[U-Boot-Users] [PATCH] M18 flash (Sibley) support (attempt 2)

[Vasiliy Leoenenko]

cfi_flash: support of long cmd in U-boot.

Some NOR flash chips needs support of commands with length grether than max value size of uchar.
For example all M18 family chips use 0x1ff command in buffered write mode as value of program loops count.

Signed-off-by: Alexey Korolev <akorolev at infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko at mail.ru>
======================================================
diff -aupNr a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c
--- a/drivers/mtd/cfi_flash.c	2008-04-21 02:39:38.000000000 +0400
+++ b/drivers/mtd/cfi_flash.c	2008-05-07 15:51:18.000000000 +0400
@@ -298,17 +298,25 @@ static inline void flash_unmap(flash_inf
 /*-----------------------------------------------------------------------
  * make a proper sized command based on the port and chip widths
  */
-static void flash_make_cmd (flash_info_t * info, uchar cmd, void *cmdbuf)
+static void flash_make_cmd (flash_info_t * info, ulong cmd, void *cmdbuf)
 {
 	int i;
+	int cword_offset;
+	int cp_offset;
+	uchar val;
 	uchar *cp = (uchar *) cmdbuf;
 
+	for (i = info->portwidth; i > 0; i--){
+		cword_offset = (info->portwidth-i)%info->chipwidth;
 #if defined(__LITTLE_ENDIAN) || defined(CFG_WRITE_SWAPPED_DATA)
-	for (i = info->portwidth; i > 0; i--)
+		cp_offset = info->portwidth - i;
+		val = *((uchar*)&cmd + cword_offset);
 #else
-	for (i = 1; i <= info->portwidth; i++)
+		cp_offset = i - 1;
+		val = *((uchar*)&cmd + sizeof(ulong) - cword_offset - 1);
 #endif
-		*cp++ = (i & (info->chipwidth - 1)) ? '\0' : cmd;
+		cp[cp_offset] = (cword_offset >= sizeof(ulong)) ? 0x00 : val;	
+	}
 }
 
 #ifdef DEBUG
@@ -422,7 +430,7 @@ static ulong flash_read_long (flash_info
  * Write a proper sized command to the correct address
  */
 static void flash_write_cmd (flash_info_t * info, flash_sect_t sect,
-			     uint offset, uchar cmd)
+			     uint offset, ulong cmd)
 {
 
 	void *addr;
@@ -911,7 +919,7 @@ static int flash_write_cfibuffer (flash_
 			/* reduce the number of loops by the width of
 			 * the port */
 			cnt = len >> shift;
-			flash_write_cmd (info, sector, 0, (uchar) cnt - 1);
+			flash_write_cmd (info, sector, 0, cnt - 1);
 			while (cnt-- > 0) {
 				switch (info->portwidth) {
 				case FLASH_CFI_8BIT:
@@ -953,7 +961,7 @@ static int flash_write_cfibuffer (flash_
 #endif
 		flash_write_cmd(info, sector, offset, AMD_CMD_WRITE_TO_BUFFER);
 		cnt = len >> shift;
-		flash_write_cmd(info, sector, offset, (uchar)cnt - 1);
+		flash_write_cmd(info, sector, offset, cnt - 1);
 
 		switch (info->portwidth) {
 		case FLASH_CFI_8BIT: