[U-Boot-Users] [PATCH] TQM85xx: Various coding style fixes

Wolfgang Grandegger wg at grandegger.com
Wed May 28 20:12:19 CEST 2008


Signed-off-by: Wolfgang Grandegger <wg at grandegger.com>
---
 board/tqc/tqm85xx/law.c     |   12 +-
 board/tqc/tqm85xx/sdram.c   |   56 ++++----
 board/tqc/tqm85xx/tlb.c     |   98 +++++++------
 board/tqc/tqm85xx/tqm85xx.c |  330 +++++++++++++++++++++---------------------
 include/configs/TQM85xx.h   |   88 ++++++------
 5 files changed, 293 insertions(+), 291 deletions(-)

diff --git a/board/tqc/tqm85xx/law.c b/board/tqc/tqm85xx/law.c
index 224af6c..d937700 100644
--- a/board/tqc/tqm85xx/law.c
+++ b/board/tqc/tqm85xx/law.c
@@ -44,11 +44,11 @@
  */
 
 struct law_entry law_table[] = {
-	SET_LAW_ENTRY(1, CFG_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR),
-	SET_LAW_ENTRY(2, CFG_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
-	SET_LAW_ENTRY(3, CFG_LBC_FLASH_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
-	SET_LAW_ENTRY(4, CFG_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
-	SET_LAW_ENTRY(5, CFG_RIO_MEM_BASE, LAWAR_SIZE_512M, LAW_TRGT_IF_RIO),
+	SET_LAW_ENTRY (1, CFG_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR),
+	SET_LAW_ENTRY (2, CFG_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
+	SET_LAW_ENTRY (3, CFG_LBC_FLASH_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
+	SET_LAW_ENTRY (4, CFG_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
+	SET_LAW_ENTRY (5, CFG_RIO_MEM_BASE, LAWAR_SIZE_512M, LAW_TRGT_IF_RIO),
 };
 
-int num_law_entries = ARRAY_SIZE(law_table);
+int num_law_entries = ARRAY_SIZE (law_table);
diff --git a/board/tqc/tqm85xx/sdram.c b/board/tqc/tqm85xx/sdram.c
index 788a48c..413567e 100644
--- a/board/tqc/tqm85xx/sdram.c
+++ b/board/tqc/tqm85xx/sdram.c
@@ -21,7 +21,6 @@
  * MA 02111-1307 USA
  */
 
-
 #include <common.h>
 #include <asm/processor.h>
 #include <asm/immap_85xx.h>
@@ -39,12 +38,12 @@ sdram_conf_t ddr_cs_conf[] = {
 	{(512 << 20), 0x80000202},	/* 512MB, 14x10(4)	*/
 	{(256 << 20), 0x80000102},	/* 256MB, 13x10(4)	*/
 	{(128 << 20), 0x80000101},	/* 128MB, 13x9(4)	*/
-	{(64  << 20), 0x80000001},	/* 64MB,  12x9(4)	*/
+	{( 64 << 20), 0x80000001},	/*  64MB, 12x9(4)	*/
 };
 
 #define	N_DDR_CS_CONF (sizeof(ddr_cs_conf) / sizeof(ddr_cs_conf[0]))
 
-int cas_latency(void);
+int cas_latency (void);
 
 /*
  * Autodetect onboard DDR SDRAM on 85xx platforms
@@ -53,7 +52,7 @@ int cas_latency(void);
  *       so this should be extended for other future boards
  *       using this routine!
  */
-long int sdram_setup(int casl)
+long int sdram_setup (int casl)
 {
 	int i;
 	volatile ccsr_ddr_t *ddr = (void *)(CFG_MPC85xx_DDR_ADDR);
@@ -92,17 +91,18 @@ long int sdram_setup(int casl)
 	ddr->sdram_interval = 0x05160100;	/* autocharge,no open page */
 	ddr->err_disable = 0x0000000D;
 
-	asm ("sync;isync;msync");
-	udelay(1000);
+	asm ("sync; isync; msync");
+	udelay (1000);
 
 	ddr->sdram_cfg = 0xc2000000;		/* unbuffered,no DYN_PWR */
 	asm ("sync; isync; msync");
-	udelay(1000);
+	udelay (1000);
 
-	for (i=0; i<N_DDR_CS_CONF; i++) {
+	for (i = 0; i < N_DDR_CS_CONF; i++) {
 		ddr->cs0_config = ddr_cs_conf[i].reg;
 
-		if (get_ram_size(0, ddr_cs_conf[i].size) == ddr_cs_conf[i].size) {
+		if (get_ram_size (0, ddr_cs_conf[i].size) ==
+		    ddr_cs_conf[i].size) {
 			/*
 			 * OK, size detected -> all done
 			 */
@@ -110,30 +110,30 @@ long int sdram_setup(int casl)
 		}
 	}
 
-	return 0;				/* nothing found !		*/
+	return 0;		/* nothing found !              */
 }
 
-void board_add_ram_info(int use_default)
+void board_add_ram_info (int use_default)
 {
 	int casl;
 
 	if (use_default)
 		casl = CONFIG_DDR_DEFAULT_CL;
 	else
-		casl = cas_latency();
+		casl = cas_latency ();
 
