[U-Boot] [PATCH v2 2/4] ppc_4xx: Apply new HW register names
Niklaus Giger
niklaus.giger at member.fsf.org
Sun Oct 4 20:04:20 CEST 2009
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger at member.fsf.org>
---
board/amcc/bamboo/bamboo.c | 32 +++++-----
board/amcc/canyonlands/canyonlands.c | 22 +++---
board/amcc/ebony/ebony.c | 22 +++---
board/amcc/katmai/katmai.c | 22 +++---
board/amcc/luan/epld.h | 22 +++---
board/amcc/luan/luan.c | 22 +++---
board/amcc/ocotea/ocotea.c | 22 +++---
board/amcc/sequoia/sequoia.c | 28 ++++----
board/amcc/taishan/showinfo.c | 112 ++++++++++++++++----------------
board/amcc/taishan/taishan.c | 22 +++---
board/amcc/yosemite/yosemite.c | 32 +++++-----
board/amcc/yucca/yucca.c | 22 +++---
board/esd/common/cmd_loadpci.c | 2 +-
board/esd/du440/du440.c | 28 ++++----
board/esd/pmc440/cmd_pmc440.c | 10 ++--
board/esd/pmc440/pmc440.c | 32 +++++-----
board/exbitgen/init.S | 4 +-
board/gdsys/gdppc440etx/gdppc440etx.c | 32 +++++-----
board/gdsys/intip/intip.c | 22 +++---
board/korat/korat.c | 28 ++++----
board/lwmon5/lwmon5.c | 32 +++++-----
board/netstal/hcu5/hcu5.c | 28 ++++----
board/pcs440ep/pcs440ep.c | 32 +++++-----
board/prodrive/alpr/alpr.c | 52 ++++++++--------
board/prodrive/p3p440/p3p440.c | 22 +++---
board/sandburst/common/ppc440gx_i2c.h | 2 +-
board/sandburst/common/sb_common.c | 22 +++---
board/xes/xpedite1000/xpedite1000.c | 24 ++++----
cpu/ppc4xx/4xx_pci.c | 48 +++++++-------
cpu/ppc4xx/cpu_init.c | 4 +-
cpu/ppc4xx/miiphy.c | 24 ++++----
cpu/ppc4xx/speed.c | 6 +-
drivers/net/4xx_enet.c | 100 +++++++++++++++---------------
post/cpu/ppc4xx/ether.c | 50 +++++++-------
34 files changed, 492 insertions(+), 492 deletions(-)
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 38186a5..2598f2c 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -542,22 +542,22 @@ void pci_target_init(struct pci_controller *hose)
| Use byte reversed out routines to handle endianess.
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*--------------------------------------------------------------------------+
* Set up Configuration registers
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index f359d23..d96d2fd 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -338,27 +338,27 @@ void pci_target_init(struct pci_controller * hose )
/*
* Disable everything
*/
- out_le32((void *)PCIX0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIX0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIX0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */
+ out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
+ out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
/*
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
*/
- out_le32((void *)PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIX0_PIM0LAH, 0);
- out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIX0_BAR0, 0);
+ out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out_le32((void *)PCIL0_PIM0LAH, 0);
+ out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out_le32((void *)PCIL0_BAR0, 0);
