[U-Boot-Users] [PATCH V2] ppc4xx: Complete DU440 board support
Stefan Roese
sr at denx.de
Wed Jan 16 12:20:22 CET 2008
On Wednesday 16 January 2008, Matthias Fuchs wrote:
> Signed-off-by: Matthias Fuchs <matthias.fuchs at esd-electronics.com>
Comments below.
> MAINTAINERS | 1 +
> MAKEALL | 1 +
> Makefile | 3 +
> include/configs/DU440.h | 438
> +++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 443
> insertions(+), 0 deletions(-)
> create mode 100644 include/configs/DU440.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 2ef2f5c..1996688 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -150,6 +150,7 @@ Matthias Fuchs <matthias.fuchs at esd-electronics.com>
> DASA_SIM IOP480 (PPC401)
> DP405 PPC405EP
> DU405 PPC405GP
> + DU440 PPC440EPx
> G2000 PPC405EP
> HH405 PPC405EP
> HUB405 PPC405EP
> diff --git a/MAKEALL b/MAKEALL
> index ebc5a22..0777dac 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -175,6 +175,7 @@ LIST_4xx=" \
> DASA_SIM \
> DP405 \
> DU405 \
> + DU440 \
> ebony \
> ERIC \
> EXBITGEN \
> diff --git a/Makefile b/Makefile
> index 1983ca0..7de2286 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -1191,6 +1191,9 @@ DP405_config: unconfig
> DU405_config: unconfig
> @$(MKCONFIG) $(@:_config=) ppc ppc4xx du405 esd
>
> +DU440_config: unconfig
> + @$(MKCONFIG) $(@:_config=) ppc ppc4xx du440 esd
> +
> ebony_config: unconfig
> @$(MKCONFIG) $(@:_config=) ppc ppc4xx ebony amcc
>
> diff --git a/include/configs/DU440.h b/include/configs/DU440.h
> new file mode 100644
> index 0000000..30ac437
> --- /dev/null
> +++ b/include/configs/DU440.h
> @@ -0,0 +1,438 @@
> +/*
> + * (C) Copyright 2008
> + * Matthias Fuchs, esd gmbh, matthias.fuchs at esd-electronics.com
> + *
> + * based on the Sequoia board configuration by
> + * Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +/************************************************************************
> + * DU440.h - configuration for esd DU440 board (PowerPC440EPx)
> + ***********************************************************************/
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +/*-----------------------------------------------------------------------
> + * High Level Configuration Options
> + *----------------------------------------------------------------------*/
> +#define CONFIG_DU440 1 /* Board is esd DU440 */
> +#define CONFIG_440EPX 1 /* Specific PPC440EPx */
> +#define CONFIG_4xx 1 /* ... PPC4xx family */
> +#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */
> +
> +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
> +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
> +#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */
> +
> +/*-----------------------------------------------------------------------
> + * Base addresses -- Note these are effective addresses where the
> + * actual resources get mapped (not physical addresses)
> + *----------------------------------------------------------------------*/
> +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
> +#define CFG_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
> +
> +#define CFG_BOOT_BASE_ADDR 0xf0000000
> +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
> +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
> +#define CFG_MONITOR_BASE TEXT_BASE
> +#define CFG_NAND0_ADDR 0xd0000000 /* NAND Flash */
> +#define CFG_NAND1_ADDR 0xd0100000 /* NAND Flash */
> +#define CFG_OCM_BASE 0xe0010000 /* ocm */
> +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
> +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
> +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
> +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
> +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
> +#define CFG_PCI_IOBASE 0xe8000000
> +
> +
> +/* Don't change either of these */
> +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
> +
> +#define CFG_USB2D0_BASE 0xe0000100
> +#define CFG_USB_DEVICE 0xe0000000
> +#define CFG_USB_HOST 0xe0000400
> +
> +/*-----------------------------------------------------------------------
> + * Initial RAM & stack pointer
> + *----------------------------------------------------------------------*/
> +/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
> +#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
> +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
> +
> +#define CFG_INIT_RAM_END (4 << 10)
> +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
> +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
> +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
> +
> +/*-----------------------------------------------------------------------
> + * Serial Port
> + *----------------------------------------------------------------------*/
