[U-Boot-Users] [RFC][FSL DDR 6/8] Modify mpc8641HPCN to use the new DDR setup code.
Kumar Gala
galak at kernel.crashing.org
Mon Jun 9 21:55:20 CEST 2008
From: Jon Loeliger <jdl at freescale.com>
Signed-off-by: Jon Loeliger <jdl at freescale.com>
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
Makefile | 3 +
board/freescale/mpc8641hpcn/Makefile | 8 +-
board/freescale/mpc8641hpcn/ddr.c | 288 +++++++++++++++++++++++++++++
board/freescale/mpc8641hpcn/mpc8641hpcn.c | 5 +-
cpu/mpc86xx/Makefile | 1 -
include/configs/MPC8641HPCN.h | 127 ++++++++------
6 files changed, 371 insertions(+), 61 deletions(-)
create mode 100644 board/freescale/mpc8641hpcn/ddr.c
diff --git a/Makefile b/Makefile
index cc988e1..39fc369 100644
--- a/Makefile
+++ b/Makefile
@@ -236,6 +236,9 @@ endif
ifeq ($(CPU),mpc85xx)
LIBS += drivers/qe/qe.a
endif
+ifeq ($(CPU),mpc86xx)
+LIBS += cpu/mpc8xxx/libmpc8xxx.a
+endif
LIBS += drivers/rtc/librtc.a
LIBS += drivers/serial/libserial.a
LIBS += drivers/usb/libusb.a
diff --git a/board/freescale/mpc8641hpcn/Makefile b/board/freescale/mpc8641hpcn/Makefile
index 115df05..bbc64d1 100644
--- a/board/freescale/mpc8641hpcn/Makefile
+++ b/board/freescale/mpc8641hpcn/Makefile
@@ -25,10 +25,12 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o law.o
+COBJS-y += $(BOARD).o
+COBJS-y += law.o
+COBJS-y += ddr.o
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
diff --git a/board/freescale/mpc8641hpcn/ddr.c b/board/freescale/mpc8641hpcn/ddr.c
new file mode 100644
index 0000000..e02d1fd
--- /dev/null
+++ b/board/freescale/mpc8641hpcn/ddr.c
@@ -0,0 +1,288 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <../cpu/mpc8xxx/fsl_ddr_sdram.h>
+
+#define SDRAM_TYPE_DDR1 2
+#define SDRAM_TYPE_DDR2 3
+#define SDRAM_TYPE_LPDDR1 6
+#define SDRAM_TYPE_DDR3 7
+
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+
+unsigned int
+fsl_ddr_sdram_get_mem_data_rate(void)
+{
+ return get_bus_freq(0);
+}
+
+
+void
+fsl_ddr_sdram_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ unsigned int i2c_address = 0;
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (ctrl_num == 0 && i == 0) {
+ i2c_address = SPD_EEPROM_ADDRESS1;
+ }
+ if (ctrl_num == 0 && i == 1) {
+ i2c_address = SPD_EEPROM_ADDRESS2;
+ }
+ if (ctrl_num == 1 && i == 0) {
+ i2c_address = SPD_EEPROM_ADDRESS3;
+ }
+ if (ctrl_num == 1 && i == 1) {
+ i2c_address = SPD_EEPROM_ADDRESS4;
+ }
+ get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ }
+}
+
+
+void
+fsl_ddr_sdram_dump_memctl_regs(unsigned int ctrl_num)
+{
+ unsigned int i;
+ volatile ccsr_ddr_t *ddr;
+
+ if (ctrl_num == 0)
+ ddr = (void *)CFG_MPC86xx_DDR_ADDR;
+ else
+ ddr = (void *)CFG_MPC86xx_DDR2_ADDR;
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ unsigned int bnds = 0;
+ unsigned int config = 0;
