[U-Boot-Users] [PATCH v2 11/12] TQM85xx: NAND support via local bus UPMB
Wolfgang Grandegegr
wg at grandegger.com
Thu Jun 5 13:12:09 CEST 2008
From: Wolfgang Grandegger <wg at grandegger.com>
This patch adds support for NAND FLASH on the TQM8548. It is disabled by
default and can be enabled for the TQM8548 modules. It is now based on
the re-written FSL NAND UPM driver. A patch has been posted earlier today
with the subject:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
Note that the R/B pin is not supported by that module requiring to use
the specified maximum delay time.
Note: With NAND support enabled the size of the U-Boot image exceeds
256 KB and TEXT_BASE must therefore be set to 0xfff80000 in config.mk,
doubling the image size :-(.
Signed-off-by: Thomas Waehner <thomas.waehner at tqs.de>
Signed-off-by: Wolfgang Grandegger <wg at grandegger.com>
---
board/tqc/tqm85xx/Makefile | 8 +-
board/tqc/tqm85xx/law.c | 6 +-
board/tqc/tqm85xx/nand.c | 469 ++++++++++++++++++++++++++++++++++++++++++++
board/tqc/tqm85xx/tlb.c | 2 +-
include/configs/TQM85xx.h | 81 ++++++++-
5 files changed, 558 insertions(+), 8 deletions(-)
create mode 100644 board/tqc/tqm85xx/nand.c
diff --git a/board/tqc/tqm85xx/Makefile b/board/tqc/tqm85xx/Makefile
index 52f5ef9..8ea07f2 100644
--- a/board/tqc/tqm85xx/Makefile
+++ b/board/tqc/tqm85xx/Makefile
@@ -25,8 +25,14 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o sdram.o law.o tlb.o
+COBJS-y += $(BOARD).o
+COBJS-y += sdram.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+COBJS-$(CONFIG_NAND) += nand.o
+
+COBJS := $(COBJS-y)
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
SOBJS := $(addprefix $(obj),$(SOBJS))
diff --git a/board/tqc/tqm85xx/law.c b/board/tqc/tqm85xx/law.c
index bec1ed5..914ce68 100644
--- a/board/tqc/tqm85xx/law.c
+++ b/board/tqc/tqm85xx/law.c
@@ -35,7 +35,7 @@
* 0xc000_0000 0xdfff_ffff RapidIO or PCI express 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
* 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
- * 0xe300_0000 0xe3ff_ffff CAN 16M
+ * 0xe300_0000 0xe3ff_ffff CAN and NAND Flash 16M
* 0xef00_0000 0xefff_ffff PCI express IO 16M
* 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M
*
@@ -54,9 +54,9 @@ struct law_entry law_table[] = {
#else /* !CONFIG_PCIE1 */
SET_LAW_ENTRY (5, CFG_RIO_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_RIO),
#endif /* CONFIG_PCIE1 */
-#ifdef CONFIG_CAN_DRIVER
+#if defined(CONFIG_CAN_DRIVER) || defined(CONFIG_NAND)
SET_LAW_ENTRY (6, CFG_CAN_BASE, LAW_SIZE_16M, LAW_TRGT_IF_LBC),
-#endif /* CONFIG_CAN_DRIVER */
+#endif /* CONFIG_CAN_DRIVER || CONFIG_NAND */
#ifdef CONFIG_PCIE1
SET_LAW_ENTRY (7, CFG_PCIE1_IO_BASE, LAW_SIZE_16M, LAW_TRGT_IF_PCIE_1),
#endif /* CONFIG_PCIE */
diff --git a/board/tqc/tqm85xx/nand.c b/board/tqc/tqm85xx/nand.c
new file mode 100644
index 0000000..fe3b31f
--- /dev/null
+++ b/board/tqc/tqm85xx/nand.c
@@ -0,0 +1,469 @@
+/*
+ * (C) Copyright 2008 Wolfgang Grandegger <wg at denx.de>
+ *
+ * (C) Copyright 2006
+ * Thomas Waehner, TQ-System GmbH, thomas.waehner at tqs.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/fsl_upm.h>
+#include <ioports.h>
+
+#include <nand.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern uint get_lbc_clock (void);
+
+/* index of UPM RAM array run pattern for NAND command cycle */
+#define CFG_NAN_UPM_WRITE_CMD_OFS 0x08
+
+/* index of UPM RAM array run pattern for NAND address cycle */
+#define CFG_NAND_UPM_WRITE_ADDR_OFS 0x10
+
+/* Structure for table with supported UPM timings */
+struct upm_freq {
+ ulong freq;
+ const u32 *upm_patt;
+ uchar gpl4_disable;
+ uchar ehtr;
+ uchar ead;
+};
+
+/* NAND-FLASH UPM tables for TQM85XX according to TQM8548.pq.timing.101.doc */
+
+/* UPM pattern for bus clock = 25 MHz */
+static const u32 upm_patt_25[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff32000, 0x0fa32000, 0x3fb32005, 0xfffffc00,