> +/* TODO: external clock oscillator will be removed */
> +#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
> +#define CONFIG_BAUDRATE 115200
> +#define CONFIG_SERIAL_MULTI 1
> +#undef CONFIG_UART1_CONSOLE
> +
> +#define CFG_BAUDRATE_TABLE \
> + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
> +
> +/*-----------------------------------------------------------------------
> + * Video Port
> + *----------------------------------------------------------------------*/
> +#define CONFIG_VIDEO
> +#define CONFIG_VIDEO_SMI_LYNXEM
> +#define CONFIG_CFB_CONSOLE
> +#define CONFIG_VIDEO_LOGO
> +#define CONFIG_VGA_AS_SINGLE_DEVICE
> +#define CONFIG_SPLASH_SCREEN
> +#define CONFIG_SPLASH_SCREEN_ALIGN
> +#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images
> */ +#define CFG_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img
> */ +#define CFG_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
> +#define CFG_CONSOLE_IS_IN_ENV
> +#define CFG_ISA_IO CFG_PCI_IOBASE
> +
> +/*-----------------------------------------------------------------------
> + * Environment
> + *----------------------------------------------------------------------*/
> +#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
> +
> +/*-----------------------------------------------------------------------
> + * FLASH related
> + *----------------------------------------------------------------------*/
> +#define CFG_FLASH_CFI /* The flash is CFI compatible */
> +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
> +
> +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
> +
> +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
> +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
> +
> +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
> +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
> +
> +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x
> faster) */ +/* CFI_FLASH_PROTECTION make flash_protect hang sometimes ->
> disabled */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash
> protection */ +
> +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
> +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
> +
> +#ifdef CFG_ENV_IS_IN_FLASH
> +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
> +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
> +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
> +
> +/* Address and size of Redundant Environment Sector */
> +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
> +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
> +#endif
> +
> +#ifdef CFG_ENV_IS_IN_EEPROM
> +#define CFG_ENV_OFFSET 0 /* environment starts at the beginning of the
> EEPROM */ +#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env
> vars*/ +#endif
> +
> +/*-----------------------------------------------------------------------
> + * DDR SDRAM
> + *----------------------------------------------------------------------*/
> +#define CFG_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
> +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
> +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
> +#if 0
> +#define CONFIG_ZERO_SDRAM /* Zero SDRAM after setup */
> +#endif
> +#define CONFIG_DDR_ECC /* Use ECC when available */
> +#define SPD_EEPROM_ADDRESS {0x50}
> +#define CONFIG_PROG_SDRAM_TLB
> +
> +/*-----------------------------------------------------------------------
> + * I2C
> + *----------------------------------------------------------------------*/
> +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
> +#undef CONFIG_SOFT_I2C /* I2C bit-banged */
> +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
> +#define CFG_I2C_SLAVE 0x7F
> +#define CONFIG_I2C_CMD_TREE 1
> +#define CONFIG_I2C_MULTI_BUS 1
> +
> +#define CFG_SPD_BUS_NUM 0
> +#define IIC1_MCP3021_ADDR 0x4d
> +#define IIC1_USB2507_ADDR 0x2c
> +#ifdef CONFIG_I2C_MULTI_BUS
> +#define CFG_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
> +#endif
> +#define CFG_I2C_MULTI_EEPROMS
> +#define CFG_I2C_EEPROM_ADDR 0x54
> +#define CFG_I2C_EEPROM_ADDR_LEN 2
> +#define CFG_EEPROM_PAGE_WRITE_ENABLE
> +#define CFG_EEPROM_PAGE_WRITE_BITS 5
> +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
> +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
> +
> +#define CFG_EEPROM_WREN 1
> +#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
> +
> +/*
> + * standard dtt sensor configuration - bottom bit will determine local or
> + * remote sensor of the TMP401
> + */
> +#define CONFIG_DTT_SENSORS { 0, 1 }
> +
> +/*
> + * The PMC440 uses a TI TMP401 temperature sensor. This part
> + * is basically compatible to the ADM1021 that is supported
> + * by U-Boot.