+
+ if (i == 0) {
+ bnds = ddr->cs0_bnds;
+ config = ddr->cs0_config;
+
+ } else if (i == 1) {
+ bnds = ddr->cs1_bnds;
+ config = ddr->cs1_config;
+
+ } else if (i == 2) {
+ bnds = ddr->cs2_bnds;
+ config = ddr->cs2_config;
+
+ } else if (i == 3) {
+ bnds = ddr->cs3_bnds;
+ config = ddr->cs3_config;
+
+ } else {
+ /*
+ * FIXME what happens when CONFIG_CHIP_SELECTS_PER_CTRL > 4
+ */
+ }
+
+ printf("cs%u_bnds = %08X\n", i, bnds);
+ printf("cs%u_config = %08X\n", i, config);
+ }
+
+ printf("timing_cfg_3 = %08X\n", ddr->timing_cfg_3);
+ printf("timing_cfg_0 = %08X\n", ddr->timing_cfg_0);
+ printf("timing_cfg_1 = %08X\n", ddr->timing_cfg_1);
+ printf("timing_cfg_2 = %08X\n", ddr->timing_cfg_2);
+ printf("ddr_sdram_cfg = %08X\n", ddr->sdram_cfg_1);
+ printf("ddr_sdram_cfg_2 = %08X\n", ddr->sdram_cfg_2);
+ printf("ddr_sdram_mode = %08X\n", ddr->sdram_mode_1);
+ printf("ddr_sdram_mode_2 = %08X\n", ddr->sdram_mode_2);
+ printf("ddr_sdram_interval = %08X\n", ddr->sdram_interval);
+ printf("ddr_data_init = %08X\n", ddr->sdram_data_init);
+ printf("ddr_sdram_clk_cntl = %08X\n", ddr->sdram_clk_cntl);
+ printf("ddr_init_addr = %08X\n", ddr->init_addr);
+
+// FIXME cleanup
+// printf("timing_cfg_4 = %08X\n", ddr->timing_cfg_4);
+// printf("timing_cfg_5 = %08X\n", ddr->timing_cfg_5);
+// printf("ddr_zq_cntl = %08X\n", ddr->ddr_zq_cntl);
+// printf("ddr_wrlvl_cntl = %08X\n", ddr->ddr_wrlvl_cntl);
+// printf("ddr_pd_cntl = %08X\n", ddr->ddr_pd_cntl);
+// printf("ddr_sr_cntr = %08X\n", ddr->ddr_sr_cntr);
+// printf("ddr_sdram_rcw_1 = %08X\n", ddr->ddr_sdram_rcw_1);
+// printf("ddr_sdram_rcw_2 = %08X\n", ddr->ddr_sdram_rcw_2);
+}
+
+
+void
+fsl_ddr_sdram_set_memctl_regs(const fsl_memctl_config_regs_t *regs,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ volatile ccsr_ddr_t *ddr;
+
+ switch (ctrl_num) {
+ case 0:
+ ddr = (void *)CFG_MPC86xx_DDR_ADDR;
+ break;
+ case 1:
+ ddr = (void *)CFG_MPC86xx_DDR2_ADDR;
+ break;
+ default:
+ printf("fsl_ddr_sdram_set_memctl_regs() unexpected ctrl_num = %u\n", ctrl_num);
+ return;
+ }
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i == 0) {
+ ddr->cs0_bnds = regs->cs[i].bnds;
+ ddr->cs0_config = regs->cs[i].config;
+// ddr->cs0_config_2 = regs->cs[i].config_2;
+
+ } else if (i == 1) {
+ ddr->cs1_bnds = regs->cs[i].bnds;
+ ddr->cs1_config = regs->cs[i].config;
+// ddr->cs1_config_2 = regs->cs[i].config_2;
+
+ } else if (i == 2) {
+ ddr->cs2_bnds = regs->cs[i].bnds;
+ ddr->cs2_config = regs->cs[i].config;
+// ddr->cs2_config_2 = regs->cs[i].config_2;
+
+ } else if (i == 3) {
+ ddr->cs3_bnds = regs->cs[i].bnds;
+ ddr->cs3_config = regs->cs[i].config;
+// ddr->cs3_config_2 = regs->cs[i].config_2;
+ }
+ }
+
+ /*
+ * Someone decided to use different names from the documentation...