+ /* 0x04 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff2c30, 0x00ff2c30, 0x0fff2c35, 0xfffffc00,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ec30, 0x00f3ec30, 0x0ff3ec35, 0xfffffc00,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f32c00, 0x00f32c00, 0x0ff32c05, 0xfffffc00,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 33.3 MHz */
+static const u32 upm_patt_33[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff32000, 0x0fa32100, 0x3fb32005, 0xfffffc00,
+ /* 0x04 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff2c30, 0x00ff2c30, 0x0fff2c35, 0xfffffc00,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ec30, 0x00f3ec30, 0x0ff3ec35, 0xfffffc00,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f32c00, 0x00f32c00, 0x0ff32c05, 0xfffffc00,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 41.7 MHz */
+static const u32 upm_patt_42[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff32000, 0x0fa32100, 0x3fb32005, 0xfffffc00,
+ /* 0x04 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff2c30, 0x00ff2c30, 0x0fff2c35, 0xfffffc00,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ec30, 0x00f3ec30, 0x0ff3ec35, 0xfffffc00,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f32c00, 0x00f32c00, 0x0ff32c05, 0xfffffc00,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 50 MHz */
+static const u32 upm_patt_50[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33000, 0x0fa33100, 0x0fa33005, 0xfffffc00,
+ /* 0x04 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3d30, 0x00ff3c30, 0x0fff3c35, 0xfffffc00,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3fd30, 0x00f3fc30, 0x0ff3fc35, 0xfffffc00,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33d00, 0x00f33c00, 0x0ff33c05, 0xfffffc00,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 66.7 MHz */
+static const u32 upm_patt_67[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33000, 0x0fe33000, 0x0fa33100, 0x0fa33000,
+ /* 0x04 */ 0x0fa33005, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3d30, 0x00ff3c30, 0x0fff3c30, 0x0fff3c35,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3fd30, 0x00f3fc30, 0x0ff3fc30, 0x0ff3fc35,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33d00, 0x00f33c00, 0x0ff33c00, 0x0ff33c05,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 83.3 MHz */
+static const u32 upm_patt_83[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33000, 0x0fe33000, 0x0fa33100, 0x0fa33000,
+ /* 0x04 */ 0x0fa33005, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3e30, 0x00ff3c30, 0x0fff3c30, 0x0fff3c35,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3fe30, 0x00f3fc30, 0x0ff3fc30, 0x0ff3fc35,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33e00, 0x00f33c00, 0x0ff33c00, 0x0ff33c05,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 100 MHz */
+static const u32 upm_patt_100[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33100, 0x0fe33000, 0x0fa33200, 0x0fa33000,
+ /* 0x04 */ 0x0fa33005, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3f30, 0x00ff3c30, 0x0fff3c30, 0x0fff3c35,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ff30, 0x00f3fc30, 0x0ff3fc30, 0x0ff3fc35,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33f00, 0x00f33c00, 0x0ff33c00, 0x0ff33c05,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 133.3 MHz */
+static const u32 upm_patt_133[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33100, 0x0fe33000, 0x0fa33300, 0x0fa33000,
+ /* 0x04 */ 0x0fa33000, 0x0fa33005, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3f30, 0x00ff3d30, 0x0fff3d30, 0x0fff3c35,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ff30, 0x00f3fd30, 0x0ff3fd30, 0x0ff3fc35,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33f00, 0x00f33d00, 0x0ff33d00, 0x0ff33c05,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* UPM pattern for bus clock = 166.7 MHz */
