[U-Boot-Users] [PATCH (RESUBMIT)] ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board

[Stefan Roese]

Hi Larry,

On Friday 04 January 2008, Lawrence R. Johnson wrote:
> Note: this patch changes the configuration of some GPIO registers:
>
>    Register      Old Value   New Value
> ---------------  ----------  ----------
> DCR GPIO0_TCR    0x0000000F  0x0000F0CF
> DCR GPIO0_TSRH   0x55005000  0x00000000
> DCR GPIO1_TCR    0xC2000000  0xE2000000
> DCR GPIO1_TSRL   0x0C000000  0x00200000
> DCR GPIO1_ISR2L  0x00050000  0x00110000
>
> Signed-off-by: Larry Johnson <lrj at acm.org>
> ---
> Hi Stefan,
>
> This is my attempt to use apply the new GPIO configuration to the
> Sequoia board.  I didn't find much about GPIO in the Sequoia manual, so
> I just tried to produce a table that matched the current Sequoia
> configuration as closely as possible.
>
> I think the changed values above are OK.  The TCR and TSR changes are
> generated from the table, and should be correct.  The ISR change
> reflects that GPIO37 Alt2 is bidirectional, and GPIO38 Alt2 is an
> output.

Thanks a lot for the good work. Really appreciated. I'll re-check the Sequouia 
values again.

Please find one further comment below.

> Best regards,
> Larry
>
> N.B.: This patch depends on my previously-submitted patch for GPIO.
>
>  board/amcc/sequoia/sequoia.c |   31 +------------
>  include/configs/sequoia.h    |  106
> ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 107
> insertions(+), 30 deletions(-)
>
> diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
> index 37b4f31..2268bc0 100644
> --- a/board/amcc/sequoia/sequoia.c
> +++ b/board/amcc/sequoia/sequoia.c
> @@ -26,6 +26,7 @@
>  #include <libfdt.h>
>  #include <fdt_support.h>
>  #include <ppc440.h>
> +#include <asm/gpio.h>
>  #include <asm/processor.h>
>  #include <asm/io.h>
>
> @@ -45,36 +46,6 @@ int board_early_init_f(void)
>  	mtdcr(ebccfgd, 0xb8400000);
>
>  	/*--------------------------------------------------------------------
> -	 * Setup the GPIO pins
> -	 *-------------------------------------------------------------------*/
> -	/* test-only: take GPIO init from pcs440ep ???? in config file */
> -	out_be32((u32 *) GPIO0_OR, 0x00000000);
> -	out_be32((u32 *) GPIO0_TCR, 0x0000000f);
> -	out_be32((u32 *) GPIO0_OSRL, 0x50015400);
> -	out_be32((u32 *) GPIO0_OSRH, 0x550050aa);
> -	out_be32((u32 *) GPIO0_TSRL, 0x50015400);
> -	out_be32((u32 *) GPIO0_TSRH, 0x55005000);
> -	out_be32((u32 *) GPIO0_ISR1L, 0x50000000);
> -	out_be32((u32 *) GPIO0_ISR1H, 0x00000000);
> -	out_be32((u32 *) GPIO0_ISR2L, 0x00000000);
> -	out_be32((u32 *) GPIO0_ISR2H, 0x00000100);
> -	out_be32((u32 *) GPIO0_ISR3L, 0x00000000);
> -	out_be32((u32 *) GPIO0_ISR3H, 0x00000000);
> -
> -	out_be32((u32 *) GPIO1_OR, 0x00000000);
> -	out_be32((u32 *) GPIO1_TCR, 0xc2000000);
> -	out_be32((u32 *) GPIO1_OSRL, 0x5c280000);
> -	out_be32((u32 *) GPIO1_OSRH, 0x00000000);
> -	out_be32((u32 *) GPIO1_TSRL, 0x0c000000);
> -	out_be32((u32 *) GPIO1_TSRH, 0x00000000);
> -	out_be32((u32 *) GPIO1_ISR1L, 0x00005550);
> -	out_be32((u32 *) GPIO1_ISR1H, 0x00000000);
> -	out_be32((u32 *) GPIO1_ISR2L, 0x00050000);
> -	out_be32((u32 *) GPIO1_ISR2H, 0x00000000);
> -	out_be32((u32 *) GPIO1_ISR3L, 0x01400000);
> -	out_be32((u32 *) GPIO1_ISR3H, 0x00000000);
> -
> -	/*--------------------------------------------------------------------
>  	 * Setup the interrupt controller polarities, triggers, etc.
>  	 *-------------------------------------------------------------------*/
>  	mtdcr(uic0sr, 0xffffffff);	/* clear all */
> diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
> index 1f72b54..86dd9d6 100644
> --- a/include/configs/sequoia.h
> +++ b/include/configs/sequoia.h
> @@ -476,6 +476,112 @@
>  #define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
>  #define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
>
> +/*-----------------------------------------------------------------------
> + * PPC440 GPIO Configuration
> + */
> +/* test-only: take GPIO init from pcs440ep ???? in config file */
> +/*
> +	TEST_DCR(GPIO0_OR, 0x00000000);
> +	TEST_DCR(GPIO0_TCR, 0x0000000f);
> +	TEST_DCR(GPIO0_OSRL, 0x50015400);
> +	TEST_DCR(GPIO0_OSRH, 0x550050aa);
> +	TEST_DCR(GPIO0_TSRL, 0x50015400);
> +	TEST_DCR(GPIO0_TSRH, 0x55005000);
> +	TEST_DCR(GPIO0_ISR1L, 0x50000000);
> +	TEST_DCR(GPIO0_ISR1H, 0x00000000);
> +	TEST_DCR(GPIO0_ISR2L, 0x00000000);
> +	TEST_DCR(GPIO0_ISR2H, 0x00000100);
> +	TEST_DCR(GPIO0_ISR3L, 0x00000000);
> +	TEST_DCR(GPIO0_ISR3H, 0x00000000);
> +
> +
> +	TEST_DCR(GPIO1_OR, 0x00000000);
> +	TEST_DCR(GPIO1_TCR, 0xc2000000);
> +	TEST_DCR(GPIO1_OSRL, 0x5c280000);
> +	TEST_DCR(GPIO1_OSRH, 0x00000000);
> +	TEST_DCR(GPIO1_TSRL, 0x0c000000);
> +	TEST_DCR(GPIO1_TSRH, 0x00000000);
> +	TEST_DCR(GPIO1_ISR1L, 0x00005550);
> +	TEST_DCR(GPIO1_ISR1H, 0x00000000);
> +	TEST_DCR(GPIO1_ISR2L, 0x00050000);
> +	TEST_DCR(GPIO1_ISR2H, 0x00000000);
> +	TEST_DCR(GPIO1_ISR3L, 0x01400000);
> +	TEST_DCR(GPIO1_ISR3H, 0x00000000);
> +*/

What are these TEST_DCR()'s for? Please remove and resumbit.

Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================