/*
* Program the board's subsystem id/vendor id
*/
- out_le16((void *)PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+ out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
- out_le16((void *)PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
+ out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index e61b5de..0ca1acc 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -210,28 +210,28 @@ void pci_target_init(struct pci_controller *hose)
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0SA, 0); /* disable */
- out32r(PCIX0_PIM1SA, 0); /* disable */
- out32r(PCIX0_PIM2SA, 0); /* disable */
- out32r(PCIX0_EROMBA, 0); /* disable expansion rom */
+ out32r(PCIL0_PIM0SA, 0); /* disable */
+ out32r(PCIL0_PIM1SA, 0); /* disable */
+ out32r(PCIL0_PIM2SA, 0); /* disable */
+ out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIX0_PIM0LAH, 0);
- out32r(PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out32r(PCIL0_PIM0LAH, 0);
+ out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out32r(PCIX0_BAR0, 0);
+ out32r(PCIL0_BAR0, 0);
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r(PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+ out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
- out16r(PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
+ out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index bcef707..6c54aa2 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -304,27 +304,27 @@ void pci_target_init(struct pci_controller * hose )
/*-------------------------------------------------------------------+
* Disable everything
*-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*-------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
*-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_BAR0, 0 );
/*-------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*-------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/luan/epld.h b/board/amcc/luan/epld.h
index 05362e0..569d78c 100644
--- a/board/amcc/luan/epld.h
+++ b/board/amcc/luan/epld.h
@@ -8,8 +8,8 @@
#define EPLD0_FLASH_SRAM_SEL_N 0x01 /* 0 SRAM at mem top, 1 small flash at mem top */
#define EPLD1_CLK_CNTL0 0x80 /* FSEL-FB1 of MPC9772 */
-#define EPLD1_PCIX0_CNTL1 0x40 /* S*0 of 9531 */
-#define EPLD1_PCIX0_CNTL2 0x20 /* S*1 of 9531 */
+#define EPLD1_PCIL0_CNTL1 0x40 /* S*0 of 9531 */
+#define EPLD1_PCIL0_CNTL2 0x20 /* S*1 of 9531 */
#define EPLD1_CLK_CNTL3 0x10 /* FSEL-B1 of MPC9772 */
#define EPLD1_CLK_CNTL4 0x08 /* FSEL-B0 of MPC9772 */
#define EPLD1_MASTER_CLOCK6 0x04 /* clock source select 6 */
@@ -29,25 +29,25 @@
#define EPLD3_STATUS_LED2 0x02 /* status LED 2 (1 = LED on) */
#define EPLD3_STATUS_LED1 0x01 /* status LED 1 (1 = LED on) */
-#define EPLD4_PCIX0_VTH1 0x80 /* PCI-X 0 VTH1 status */
-#define EPLD4_PCIX0_VTH2 0x40 /* PCI-X 0 VTH2 status */
-#define EPLD4_PCIX0_VTH3 0x20 /* PCI-X 0 VTH3 status */
-#define EPLD4_PCIX0_VTH4 0x10 /* PCI-X 0 VTH4 status */
+#define EPLD4_PCIL0_VTH1 0x80 /* PCI-X 0 VTH1 status */