-	puts(" (CL=");
+	puts (" (CL=");
 	switch (casl) {
 	case 20:
-		puts("2)");
+		puts ("2)");
 		break;
 
 	case 25:
-		puts("2.5)");
+		puts ("2.5)");
 		break;
 
 	case 30:
-		puts("3)");
+		puts ("3)");
 		break;
 	}
 }
@@ -149,7 +149,7 @@ long int initdram (int board_type)
 	 */
 	{
 		volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
-		int i,x;
+		int i, x;
 
 		x = 10;
 
@@ -157,32 +157,32 @@ long int initdram (int board_type)
 		 * Work around to stabilize DDR DLL
 		 */
 		gur->ddrdllcr = 0x81000000;
-		asm("sync;isync;msync");
+		asm ("sync; isync; msync");
 		udelay (200);
 		while (gur->ddrdllcr != 0x81000100) {
 			gur->devdisr = gur->devdisr | 0x00010000;
-			asm("sync;isync;msync");
-			for (i=0; i<x; i++)
+			asm ("sync; isync; msync");
+			for (i = 0; i < x; i++)
 				;
 			gur->devdisr = gur->devdisr & 0xfff7ffff;
-			asm("sync;isync;msync");
+			asm ("sync; isync; msync");
 			x++;
 		}
 	}
 #endif
 
-	casl = cas_latency();
-	dram_size = sdram_setup(casl);
+	casl = cas_latency ();
+	dram_size = sdram_setup (casl);
 	if ((dram_size == 0) && (casl != CONFIG_DDR_DEFAULT_CL)) {
 		/*
 		 * Try again with default CAS latency
 		 */
-		puts("Problem with CAS lantency");
-		board_add_ram_info(1);
-		puts(", using default CL!\n");
+		puts ("Problem with CAS lantency");
+		board_add_ram_info (1);
+		puts (", using default CL!\n");
 		casl = CONFIG_DDR_DEFAULT_CL;
-		dram_size = sdram_setup(casl);
-		puts("       ");
+		dram_size = sdram_setup (casl);
+		puts ("       ");
 	}
 
 	return dram_size;
diff --git a/board/tqc/tqm85xx/tlb.c b/board/tqc/tqm85xx/tlb.c
index ad26cae..3e29062 100644
--- a/board/tqc/tqm85xx/tlb.c
+++ b/board/tqc/tqm85xx/tlb.c
@@ -28,87 +28,93 @@
 
 struct fsl_e_tlb_entry tlb_table[] = {
 	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 4 * 1024 , CFG_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 8 * 1024 , CFG_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CFG_INIT_RAM_ADDR + 12 * 1024 , CFG_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
+	SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR, CFG_INIT_RAM_ADDR,
+		       MAS3_SX | MAS3_SW | MAS3_SR, 0,
+		       0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 4 * 1024,
+		       CFG_INIT_RAM_ADDR + 4 * 1024,
+		       MAS3_SX | MAS3_SW | MAS3_SR, 0,
+		       0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 8 * 1024,
+		       CFG_INIT_RAM_ADDR + 8 * 1024,
+		       MAS3_SX | MAS3_SW | MAS3_SR, 0,
+		       0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY (0, CFG_INIT_RAM_ADDR + 12 * 1024,
+		       CFG_INIT_RAM_ADDR + 12 * 1024,
+		       MAS3_SX | MAS3_SW | MAS3_SR, 0,
+		       0, 0, BOOKE_PAGESZ_4K, 0),
 
 	/*
 	 * TLB 0, 1:	128M	Non-cacheable, guarded
 	 * 0xf8000000	128M	FLASH
 	 * Out of reset this entry is only 4K.
 	 */
-	SET_TLB_ENTRY(1, CFG_FLASH_BASE, CFG_FLASH_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_64M, 1),
-	SET_TLB_ENTRY(1, CFG_FLASH_BASE + 0x4000000, CFG_FLASH_BASE + 0x4000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_64M, 1),
+	SET_TLB_ENTRY (1, CFG_FLASH_BASE, CFG_FLASH_BASE,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 1, BOOKE_PAGESZ_64M, 1),
+	SET_TLB_ENTRY (1, CFG_FLASH_BASE + 0x4000000,
+		       CFG_FLASH_BASE + 0x4000000,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 0, BOOKE_PAGESZ_64M, 1),
 
 	/*
 	 * TLB 2:	256M	Non-cacheable, guarded
 	 * 0x80000000	256M	PCI1 MEM First half
 	 */
-	SET_TLB_ENTRY(1, CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_PHYS,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 2, BOOKE_PAGESZ_256M, 1),
 
 	/*
 	 * TLB 3:	256M	Non-cacheable, guarded
 	 * 0x90000000	256M	PCI1 MEM Second half
 	 */
-	SET_TLB_ENTRY(1, CFG_PCI1_MEM_PHYS + 0x10000000, CFG_PCI1_MEM_PHYS + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_PCI1_MEM_PHYS + 0x10000000,
+		       CFG_PCI1_MEM_PHYS + 0x10000000,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 3, BOOKE_PAGESZ_256M, 1),
 
 	/*
 	 * TLB 4:	256M	Non-cacheable, guarded
 	 * 0xc0000000	256M	Rapid IO MEM First half
 	 */
-	SET_TLB_ENTRY(1, CFG_RIO_MEM_BASE, CFG_RIO_MEM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_RIO_MEM_BASE, CFG_RIO_MEM_BASE,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 4, BOOKE_PAGESZ_256M, 1),
 
