[U-Boot] [PATCH 6/7] net: Remove old Xilinx Emac driver
monstr at monstr.eu
monstr at monstr.eu
Thu Aug 20 22:52:30 CEST 2009
From: Michal Simek <monstr at monstr.eu>
Signed-off-by: Michal Simek <monstr at monstr.eu>
Signed-off-by: Michal Simek <michal.simek at petalogix.com>
---
drivers/net/Makefile | 1 -
drivers/net/xilinx_emac.c | 464 ----------------------------------
include/configs/microblaze-generic.h | 5 +-
3 files changed, 1 insertions(+), 469 deletions(-)
delete mode 100644 drivers/net/xilinx_emac.c
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 98cb3a1..4fd53f9 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -72,7 +72,6 @@ COBJS-$(CONFIG_TSEC_ENET) += tsec.o
COBJS-$(CONFIG_TSI108_ETH) += tsi108_eth.o
COBJS-$(CONFIG_ULI526X) += uli526x.o
COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o
-COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o
COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
COBJS-$(CONFIG_XILINX_LL_TEMAC) += xilinx_ll_temac.o
diff --git a/drivers/net/xilinx_emac.c b/drivers/net/xilinx_emac.c
deleted file mode 100644
index a489aa9..0000000
--- a/drivers/net/xilinx_emac.c
+++ /dev/null
@@ -1,464 +0,0 @@
-/******************************************************************************
- *
- * XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
- * AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
- * SOLUTIONS FOR XILINX DEVICES. BY PROVIDING THIS DESIGN, CODE,
- * OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
- * APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
- * THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
- * AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
- * FOR YOUR IMPLEMENTATION. XILINX EXPRESSLY DISCLAIMS ANY
- * WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
- * IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
- * REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
- * INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
- * FOR A PARTICULAR PURPOSE.
- *
- * (C) Copyright 2007-2008 Michal Simek
- * Michal SIMEK <monstr at monstr.eu>
- *
- * (c) Copyright 2003 Xilinx Inc.
- * All rights reserved.
- *
- ******************************************************************************/
-
-#include <config.h>
-#include <common.h>
-#include <net.h>
-#include <asm/io.h>
-
-#include <asm/asm.h>
-
-#undef DEBUG
-
-typedef struct {
- u32 regbaseaddress; /* Base address of registers */
- u32 databaseaddress; /* Base address of data for FIFOs */
-} xpacketfifov100b;
-
-typedef struct {
- u32 baseaddress; /* Base address (of IPIF) */
- u32 isstarted; /* Device is currently started 0-no, 1-yes */
- xpacketfifov100b recvfifo; /* FIFO used to receive frames */
- xpacketfifov100b sendfifo; /* FIFO used to send frames */
-} xemac;
-
-#define XIIF_V123B_IISR_OFFSET 32UL /* IP interrupt status register */
-#define XIIF_V123B_RESET_MASK 0xAUL
-#define XIIF_V123B_RESETR_OFFSET 64UL /* reset register */
-
-/* This constant is used with the Reset Register */
-#define XPF_RESET_FIFO_MASK 0x0000000A
-#define XPF_COUNT_STATUS_REG_OFFSET 4UL
-
-/* These constants are used with the Occupancy/Vacancy Count Register. This
- * register also contains FIFO status */
-#define XPF_COUNT_MASK 0x0000FFFF
-#define XPF_DEADLOCK_MASK 0x20000000
-
-/* Offset of the MAC registers from the IPIF base address */
-#define XEM_REG_OFFSET 0x1100UL
-
-/*
- * Register offsets for the Ethernet MAC. Each register is 32 bits.