+#define EPLD4_PCIL0_VTH2 0x40 /* PCI-X 0 VTH2 status */
+#define EPLD4_PCIL0_VTH3 0x20 /* PCI-X 0 VTH3 status */
+#define EPLD4_PCIL0_VTH4 0x10 /* PCI-X 0 VTH4 status */
#define EPLD4_PCIX1_VTH1 0x08 /* PCI-X 1 VTH1 status */
#define EPLD4_PCIX1_VTH2 0x04 /* PCI-X 1 VTH2 status */
#define EPLD4_PCIX1_VTH3 0x02 /* PCI-X 1 VTH3 status */
#define EPLD4_PCIX1_VTH4 0x01 /* PCI-X 1 VTH4 status */
-#define EPLD5_PCIX0_INT0 0x80 /* PCIX0 INT0 status, write 0 to reset */
-#define EPLD5_PCIX0_INT1 0x40 /* PCIX0 INT1 status, write 0 to reset */
-#define EPLD5_PCIX0_INT2 0x20 /* PCIX0 INT2 status, write 0 to reset */
-#define EPLD5_PCIX0_INT3 0x10 /* PCIX0 INT3 status, write 0 to reset */
+#define EPLD5_PCIL0_INT0 0x80 /* PCIX0 INT0 status, write 0 to reset */
+#define EPLD5_PCIL0_INT1 0x40 /* PCIX0 INT1 status, write 0 to reset */
+#define EPLD5_PCIL0_INT2 0x20 /* PCIX0 INT2 status, write 0 to reset */
+#define EPLD5_PCIL0_INT3 0x10 /* PCIX0 INT3 status, write 0 to reset */
#define EPLD5_PCIX1_INT0 0x08 /* PCIX1 INT0 status, write 0 to reset */
#define EPLD5_PCIX1_INT1 0x04 /* PCIX1 INT1 status, write 0 to reset */
#define EPLD5_PCIX1_INT2 0x02 /* PCIX1 INT2 status, write 0 to reset */
#define EPLD5_PCIX1_INT3 0x01 /* PCIX1 INT3 status, write 0 to reset */
-#define EPLD6_PCIX0_RESET_CTL 0x80 /* 0=enable slot reset, 1=disable slot reset */
+#define EPLD6_PCIL0_RESET_CTL 0x80 /* 0=enable slot reset, 1=disable slot reset */
#define EPLD6_PCIX1_RESET_CTL 0x40 /* 0=enable slot reset, 1=disable slot reset */
#define EPLD6_ETH_INT_MODE 0x20 /* 0=IRQ5 recv's external eth int */
#define EPLD6_PCIX2_RESET_CTL 0x10 /* 0=enable slot reset, 1=disable slot reset */
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 5f76672..a04f2af 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -173,28 +173,28 @@ void pci_target_init(struct pci_controller *hose)
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index d776eda..0aa317e 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -321,28 +321,28 @@ void pci_target_init(struct pci_controller * hose )
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 17f831c..d42c802 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -428,26 +428,26 @@ void pci_target_init(struct pci_controller *hose)
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*
* Set up Configuration registers
diff --git a/board/amcc/taishan/showinfo.c b/board/amcc/taishan/showinfo.c
index e4e441b..a9a80e5 100644
--- a/board/amcc/taishan/showinfo.c
+++ b/board/amcc/taishan/showinfo.c
@@ -39,13 +39,13 @@ void show_reset_reg(void)
mfcpr(CPR0_PLLD,reg);
printf("cpr_plld = %#010lx\n",reg);
- mfcpr(CPR0_PRIMAD,reg);
+ mfcpr(CPR0_PRIMAD0,reg);
printf("cpr_primad = %#010lx\n",reg);
- mfcpr(CPR0_PRIMBD,reg);
+ mfcpr(CPR0_PRIMBD0,reg);
printf("cpr_primbd = %#010lx\n",reg);
- mfcpr(CPR0_OPBD,reg);
+ mfcpr(CPR0_OPBD0,reg);
printf("cpr_opbd = %#010lx\n",reg);
mfcpr(CPR0_PERD,reg);
@@ -106,59 +106,59 @@ void show_xbridge_info(void)
printf("SDR0_XPLLD = %#010lx\n", reg);