 	/*
 	 * TLB 5:	256M	Non-cacheable, guarded
 	 * 0xd0000000	256M	Rapid IO MEM Second half
 	 */
-	SET_TLB_ENTRY(1, CFG_RIO_MEM_BASE + 0x10000000, CFG_RIO_MEM_BASE + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_RIO_MEM_BASE + 0x10000000,
+		       CFG_RIO_MEM_BASE + 0x10000000,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 5, BOOKE_PAGESZ_256M, 1),
 
 	/*
-	 * TLB 6:	64M	Non-cacheable, guarded
-	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	16M	PCI1 IO
+	 * TLB 6:	 64M	Non-cacheable, guarded
+	 * 0xe0000000	  1M	CCSRBAR
+	 * 0xe2000000	 16M	PCI1 IO
 	 */
-	SET_TLB_ENTRY(1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 6, BOOKE_PAGESZ_64M, 1),
+	SET_TLB_ENTRY (1, CFG_CCSRBAR, CFG_CCSRBAR_PHYS,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 6, BOOKE_PAGESZ_64M, 1),
 
 	/*
-	 * TLB 7+8:	512M	DDR, cache disabled (needed for memory test)
-	 * 0x00000000  512M	DDR System memory
+	 * TLB 7+8:	512M	 DDR, cache disabled (needed for memory test)
+	 * 0x00000000	512M	 DDR System memory
 	 * Without SPD EEPROM configured DDR, this must be setup manually.
 	 * Make sure the TLB count at the top of this table is correct.
 	 * Likely it needs to be increased by two for these entries.
 	 */
-	SET_TLB_ENTRY(1, CFG_DDR_SDRAM_BASE, CFG_DDR_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 7, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_DDR_SDRAM_BASE, CFG_DDR_SDRAM_BASE,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 7, BOOKE_PAGESZ_256M, 1),
 
-	SET_TLB_ENTRY(1, CFG_DDR_SDRAM_BASE + 0x10000000, CFG_DDR_SDRAM_BASE + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 8, BOOKE_PAGESZ_256M, 1),
+	SET_TLB_ENTRY (1, CFG_DDR_SDRAM_BASE + 0x10000000,
+		       CFG_DDR_SDRAM_BASE + 0x10000000,
+		       MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+		       0, 8, BOOKE_PAGESZ_256M, 1),
 };
 
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+int num_tlb_entries = ARRAY_SIZE (tlb_table);
diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c
index 8fa0162..31364d3 100644
--- a/board/tqc/tqm85xx/tqm85xx.c
+++ b/board/tqc/tqm85xx/tqm85xx.c
@@ -42,7 +42,7 @@ void local_bus_init (void);
 ulong flash_get_size (ulong base, int banknum);
 
 #ifdef CONFIG_PS2MULT
-void ps2mult_early_init(void);
+void ps2mult_early_init (void);
 #endif
 
 #ifdef CONFIG_CPM2
@@ -55,149 +55,149 @@ void ps2mult_early_init(void);
 