+static const u32 upm_patt_167[] = {
+ /* Offset *//* UPM Read Single RAM array entry -> NAND Read Data */
+ /* 0x00 */ 0x0ff33200, 0x0fe33000, 0x0fa33300, 0x0fa33300,
+ /* 0x04 */ 0x0fa33005, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write CMD */
+ /* 0x08 */ 0x00ff3f30, 0x00ff3f30, 0x0fff3e30, 0xffff3c35,
+ /* 0x0C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Read Burst RAM array entry -> NAND Write ADDR */
+ /* 0x10 */ 0x00f3ff30, 0x00f3ff30, 0x0ff3fe30, 0x0ff3fc35,
+ /* 0x14 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Single RAM array entry -> NAND Write Data */
+ /* 0x18 */ 0x00f33f00, 0x00f33f00, 0x0ff33e00, 0x0ff33c05,
+ /* 0x1C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+
+ /* UPM Write Burst RAM array entry -> unused */
+ /* 0x20 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x24 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x28 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x2C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Refresh Timer RAM array entry -> unused */
+ /* 0x30 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x34 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+ /* 0x38 */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+
+ /* UPM Exception RAM array entry -> unsused */
+ /* 0x3C */ 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+};
+
+/* Supported UPM timings */
+struct upm_freq upm_freq_table[] = {
+ /* nominal freq. | ptr to table | GPL4 dis. | EHTR | EAD */
+ {25000000, upm_patt_25, 1, 0, 0},
+ {33333333, upm_patt_33, 1, 0, 0},
+ {41666666, upm_patt_42, 1, 0, 0},
+ {50000000, upm_patt_50, 0, 0, 0},
+ {66666666, upm_patt_67, 0, 0, 0},
+ {83333333, upm_patt_83, 0, 0, 0},
+ {100000000, upm_patt_100, 0, 1, 1},
+ {133333333, upm_patt_133, 0, 1, 1},
+ {166666666, upm_patt_167, 0, 1, 1},
+};
+
+#define UPM_FREQS (sizeof(upm_freq_table) / sizeof(struct upm_freq))
+
+volatile const u32 *nand_upm_patt;
+
+/*
+ * write into UPMB ram
+ */
+static void upmb_write (u_char addr, ulong val)
+{
+ volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);
+
+ out_be32 (&lbc->mdr, val);
+
+ clrsetbits_be32(&lbc->mbmr, MxMR_MAD_MSK,
+ MxMR_OP_WARR | (addr & MxMR_MAD_MSK));
+
+ /* dummy access to perform write */
+ out_8 ((void __iomem *)CFG_NAND0_BASE, 0);
+
+ clrbits_be32(&lbc->mbmr, MxMR_OP_WARR);
+}
+
+/*
+ * Initialize UPM for NAND flash access.
+ */
+static void nand_upm_setup (volatile ccsr_lbc_t *lbc)
+{
+ uint i;
+ uint or3 = CFG_OR3_PRELIM;
+ uint clock = get_lbc_clock ();
+
+ out_be32 (&lbc->br3, 0); /* disable bank and reset all bits */
+ out_be32 (&lbc->br3, CFG_BR3_PRELIM);
+
+ /*
+ * Search appropriate UPM table for bus clock.
+ * If the bus clock exceeds a tolerated value, take the UPM timing for
+ * the next higher supported frequency to ensure that access works
+ * (even the access may be slower then).
+ */
+ for (i = 0; (i < UPM_FREQS) && (clock > upm_freq_table[i].freq); i++)
+ ;
+
+ if (i >= UPM_FREQS)
+ /* no valid entry found */
+ /* take last entry with configuration for max. bus clock */
+ i--;
+
+ if (upm_freq_table[i].ehtr) {
+ /* EHTR must be set due to TQM8548 timing specification */
+ or3 |= OR_UPM_EHTR;
+ }
+ if (upm_freq_table[i].ead)
+ /* EAD must be set due to TQM8548 timing specification */
+ or3 |= OR_UPM_EAD;
+
+ out_be32 (&lbc->or3, or3);
+
+ /* Assign address of table */
+ nand_upm_patt = upm_freq_table[i].upm_patt;
+
+ for (i = 0; i < 64; i++) {
+ upmb_write (i, *nand_upm_patt);
+ nand_upm_patt++;
+ }
+
+ /* Put UPM back to normal operation mode */
+ if (upm_freq_table[i].gpl4_disable)
+ /* GPL4 must be disabled according to timing specification */
+ out_be32 (&lbc->mbmr, MxMR_OP_NORM | MxMR_GPL_x4DIS);
+
+ return;
+}
+
+static struct fsl_upm_nand fun = {
+ .width = 8,
+ .upm_cmd_offset = 0x08,
+ .upm_addr_offset = 0x10,
+ .chip_delay = NAND_BIG_DELAY_US,
+};
+