printf("PCI-X Bridge Configure registers\n");
- printf("PCIX0_VENDID = %#06x\n", in16r(PCIX0_VENDID));
- printf("PCIX0_DEVID = %#06x\n", in16r(PCIX0_DEVID));
- printf("PCIX0_CMD = %#06x\n", in16r(PCIX0_CMD));
- printf("PCIX0_STATUS = %#06x\n", in16r(PCIX0_STATUS));
- printf("PCIX0_REVID = %#04x\n", in8(PCIX0_REVID));
- printf("PCIX0_CACHELS = %#04x\n", in8(PCIX0_CACHELS));
- printf("PCIX0_LATTIM = %#04x\n", in8(PCIX0_LATTIM));
- printf("PCIX0_HDTYPE = %#04x\n", in8(PCIX0_HDTYPE));
- printf("PCIX0_BIST = %#04x\n", in8(PCIX0_BIST));
-
- printf("PCIX0_BAR0 = %#010lx\n", in32r(PCIX0_BAR0));
- printf("PCIX0_BAR1 = %#010lx\n", in32r(PCIX0_BAR1));
- printf("PCIX0_BAR2 = %#010lx\n", in32r(PCIX0_BAR2));
- printf("PCIX0_BAR3 = %#010lx\n", in32r(PCIX0_BAR3));
- printf("PCIX0_BAR4 = %#010lx\n", in32r(PCIX0_BAR4));
- printf("PCIX0_BAR5 = %#010lx\n", in32r(PCIX0_BAR5));
-
- printf("PCIX0_CISPTR = %#010lx\n", in32r(PCIX0_CISPTR));
- printf("PCIX0_SBSSYSVID = %#010x\n", in16r(PCIX0_SBSYSVID));
- printf("PCIX0_SBSSYSID = %#010x\n", in16r(PCIX0_SBSYSID));
- printf("PCIX0_EROMBA = %#010lx\n", in32r(PCIX0_EROMBA));
- printf("PCIX0_CAP = %#04x\n", in8(PCIX0_CAP));
- printf("PCIX0_INTLN = %#04x\n", in8(PCIX0_INTLN));
- printf("PCIX0_INTPN = %#04x\n", in8(PCIX0_INTPN));
- printf("PCIX0_MINGNT = %#04x\n", in8(PCIX0_MINGNT));
- printf("PCIX0_MAXLTNCY = %#04x\n", in8(PCIX0_MAXLTNCY));
-
- printf("PCIX0_BRDGOPT1 = %#010lx\n", in32r(PCIX0_BRDGOPT1));
- printf("PCIX0_BRDGOPT2 = %#010lx\n", in32r(PCIX0_BRDGOPT2));
-
- printf("PCIX0_POM0LAL = %#010lx\n", in32r(PCIX0_POM0LAL));
- printf("PCIX0_POM0LAH = %#010lx\n", in32r(PCIX0_POM0LAH));
- printf("PCIX0_POM0SA = %#010lx\n", in32r(PCIX0_POM0SA));
- printf("PCIX0_POM0PCILAL = %#010lx\n", in32r(PCIX0_POM0PCIAL));
- printf("PCIX0_POM0PCILAH = %#010lx\n", in32r(PCIX0_POM0PCIAH));
- printf("PCIX0_POM1LAL = %#010lx\n", in32r(PCIX0_POM1LAL));
- printf("PCIX0_POM1LAH = %#010lx\n", in32r(PCIX0_POM1LAH));
- printf("PCIX0_POM1SA = %#010lx\n", in32r(PCIX0_POM1SA));
- printf("PCIX0_POM1PCILAL = %#010lx\n", in32r(PCIX0_POM1PCIAL));
- printf("PCIX0_POM1PCILAH = %#010lx\n", in32r(PCIX0_POM1PCIAH));
- printf("PCIX0_POM2SA = %#010lx\n", in32r(PCIX0_POM2SA));
-
- printf("PCIX0_PIM0SA = %#010lx\n", in32r(PCIX0_PIM0SA));
- printf("PCIX0_PIM0LAL = %#010lx\n", in32r(PCIX0_PIM0LAL));
- printf("PCIX0_PIM0LAH = %#010lx\n", in32r(PCIX0_PIM0LAH));
- printf("PCIX0_PIM1SA = %#010lx\n", in32r(PCIX0_PIM1SA));
- printf("PCIX0_PIM1LAL = %#010lx\n", in32r(PCIX0_PIM1LAL));
- printf("PCIX0_PIM1LAH = %#010lx\n", in32r(PCIX0_PIM1LAH));
- printf("PCIX0_PIM2SA = %#010lx\n", in32r(PCIX0_PIM1SA));
- printf("PCIX0_PIM2LAL = %#010lx\n", in32r(PCIX0_PIM1LAL));
- printf("PCIX0_PIM2LAH = %#010lx\n", in32r(PCIX0_PIM1LAH));
-
- printf("PCIX0_XSTS = %#010lx\n", in32r(PCIX0_STS));
+ printf("PCIL0_VENDID = %#06x\n", in16r(PCIL0_VENDID));
+ printf("PCIL0_DEVID = %#06x\n", in16r(PCIL0_DEVID));
+ printf("PCIL0_CMD = %#06x\n", in16r(PCIL0_CMD));
+ printf("PCIL0_STATUS = %#06x\n", in16r(PCIL0_STATUS));