 const iop_conf_t iop_conf_tab[4][32] = {
 
-    /* Port A configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PA31 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII COL */
-	/* PA30 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII CRS */
-	/* PA29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_ER */
-	/* PA28 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_EN */
-	/* PA27 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_DV */
-	/* PA26 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_ER */
-	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
-	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
-	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
-	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
-	/* PA21 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[3] */
-	/* PA20 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[2] */
-	/* PA19 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[1] */
-	/* PA18 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[0] */
-	/* PA17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[0] */
-	/* PA16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[1] */
-	/* PA15 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[2] */
-	/* PA14 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[3] */
-	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
-	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
-	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
-	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
-	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
-	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
-	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
-	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
-	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
-	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
-	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
-	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
-	/* PA1  */ {   0,   0,   0,   0,   0,   0   }, /* FREERUN */
-	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
-    },
-
-    /* Port B configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
-	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
-	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
-	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
-	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
-	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
-	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
-	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
-	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
-	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
-	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
-	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
-	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
-	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
-	/* PB17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
-	/* PB16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
-	/* PB15 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
-	/* PB14 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
-	/* PB13 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:COL */
-	/* PB12 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
-	/* PB11 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB10 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB9  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB8  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB7  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB6  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB5  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB4  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    },
-
-    /* Port C */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
-	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
-	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
-	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
-	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
-	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
-	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
-	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
-	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
-	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
-	/* PC21 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
-	/* PC20 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
-	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
-	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
-	/* PC17 */ {   1,   1,   0,   0,   0,   0   }, /* PC17 */
-	/* PC16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
-	/* PC15 */ {   0,   1,   0,   0,   0,   0   }, /* PC15 */
-	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
-	/* PC13 */ {   0,   1,   0,   0,   0,   0   }, /* PC13 */
-	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
-	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
-	/* PC10 */ {   0,   0,   0,   1,   0,   0   }, /* FETHMDC */
-	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FETHMDIO */
-	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
-	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
-	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
-	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
-	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
-	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
-	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
-	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
-	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
-    },
-
-    /* Port D */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PD31 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
-	/* PD30 */ {   1,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
-	/* PD29 */ {   1,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
-	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* PD28 */
-	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* PD27 */
-	/* PD26 */ {   1,   1,   0,   1,   0,   0   }, /* PD26 */
-	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
-	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
-	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
-	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
-	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
-	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
-	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
-	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
-	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
-	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-	/* PD15 */ {   0,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   0,   0,   0,   1,   0,   0   }, /* LED */
