[U-Boot] [PATCH] OMAP3: Beagle: Set pinmux conditionally for Rev C boards

[Jean-Christophe PLAGNIOL-VILLARD]

On 08:46 Sun 05 Apr     , Dirk Behme wrote:
> The Beagle Rev C boards pull UART2 from an alternate set of balls.
> 
> Signed-off-by: Steve Sakoman <steve at sakoman.com>
> Signed-off-by: Dirk Behme <dirk.behme at googlemail.com>
> ---
> 
>  board/omap3/beagle/beagle.c |    4 ++++
>  board/omap3/beagle/beagle.h |   25 +++++++++++++++++--------
>  2 files changed, 21 insertions(+), 8 deletions(-)
> 
> Index: u-boot-main/board/omap3/beagle/beagle.c
> ===================================================================
> --- u-boot-main.orig/board/omap3/beagle/beagle.c
> +++ u-boot-main/board/omap3/beagle/beagle.c
> @@ -130,4 +130,8 @@ int misc_init_r(void)
>  void set_muxconf_regs(void)
>  {
>  	MUX_BEAGLE();
> +
> +	if(beagle_revision_c) {
please add a space between the if and '('
> +		MUX_BEAGLE_C();
> +	}
>  }
> Index: u-boot-main/board/omap3/beagle/beagle.h
> ===================================================================
> --- u-boot-main.orig/board/omap3/beagle/beagle.h
> +++ u-boot-main/board/omap3/beagle/beagle.h
> @@ -214,14 +214,14 @@ const omap3_sysinfo sysinfo = {
>   MUX_VAL(CP(MMC2_DAT6),		(IEN  | PTU | EN  | M4)) /*GPIO_138*/\
>   MUX_VAL(CP(MMC2_DAT7),		(IEN  | PTU | EN  | M4)) /*GPIO_139*/\
>   /*Bluetooth*/\
> - MUX_VAL(CP(MCBSP3_DX),		(IDIS | PTD | DIS | M4)) /*GPIO_140*/\
> - MUX_VAL(CP(MCBSP3_DR),		(IDIS | PTD | DIS | M4)) /*GPIO_142*/\
> - MUX_VAL(CP(MCBSP3_CLKX),	(IDIS | PTD | DIS | M4)) /*GPIO_141*/\
> - MUX_VAL(CP(MCBSP3_FSX),	(IDIS | PTD | DIS | M4)) /*GPIO_143*/\
<snip>
> +#define MUX_BEAGLE_C() \
> + MUX_VAL(CP(MCBSP3_DX),		(IDIS | PTD | DIS | M4)) /*GPIO_140*/\
> + MUX_VAL(CP(MCBSP3_DR),		(IDIS | PTD | DIS | M4)) /*GPIO_142*/\
> + MUX_VAL(CP(MCBSP3_CLKX),	(IDIS | PTD | DIS | M4)) /*GPIO_141*/\
> + MUX_VAL(CP(UART2_CTS),		(IEN  | PTU | EN  | M0)) /*UART2_CTS*/\
> + MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
> + MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M0)) /*UART2_TX*/
please wait Tom Rix gpio patch move to this API

Best Regards,
J.