+ printf("PCIL0_REVID = %#04x\n", in8(PCIL0_REVID));
+ printf("PCIL0_CACHELS = %#04x\n", in8(PCIL0_CACHELS));
+ printf("PCIL0_LATTIM = %#04x\n", in8(PCIL0_LATTIM));
+ printf("PCIL0_HDTYPE = %#04x\n", in8(PCIL0_HDTYPE));
+ printf("PCIL0_BIST = %#04x\n", in8(PCIL0_BIST));
+
+ printf("PCIL0_BAR0 = %#010lx\n", in32r(PCIL0_BAR0));
+ printf("PCIL0_BAR1 = %#010lx\n", in32r(PCIL0_BAR1));
+ printf("PCIL0_BAR2 = %#010lx\n", in32r(PCIL0_BAR2));
+ printf("PCIL0_BAR3 = %#010lx\n", in32r(PCIL0_BAR3));
+ printf("PCIL0_BAR4 = %#010lx\n", in32r(PCIL0_BAR4));
+ printf("PCIL0_BAR5 = %#010lx\n", in32r(PCIL0_BAR5));
+
+ printf("PCIL0_CISPTR = %#010lx\n", in32r(PCIL0_CISPTR));
+ printf("PCIL0_SBSSYSVID = %#010x\n", in16r(PCIL0_SBSYSVID));
+ printf("PCIL0_SBSSYSID = %#010x\n", in16r(PCIL0_SBSYSID));
+ printf("PCIL0_EROMBA = %#010lx\n", in32r(PCIL0_EROMBA));
+ printf("PCIL0_CAP = %#04x\n", in8(PCIL0_CAP));
+ printf("PCIL0_INTLN = %#04x\n", in8(PCIL0_INTLN));
+ printf("PCIL0_INTPN = %#04x\n", in8(PCIL0_INTPN));
+ printf("PCIL0_MINGNT = %#04x\n", in8(PCIL0_MINGNT));
+ printf("PCIL0_MAXLTNCY = %#04x\n", in8(PCIL0_MAXLTNCY));
+
+ printf("PCIL0_BRDGOPT1 = %#010lx\n", in32r(PCIL0_BRDGOPT1));
+ printf("PCIL0_BRDGOPT2 = %#010lx\n", in32r(PCIL0_BRDGOPT2));
+
+ printf("PCIL0_POM0LAL = %#010lx\n", in32r(PCIL0_POM0LAL));
+ printf("PCIL0_POM0LAH = %#010lx\n", in32r(PCIL0_POM0LAH));
+ printf("PCIL0_POM0SA = %#010lx\n", in32r(PCIL0_POM0SA));
+ printf("PCIL0_POM0PCILAL = %#010lx\n", in32r(PCIL0_POM0PCIAL));
+ printf("PCIL0_POM0PCILAH = %#010lx\n", in32r(PCIL0_POM0PCIAH));
+ printf("PCIL0_POM1LAL = %#010lx\n", in32r(PCIL0_POM1LAL));
+ printf("PCIL0_POM1LAH = %#010lx\n", in32r(PCIL0_POM1LAH));
+ printf("PCIL0_POM1SA = %#010lx\n", in32r(PCIL0_POM1SA));
+ printf("PCIL0_POM1PCILAL = %#010lx\n", in32r(PCIL0_POM1PCIAL));
+ printf("PCIL0_POM1PCILAH = %#010lx\n", in32r(PCIL0_POM1PCIAH));
+ printf("PCIL0_POM2SA = %#010lx\n", in32r(PCIL0_POM2SA));
+
+ printf("PCIL0_PIM0SA = %#010lx\n", in32r(PCIL0_PIM0SA));
+ printf("PCIL0_PIM0LAL = %#010lx\n", in32r(PCIL0_PIM0LAL));
+ printf("PCIL0_PIM0LAH = %#010lx\n", in32r(PCIL0_PIM0LAH));
+ printf("PCIL0_PIM1SA = %#010lx\n", in32r(PCIL0_PIM1SA));
+ printf("PCIL0_PIM1LAL = %#010lx\n", in32r(PCIL0_PIM1LAL));
+ printf("PCIL0_PIM1LAH = %#010lx\n", in32r(PCIL0_PIM1LAH));
+ printf("PCIL0_PIM2SA = %#010lx\n", in32r(PCIL0_PIM1SA));
+ printf("PCIL0_PIM2LAL = %#010lx\n", in32r(PCIL0_PIM1LAL));
+ printf("PCIL0_PIM2LAH = %#010lx\n", in32r(PCIL0_PIM1LAH));
+
+ printf("PCIL0_XSTS = %#010lx\n", in32r(PCIL0_STS));
}
int do_show_xbridge_info(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 4a0573e..0c20faf 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -254,28 +254,28 @@ void pci_target_init(struct pci_controller * hose )
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index 1ec13eb..7ceccfa 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -408,22 +408,22 @@ void pci_target_init(struct pci_controller *hose)
| Use byte reversed out routines to handle endianess.