- */
-#define XEM_ECR_OFFSET (XEM_REG_OFFSET + 0x4) /* MAC Control */
-#define XEM_SAH_OFFSET (XEM_REG_OFFSET + 0xC) /* Station addr, high */
-#define XEM_SAL_OFFSET (XEM_REG_OFFSET + 0x10) /* Station addr, low */
-#define XEM_RPLR_OFFSET (XEM_REG_OFFSET + 0x1C) /* Rx packet length */
-#define XEM_TPLR_OFFSET (XEM_REG_OFFSET + 0x20) /* Tx packet length */
-#define XEM_TSR_OFFSET (XEM_REG_OFFSET + 0x24) /* Tx status */
-
-#define XEM_PFIFO_OFFSET 0x2000UL
-/* Tx registers */
-#define XEM_PFIFO_TXREG_OFFSET (XEM_PFIFO_OFFSET + 0x0)
-/* Rx registers */
-#define XEM_PFIFO_RXREG_OFFSET (XEM_PFIFO_OFFSET + 0x10)
-/* Tx keyhole */
-#define XEM_PFIFO_TXDATA_OFFSET (XEM_PFIFO_OFFSET + 0x100)
-/* Rx keyhole */
-#define XEM_PFIFO_RXDATA_OFFSET (XEM_PFIFO_OFFSET + 0x200)
-
-/*
- * EMAC Interrupt Registers (Status and Enable) masks. These registers are
- * part of the IPIF IP Interrupt registers
- */
-/* A mask for all transmit interrupts, used in polled mode */
-#define XEM_EIR_XMIT_ALL_MASK (XEM_EIR_XMIT_DONE_MASK |\
- XEM_EIR_XMIT_ERROR_MASK | \
- XEM_EIR_XMIT_SFIFO_EMPTY_MASK |\
- XEM_EIR_XMIT_LFIFO_FULL_MASK)
-
-/* Xmit complete */
-#define XEM_EIR_XMIT_DONE_MASK 0x00000001UL
-/* Recv complete */
-#define XEM_EIR_RECV_DONE_MASK 0x00000002UL
-/* Xmit error */
-#define XEM_EIR_XMIT_ERROR_MASK 0x00000004UL
-/* Recv error */
-#define XEM_EIR_RECV_ERROR_MASK 0x00000008UL
-/* Xmit status fifo empty */
-#define XEM_EIR_XMIT_SFIFO_EMPTY_MASK 0x00000010UL
-/* Recv length fifo empty */
-#define XEM_EIR_RECV_LFIFO_EMPTY_MASK 0x00000020UL
-/* Xmit length fifo full */
-#define XEM_EIR_XMIT_LFIFO_FULL_MASK 0x00000040UL
-/* Recv length fifo overrun */
-#define XEM_EIR_RECV_LFIFO_OVER_MASK 0x00000080UL
-/* Recv length fifo underrun */
-#define XEM_EIR_RECV_LFIFO_UNDER_MASK 0x00000100UL
-/* Xmit status fifo overrun */
-#define XEM_EIR_XMIT_SFIFO_OVER_MASK 0x00000200UL
-/* Transmit status fifo underrun */
-#define XEM_EIR_XMIT_SFIFO_UNDER_MASK 0x00000400UL
-/* Transmit length fifo overrun */
-#define XEM_EIR_XMIT_LFIFO_OVER_MASK 0x00000800UL
-/* Transmit length fifo underrun */
-#define XEM_EIR_XMIT_LFIFO_UNDER_MASK 0x00001000UL
-/* Transmit pause pkt received */
-#define XEM_EIR_XMIT_PAUSE_MASK 0x00002000UL
-
-/*
- * EMAC Control Register (ECR)
- */
-/* Full duplex mode */
-#define XEM_ECR_FULL_DUPLEX_MASK 0x80000000UL
-/* Reset transmitter */
-#define XEM_ECR_XMIT_RESET_MASK 0x40000000UL
-/* Enable transmitter */
-#define XEM_ECR_XMIT_ENABLE_MASK 0x20000000UL
-/* Reset receiver */
-#define XEM_ECR_RECV_RESET_MASK 0x10000000UL
-/* Enable receiver */
-#define XEM_ECR_RECV_ENABLE_MASK 0x08000000UL
-/* Enable PHY */
-#define XEM_ECR_PHY_ENABLE_MASK 0x04000000UL
-/* Enable xmit pad insert */
-#define XEM_ECR_XMIT_PAD_ENABLE_MASK 0x02000000UL
-/* Enable xmit FCS insert */
-#define XEM_ECR_XMIT_FCS_ENABLE_MASK 0x01000000UL
-/* Enable unicast addr */
-#define XEM_ECR_UNICAST_ENABLE_MASK 0x00020000UL
-/* Enable broadcast addr */
-#define XEM_ECR_BROAD_ENABLE_MASK 0x00008000UL
-
-/*
- * Transmit Status Register (TSR)
- */
-/* Transmit excess deferral */
