[U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31

[Shinya Kuribayashi]

Ping. Please consider making this into the upcoming release.

Jean-Christophe PLAGNIOL-VILLARD wrote:
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
> 
> diff --git a/README.imx31 b/README.imx31
> deleted file mode 100644
> index f545f01..0000000
> --- a/README.imx31
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -i.MX31 specific Configuration Options:
> ---------------------------------------
> -
> -- Timer precision:
> -		CONFIG_MX31_TIMER_HIGH_PRECISION
> -
> -		Enable higher precision timer. The low-precision timer
> -		(default) provides approximately 4% error, whereas the
> -		high-precision timer is about 0.4% accurate. The extra
> -		accuracy is achieved at the cost of higher computational
> -		overhead, which, in places where time is measured, should
> -		not be critical, so, it should be safe to enable this
> -		option.
> diff --git a/doc/README.imx31 b/doc/README.imx31
> new file mode 100644
> index 0000000..91ef766
> --- /dev/null
> +++ b/doc/README.imx31
> @@ -0,0 +1,29 @@
> +U-Boot for Freescale i.MX31
> +
> +This file contains information for the port of U-Boot to the Freescale
> +i.MX31 SoC.
> +
> +1. CONFIGURATION OPTIONS/SETTINGS
> +---------------------------------
> +
> +1.1 Configuration of MC13783 SPI bus
> +------------------------------------
> +	The power management companion chip MC13783 is connected to the
> +	i.MX31 via an SPI bus. Use the following configuration options
> +	to setup the bus and chip select used for a particular board.
> +
> +	CONFIG_MC13783_SPI_BUS	-- defines the SPI bus the MC13783 is connected to.
> +			   Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> +	CONFIG_MC13783_SPI_CS	-- define the chip select the MC13783 s connected to.
> +
> +1.2 Timer precision
> +-------------------
> +	CONFIG_MX31_TIMER_HIGH_PRECISION
> +
> +	Enable higher precision timer. The low-precision timer
> +	(default) provides approximately 4% error, whereas the
> +	high-precision timer is about 0.4% accurate. The extra
> +	accuracy is achieved at the cost of higher computational
> +	overhead, which, in places where time is measured, should
> +	not be critical, so, it should be safe to enable this
> +	option.
> diff --git a/doc/README.mx31 b/doc/README.mx31
> deleted file mode 100644
> index 291c2f3..0000000
> --- a/doc/README.mx31
> +++ /dev/null
> @@ -1,17 +0,0 @@
> -U-Boot for Freescale i.MX31
> -
> -This file contains information for the port of U-Boot to the Freescale
> -i.MX31 SoC.
> -
> -1. CONFIGURATION OPTIONS/SETTINGS
> ----------------------------------
> -
> -1.1 Configuration of MC13783 SPI bus
> -------------------------------------
> -The power management companion chip MC13783 is connected to the
> -i.MX31 via an SPI bus. Use the following configuration options
> -to setup the bus and chip select used for a particular board.
> -
> -CONFIG_MC13783_SPI_BUS	-- defines the SPI bus the MC13783 is connected to.
> -			   Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> -CONFIG_MC13783_SPI_CS	-- define the chip select the MC13783 s connected to.