[U-Boot] [PATCH 2/3] delta: use new generic NAND controller driver

Marcel Ziswiler marcel at ziswiler.com
Thu Dec 24 04:36:30 CET 2009


This patch adapts the Monahan/PXA3xx board delta to use the new generic NAND
controller driver.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler at noser.com>
---
 board/delta/Makefile    |    2 +-
 board/delta/delta.c     |   50 +++++
 board/delta/nand.c      |  554 -----------------------------------------------
 include/configs/delta.h |   32 +--
 4 files changed, 59 insertions(+), 579 deletions(-)
 delete mode 100644 board/delta/nand.c

diff --git a/board/delta/Makefile b/board/delta/Makefile
index 648e00c..9b5545d 100644
--- a/board/delta/Makefile
+++ b/board/delta/Makefile
@@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= delta.o nand.o
+COBJS	:= delta.o
 SOBJS	:= lowlevel_init.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/board/delta/delta.c b/board/delta/delta.c
index a294213..680f846 100644
--- a/board/delta/delta.c
+++ b/board/delta/delta.c
@@ -28,9 +28,12 @@
 #include <malloc.h>
 #include <command.h>
 #include <asm/arch/pxa-regs.h>
+#include <nand.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+extern int pxa3xx_nand_probe(struct nand_chip *chip);
+
 /* ------------------------------------------------------------------------- */
 
