[U-Boot-Users] [PATCH V5] ARM: Add support for Lyrtech SFF-SDR board (ARM926EJS)
Hugo Villeneuve
hugo.villeneuve at lyrtech.com
Thu May 22 22:09:02 CEST 2008
ARM: This patch adds support for the Lyrtech SFF-SDR
board, based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: Hugo Villeneuve <hugo.villeneuve at lyrtech.com>
Signed-off-by: Philip Balister <philip at balister.org>
---
CREDITS | 4 +
MAKEALL | 1 +
Makefile | 3 +
board/davinci/sffsdr/Makefile | 51 +++++++++
board/davinci/sffsdr/board_init.S | 32 ++++++
board/davinci/sffsdr/config.mk | 42 +++++++
board/davinci/sffsdr/sffsdr.c | 217 +++++++++++++++++++++++++++++++++++++
board/davinci/sffsdr/u-boot.lds | 52 +++++++++
include/asm-arm/mach-types.h | 13 +++
include/configs/davinci_sffsdr.h | 174 +++++++++++++++++++++++++++++
10 files changed, 589 insertions(+), 0 deletions(-)
diff --git a/CREDITS b/CREDITS
index e84ef38..37f55fe 100644
--- a/CREDITS
+++ b/CREDITS
@@ -533,3 +533,7 @@ N: Timo Tuunainen
E: timo.tuunainen at sysart.fi
D: Support for Artila M-501 starter kit
W: http://www.sysart.fi/
+
+N: Philip Balister
+E: philip at balister.org
+D: Port to Lyrtech SFFSDR development board.
diff --git a/MAKEALL b/MAKEALL
index 37b4334..f53ceec 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -496,6 +496,7 @@ LIST_ARM9=" \
voiceblue \
davinci_dvevm \
davinci_schmoogie \
+ davinci_sffsdr \
davinci_sonata \
"
diff --git a/Makefile b/Makefile
index 6548f8e..05d90aa 100644
--- a/Makefile
+++ b/Makefile
@@ -2408,6 +2408,9 @@ davinci_dvevm_config : unconfig
davinci_schmoogie_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs schmoogie davinci davinci
+davinci_sffsdr_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs sffsdr davinci davinci
+
davinci_sonata_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs sonata davinci davinci
diff --git a/board/davinci/sffsdr/Makefile b/board/davinci/sffsdr/Makefile
new file mode 100644
index 0000000..4413b33
--- /dev/null
+++ b/board/davinci/sffsdr/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o
+SOBJS := board_init.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak *~ .depend
+
+#########################################################################
+# This is for $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/davinci/sffsdr/board_init.S b/board/davinci/sffsdr/board_init.S
new file mode 100644
index 0000000..84ecd96
--- /dev/null
+++ b/board/davinci/sffsdr/board_init.S
@@ -0,0 +1,32 @@
+/*
+ * Board-specific low level initialization code. Called at the very end
+ * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no
+ * initialization required.
+ *
+ * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+.globl dv_board_init
+dv_board_init:
+
+ mov pc, lr
diff --git a/board/davinci/sffsdr/config.mk b/board/davinci/sffsdr/config.mk
new file mode 100644
index 0000000..1dde6e2
--- /dev/null
+++ b/board/davinci/sffsdr/config.mk
@@ -0,0 +1,42 @@
+#
+# Lyrtech SFF SDR board (ARM926EJS) cpu
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <gj at denx.de>
+# David Mueller, ELSOFT AG, <d.mueller at elsoft.ch>
+#
+# Copyright (C) 2008 Lyrtech <www.lyrtech.com>
+# Copyright (C) 2008 Philip Balister <philip at balister.org>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+
+#
+# SFF SDR board has 1 bank of 128 MB DDR RAM
+# Physical Address:
+# 8000'0000 to 87FF'FFFF
+#
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+#
+# Integrity kernel is expected to be at 8000'0000, entry 8000'00D0,
+# up to 81FF'FFFF (uses up to 32 MB of memory for text, heap, etc).