-	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
-	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
-	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
-	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
-	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
-	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
-	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
-	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
-	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
-	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
-	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    }
+	/* Port A: conf, ppar, psor, pdir, podr, pdat */
+	{
+	 {1, 1, 1, 0, 0, 0},	/* PA31: FCC1 MII COL */
+	 {1, 1, 1, 0, 0, 0},	/* PA30: FCC1 MII CRS */
+	 {1, 1, 1, 1, 0, 0},	/* PA29: FCC1 MII TX_ER */
+	 {1, 1, 1, 1, 0, 0},	/* PA28: FCC1 MII TX_EN */
+	 {1, 1, 1, 0, 0, 0},	/* PA27: FCC1 MII RX_DV */
+	 {1, 1, 1, 0, 0, 0},	/* PA26: FCC1 MII RX_ER */
+	 {0, 1, 0, 1, 0, 0},	/* PA25: FCC1 ATMTXD[0] */
+	 {0, 1, 0, 1, 0, 0},	/* PA24: FCC1 ATMTXD[1] */
+	 {0, 1, 0, 1, 0, 0},	/* PA23: FCC1 ATMTXD[2] */
+	 {0, 1, 0, 1, 0, 0},	/* PA22: FCC1 ATMTXD[3] */
+	 {1, 1, 0, 1, 0, 0},	/* PA21: FCC1 MII TxD[3] */
+	 {1, 1, 0, 1, 0, 0},	/* PA20: FCC1 MII TxD[2] */
+	 {1, 1, 0, 1, 0, 0},	/* PA19: FCC1 MII TxD[1] */
+	 {1, 1, 0, 1, 0, 0},	/* PA18: FCC1 MII TxD[0] */
+	 {1, 1, 0, 0, 0, 0},	/* PA17: FCC1 MII RxD[0] */
+	 {1, 1, 0, 0, 0, 0},	/* PA16: FCC1 MII RxD[1] */
+	 {1, 1, 0, 0, 0, 0},	/* PA15: FCC1 MII RxD[2] */
+	 {1, 1, 0, 0, 0, 0},	/* PA14: FCC1 MII RxD[3] */
+	 {0, 1, 0, 0, 0, 0},	/* PA13: FCC1 ATMRXD[3] */
+	 {0, 1, 0, 0, 0, 0},	/* PA12: FCC1 ATMRXD[2] */
+	 {0, 1, 0, 0, 0, 0},	/* PA11: FCC1 ATMRXD[1] */
+	 {0, 1, 0, 0, 0, 0},	/* PA10: FCC1 ATMRXD[0] */
+	 {0, 1, 1, 1, 0, 0},	/* PA9 : FCC1 L1TXD */
+	 {0, 1, 1, 0, 0, 0},	/* PA8 : FCC1 L1RXD */
+	 {0, 0, 0, 1, 0, 0},	/* PA7 : PA7 */
+	 {0, 1, 1, 1, 0, 0},	/* PA6 : TDM A1 L1RSYNC */
+	 {0, 0, 0, 1, 0, 0},	/* PA5 : PA5 */
+	 {0, 0, 0, 1, 0, 0},	/* PA4 : PA4 */
+	 {0, 0, 0, 1, 0, 0},	/* PA3 : PA3 */
+	 {0, 0, 0, 1, 0, 0},	/* PA2 : PA2 */
+	 {0, 0, 0, 0, 0, 0},	/* PA1 : FREERUN */
+	 {0, 0, 0, 1, 0, 0}	/* PA0 : PA0 */
+	 },
+
+	/* Port B: conf, ppar, psor, pdir, podr, pdat */
+	{
+	 {1, 1, 0, 1, 0, 0},	/* PB31: FCC2 MII TX_ER */
+	 {1, 1, 0, 0, 0, 0},	/* PB30: FCC2 MII RX_DV */
+	 {1, 1, 1, 1, 0, 0},	/* PB29: FCC2 MII TX_EN */
+	 {1, 1, 0, 0, 0, 0},	/* PB28: FCC2 MII RX_ER */
+	 {1, 1, 0, 0, 0, 0},	/* PB27: FCC2 MII COL */
+	 {1, 1, 0, 0, 0, 0},	/* PB26: FCC2 MII CRS */
+	 {1, 1, 0, 1, 0, 0},	/* PB25: FCC2 MII TxD[3] */
+	 {1, 1, 0, 1, 0, 0},	/* PB24: FCC2 MII TxD[2] */
+	 {1, 1, 0, 1, 0, 0},	/* PB23: FCC2 MII TxD[1] */
+	 {1, 1, 0, 1, 0, 0},	/* PB22: FCC2 MII TxD[0] */
+	 {1, 1, 0, 0, 0, 0},	/* PB21: FCC2 MII RxD[0] */
+	 {1, 1, 0, 0, 0, 0},	/* PB20: FCC2 MII RxD[1] */
+	 {1, 1, 0, 0, 0, 0},	/* PB19: FCC2 MII RxD[2] */
+	 {1, 1, 0, 0, 0, 0},	/* PB18: FCC2 MII RxD[3] */
+	 {1, 1, 0, 0, 0, 0},	/* PB17: FCC3:RX_DIV */
+	 {1, 1, 0, 0, 0, 0},	/* PB16: FCC3:RX_ERR */
+	 {1, 1, 0, 1, 0, 0},	/* PB15: FCC3:TX_ERR */
+	 {1, 1, 0, 1, 0, 0},	/* PB14: FCC3:TX_EN */
+	 {1, 1, 0, 0, 0, 0},	/* PB13: FCC3:COL */
+	 {1, 1, 0, 0, 0, 0},	/* PB12: FCC3:CRS */
+	 {1, 1, 0, 0, 0, 0},	/* PB11: FCC3:RXD */
+	 {1, 1, 0, 0, 0, 0},	/* PB10: FCC3:RXD */
+	 {1, 1, 0, 0, 0, 0},	/* PB9 : FCC3:RXD */
+	 {1, 1, 0, 0, 0, 0},	/* PB8 : FCC3:RXD */
+	 {1, 1, 0, 1, 0, 0},	/* PB7 : FCC3:TXD */
+	 {1, 1, 0, 1, 0, 0},	/* PB6 : FCC3:TXD */
+	 {1, 1, 0, 1, 0, 0},	/* PB5 : FCC3:TXD */
+	 {1, 1, 0, 1, 0, 0},	/* PB4 : FCC3:TXD */
+	 {0, 0, 0, 0, 0, 0},	/* PB3 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0},	/* PB2 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0},	/* PB1 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0}	/* PB0 : pin doesn't exist */
+	 },
+
+	/* Port C: conf, ppar, psor, pdir, podr, pdat */
+	{
+	 {0, 0, 0, 1, 0, 0},	/* PC31: PC31 */
+	 {0, 0, 0, 1, 0, 0},	/* PC30: PC30 */
+	 {0, 1, 1, 0, 0, 0},	/* PC29: SCC1 EN *CLSN */
+	 {0, 0, 0, 1, 0, 0},	/* PC28: PC28 */
+	 {0, 0, 0, 1, 0, 0},	/* PC27: UART Clock in */
+	 {0, 0, 0, 1, 0, 0},	/* PC26: PC26 */
+	 {0, 0, 0, 1, 0, 0},	/* PC25: PC25 */
+	 {0, 0, 0, 1, 0, 0},	/* PC24: PC24 */
+	 {0, 1, 0, 1, 0, 0},	/* PC23: ATMTFCLK */
+	 {0, 1, 0, 0, 0, 0},	/* PC22: ATMRFCLK */
+	 {1, 1, 0, 0, 0, 0},	/* PC21: SCC1 EN RXCLK */
+	 {1, 1, 0, 0, 0, 0},	/* PC20: SCC1 EN TXCLK */
+	 {1, 1, 0, 0, 0, 0},	/* PC19: FCC2 MII RX_CLK CLK13 */
+	 {1, 1, 0, 0, 0, 0},	/* PC18: FCC Tx Clock (CLK14) */
+	 {1, 1, 0, 0, 0, 0},	/* PC17: PC17 */
+	 {1, 1, 0, 0, 0, 0},	/* PC16: FCC Tx Clock (CLK16) */
+	 {0, 1, 0, 0, 0, 0},	/* PC15: PC15 */
+	 {0, 1, 0, 0, 0, 0},	/* PC14: SCC1 EN *CD */
+	 {0, 1, 0, 0, 0, 0},	/* PC13: PC13 */
+	 {0, 1, 0, 1, 0, 0},	/* PC12: PC12 */
+	 {0, 0, 0, 1, 0, 0},	/* PC11: LXT971 transmit control */
+	 {0, 0, 0, 1, 0, 0},	/* PC10: FETHMDC */
+	 {0, 0, 0, 0, 0, 0},	/* PC9 : FETHMDIO */
+	 {0, 0, 0, 1, 0, 0},	/* PC8 : PC8 */
+	 {0, 0, 0, 1, 0, 0},	/* PC7 : PC7 */
+	 {0, 0, 0, 1, 0, 0},	/* PC6 : PC6 */
+	 {0, 0, 0, 1, 0, 0},	/* PC5 : PC5 */
+	 {0, 0, 0, 1, 0, 0},	/* PC4 : PC4 */
+	 {0, 0, 0, 1, 0, 0},	/* PC3 : PC3 */
+	 {0, 0, 0, 1, 0, 1},	/* PC2 : ENET FDE */
+	 {0, 0, 0, 1, 0, 0},	/* PC1 : ENET DSQE */
+	 {0, 0, 0, 1, 0, 0},	/* PC0 : ENET LBK */
+	 },
+
+	/* Port D: conf, ppar, psor, pdir, podr, pdat */
+	{
+	 {1, 1, 0, 0, 0, 0},	/* PD31: SCC1 EN RxD */
+	 {1, 1, 1, 1, 0, 0},	/* PD30: SCC1 EN TxD */
+	 {1, 1, 0, 1, 0, 0},	/* PD29: SCC1 EN TENA */
+	 {1, 1, 0, 0, 0, 0},	/* PD28: PD28 */
+	 {1, 1, 0, 1, 0, 0},	/* PD27: PD27 */
+	 {1, 1, 0, 1, 0, 0},	/* PD26: PD26 */
+	 {0, 0, 0, 1, 0, 0},	/* PD25: PD25 */
+	 {0, 0, 0, 1, 0, 0},	/* PD24: PD24 */
+	 {0, 0, 0, 1, 0, 0},	/* PD23: PD23 */
+	 {0, 0, 0, 1, 0, 0},	/* PD22: PD22 */
+	 {0, 0, 0, 1, 0, 0},	/* PD21: PD21 */
+	 {0, 0, 0, 1, 0, 0},	/* PD20: PD20 */
+	 {0, 0, 0, 1, 0, 0},	/* PD19: PD19 */
+	 {0, 0, 0, 1, 0, 0},	/* PD18: PD18 */
+	 {0, 1, 0, 0, 0, 0},	/* PD17: FCC1 ATMRXPRTY */
+	 {0, 1, 0, 1, 0, 0},	/* PD16: FCC1 ATMTXPRTY */
+	 {0, 1, 1, 0, 1, 0},	/* PD15: I2C SDA */
+	 {0, 0, 0, 1, 0, 0},	/* PD14: LED */
+	 {0, 0, 0, 0, 0, 0},	/* PD13: PD13 */
+	 {0, 0, 0, 0, 0, 0},	/* PD12: PD12 */
+	 {0, 0, 0, 0, 0, 0},	/* PD11: PD11 */
+	 {0, 0, 0, 0, 0, 0},	/* PD10: PD10 */
+	 {0, 1, 0, 1, 0, 0},	/* PD9 : SMC1 TXD */
+	 {0, 1, 0, 0, 0, 0},	/* PD8 : SMC1 RXD */
+	 {0, 0, 0, 1, 0, 1},	/* PD7 : PD7 */
+	 {0, 0, 0, 1, 0, 1},	/* PD6 : PD6 */
+	 {0, 0, 0, 1, 0, 1},	/* PD5 : PD5 */
+	 {0, 0, 0, 1, 0, 1},	/* PD4 : PD4 */
+	 {0, 0, 0, 0, 0, 0},	/* PD3 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0},	/* PD2 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0},	/* PD1 : pin doesn't exist */
+	 {0, 0, 0, 0, 0, 0}	/* PD0 : pin doesn't exist */
+	 }
 };
 #endif /*  CONFIG_CPM2 */
 