 static void init_DA9030(void);
@@ -96,6 +99,53 @@ int board_late_init(void)
 }
 
 /*
+ * Board-specific NAND initialization.
+ */
+int board_nand_init(struct nand_chip *chip)
+{
+	/* no idea what is done here, see zylonite.c */
+	GPIO4 = 0x1;
+
+	/* Setting up DFC GPIOs. */
+
+	/* ND_IO<15:0> alternate function 1 */
+	DF_IO0 = 0x00000001;
+	DF_IO1 = 0x00000001;
+	DF_IO2 = 0x00000001;
+	DF_IO3 = 0x00000001;
+	DF_IO4 = 0x00000001;
+	DF_IO5 = 0x00000001;
+	DF_IO6 = 0x00000001;
+	DF_IO7 = 0x00000001;
+	DF_IO8 = 0x00000001;
+	DF_IO9 = 0x00000001;
+	DF_IO10 = 0x00000001;
+	DF_IO11 = 0x00000001;
+	DF_IO12 = 0x00000001;
+	DF_IO13 = 0x00000001;
+	DF_IO14 = 0x00000001;
+	DF_IO15 = 0x00000001;
+	/* ND_nCS0 and ND_nCS1 alternate function 1 */
+	DF_nCS0 = 0x00000001;
+	DF_nCS1 = 0x00000001;
+	/* ND_nWE and ND_nRE alternate function 1, data on pad sent during
+	   D1-D3 low power mode, slow 10 mA drive */
+	DF_nWE = 0x00001901;
+	DF_nRE = 0x00001901;
+	/* ND_CLE alternate function 0 */
+	DF_CLE_nOE = 0x00001900;
+	/* ND_ALE alternate function 1, data on pad sent during
+	   D1-D3 low power mode, slow 10 mA drive */
+	DF_ALE_nWE1 = 0x00001901;
+	DF_ALE_nWE2 = 0x00001901;
+	/* ND_RnB alternate function 0, data on pad sent during
+	   D1-D3 low power mode, slow 10 mA drive */
+	DF_INT_RnB = 0x00001900;
+
+	return pxa3xx_nand_probe(chip);
+}
+
+/*
  * Magic Key Handling, mainly copied from board/lwmon/lwmon.c
  */
 #ifdef DELTA_CHECK_KEYBD
diff --git a/board/delta/nand.c b/board/delta/nand.c
deleted file mode 100644
index 85a6ba2..0000000
--- a/board/delta/nand.c
+++ /dev/null
@@ -1,554 +0,0 @@
-/*
- * (C) Copyright 2006 DENX Software Engineering
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-#include <asm/arch/pxa-regs.h>
-
-#ifdef CONFIG_SYS_DFC_DEBUG1
-# define DFC_DEBUG1(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG1(fmt, args...)
-#endif
-
-#ifdef CONFIG_SYS_DFC_DEBUG2
-# define DFC_DEBUG2(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG2(fmt, args...)
-#endif
-
-#ifdef CONFIG_SYS_DFC_DEBUG3
-# define DFC_DEBUG3(fmt, args...) printf(fmt, ##args)
-#else
-# define DFC_DEBUG3(fmt, args...)
-#endif
-
-/* These really don't belong here, as they are specific to the NAND Model */
-static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
-
-static struct nand_bbt_descr delta_bbt_descr = {
-	.options = 0,
-	.offs = 0,
-	.len = 2,
-	.pattern = scan_ff_pattern
-};
-
-static struct nand_ecclayout delta_oob = {
-	.eccbytes = 6,
-	.eccpos = {2, 3, 4, 5, 6, 7},
-	.oobfree = { {8, 2}, {12, 4} }
-};
-
-/*
- * not required for Monahans DFC
- */
-static void dfc_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	return;
-}
-
-#if 0
-/* read device ready pin */
-static int dfc_device_ready(struct mtd_info *mtdinfo)
-{
-	if(NDSR & NDSR_RDY)
-		return 1;
-	else
-		return 0;
-	return 0;
-}
-#endif
-
-/*
- * Write buf to the DFC Controller Data Buffer
- */
-static void dfc_write_buf(struct mtd_info *mtd, const u_char *buf, int len)
-{
-	unsigned long bytes_multi = len & 0xfffffffc;
-	unsigned long rest = len & 0x3;
-	unsigned long *long_buf;
-	int i;
-
-	DFC_DEBUG2("dfc_write_buf: writing %d bytes starting with 0x%x.\n", len, *((unsigned long*) buf));
-	if(bytes_multi) {
-		for(i=0; i<bytes_multi; i+=4) {
-			long_buf = (unsigned long*) &buf[i];
-			NDDB = *long_buf;
-		}
-	}
-	if(rest) {
-		printf("dfc_write_buf: ERROR, writing non 4-byte aligned data.\n");
-	}
-	return;
-}
-
-
-static void dfc_read_buf(struct mtd_info *mtd, u_char* const buf, int len)
-{
-	int i=0, j;
-
-	/* we have to be carefull not to overflow the buffer if len is
-	 * not a multiple of 4 */
-	unsigned long bytes_multi = len & 0xfffffffc;
-	unsigned long rest = len & 0x3;
-	unsigned long *long_buf;
-
-	DFC_DEBUG3("dfc_read_buf: reading %d bytes.\n", len);
-	/* if there are any, first copy multiple of 4 bytes */
-	if(bytes_multi) {
-		for(i=0; i<bytes_multi; i+=4) {
-			long_buf = (unsigned long*) &buf[i];
-			*long_buf = NDDB;
-		}
-	}
-
-	/* ...then the rest */
-	if(rest) {
-		unsigned long rest_data = NDDB;
-		for(j=0;j<rest; j++)
-			buf[i+j] = (u_char) ((rest_data>>j) & 0xff);
-	}
-
-	return;
-}
-
-/*
- * read a word. Not implemented as not used in NAND code.