+#
+# we load ourself to 8400'0000 to provide at least 32MB spacing
+# between us and the Integrity kernel image
+TEXT_BASE = 0x84000000
diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c
new file mode 100644
index 0000000..80e4f16
--- /dev/null
+++ b/board/davinci/sffsdr/sffsdr.c
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+ *
+ * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
+ * Copyright (C) 2008 Philip Balister <philip at balister.org>
+ *
+ * Parts are shamelessly stolen from various TI sources, original copyright
+ * follows:
+ *
+ * Copyright (C) 2004 Texas Instruments.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/emac_defs.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void timer_init(void);
+extern int eth_hw_init(void);
+extern phy_t phy;
+
+
+/* Works on Always On power domain only (no PD argument) */
+void lpsc_on(unsigned int id)
+{
+ dv_reg_p mdstat, mdctl;
+
+ if (id >= DAVINCI_LPSC_GEM)
+ return; /* Don't work on DSP Power Domain */
+
+ mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4));
+ mdctl = REG_P(PSC_MDCTL_BASE + (id * 4));
+
+ while (REG(PSC_PTSTAT) & 0x01);
+
+ if ((*mdstat & 0x1f) == 0x03)
+ return; /* Already on and enabled */
+
+ *mdctl |= 0x03;
+
+ /* Special treatment for some modules as for sprue14 p.7.4.2 */
+ switch (id) {
+ case DAVINCI_LPSC_VPSSSLV:
+ case DAVINCI_LPSC_EMAC:
+ case DAVINCI_LPSC_EMAC_WRAPPER:
+ case DAVINCI_LPSC_MDIO:
+ case DAVINCI_LPSC_USB:
+ case DAVINCI_LPSC_ATA:
+ case DAVINCI_LPSC_VLYNQ:
+ case DAVINCI_LPSC_UHPI:
+ case DAVINCI_LPSC_DDR_EMIF:
+ case DAVINCI_LPSC_AEMIF:
+ case DAVINCI_LPSC_MMC_SD:
+ case DAVINCI_LPSC_MEMSTICK:
+ case DAVINCI_LPSC_McBSP:
+ case DAVINCI_LPSC_GPIO:
+ *mdctl |= 0x200;
+ break;
+ }
+
+ REG(PSC_PTCMD) = 0x01;
+
+ while (REG(PSC_PTSTAT) & 0x03);
+ while ((*mdstat & 0x1f) != 0x03); /* Probably an overkill... */
+}
+
+void dsp_on(void)
+{
+ int i;
+
+ if (REG(PSC_PDSTAT1) & 0x1f)
+ return; /* Already on */
+
+ REG(PSC_GBLCTL) |= 0x01;
+ REG(PSC_PDCTL1) |= 0x01;
+ REG(PSC_PDCTL1) &= ~0x100;
+ REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03;
+ REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff;
+ REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03;
+ REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff;
+ REG(PSC_PTCMD) = 0x02;
+
+ for (i = 0; i < 100; i++) {
+ if (REG(PSC_EPCPR) & 0x02)
+ break;
+ }
+
+ REG(PSC_CHP_SHRTSW) = 0x01;
+ REG(PSC_PDCTL1) |= 0x100;
+ REG(PSC_EPCCR) = 0x02;
+
+ for (i = 0; i < 100; i++) {
+ if (!(REG(PSC_PTSTAT) & 0x02))
+ break;
+ }
+
+ REG(PSC_GBLCTL) &= ~0x1f;
+}
+
+int board_init(void)
+{
+ /* arch number of the board */
+ gd->bd->bi_arch_number = MACH_TYPE_SFFSDR;
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
+
+ /* Workaround for TMS320DM6446 errata 1.3.22 */
+ REG(PSC_SILVER_BULLET) = 0;
+
+ /* Power on required peripherals */
+ lpsc_on(DAVINCI_LPSC_EMAC);
+ lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
+ lpsc_on(DAVINCI_LPSC_MDIO);
+ lpsc_on(DAVINCI_LPSC_I2C);
+ lpsc_on(DAVINCI_LPSC_UART0);
+ lpsc_on(DAVINCI_LPSC_TIMER1);
+ lpsc_on(DAVINCI_LPSC_GPIO);
+
+ /* Powerup the DSP */
+ dsp_on();
+
+ /* Bringup UART0 out of reset */
+ REG(UART0_PWREMU_MGMT) = 0x0000e003;
+
+ /* Enable GIO3.3V cells used for EMAC */
+ REG(VDD3P3V_PWDN) = 0;
+
+ /* Enable UART0 MUX lines */
+ REG(PINMUX1) |= 1;
+
+ /* Enable EMAC and AEMIF pins */
+ REG(PINMUX0) = 0x80000c1f;
+
+ /* Enable I2C pin Mux */
+ REG(PINMUX1) |= (1 << 7);
+
+ /* Set the Bus Priority Register to appropriate value */
+ REG(VBPR) = 0x20;
+
+ timer_init();
+
+ return(0);
+}
+
+int misc_init_r(void)
+{
+ u_int8_t tmp[20], buf[10];
+ int i = 0;
+ int clk = 0;
+
+ clk = ((REG(PLL2_PLLM) + 1) * 27) / ((REG(PLL2_DIV2) & 0x1f) + 1);