> + *
> + * - i2c addr 0x4c
> + * - conversion rate 0x02 = 0.25 conversions/second
> + * - ALERT ouput disabled
> + * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
> + * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
> + */
> +#define CONFIG_DTT_ADM1021
> +#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
> +
> +/*-----------------------------------------------------------------------
> + * RTC stuff
> + *-----------------------------------------------------------------------
> + */
> +#define CONFIG_RTC_DS1338
> +#define CFG_I2C_RTC_ADDR 0x68
> +
> +#undef CONFIG_BOOTARGS
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "netdev=eth0\0" \
> + "ethrotate=no\0" \
> + "hostname=du440\0" \
> + "nfsargs=setenv bootargs root=/dev/nfs rw " \
> + "nfsroot=${serverip}:${rootpath}\0" \
> + "ramargs=setenv bootargs root=/dev/ram rw\0" \
> + "addip=setenv bootargs ${bootargs} " \
> + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
> + ":${hostname}:${netdev}:off panic=1\0" \
> + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
> + "flash_self=run ramargs addip addtty optargs;" \
> + "bootm ${kernel_addr} ${ramdisk_addr}\0" \
> + "net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \
> + "bootm\0" \
> + "rootpath=/tftpboot/du440/target_root_du440\0" \
> + "img=/tftpboot/du440/uImage\0" \
> + "kernel_addr=FFC00000\0" \
> + "ramdisk_addr=FFE00000\0" \
> + "initrd_high=30000000\0" \
> + "load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \
> + "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
> + "cp.b 100000 FFFA0000 60000\0" \
> + ""
> +#if 0
> +#define CONFIG_BOOTCOMMAND "run flash_self"
> +#endif
> +
> +#define CONFIG_PREBOOT /* enable preboot variable */
> +
> +#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
> +
> +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
> +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
> +
> +#ifndef __ASSEMBLY__
> +int du440_phy_addr(int devnum);
> +#endif
> +
> +#define CONFIG_IBM_EMAC4_V4 1
> +#define CONFIG_MII 1 /* MII PHY management */
> +#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address, See
> schematics */ +
> +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
> +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
> +
> +#define CONFIG_HAS_ETH0
> +#define CFG_RX_ETH_BUFFER 128 /* Number of ethernet rx buffers &
> descriptors */ +
> +#define CONFIG_NET_MULTI 1
> +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
> +#define CONFIG_PHY1_ADDR du440_phy_addr(1)
> +
> +/* USB */
> +#define CONFIG_USB_OHCI_NEW
> +#define CONFIG_USB_STORAGE
> +#define CFG_OHCI_BE_CONTROLLER
> +
> +#define CFG_USB_OHCI_CPU_INIT 1
> +#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
> +#define CFG_USB_OHCI_SLOT_NAME "du440"
> +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
> +
> +/* Comment this out to enable USB 1.1 device */
> +#define USB_2_0_DEVICE
> +
> +/* Partitions */
> +#define CONFIG_MAC_PARTITION
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_ISO_PARTITION
> +
> +#include <config_cmd_default.h>
> +
> +#define CONFIG_CMD_BSP
> +#define CONFIG_CMD_DATE
> +#define CONFIG_CMD_ASKENV
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_DTT
> +#define CONFIG_CMD_DIAG
> +#define CONFIG_CMD_EEPROM
> +#define CONFIG_CMD_ELF
> +#define CONFIG_CMD_FAT
> +#define CONFIG_CMD_I2C
> +#define CONFIG_CMD_IRQ
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_NET
> +#define CONFIG_CMD_NFS
> +#define CONFIG_CMD_PCI
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_USB
> +#define CONFIG_CMD_REGINFO
> +#define CONFIG_CMD_SDRAM
> +
> +#define CONFIG_SUPPORT_VFAT
> +
> +/*-----------------------------------------------------------------------
> + * Miscellaneous configurable options
> + *----------------------------------------------------------------------*/
> +#define CFG_LONGHELP /* undef to save memory */
> +#define CFG_PROMPT "=> " /* Monitor Command Prompt */
> +#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
> +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
> +#else
> +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
> +#endif
> +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /*
> Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of
> command args */
> +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
> +
> +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
> +#define CFG_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
> +
> +#define CFG_LOAD_ADDR 0x100000 /* default load address */
> +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
> +
> +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
> +
> +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
> +#define CONFIG_LOOPW 1 /* enable loopw command */
> +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
> +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0
> */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +
> +#define CONFIG_AUTOBOOT_KEYED 1
> +#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d
> seconds\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d"
> +#define CONFIG_AUTOBOOT_STOP_STR " "
> +
> +/*-----------------------------------------------------------------------
> + * PCI stuff
> + *----------------------------------------------------------------------*/
> +/* General PCI */
> +#define CONFIG_PCI /* include pci support */
> +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
> +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
> +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to
> CFG_PCI_MEMBASE*/ +
> +/* Board-specific PCI */
> +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
> +#define CFG_PCI_TARGET_INIT
> +#define CFG_PCI_MASTER_INIT
> +
> +/*
> + * For booting Linux, the board info and command line data
> + * have to be in the first 8 MB of memory, since this is
> + * the maximum mapped by the Linux kernel during initialization.