-#define XEM_TSR_EXCESS_DEFERRAL_MASK 0x80000000UL
-/* Transmit late collision */
-#define XEM_TSR_LATE_COLLISION_MASK 0x01000000UL
-
-#define ENET_MAX_MTU PKTSIZE
-#define ENET_ADDR_LENGTH 6
-
-static unsigned int etherrxbuff[PKTSIZE_ALIGN/4]; /* Receive buffer */
-
-static u8 emacaddr[ENET_ADDR_LENGTH] = { 0x00, 0x0a, 0x35, 0x00, 0x22, 0x01 };
-
-static xemac emac;
-
-void eth_halt(void)
-{
- debug ("eth_halt\n");
-}
-
-int eth_init(bd_t * bis)
-{
- uchar enetaddr[6];
- u32 helpreg;
- debug ("EMAC Initialization Started\n\r");
-
- if (emac.isstarted) {
- puts("Emac is started\n");
- return 0;
- }
-
- memset (&emac, 0, sizeof (xemac));
-
- emac.baseaddress = XILINX_EMAC_BASEADDR;
-
- /* Setting up FIFOs */
- emac.recvfifo.regbaseaddress = emac.baseaddress +
- XEM_PFIFO_RXREG_OFFSET;
- emac.recvfifo.databaseaddress = emac.baseaddress +
- XEM_PFIFO_RXDATA_OFFSET;
- out_be32 (emac.recvfifo.regbaseaddress, XPF_RESET_FIFO_MASK);
-
- emac.sendfifo.regbaseaddress = emac.baseaddress +
- XEM_PFIFO_TXREG_OFFSET;
- emac.sendfifo.databaseaddress = emac.baseaddress +
- XEM_PFIFO_TXDATA_OFFSET;
- out_be32 (emac.sendfifo.regbaseaddress, XPF_RESET_FIFO_MASK);
-
- /* Reset the entire IPIF */
- out_be32 (emac.baseaddress + XIIF_V123B_RESETR_OFFSET,
- XIIF_V123B_RESET_MASK);
-
- /* Stopping EMAC for setting up MAC */
- helpreg = in_be32 (emac.baseaddress + XEM_ECR_OFFSET);
- helpreg &= ~(XEM_ECR_XMIT_ENABLE_MASK | XEM_ECR_RECV_ENABLE_MASK);
- out_be32 (emac.baseaddress + XEM_ECR_OFFSET, helpreg);
-
- if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
- memcpy(enetaddr, emacaddr, ENET_ADDR_LENGTH);
- eth_setenv_enetaddr("ethaddr", enetaddr);
- }
-
- /* Set the device station address high and low registers */
- helpreg = (enetaddr[0] << 8) | enetaddr[1];
- out_be32 (emac.baseaddress + XEM_SAH_OFFSET, helpreg);
- helpreg = (enetaddr[2] << 24) | (enetaddr[3] << 16) |
- (enetaddr[4] << 8) | enetaddr[5];
- out_be32 (emac.baseaddress + XEM_SAL_OFFSET, helpreg);
-
- helpreg = XEM_ECR_UNICAST_ENABLE_MASK | XEM_ECR_BROAD_ENABLE_MASK |
- XEM_ECR_FULL_DUPLEX_MASK | XEM_ECR_XMIT_FCS_ENABLE_MASK |
- XEM_ECR_XMIT_PAD_ENABLE_MASK | XEM_ECR_PHY_ENABLE_MASK;
- out_be32 (emac.baseaddress + XEM_ECR_OFFSET, helpreg);
-
- emac.isstarted = 1;
-
- /* Enable the transmitter, and receiver */
- helpreg = in_be32 (emac.baseaddress + XEM_ECR_OFFSET);
- helpreg &= ~(XEM_ECR_XMIT_RESET_MASK | XEM_ECR_RECV_RESET_MASK);
- helpreg |= (XEM_ECR_XMIT_ENABLE_MASK | XEM_ECR_RECV_ENABLE_MASK);
- out_be32 (emac.baseaddress + XEM_ECR_OFFSET, helpreg);
-
- printf("EMAC Initialization complete\n\r");
- return 0;
-}
-
-int eth_send(volatile void *ptr, int len)
-{
- u32 intrstatus;
- u32 xmitstatus;
- u32 fifocount;
- u32 wordcount;
- u32 extrabytecount;
- u32 *wordbuffer = (u32 *) ptr;
-
- if (len > ENET_MAX_MTU)
- len = ENET_MAX_MTU;
-
- /*
- * Check for overruns and underruns for the transmit status and length
- * FIFOs and make sure the send packet FIFO is not deadlocked.
- * Any of these conditions is bad enough that we do not want to
- * continue. The upper layer software should reset the device to resolve
- * the error.