+
+ printf("ARM Clock: %dMHz\n", ((REG(PLL1_PLLM) + 1) * 27) / 2);
+ printf("DDR Clock: %dMHz\n", (clk / 2));
+
+ /* Configure I2C switch (PCA9543) to enable channel 0. */
+ tmp[0] = CFG_I2C_PCA9543_ENABLE_CH0;
+ if (i2c_write(CFG_I2C_PCA9543_ADDR, 0,
+ CFG_I2C_PCA9543_ADDR_LEN, tmp, 1))
+ printf("Write to MUX @ 0x%02x failed\n", CFG_I2C_PCA9543_ADDR);
+
+ /* Set Ethernet MAC address from EEPROM.
+ * We must read 8 bytes because data is stored in little-endian. */
+ if (i2c_read(CFG_I2C_EEPROM_ADDR, 0x05A8,
+ CFG_I2C_EEPROM_ADDR_LEN, buf, 8)) {
+ printf("Read from EEPROM @ 0x%02x failed\n",
+ CFG_I2C_EEPROM_ADDR);
+ } else {
+ tmp[0] = 0xff;
+ for (i = 0; i < 6; i++)
+ tmp[0] &= buf[i];
+
+ if ((tmp[0] != 0xff) && (getenv("ethaddr") == NULL)) {
+ sprintf((char *)&tmp[0],
+ "%02x:%02x:%02x:%02x:%02x:%02x",
+ buf[3], buf[2], buf[1], buf[0],
+ buf[7], buf[6]);
+ setenv("ethaddr", (char *)&tmp[0]);
+ }
+ }
+
+ if (!eth_hw_init()) {
+ printf("Ethernet init failed\n");
+ } else {
+ printf("ETH PHY: %s\n", phy.name);
+ }
+
+ return(0);
+}
+
+int dram_init(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+ return(0);
+}
diff --git a/board/davinci/sffsdr/u-boot.lds b/board/davinci/sffsdr/u-boot.lds
new file mode 100644
index 0000000..a4fcd1a
--- /dev/null
+++ b/board/davinci/sffsdr/u-boot.lds
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj at denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/arm926ejs/start.o (.text)
+ *(.text)
+ }
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+ . = ALIGN(4);
+ .data : { *(.data) }
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss (NOLOAD) : { *(.bss) }
+ _end = .;
+}
diff --git a/include/asm-arm/mach-types.h b/include/asm-arm/mach-types.h
index aaf2ea2..b347857 100644
--- a/include/asm-arm/mach-types.h
+++ b/include/asm-arm/mach-types.h
@@ -1595,6 +1595,7 @@ extern unsigned int __machine_arch_type;
#define MACH_TYPE_P300 1602
#define MACH_TYPE_XDACOMET 1603
#define MACH_TYPE_DEXFLEX2 1604
+#define MACH_TYPE_SFFSDR 1657
#ifdef CONFIG_ARCH_EBSA110
# ifdef machine_arch_type
@@ -16500,6 +16501,18 @@ extern unsigned int __machine_arch_type;
# define machine_is_schmoogie() (0)
#endif
+#ifdef CONFIG_MACH_SFFSDR
+# ifdef machine_arch_type
+# undef machine_arch_type
+# define machine_arch_type __machine_arch_type
+# else
+# define machine_arch_type MACH_TYPE_SFFSDR
+# endif
+# define machine_is_sffsdr() (machine_arch_type == MACH_TYPE_SFFSDR)
+#else
+# define machine_is_sffsdr() (0)
+#endif
+
#ifdef CONFIG_MACH_AZTOOL
# ifdef machine_arch_type
# undef machine_arch_type
diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
new file mode 100644
index 0000000..9f90576
--- /dev/null
+++ b/include/configs/davinci_sffsdr.h
@@ -0,0 +1,174 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+ *
+ * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
+ * Copyright (C) 2008 Philip Balister <philip at balister.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*=======*/
+/* Board */
+/*=======*/
+#define SFFSDR
+#define CFG_NAND_LARGEPAGE
+#define CFG_USE_NAND
+/*===================*/
+/* SoC Configuration */
+/*===================*/
+#define CONFIG_ARM926EJS /* arm926ejs CPU core */
+#define CONFIG_SYS_CLK_FREQ 297000000 /* Arm Clock frequency */
+#define CFG_TIMERBASE 0x01c21400 /* use timer 0 */
+#define CFG_HZ_CLOCK 27000000 /* Timer Input clock freq */
+#define CFG_HZ 1000
+/*==================================================*/
+/* EEPROM definitions for Atmel 24LC64 EEPROM chip */
+/*==================================================*/
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_EEPROM_PAGE_WRITE_BITS 5
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+/*=============*/
+/* Memory Info */