- */
-static u16 dfc_read_word(struct mtd_info *mtd)
-{
-	printf("dfc_read_word: UNIMPLEMENTED.\n");
-	return 0;
-}
-
-/* global var, too bad: mk at tbd: move to ->priv pointer */
-static unsigned long read_buf = 0;
-static int bytes_read = -1;
-
-/*
- * read a byte from NDDB Because we can only read 4 bytes from NDDB at
- * a time, we buffer the remaining bytes. The buffer is reset when a
- * new command is sent to the chip.
- *
- * WARNING:
- * This function is currently only used to read status and id
- * bytes. For these commands always 8 bytes need to be read from
- * NDDB. So we read and discard these bytes right now. In case this
- * function is used for anything else in the future, we must check
- * what was the last command issued and read the appropriate amount of
- * bytes respectively.
- */
-static u_char dfc_read_byte(struct mtd_info *mtd)
-{
-	unsigned char byte;
-	unsigned long dummy;
-
-	if(bytes_read < 0) {
-		read_buf = NDDB;
-		dummy = NDDB;
-		bytes_read = 0;
-	}
-	byte = (unsigned char) (read_buf>>(8 * bytes_read++));
-	if(bytes_read >= 4)
-		bytes_read = -1;
-
-	DFC_DEBUG2("dfc_read_byte: byte %u: 0x%x of (0x%x).\n", bytes_read - 1, byte, read_buf);
-	return byte;
-}
-
-/* calculate delta between OSCR values start and now  */
-static unsigned long get_delta(unsigned long start)
-{
-	unsigned long cur = OSCR;
-
-	if(cur < start) /* OSCR overflowed */
-		return (cur + (start^0xffffffff));
-	else
-		return (cur - start);
-}
-
-/* delay function, this doesn't belong here */
-static void wait_us(unsigned long us)
-{
-	unsigned long start = OSCR;
-	us = DIV_ROUND_UP(us * OSCR_CLK_FREQ, 1000);
-
-	while (get_delta(start) < us) {
-		/* do nothing */
-	}
-}
-
-static void dfc_clear_nddb(void)
-{
-	NDCR &= ~NDCR_ND_RUN;
-	wait_us(CONFIG_SYS_NAND_OTHER_TO);
-}
-
-/* wait_event with timeout */
-static unsigned long dfc_wait_event(unsigned long event)
-{
-	unsigned long ndsr, timeout, start = OSCR;
-
-	if(!event)
-		return 0xff000000;
-	else if(event & (NDSR_CS0_CMDD | NDSR_CS0_BBD))
-		timeout = DIV_ROUND_UP(CONFIG_SYS_NAND_PROG_ERASE_TO
-					* OSCR_CLK_FREQ, 1000);
-	else
-		timeout = DIV_ROUND_UP(CONFIG_SYS_NAND_OTHER_TO
-					* OSCR_CLK_FREQ, 1000);
-
-	while(1) {
-		ndsr = NDSR;
-		if(ndsr & event) {
-			NDSR |= event;
-			break;
-		}
-		if(get_delta(start) > timeout) {
-			DFC_DEBUG1("dfc_wait_event: TIMEOUT waiting for event: 0x%lx.\n", event);
-			return 0xff000000;
-		}
-
-	}
-	return ndsr;
-}
-
-/* we don't always wan't to do this */
-static void dfc_new_cmd(void)
-{
-	int retry = 0;
-	unsigned long status;
-
-	while(retry++ <= CONFIG_SYS_NAND_SENDCMD_RETRY) {
-		/* Clear NDSR */
-		NDSR = 0xFFF;
-
-		/* set NDCR[NDRUN] */
-		if(!(NDCR & NDCR_ND_RUN))
-			NDCR |= NDCR_ND_RUN;
-
-		status = dfc_wait_event(NDSR_WRCMDREQ);
-
-		if(status & NDSR_WRCMDREQ)
-			return;
-
-		DFC_DEBUG2("dfc_new_cmd: FAILED to get WRITECMDREQ, retry: %d.\n", retry);
-		dfc_clear_nddb();
-	}
-	DFC_DEBUG1("dfc_new_cmd: giving up after %d retries.\n", retry);
-}
-
-/* this function is called after Programm and Erase Operations to
- * check for success or failure */
-static int dfc_wait(struct mtd_info *mtd, struct nand_chip *this)
-{
-	unsigned long ndsr=0, event=0;
-	int state = this->state;
-
-	if(state == FL_WRITING) {
-		event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
-	} else if(state == FL_ERASING) {
-		event = NDSR_CS0_CMDD | NDSR_CS0_BBD;
-	}
-
-	ndsr = dfc_wait_event(event);
-
-	if((ndsr & NDSR_CS0_BBD) || (ndsr & 0xff000000))
-		return(0x1); /* Status Read error */
-	return 0;
-}
-
-/* cmdfunc send commands to the DFC */
-static void dfc_cmdfunc(struct mtd_info *mtd, unsigned command,
-			int column, int page_addr)
-{
-	/* register struct nand_chip *this = mtd->priv; */
-	unsigned long ndcb0=0, ndcb1=0, ndcb2=0, event=0;
-
-	/* clear the ugly byte read buffer */
-	bytes_read = -1;
-	read_buf = 0;
-
-	switch (command) {
-	case NAND_CMD_READ0:
-		DFC_DEBUG3("dfc_cmdfunc: NAND_CMD_READ0, page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		dfc_new_cmd();
-		ndcb0 = (NAND_CMD_READ0 | (4<<16));
-		column >>= 1; /* adjust for 16 bit bus */
-		ndcb1 = (((column>>1) & 0xff) |
