[U-Boot] [PATCH 1/7] OMAP3: Overo: Clean up pin mux and GPIO configuration
Dirk Behme
dirk.behme at googlemail.com
Mon Feb 2 06:53:25 CET 2009
* Make Overo GPIO114 an input for touchscreen PENDOWN
* Make Overo GPIO144-147 readable
* Make Overo EHCI pinmux match beagle rev c setup
* Adjust pinmux for SMSC911X network chip support
* Remove unnecessary GPIO setup
* Fix merge error in Makefile
Signed-off-by: Steve Sakoman <sakoman at gmail.com>
Signed-off-by: Dirk Behme <dirk.behme at googlemail.com>
---
board/omap3/overo/Makefile | 1 +
board/omap3/overo/overo.c | 13 -------------
board/omap3/overo/overo.h | 18 ++++++++++--------
3 files changed, 11 insertions(+), 21 deletions(-)
Index: u-boot-main/board/omap3/overo/overo.h
===================================================================
--- u-boot-main.orig/board/omap3/overo/overo.h
+++ u-boot-main/board/omap3/overo/overo.h
@@ -130,7 +130,8 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
- MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | DIS | M4)) /*GPIO_64*/\
+ /* - SMSC911X_NRES*/\
MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_nCS3*/\
/*DSS*/\
MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
@@ -184,7 +185,7 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
- MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DX1), (IEN | PTD | EN | M4)) /*GPIO_114*/\
MUX_VAL(CP(CSI2_DY1), (IEN | PTU | EN | M4)) /*GPIO_115*/\
/*Audio Interface */\
MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
@@ -218,10 +219,10 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
- MUX_VAL(CP(UART2_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
- MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_145*/\
- MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M4)) /*GPIO_146*/\
- MUX_VAL(CP(UART2_RX), (IDIS | PTD | DIS | M4)) /*GPIO_147*/\
+ MUX_VAL(CP(UART2_CTS), (IEN | PTD | DIS | M4)) /*GPIO_144 - LCD_EN*/\
+ MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147*/\
MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
MUX_VAL(CP(UART1_RTS), (IEN | PTU | DIS | M4)) /*GPIO_149*/ \
MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M4)) /*GPIO_150-MMC3_WP*/\
@@ -271,7 +272,8 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) /*McSPI1_SOMI */\
MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
- MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ MUX_VAL(CP(MCSPI1_CS2), (IEN | PTD | DIS | M4)) /*GPIO_176*/\
+ /* - SMSC911X_IRQ*/\
MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA2*/\
MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA7*/\
MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA4*/\
@@ -306,7 +308,7 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT6*/\
MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | EN | M2)) /*MMC3_DAT5*/\
MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
- MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | EN | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DIR*/\
MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_NXT*/\
MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M3)) /*HSUSB2_DATA0*/\
Index: u-boot-main/board/omap3/overo/overo.c
===================================================================
--- u-boot-main.orig/board/omap3/overo/overo.c
+++ u-boot-main/board/omap3/overo/overo.c
@@ -58,21 +58,8 @@ int board_init(void)
*****************************************************************************/
int misc_init_r(void)
{
- gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
- gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
-
power_init_r();
- /* Configure GPIOs to output */
- writel(~((GPIO10) | GPIO9 | GPIO3 | GPIO2), &gpio6_base->oe);
- writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
-
- /* Set GPIOs */
- writel(GPIO10 | GPIO9 | GPIO3 | GPIO2, &gpio6_base->setdataout);
- writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
- GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
-
return 0;
}
Index: u-boot-main/board/omap3/overo/Makefile
===================================================================
--- u-boot-main.orig/board/omap3/overo/Makefile
+++ u-boot-main/board/omap3/overo/Makefile
@@ -46,3 +46,4 @@ include $(SRCTREE)/rules.mk
sinclude $(obj).depend
+#########################################################################
More information about the U-Boot
mailing list