@@ -207,9 +207,9 @@ const iop_conf_t iop_conf_tab[4][32] = {
 static const int casl_table[] = { 20, 25, 30 };
 #define	N_CASL (sizeof(casl_table) / sizeof(casl_table[0]))
 
-int cas_latency(void)
+int cas_latency (void)
 {
-	char *s = getenv("serial#");
+	char *s = getenv ("serial#");
 	int casl;
 	int val;
 	int i;
@@ -217,11 +217,11 @@ int cas_latency(void)
 	casl = CONFIG_DDR_DEFAULT_CL;
 
 	if (s != NULL) {
-		if (strncmp(s + strlen(s) - strlen(CASL_STRING1), CASL_STRING2,
-			    strlen(CASL_STRING2)) == 0) {
-			val = simple_strtoul(s + strlen(s) - 2, NULL, 10);
+		if (strncmp(s + strlen (s) - strlen (CASL_STRING1),
+			    CASL_STRING2, strlen (CASL_STRING2)) == 0) {
+			val = simple_strtoul (s + strlen (s) - 2, NULL, 10);
 
-			for (i=0; i<N_CASL; ++i) {
+			for (i = 0; i < N_CASL; ++i) {
 				if (val == casl_table[i]) {
 					return val;
 				}
@@ -234,14 +234,14 @@ int cas_latency(void)
 
 int checkboard (void)
 {
-	char *s = getenv("serial#");
+	char *s = getenv ("serial#");
 
-	printf("Board: %s", CONFIG_BOARDNAME);
+	printf ("Board: %s", CONFIG_BOARDNAME);
 	if (s != NULL) {
-		puts(", serial# ");
-		puts(s);
+		puts (", serial# ");
+		puts (s);
 	}
-	putc('\n');
+	putc ('\n');
 
 #ifdef CONFIG_PCI
 	printf ("PCI1:  32 bit, %d MHz (compiled)\n",
@@ -272,13 +272,15 @@ int misc_init_r (void)
 	 * Check if boot FLASH isn't max size
 	 */
 	if (gd->bd->bi_flashsize < (0 - CFG_FLASH0)) {
-		memctl->or0 = gd->bd->bi_flashstart | (CFG_OR0_PRELIM & 0x00007fff);
-		memctl->br0 = gd->bd->bi_flashstart | (CFG_BR0_PRELIM & 0x00007fff);
+		memctl->or0 =
+		    gd->bd->bi_flashstart | (CFG_OR0_PRELIM & 0x00007fff);
+		memctl->br0 =
+		    gd->bd->bi_flashstart | (CFG_BR0_PRELIM & 0x00007fff);
 
 		/*
 		 * Re-check to get correct base address
 		 */
-		flash_get_size(gd->bd->bi_flashstart, CFG_MAX_FLASH_BANKS - 1);
+		flash_get_size (gd->bd->bi_flashstart, CFG_MAX_FLASH_BANKS - 1);
 	}
 