-			 ((page_addr<<8) & 0xff00) |
-			 ((page_addr<<8) & 0xff0000) |
-			 ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_READ1:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READ1 unimplemented!\n");
-		goto end;
-	case NAND_CMD_READOOB:
-		DFC_DEBUG1("dfc_cmdfunc: NAND_CMD_READOOB unimplemented!\n");
-		goto end;
-	case NAND_CMD_READID:
-		dfc_new_cmd();
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_READID.\n");
-		ndcb0 = (NAND_CMD_READID | (3 << 21) | (1 << 16)); /* addr cycles*/
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_PAGEPROG:
-		/* sent as a multicommand in NAND_CMD_SEQIN */
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_PAGEPROG empty due to multicmd.\n");
-		goto end;
-	case NAND_CMD_ERASE1:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE1,  page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		dfc_new_cmd();
-		ndcb0 = (0xd060 | (1<<25) | (2<<21) | (1<<19) | (3<<16));
-		ndcb1 = (page_addr & 0x00ffffff);
-		goto write_cmd;
-	case NAND_CMD_ERASE2:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_ERASE2 empty due to multicmd.\n");
-		goto end;
-	case NAND_CMD_SEQIN:
-		/* send PAGE_PROG command(0x1080) */
-		dfc_new_cmd();
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_SEQIN/PAGE_PROG,  page_addr: 0x%x, column: 0x%x.\n", page_addr, (column>>1));
-		ndcb0 = (0x1080 | (1<<25) | (1<<21) | (1<<19) | (4<<16));
-		column >>= 1; /* adjust for 16 bit bus */
-		ndcb1 = (((column>>1) & 0xff) |
-			 ((page_addr<<8) & 0xff00) |
-			 ((page_addr<<8) & 0xff0000) |
-			 ((page_addr<<8) & 0xff000000)); /* make this 0x01000000 ? */
-		event = NDSR_WRDREQ;
-		goto write_cmd;
-	case NAND_CMD_STATUS:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_STATUS.\n");
-		dfc_new_cmd();
-		ndcb0 = NAND_CMD_STATUS | (4<<21);
-		event = NDSR_RDDREQ;
-		goto write_cmd;
-	case NAND_CMD_RESET:
-		DFC_DEBUG2("dfc_cmdfunc: NAND_CMD_RESET.\n");
-		ndcb0 = NAND_CMD_RESET | (5<<21);
-		event = NDSR_CS0_CMDD;
-		goto write_cmd;
-	default:
-		printk("dfc_cmdfunc: error, unsupported command.\n");
-		goto end;
-	}
-
- write_cmd:
-	NDCB0 = ndcb0;
-	NDCB0 = ndcb1;
-	NDCB0 = ndcb2;
-
-	/*  wait_event: */
-	dfc_wait_event(event);
- end:
-	return;
-}
-
-static void dfc_gpio_init(void)
-{
-	DFC_DEBUG2("Setting up DFC GPIO's.\n");
-
-	/* no idea what is done here, see zylonite.c */
-	GPIO4 = 0x1;
-
-	DF_ALE_WE1 = 0x00000001;
-	DF_ALE_WE2 = 0x00000001;
-	DF_nCS0 = 0x00000001;
-	DF_nCS1 = 0x00000001;
-	DF_nWE = 0x00000001;
-	DF_nRE = 0x00000001;
-	DF_IO0 = 0x00000001;
-	DF_IO8 = 0x00000001;
-	DF_IO1 = 0x00000001;
-	DF_IO9 = 0x00000001;
-	DF_IO2 = 0x00000001;
-	DF_IO10 = 0x00000001;
-	DF_IO3 = 0x00000001;
-	DF_IO11 = 0x00000001;
-	DF_IO4 = 0x00000001;
-	DF_IO12 = 0x00000001;
-	DF_IO5 = 0x00000001;
-	DF_IO13 = 0x00000001;
-	DF_IO6 = 0x00000001;
-	DF_IO14 = 0x00000001;
-	DF_IO7 = 0x00000001;
-	DF_IO15 = 0x00000001;
-
-	DF_nWE = 0x1901;
-	DF_nRE = 0x1901;
-	DF_CLE_NOE = 0x1900;
-	DF_ALE_WE1 = 0x1901;
-	DF_INT_RnB = 0x1900;
-}
-
-/*
- * Board-specific NAND initialization. The following members of the
- * argument are board-specific (per include/linux/mtd/nand_new.h):
- * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
- * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
- * - hwcontrol: hardwarespecific function for accesing control-lines
- * - dev_ready: hardwarespecific function for  accesing device ready/busy line
- * - enable_hwecc?: function to enable (reset)  hardware ecc generator. Must
- *   only be provided if a hardware ECC is available
- * - ecc.mode: mode of ecc, see defines
- * - chip_delay: chip dependent delay for transfering data from array to
- *   read regs (tR)
- * - options: various chip options. They can partly be set to inform
- *   nand_scan about special functionality. See the defines for further
- *   explanation
- * Members with a "?" were not set in the merged testing-NAND branch,
- * so they are not set here either.
- */
-int board_nand_init(struct nand_chip *nand)
-{
-	unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR;
-
-	/* set up GPIO Control Registers */
-	dfc_gpio_init();
-
-	/* turn on the NAND Controller Clock (104 MHz @ D0) */