+ */
+ ddr->timing_cfg_3 = regs->timing_cfg_3;
+ ddr->timing_cfg_0 = regs->timing_cfg_0;
+ ddr->timing_cfg_1 = regs->timing_cfg_1;
+ ddr->timing_cfg_2 = regs->timing_cfg_2;
+ ddr->sdram_cfg_2 = regs->ddr_sdram_cfg_2;
+ ddr->sdram_mode_1 = regs->ddr_sdram_mode;
+ ddr->sdram_mode_2 = regs->ddr_sdram_mode_2;
+ ddr->sdram_interval = regs->ddr_sdram_interval;
+ ddr->sdram_data_init = regs->ddr_data_init;
+ ddr->sdram_clk_cntl = regs->ddr_sdram_clk_cntl;
+ ddr->init_addr = regs->ddr_init_addr;
+ ddr->init_ext_addr = regs->ddr_init_ext_addr;
+
+
+ /*
+ * FIXME: ECC? Need to program err_disable, err_sbe, and err_int_en
+ */
+#if 0
+ /* 8572 */
+ ddr->timing_cfg_4 = regs->timing_cfg_4;
+ ddr->timing_cfg_5 = regs->timing_cfg_5;
+ ddr->ddr_zq_cntl = regs->ddr_zq_cntl;
+ ddr->ddr_wrlvl_cntl = regs->ddr_wrlvl_cntl;
+ ddr->ddr_pd_cntl = regs->ddr_pd_cntl;
+ ddr->ddr_sr_cntr = regs->ddr_sr_cntr;
+ ddr->ddr_sdram_rcw_1 = regs->ddr_sdram_rcw_1;
+ ddr->ddr_sdram_rcw_2 = regs->ddr_sdram_rcw_2;
+#endif
+
+ printf("before go\n");
+
+ /*
+ * 200 painful micro-seconds must elapse between
+ * the DDR clock setup and the DDR config enable.
+ */
+ udelay(200);
+ asm volatile("sync;isync");
+
+ ddr->sdram_cfg_1 = regs->ddr_sdram_cfg;
+
+
+ /*
+ * Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done
+ */
+ while (ddr->sdram_cfg_2 & 0x10) {
+ udelay(10000); /* throttle polling rate */
+ }
+}
+
+
+unsigned int
+fsl_ddr_sdram_type_function(void)
+{
+ return SDRAM_TYPE_DDR2;
+}
+
+
+/*
+ * factors to consider for clock adjust:
+ * - number of chips on bus
+ * - position of slot
+ * - DDR1 vs. DDR2?
+ * - ???
+ *
+ * FIXME: need to figure out the function parameters necessary to compute
+ * FIXME: a clock adjust value
+ */
+
+unsigned int
+fsl_ddr_sdram_clk_adjust_function(void)
+{
+ return 7;
+}
+
+
+/*
+ * factors to consider for CPO:
+ * - frequency
+ * - ddr1 vs. ddr2
+ *
+ * FIXME: figure out how to compute or tabulate good values for this
+ */
+
+unsigned int
+fsl_ddr_sdram_cpo_override_function(void)
+{
+ return 10;
+}
+
+
+/*
+ * factors to consider for write data delay:
+ * - number of DIMMs
+ *
+ * 1 = 1/4 clock delay
+ * 2 = 1/2 clock delay
+ * 3 = 3/4 clock delay
+ * 4 = 1 clock delay
+ * 5 = 5/4 clock delay
+ * 6 = 3/2 clock delay
+ */
+
+unsigned int
+fsl_ddr_sdram_write_data_delay_function(void)
+{
+ return 3;
+}
+
+
+/*
+ * factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+
+unsigned int
+fsl_ddr_sdram_half_strength_driver_enable_function(void)
+{
+ return 0;
+}
diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c
index bb1f927..755c967 100644
--- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c
+++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c
@@ -25,18 +25,17 @@
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/immap_fsl_pci.h>
-#include <spd_sdram.h>
#include <asm/io.h>
#include <libfdt.h>
#include <fdt_support.h>
#include "../common/pixis.h"
+#include "../cpu/mpc8xxx/fsl_ddr_sdram.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
-void sdram_init(void);
long int fixed_sdram(void);
@@ -59,7 +58,7 @@ initdram(int board_type)
long dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram();
+ dram_size = fsl_ddr_sdram();
#else
dram_size = fixed_sdram();
#endif
diff --git a/cpu/mpc86xx/Makefile b/cpu/mpc86xx/Makefile
index 4227053..454c728 100644
--- a/cpu/mpc86xx/Makefile
+++ b/cpu/mpc86xx/Makefile
@@ -36,7 +36,6 @@ COBJS-y += cpu.o
COBJS-y += cpu_init.o
COBJS-y += speed.o
COBJS-y += interrupts.o
-COBJS-y += spd_sdram.o
COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 49ee7ff..7366b50 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -54,19 +54,6 @@
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#undef CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CONFIG_NUM_DDR_CONTROLLERS 2