- */
- intrstatus = in_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET);
- if (intrstatus & (XEM_EIR_XMIT_SFIFO_OVER_MASK |
- XEM_EIR_XMIT_LFIFO_OVER_MASK)) {
- debug ("Transmitting overrun error\n");
- return 0;
- } else if (intrstatus & (XEM_EIR_XMIT_SFIFO_UNDER_MASK |
- XEM_EIR_XMIT_LFIFO_UNDER_MASK)) {
- debug ("Transmitting underrun error\n");
- return 0;
- } else if (in_be32 (emac.sendfifo.regbaseaddress +
- XPF_COUNT_STATUS_REG_OFFSET) & XPF_DEADLOCK_MASK) {
- debug ("Transmitting fifo error\n");
- return 0;
- }
-
- /*
- * Before writing to the data FIFO, make sure the length FIFO is not
- * full. The data FIFO might not be full yet even though the length FIFO
- * is. This avoids an overrun condition on the length FIFO and keeps the
- * FIFOs in sync.
- *
- * Clear the latched LFIFO_FULL bit so next time around the most
- * current status is represented
- */
- if (intrstatus & XEM_EIR_XMIT_LFIFO_FULL_MASK) {
- out_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET,
- intrstatus & XEM_EIR_XMIT_LFIFO_FULL_MASK);
- debug ("Fifo is full\n");
- return 0;
- }
-
- /* get the count of how many words may be inserted into the FIFO */
- fifocount = in_be32 (emac.sendfifo.regbaseaddress +
- XPF_COUNT_STATUS_REG_OFFSET) & XPF_COUNT_MASK;
- wordcount = len >> 2;
- extrabytecount = len & 0x3;
-
- if (fifocount < wordcount) {
- debug ("Sending packet is larger then size of FIFO\n");
- return 0;
- }
-
- for (fifocount = 0; fifocount < wordcount; fifocount++) {
- out_be32 (emac.sendfifo.databaseaddress, wordbuffer[fifocount]);
- }
- if (extrabytecount > 0) {
- u32 lastword = 0;
- u8 *extrabytesbuffer = (u8 *) (wordbuffer + wordcount);
-
- if (extrabytecount == 1) {
- lastword = extrabytesbuffer[0] << 24;
- } else if (extrabytecount == 2) {
- lastword = extrabytesbuffer[0] << 24 |
- extrabytesbuffer[1] << 16;
- } else if (extrabytecount == 3) {
- lastword = extrabytesbuffer[0] << 24 |
- extrabytesbuffer[1] << 16 |
- extrabytesbuffer[2] << 8;
- }
- out_be32 (emac.sendfifo.databaseaddress, lastword);
- }
-
- /* Loop on the MAC's status to wait for any pause to complete */
- intrstatus = in_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET);
- while ((intrstatus & XEM_EIR_XMIT_PAUSE_MASK) != 0) {
- intrstatus = in_be32 ((emac.baseaddress) +
- XIIF_V123B_IISR_OFFSET);
- /* Clear the pause status from the transmit status register */
- out_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET,
- intrstatus & XEM_EIR_XMIT_PAUSE_MASK);
- }
-
- /*
- * Set the MAC's transmit packet length register to tell it to transmit
- */
- out_be32 (emac.baseaddress + XEM_TPLR_OFFSET, len);
-
- /*
- * Loop on the MAC's status to wait for the transmit to complete.
- * The transmit status is in the FIFO when the XMIT_DONE bit is set.
- */
- do {
- intrstatus = in_be32 ((emac.baseaddress) +
- XIIF_V123B_IISR_OFFSET);
- }
- while ((intrstatus & XEM_EIR_XMIT_DONE_MASK) == 0);
-
- xmitstatus = in_be32 (emac.baseaddress + XEM_TSR_OFFSET);
-
- if (intrstatus & (XEM_EIR_XMIT_SFIFO_OVER_MASK |
- XEM_EIR_XMIT_LFIFO_OVER_MASK)) {
- debug ("Transmitting overrun error\n");
- return 0;
- } else if (intrstatus & (XEM_EIR_XMIT_SFIFO_UNDER_MASK |
- XEM_EIR_XMIT_LFIFO_UNDER_MASK)) {
- debug ("Transmitting underrun error\n");
- return 0;
- }
-
- /* Clear the interrupt status register of transmit statuses */
- out_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET,
- intrstatus & XEM_EIR_XMIT_ALL_MASK);
-
- /*
- * Collision errors are stored in the transmit status register
- * instead of the interrupt status register
- */
- if ((xmitstatus & XEM_TSR_EXCESS_DEFERRAL_MASK) ||
- (xmitstatus & XEM_TSR_LATE_COLLISION_MASK)) {
- debug ("Transmitting collision error\n");
- return 0;
- }
- return 1;
-}
-
-int eth_rx(void)
-{
- u32 pktlength;
- u32 intrstatus;
- u32 fifocount;
- u32 wordcount;
- u32 extrabytecount;
- u32 lastword;
- u8 *extrabytesbuffer;
-
- if (in_be32 (emac.recvfifo.regbaseaddress + XPF_COUNT_STATUS_REG_OFFSET)
- & XPF_DEADLOCK_MASK) {
- out_be32 (emac.recvfifo.regbaseaddress, XPF_RESET_FIFO_MASK);
- debug ("Receiving FIFO deadlock\n");
- return 0;
- }
-
- /*
- * Get the interrupt status to know what happened (whether an error
- * occurred and/or whether frames have been received successfully).