-	CKENA |= (CKENA_4_NAND | CKENA_9_SMC);
-
-#undef CONFIG_SYS_TIMING_TIGHT
-#ifndef CONFIG_SYS_TIMING_TIGHT
-	tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tCH);
-	tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tCS);
-	tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tWH);
-	tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tWP);
-	tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tRH);
-	tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tRP);
-	tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) + 1),
-		 DFC_MAX_tR);
-	tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) + 1),
-		   DFC_MAX_tWHR);
-	tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) + 1),
-		  DFC_MAX_tAR);
-#else /* this is the tight timing */
-
-	tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US)),
-		  DFC_MAX_tCH);
-	tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US)),
-		  DFC_MAX_tCS);
-	tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US)),
-		  DFC_MAX_tWH);
-	tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US)),
-		  DFC_MAX_tWP);
-	tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US)),
-		  DFC_MAX_tRH);
-	tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US)),
-		  DFC_MAX_tRP);
-	tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) - tCH - 2),
-		 DFC_MAX_tR);
-	tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) - tCH - 2),
-		   DFC_MAX_tWHR);
-	tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) - 2),
-		  DFC_MAX_tAR);
-#endif /* CONFIG_SYS_TIMING_TIGHT */
-
-
-	DFC_DEBUG2("tCH=%u, tCS=%u, tWH=%u, tWP=%u, tRH=%u, tRP=%u, tR=%u, tWHR=%u, tAR=%u.\n", tCH, tCS, tWH, tWP, tRH, tRP, tR, tWHR, tAR);
-
-	/* tRP value is split in the register */
-	if(tRP & (1 << 4)) {
-		tRP_high = 1;
-		tRP &= ~(1 << 4);
-	} else {
-		tRP_high = 0;
-	}
-
-	NDTR0CS0 = (tCH << 19) |
-		(tCS << 16) |
-		(tWH << 11) |
-		(tWP << 8) |
-		(tRP_high << 6) |
-		(tRH << 3) |
-		(tRP << 0);
-
-	NDTR1CS0 = (tR << 16) |
-		(tWHR << 4) |
-		(tAR << 0);
-
-	/* If it doesn't work (unlikely) think about:
-	 *  - ecc enable
-	 *  - chip select don't care
-	 *  - read id byte count
-	 *
-	 * Intentionally enabled by not setting bits:
-	 *  - dma (DMA_EN)
-	 *  - page size = 512
-	 *  - cs don't care, see if we can enable later!
-	 *  - row address start position (after second cycle)
-	 *  - pages per block = 32
-	 *  - ND_RDY : clears command buffer
-	 */
-	/* NDCR_NCSX |		/\* Chip select busy don't care *\/ */
-
-	NDCR = (NDCR_SPARE_EN |		/* use the spare area */
-		NDCR_DWIDTH_C |		/* 16bit DFC data bus width  */
-		NDCR_DWIDTH_M |		/* 16 bit Flash device data bus width */
-		(2 << 16) |		/* read id count = 7 ???? mk at tbd */
-		NDCR_ND_ARB_EN |	/* enable bus arbiter */
-		NDCR_RDYM |		/* flash device ready ir masked */
-		NDCR_CS0_PAGEDM |	/* ND_nCSx page done ir masked */
-		NDCR_CS1_PAGEDM |
-		NDCR_CS0_CMDDM |	/* ND_CSx command done ir masked */
-		NDCR_CS1_CMDDM |
-		NDCR_CS0_BBDM |		/* ND_CSx bad block detect ir masked */
-		NDCR_CS1_BBDM |
-		NDCR_DBERRM |		/* double bit error ir masked */
-		NDCR_SBERRM |		/* single bit error ir masked */
-		NDCR_WRDREQM |		/* write data request ir masked */
-		NDCR_RDDREQM |		/* read data request ir masked */
-		NDCR_WRCMDREQM);	/* write command request ir masked */
-
-
-	/* wait 10 us due to cmd buffer clear reset */
-	/*	wait(10); */
-
-
-	nand->cmd_ctrl = dfc_hwcontrol;
-/*	nand->dev_ready = dfc_device_ready; */
-	nand->ecc.mode = NAND_ECC_SOFT;
-	nand->ecc.layout = &delta_oob;
-	nand->options = NAND_BUSWIDTH_16;
-	nand->waitfunc = dfc_wait;
-	nand->read_byte = dfc_read_byte;
-	nand->read_word = dfc_read_word;
-	nand->read_buf = dfc_read_buf;
-	nand->write_buf = dfc_write_buf;
-
-	nand->cmdfunc = dfc_cmdfunc;
-	nand->badblock_pattern = &delta_bbt_descr;
-	return 0;
-}
-
-#endif
diff --git a/include/configs/delta.h b/include/configs/delta.h
index 9c46c5b..cea41b5 100644
--- a/include/configs/delta.h
+++ b/include/configs/delta.h
@@ -178,7 +178,6 @@
 #define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO		16 /* valid values: 8, 16, 24, 31 */
 #define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO	1  /* valid values: 1, 2 */
 