 	/*
@@ -297,7 +299,8 @@ int misc_init_r (void)
 
 		/* Monitor protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
-			       CFG_MONITOR_BASE, CFG_MONITOR_BASE + monitor_flash_len - 1,
+			       CFG_MONITOR_BASE,
+			       CFG_MONITOR_BASE + monitor_flash_len - 1,
 			       &flash_info[CFG_MAX_FLASH_BANKS - 1]);
 
 		/* Environment protection ON by default */
@@ -385,22 +388,19 @@ static struct pci_config_table pci_mpc85xxads_config_table[] = {
 	 PCI_IDSEL_NUMBER, PCI_ANY_ID,
 	 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
 				     PCI_ENET0_MEMADDR,
-				     PCI_COMMAND_MEMORY |
-				     PCI_COMMAND_MASTER}},
+				     PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER}},
 	{}
 };
 #endif
 
-
 static struct pci_controller hose = {
 #ifndef CONFIG_PCI_PNP
-	config_table:pci_mpc85xxads_config_table,
+      config_table:pci_mpc85xxads_config_table,
 #endif
 };
 
 #endif /* CONFIG_PCI */
 
-
 void pci_init_board (void)
 {
 #ifdef CONFIG_PCI
@@ -412,7 +412,7 @@ void pci_init_board (void)
 int board_early_init_r (void)
 {
 #ifdef CONFIG_PS2MULT
-	ps2mult_early_init();
+	ps2mult_early_init ();
 #endif /* CONFIG_PS2MULT */
 	return (0);
 }
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index fca5f74..f0e7318 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -50,7 +50,7 @@
 #define CONFIG_CPM2		1	/* has CPM2			*/
 #endif
 
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code	*/
 
 /*
  * sysclk for MPC85xx
@@ -102,11 +102,11 @@
 /* TQM8540 & 8560 need DLL-override */
 #define CONFIG_DDR_DLL				/* DLL fix needed	*/
 #define CONFIG_DDR_DEFAULT_CL	25		/* CAS latency 2,5	*/
-#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */
+#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */
 
 #if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555)
 #define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*/
-#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */
+#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 */
 
 /*
  * Flash on the Local Bus
@@ -116,51 +116,51 @@
 #define CFG_FLASH_BANKS_LIST	{ CFG_FLASH1, CFG_FLASH0 }
 
 #define CFG_LBC_FLASH_BASE	CFG_FLASH1	/* Localbus flash start	*/
-#define CFG_FLASH_BASE		CFG_LBC_FLASH_BASE /* start of FLASH	*/
+#define CFG_FLASH_BASE		CFG_LBC_FLASH_BASE  /* start of FLASH	*/
 
 #define CFG_BR0_PRELIM		0xfc001801	/* port size 32bit	*/
 #define CFG_OR0_PRELIM		0xfc000040	/* 64MB Flash		*/
 #define CFG_BR1_PRELIM		0xf8001801	/* port size 32bit	*/
 #define CFG_OR1_PRELIM		0xfc000040	/* 64MB Flash		*/
 
-#define CFG_FLASH_CFI				/* flash is CFI compat.	*/
-#define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver*/
+#define CFG_FLASH_CFI			/* flash is CFI compat.		*/
+#define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector	*/
 #define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash*/
 
-#define CFG_MAX_FLASH_BANKS	2		/* number of banks	*/
-#define CFG_MAX_FLASH_SECT	512		/* sectors per device	*/
+#define CFG_MAX_FLASH_BANKS	2	/* number of banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* sectors per device		*/
 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms)	*/
 
 #define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor	*/
 
-#define CFG_LBC_LCRR		0x00030008    /* LB clock ratio reg	*/
-#define CFG_LBC_LBCR		0x00000000    /* LB config reg		*/
-#define CFG_LBC_LSRT		0x20000000    /* LB sdram refresh timer	*/
-#define CFG_LBC_MRTPR		0x20000000    /* LB refresh timer presc.*/
+#define CFG_LBC_LCRR		0x00030008	/* LB clock ratio reg	*/
+#define CFG_LBC_LBCR		0x00000000	/* LB config reg	*/
+#define CFG_LBC_LSRT		0x20000000	/* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x20000000	/* LB refresh timer presc.*/
 
 #define CONFIG_L1_INIT_RAM
 #define CFG_INIT_RAM_LOCK	1
 #define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address	*/
 #define CFG_INIT_RAM_END	0x4000		/* End used area in RAM	*/
 
-#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data*/
+#define CFG_GBL_DATA_SIZE	128	/* num bytes initial data	*/
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256kB for Mon*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256kB for Mon */
 #define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc	*/
 
 /* Serial Port */
 #if defined(CONFIG_TQM8560)
 
-#define CONFIG_CONS_ON_SCC      /* define if console on SCC */
-#undef  CONFIG_CONS_NONE        /* define if console on something else */
-#define CONFIG_CONS_INDEX       1  /* which serial channel for console */
+#define CONFIG_CONS_ON_SCC	/* define if console on SCC		*/
+#undef	CONFIG_CONS_NONE	/* define if console on something else	*/
+#define CONFIG_CONS_INDEX	1 /* which serial channel for console	*/
 
