- dram_size = spd_sdram();
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+ dram_size *= 0x100000;
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
diff --git a/cpu/mpc85xx/Makefile b/cpu/mpc85xx/Makefile
index c180dbd..d51a6dd 100644
--- a/cpu/mpc85xx/Makefile
+++ b/cpu/mpc85xx/Makefile
@@ -43,7 +43,7 @@ endif
endif
COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o tlb.o \
- pci.o serial_scc.o commproc.o ether_fcc.o spd_sdram.o qe_io.o \
+ pci.o serial_scc.o commproc.o ether_fcc.o qe_io.o \
$(COBJS-y)
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 9a77b7b..8feda9b 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -46,15 +46,6 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_DLL
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_DDR_ECC_CMD
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
/*
@@ -64,8 +55,6 @@
*/
#define CONFIG_ASSUME_AMD_FLASH
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
-
#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy);
#endif
@@ -104,6 +93,44 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
/*
* DDR Setup
*/
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+/*
+ * Number of memory controllers on device
+ */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+
+/*
+ * Number of DIMM slots per memory controller
+ */
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+
+/*
+ * Number of chip selects per memory controller
+ *
+ * The MPC8544 (the chip) has 4 chip selects per memory controller.
+ * However, the MPC8544DS (the board) has only 1 DIMM slot per memory
+ * controller, so therefore it only has 2 chip selects per memory
+ * controller that are actually connected.
+ */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/*
+ * I2C addresses of SPD EEPROMs
+ */
+#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
+
+
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
@@ -242,6 +269,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+#define CFG_64BIT_STRTOUL 1
+#define CFG_64BIT_VSPRINTF 1
+
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
--
1.5.5.1
More information about the U-Boot
mailing list