-
 						/* valid baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
@@ -220,10 +219,13 @@
 /*
  * NAND Flash
  */
-#define CONFIG_SYS_NAND0_BASE		0x0 /* 0x43100040 */ /* 0x10000000 */
-#undef CONFIG_SYS_NAND1_BASE
+#define CONFIG_NAND_PXA3xx
+#define CONFIG_NAND_PXA3xx_CLK  104000000UL
+#define CONFIG_NEW_NAND_CODE
+#define CONFIG_SYS_NAND_HW_ECC
+
+#define CONFIG_SYS_NAND_BASE		0x0
 
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND0_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */
 
 /* nand timeout values */
@@ -232,32 +234,14 @@
 #define CONFIG_SYS_NAND_SENDCMD_RETRY	3
 #undef NAND_ALLOW_ERASE_ALL	/* Allow erasing bad blocks - don't use */
 
-/* NAND Timing Parameters (in ns) */
-#define NAND_TIMING_tCH		10
-#define NAND_TIMING_tCS		0
-#define NAND_TIMING_tWH		20
-#define NAND_TIMING_tWP		40
-
-#define NAND_TIMING_tRH		20
-#define NAND_TIMING_tRP		40
-
-#define NAND_TIMING_tR		11123
-#define NAND_TIMING_tWHR	100
-#define NAND_TIMING_tAR		10
-
-/* NAND debugging */
-#define CONFIG_SYS_DFC_DEBUG1 /* usefull */
-#undef CONFIG_SYS_DFC_DEBUG2  /* noisy */
-#undef CONFIG_SYS_DFC_DEBUG3  /* extremly noisy  */
-
 #define CONFIG_MTD_DEBUG
 #define CONFIG_MTD_DEBUG_VERBOSE 1
 
 #define CONFIG_SYS_NO_FLASH		1
 
-#define CONFIG_ENV_IS_IN_NAND	1
+#define CONFIG_ENV_IS_IN_NAND		1
 #define CONFIG_ENV_OFFSET		0x40000
 #define CONFIG_ENV_OFFSET_REDUND	0x44000
-#define CONFIG_ENV_SIZE		0x4000
+#define CONFIG_ENV_SIZE			0x4000
 
 #endif	/* __CONFIG_H */
-- 
1.6.0.4




More information about the U-Boot mailing list