+void board_nand_select_device (struct nand_chip *nand, int chip)
+{
+}
+
+int board_nand_init (struct nand_chip *nand)
+{
+ volatile ccsr_lbc_t *lbc = (void *)(CFG_MPC85xx_LBC_ADDR);
+
+ if (!nand_upm_patt)
+ nand_upm_setup (lbc);
+
+ fun.upm.io_addr = nand->IO_ADDR_R;
+ fun.upm.mxmr = (void __iomem *)&lbc->mbmr;
+ fun.upm.mdr = (void __iomem *)&lbc->mdr;
+ fun.upm.mar = (void __iomem *)&lbc->mar;
+
+ return fsl_upm_nand_init (nand, &fun);
+}
diff --git a/board/tqc/tqm85xx/tlb.c b/board/tqc/tqm85xx/tlb.c
index 7c4b9a1..7f4efc1 100644
--- a/board/tqc/tqm85xx/tlb.c
+++ b/board/tqc/tqm85xx/tlb.c
@@ -114,7 +114,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
* TLB 6: 64M Non-cacheable, guarded
* 0xe0000000 1M CCSRBAR
* 0xe2000000 16M PCI1 IO
- * 0xe3000000 16M CAN
+ * 0xe3000000 16M CAN and NAND Flash
*/
SET_TLB_ENTRY (1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 2155130..b188adf 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -55,6 +55,14 @@
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
/*
+ * NAND flash support (disabled by default)
+ *
+ * Warning: NAND support will likely increase the U-Boot image size
+ * to more than 256 KB. Please adjust TEXT_BASE if necessary.
+ */
+#undef CONFIG_NAND
+
+/*
* MPC8540 and MPC8548 don't have CPM module
*/
#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548)
@@ -205,8 +213,8 @@
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */
+#define CFG_MALLOC_LEN (384 * 1024) /* Reserved for malloc */
/* Serial Port */
#if defined(CONFIG_TQM8560)
@@ -253,8 +261,8 @@
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* CAN */
-#ifdef CONFIG_CAN_DRIVER
#define CFG_CAN_BASE 0xE3000000 /* CAN base address */
+#ifdef CONFIG_CAN_DRIVER
#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */
#define CFG_OR2_CAN (CFG_CAN_OR_AM | OR_UPM_BI)
#define CFG_BR2_CAN ((CFG_CAN_BASE & BR_BA) | \
@@ -301,6 +309,53 @@
#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
#endif /* CONFIG_PCIE1 */
+/* NAND FLASH */
+#ifdef CONFIG_NAND
+
+#undef CFG_NAND_LEGACY
+
+#define CONFIG_NAND_FSL_UPM 1
+
+#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */
+
+/* address distance between chip selects */
+#define CFG_NAND_SELECT_DEVICE 1
+#define CFG_NAND_CS_DIST 0x200
+
+#define CFG_NAND_SIZE 0x8000
+#define CFG_NAND0_BASE 0xE3010000
+#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST)
+#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST)
+#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST)
+
+#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS 1
+
+#if (CFG_MAX_NAND_DEVICE == 1)
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
+#elif (CFG_MAX_NAND_DEVICE == 2)
+#define CFG_NAND_QUIET_TEST 1
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \
+ CFG_NAND1_BASE, \
+}
+#elif (CFG_MAX_NAND_DEVICE == 4)
+#define CFG_NAND_QUIET_TEST 1
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \
+ CFG_NAND1_BASE, \
+ CFG_NAND2_BASE, \
+ CFG_NAND3_BASE, \
+}
+#endif
+
+/* CS3 for NAND Flash */
+#define CFG_BR3_PRELIM ((CFG_NAND0_BASE & BR_BA) | BR_PS_8 | \
+ BR_MS_UPMB | BR_V)
+#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_NAND_SIZE) | OR_UPM_BI)
+
+#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */
+
+#endif /* CONFIG_NAND */
+
/*
* General PCI
* Addresses are mapped 1-1.
@@ -486,6 +541,26 @@
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
+#ifdef CONFIG_NAND
+/*
+ * Use NAND-FLash as JFFS2 device
+ */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_JFFS2
+
+#define CONFIG_JFFS2_NAND 1
+
+#ifdef CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nand0=TQM85xx-nand"
+#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-"
+#else
+#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */
+#endif /* CONFIG_JFFS2_CMDLINE */
+
+#endif /* CONFIG_NAND */
+
/*
* Command line configuration.
*/
--
1.5.4.2
More information about the U-Boot
mailing list