-/* #define CONFIG_DDR_INTERLEAVE 1 */
-#define CACHE_LINE_INTERLEAVING 0x20000000
-#define PAGE_INTERLEAVING 0x21000000
-#define BANK_INTERLEAVING 0x22000000
-#define SUPER_BANK_INTERLEAVING 0x23000000
-
#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
#define CONFIG_ALTIVEC 1
@@ -105,53 +92,85 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
/*
* DDR Setup
*/
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#undef CONFIG_DDR_DLL
+
+//#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+//#define CONFIG_DDR_ECC /* only for ECC DDR module */
+
+//#define CONFIG_DDR_INTERLEAVE 1
+//#define CACHE_LINE_INTERLEAVING 0x20000000
+//#define PAGE_INTERLEAVING 0x21000000
+//#define BANK_INTERLEAVING 0x22000000
+//#define SUPER_BANK_INTERLEAVING 0x23000000
+
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
- #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
- #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
- #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
-#else
- /*
- * Manually set up DDR1 parameters
- */
-
- #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
-
- #define CFG_DDR_CS0_BNDS 0x0000000F
- #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
- #define CFG_DDR_EXT_REFRESH 0x00000000
- #define CFG_DDR_TIMING_0 0x00260802
- #define CFG_DDR_TIMING_1 0x39357322
- #define CFG_DDR_TIMING_2 0x14904cc8
- #define CFG_DDR_MODE_1 0x00480432
- #define CFG_DDR_MODE_2 0x00000000
- #define CFG_DDR_INTERVAL 0x06090100
- #define CFG_DDR_DATA_INIT 0xdeadbeef
- #define CFG_DDR_CLK_CTRL 0x03800000
- #define CFG_DDR_OCD_CTRL 0x00000000
- #define CFG_DDR_OCD_STATUS 0x00000000
- #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
- #define CFG_DDR_CONTROL2 0x04400000
-
- /* Not used in fixed_sdram function */
-
- #define CFG_DDR_MODE 0x00000022
- #define CFG_DDR_CS1_BNDS 0x00000000
- #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
- #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
- #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
- #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
-#endif
+/*
+ * Number of memory controllers on device
+ */
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+
+/*
+ * Number of DIMM slots per memory controller
+ */
+#define CONFIG_DIMM_SLOTS_PER_CTLR 2
+
+/*
+ * Number of chip selects per memory controller
+ */
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+/*
+ * I2C addresses of SPD EEPROMs
+ */
+#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
+#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */
+#define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */
+#define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */
+
+
+/*
+ * These are used when DDR doesn't use SPD.
+ */
+#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
+#define CFG_DDR_CS0_BNDS 0x0000000F
+#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_TIMING_0 0x00260802
+#define CFG_DDR_TIMING_1 0x39357322
+#define CFG_DDR_TIMING_2 0x14904cc8
+#define CFG_DDR_MODE_1 0x00480432
+#define CFG_DDR_MODE_2 0x00000000
+#define CFG_DDR_INTERVAL 0x06090100
+#define CFG_DDR_DATA_INIT 0xdeadbeef
+#define CFG_DDR_CLK_CTRL 0x03800000
+#define CFG_DDR_OCD_CTRL 0x00000000
+#define CFG_DDR_OCD_STATUS 0x00000000
+#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
+#define CFG_DDR_CONTROL2 0x04400000
+
+/*
+ * FIXME: Not used in fixed_sdram function
+ */
+#define CFG_DDR_MODE 0x00000022
+#define CFG_DDR_CS1_BNDS 0x00000000
+#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
+#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
+#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
+#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
+
#define CFG_ID_EEPROM 1
#ifdef CFG_ID_EEPROM
--
1.5.5.1
More information about the U-Boot
mailing list