- * When clearing the intr status register, clear only statuses that
- * pertain to receive.
- */
- intrstatus = in_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET);
- /*
- * Before reading from the length FIFO, make sure the length FIFO is not
- * empty. We could cause an underrun error if we try to read from an
- * empty FIFO.
- */
- if (!(intrstatus & XEM_EIR_RECV_DONE_MASK)) {
- /* debug ("Receiving FIFO is empty\n"); */
- return 0;
- }
-
- /*
- * Determine, from the MAC, the length of the next packet available
- * in the data FIFO (there should be a non-zero length here)
- */
- pktlength = in_be32 (emac.baseaddress + XEM_RPLR_OFFSET);
- if (!pktlength) {
- return 0;
- }
-
- /*
- * Write the RECV_DONE bit in the status register to clear it. This bit
- * indicates the RPLR is non-empty, and we know it's set at this point.
- * We clear it so that subsequent entry into this routine will reflect
- * the current status. This is done because the non-empty bit is latched
- * in the IPIF, which means it may indicate a non-empty condition even
- * though there is something in the FIFO.
- */
- out_be32 ((emac.baseaddress) + XIIF_V123B_IISR_OFFSET,
- XEM_EIR_RECV_DONE_MASK);
-
- fifocount = in_be32 (emac.recvfifo.regbaseaddress +
- XPF_COUNT_STATUS_REG_OFFSET) & XPF_COUNT_MASK;
-
- if ((fifocount * 4) < pktlength) {
- debug ("Receiving FIFO is smaller than packet size.\n");
- return 0;
- }
-
- wordcount = pktlength >> 2;
- extrabytecount = pktlength & 0x3;
-
- for (fifocount = 0; fifocount < wordcount; fifocount++) {
- etherrxbuff[fifocount] =
- in_be32 (emac.recvfifo.databaseaddress);
- }
-
- /*
- * if there are extra bytes to handle, read the last word from the FIFO
- * and insert the extra bytes into the buffer
- */
- if (extrabytecount > 0) {
- extrabytesbuffer = (u8 *) (etherrxbuff + wordcount);
-
- lastword = in_be32 (emac.recvfifo.databaseaddress);
-
- /*
- * one extra byte in the last word, put the byte into the next
- * location of the buffer, bytes in a word of the FIFO are
- * ordered from most significant byte to least
- */
- if (extrabytecount == 1) {
- extrabytesbuffer[0] = (u8) (lastword >> 24);
- } else if (extrabytecount == 2) {
- extrabytesbuffer[0] = (u8) (lastword >> 24);
- extrabytesbuffer[1] = (u8) (lastword >> 16);
- } else if (extrabytecount == 3) {
- extrabytesbuffer[0] = (u8) (lastword >> 24);
- extrabytesbuffer[1] = (u8) (lastword >> 16);
- extrabytesbuffer[2] = (u8) (lastword >> 8);
- }
- }
- NetReceive((uchar *)etherrxbuff, pktlength);
- return 1;
-}
diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h
index 64eb0e0..3fd2211 100644
--- a/include/configs/microblaze-generic.h
+++ b/include/configs/microblaze-generic.h
@@ -58,10 +58,7 @@
/*#define CONFIG_SYS_RESET_ADDRESS TEXT_BASE*/
/* ethernet */
-#ifdef XILINX_EMAC_BASEADDR
- #define CONFIG_XILINX_EMAC 1
- #define CONFIG_SYS_ENET
-#elif XILINX_EMACLITE_BASEADDR
+#ifdef XILINX_EMACLITE_BASEADDR
#define CONFIG_XILINX_EMACLITE 1
#define CONFIG_SYS_ENET
#elif XILINX_LLTEMAC_BASEADDR
--
1.5.4.7
More information about the U-Boot
mailing list