+/*=============*/
+#define CFG_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
+#define CFG_GBL_DATA_SIZE 128 /* reserved for initial data */
+#define CFG_MEMTEST_START 0x80000000 /* memtest start address */
+#define CFG_MEMTEST_END 0x81000000 /* 16MB RAM test */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
+#define CONFIG_STACKSIZE (256*1024) /* regular stack */
+#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
+#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
+/*====================*/
+/* Serial Driver info */
+/*====================*/
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 4 /* NS16550 register size */
+#define CFG_NS16550_COM1 0x01c20000 /* Base address of UART0 */
+#define CFG_NS16550_CLK 27000000 /* Input clock to NS16550 */
+#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
+#define CONFIG_BAUDRATE 115200 /* Default baud rate */
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+/*===================*/
+/* I2C Configuration */
+/*===================*/
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CFG_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
+#define CFG_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
+/*==================================*/
+/* Network & Ethernet Configuration */
+/*==================================*/
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+/*=====================*/
+/* Flash & Environment */
+/*=====================*/
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_NO_FLASH
+#define CFG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
+#define CFG_ENV_SECT_SIZE 2048 /* Env sector Size */
+#define CFG_ENV_SIZE SZ_128K
+#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
+#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
+#define CFG_NAND_BASE 0x02000000
+#define CFG_NAND_HW_ECC
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS 1
+#define CFG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
+/*=====================*/
+/* Board related stuff */
+/*=====================*/
+/*==========================================*/
+/* I2C switch definitions for PCA9543 chip */
+/* on Lyrtech SFF SDR board. */
+/* This chip has a single register. */
+/*==========================================*/
+#define CFG_I2C_PCA9543_ADDR 0x70
+#define CFG_I2C_PCA9543_ADDR_LEN 0
+#define CFG_I2C_PCA9543_ENABLE_CH0 0x01 /* Enable channel 0. */
+/*==============================*/
+/* U-Boot general configuration */
+/*==============================*/
+#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */
+#define CONFIG_MISC_INIT_R
+#undef CONFIG_BOOTDELAY
+#define CONFIG_BOOTFILE "uImage" /* Boot file name */
+#define CFG_PROMPT "U-Boot > " /* Monitor Command Prompt */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+/* Print buffer size */
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR 0x80700000 /* Default Linux kernel
+ * load address. */
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far,
+ * may be later */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_CMDLINE_EDITING
+#define CFG_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/*===================*/
+/* Linux Information */
+/*===================*/
+#define LINUX_BOOT_PARAM_ADDR 0x80000100
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTARGS \
+ "mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
+
+/*=================*/
+/* U-Boot commands */
+/*=================*/
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_EEPROM
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+/*=======================*/
+/* KGDB support (if any) */
+/*=======================*/
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
More information about the U-Boot
mailing list