> + */
> +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
> +
> +/*-----------------------------------------------------------------------
> + * External Bus Controller (EBC) Setup
> + *----------------------------------------------------------------------*/
> +#define CFG_FLASH CFG_FLASH_BASE
> +
> +#define CFG_CPLD_BASE 0xC0000000
> +#define CFG_CPLD_RANGE 0x00000010
> +#define CFG_DUMEM_BASE 0xC0100000
> +#define CFG_DUMEM_RANGE 0x00100000
> +#define CFG_DUIO_BASE 0xC0200000
> +#define CFG_DUIO_RANGE 0x00010000
> +
> +/*
> + * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
> + */
Comment above is not correct. Please fix or remove.
> +#define CFG_NAND0_CS 2 /* NAND chip connected to CSx */
> +#define CFG_NAND1_CS 3 /* NAND chip connected to CSx */
> +/* Memory Bank 0 (NOR-FLASH) initialization */
> +#define CFG_EBC_PB0AP 0x04017200 /* mf test-only - disabled ready# */
> +/* 0x03017200 = 90ns */ /* mf test-only - use 0x04017200 for
> 120ns */ +#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
> +
> +/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
> +#define CFG_EBC_PB1AP 0x018003c0
> +#define CFG_EBC_PB1CR (CFG_CPLD_BASE | 0x18000)
> +
> +/* Memory Bank 2 (NAND-FLASH) initialization */
> +#define CFG_EBC_PB2AP 0x018003c0
> +#define CFG_EBC_PB2CR (CFG_NAND0_ADDR | 0x1c000)
> +
> +/* Memory Bank 3 (NAND-FLASH) initialization */
> +#define CFG_EBC_PB3AP 0x018003c0
> +#define CFG_EBC_PB3CR (CFG_NAND1_ADDR | 0x1c000)
> +
> +/* Memory Bank 4 (DUMEM, 1MB) initialization */
> +#define CFG_EBC_PB4AP 0x018053c0
> +#define CFG_EBC_PB4CR (CFG_DUMEM_BASE | 0x18000)
> +
> +/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum)
> */ +#define CFG_EBC_PB5AP 0x018053c0
> +#define CFG_EBC_PB5CR (CFG_DUIO_BASE | 0x18000)
> +
> +/*-----------------------------------------------------------------------
> + * NAND FLASH
> + *----------------------------------------------------------------------*/
> +#define CFG_MAX_NAND_DEVICE 2
> +#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE
> +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
> +#define CFG_NAND_BASE_LIST {CFG_NAND0_ADDR + CFG_NAND0_CS, CFG_NAND1_ADDR
> + CFG_NAND1_CS} +
> +/*
> + * Internal Definitions
> + *
> + * Boot Flags
> + */
> +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
> +#define BOOTFLAG_WARM 0x02 /* Software reboot */
> +
> +#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
> +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
> +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
> +#endif
> +
> +#if 0
> +#define CONFIG_SHOW_ACTIVITY 1
> +#endif
> +
> +#endif /* __CONFIG_H */
--
Viele Grüße,
Stefan
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
More information about the U-Boot
mailing list