-#else	/* ! TQM8560 */
+#else /* !CONFIG_TQM8560 */
 
 #define CONFIG_CONS_INDEX     1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
@@ -173,20 +173,18 @@
 #define CFG_NS16550_COM2	(CFG_CCSRBAR+0x4600)
 
 /* PS/2 Keyboard */
-#if !defined(CONFIG_TQM8560)
 #define CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
 #define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
 #define CONFIG_PS2SERIAL	2	/* .. on DUART2			*/
 #define CONFIG_PS2MULT_DELAY	(CFG_HZ/2)	/* Initial delay	*/
 #define CONFIG_BOARD_EARLY_INIT_R	1
-#endif /* !CONFIG_TQM8560 */
 
 #endif /* CONFIG_TQM8560 */
 
-#define CONFIG_BAUDRATE         115200
+#define CONFIG_BAUDRATE		115200
 
-#define CFG_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CFG_HUSH_PARSER		1	/* Use the HUSH parser		*/
@@ -194,11 +192,10 @@
 #define	CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-
 /*
  * I2C
  */
-#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_FSL_I2C			/* Use FSL common I2C driver	*/
 #define CONFIG_HARD_I2C			/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
@@ -219,7 +216,7 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write	*/
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	20
-#define CFG_I2C_MULTI_EEPROMS		1       /* more than one eeprom */
+#define CFG_I2C_MULTI_EEPROMS		1	/* more than one eeprom	*/
 
 /* I2C SYSMON (LM75) */
 #define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
@@ -242,7 +239,7 @@
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M			*/
 #define CFG_PCI1_IO_BASE	0xe2000000
 #define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M			*/
+#define CFG_PCI1_IO_SIZE	0x1000000	/*  16M			*/
 
 #if defined(CONFIG_PCI)
 
@@ -254,8 +251,7 @@
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
 #define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola			*/
 
-#endif	/* CONFIG_PCI */
-
+#endif /* CONFIG_PCI */
 
 #define CONFIG_NET_MULTI	1
 
@@ -305,7 +301,7 @@
  * FCC2: a - c (X50.2 - 1)
  */
 #define CONFIG_ETHER_ON_FCC
-#define	CONFIG_ETHER_INDEX    1		/* FCC channel for ethernet	*/
+#define	CONFIG_ETHER_INDEX    1	/* FCC channel for ethernet	*/
 #endif
 
 #if defined(CONFIG_TQM8560)
@@ -321,12 +317,13 @@
  * FCC3: a - d (X50.2 - 3)
  */
 #define CONFIG_ETHER_ON_FCC
-#define	CONFIG_ETHER_INDEX    3		/* FCC channel for ethernet	*/
+#define	CONFIG_ETHER_INDEX    3	/* FCC channel for ethernet	*/
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
 #define CONFIG_ETHER_ON_FCC1
-#define CFG_CMXFCR_MASK1	(CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+#define CFG_CMXFCR_MASK1	(CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \
+				 CMXFCR_TF1CS_MSK)
 #define CFG_CMXFCR_VALUE1	(CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
 #define CFG_CPMFCR_RAMTYPE	0
 #define CFG_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
@@ -334,7 +331,8 @@
 
 #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
 #define CONFIG_ETHER_ON_FCC2
-#define CFG_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+#define CFG_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \
+				 CMXFCR_TF2CS_MSK)
 #define CFG_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13)
 #define CFG_CPMFCR_RAMTYPE	0
 #define CFG_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
@@ -342,7 +340,8 @@
 
 #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
 #define CONFIG_ETHER_ON_FCC3
-#define CFG_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+#define CFG_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \
+				 CMXFCR_TF3CS_MSK)
 #define CFG_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
 #define CFG_CPMFCR_RAMTYPE	0
 #define CFG_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
@@ -353,7 +352,7 @@
  */
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x20000)
-#define CFG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env	*/
+#define CFG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env	*/
 #define CFG_ENV_SIZE		0x2000
 #define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
@@ -361,8 +360,7 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define	CONFIG_TIMESTAMP		/* Print image info with ts	*/
-
+#define	CONFIG_TIMESTAMP	/* Print image info with ts	*/
 
 /*
  * BOOTP options
@@ -372,7 +370,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -389,10 +386,9 @@
 #define CONFIG_CMD_MII
 
 #if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI
 #endif
 
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 /*
@@ -403,12 +399,13 @@
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 
 #if defined(CONFIG_CMD_KGDB)
-    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-    #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size	*/
+#define CFG_PBSIZE	(CFG_CBSIZE + \
+			 sizeof(CFG_PROMPT) + 16)   /* Print Buf Size	*/
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 #define CFG_HZ		1000		/* decrementer freq: 1ms ticks	*/
@@ -433,7 +430,6 @@
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
 #endif
 
-
 #define CONFIG_LOADADDR	 200000		/* default addr for tftp & bootm*/
 
 #define CONFIG_BOOTDELAY 5		/* -1 disables auto-boot	*/
@@ -467,10 +463,10 @@
 	"ramdisk_addr=FE180000\0"					\
 	"load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0"		\
 	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
+		"cp.b 100000 fffc0000 40000;"				\
 		"setenv filesize;saveenv\0"				\
 	"upd=run load update\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#endif	/* __CONFIG_H */
+#endif /* __CONFIG_H */
-- 
1.5.2.2





More information about the U-Boot mailing list