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*--------------------------------------------------------------------------+
* Set up Configuration registers
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 033bdd2..150bbcc 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -632,27 +632,27 @@ void pci_target_init(struct pci_controller * hose )
/*-------------------------------------------------------------------+
* Disable everything
*-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*-------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
*-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_BAR0, 0 );
/*-------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*-------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/esd/common/cmd_loadpci.c b/board/esd/common/cmd_loadpci.c
index 47e946f..eecae0a 100644
--- a/board/esd/common/cmd_loadpci.c
+++ b/board/esd/common/cmd_loadpci.c
@@ -48,7 +48,7 @@ int do_loadpci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
u32 la, ptm1la;
#if defined(CONFIG_440)
- ptm1la = in32r(PCIX0_PTM1LA);
+ ptm1la = in32r(PCIL0_PTM1LA);
#else
ptm1la = in32r(PTM1LA);
#endif
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 056f455..d0e52cb 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -435,26 +435,26 @@ void pci_target_init(struct pci_controller *hose)
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*
* Set up Configuration registers
diff --git a/board/esd/pmc440/cmd_pmc440.c b/board/esd/pmc440/cmd_pmc440.c
index 1af431b..476e940 100644
--- a/board/esd/pmc440/cmd_pmc440.c
+++ b/board/esd/pmc440/cmd_pmc440.c
@@ -497,15 +497,15 @@ int do_pmm(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
/* map PCI address at 0xc0000000 in PLB space */
/* PMM1 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1MA, 0x00000000);
+ out32r(PCIL0_PMM1MA, 0x00000000);
/* PMM1 Local Address */
- out32r(PCIX0_PMM1LA, 0xc0000000);
+ out32r(PCIL0_PMM1LA, 0xc0000000);
/* PMM1 PCI Low Address */
- out32r(PCIX0_PMM1PCILA, pciaddr);
+ out32r(PCIL0_PMM1PCILA, pciaddr);
/* PMM1 PCI High Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000);
+ out32r(PCIL0_PMM1PCIHA, 0x00000000);
/* 256MB + No prefetching, and enable region */
- out32r(PCIX0_PMM1MA, 0xf0000001);
+ out32r(PCIL0_PMM1MA, 0xf0000001);
} else {
printf("Usage:\npmm %s\n", cmdtp->help);
}
diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c
index f0f9bff..ec92552 100644
--- a/board/esd/pmc440/pmc440.c
+++ b/board/esd/pmc440/pmc440.c
@@ -208,7 +208,7 @@ int misc_init_f(void)
if (getenv("pciearly") && (!is_monarch())) {
printf("PCI: early target init\n");
- pci_setup_indirect(&hose, PCIX0_CFGADR, PCIX0_CFGDATA);
+ pci_setup_indirect(&hose, PCIL0_CFGADR, PCIL0_CFGDATA);
pci_target_init(&hose);
}
return 0;
@@ -568,42 +568,42 @@ void pci_target_init(struct pci_controller *hose)
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xc0000001); /* 1G + No prefetching, */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xc0000001); /* 1G + No prefetching, */
/* and enable region */
if (!is_monarch()) {
ptmla_str = getenv("ptm1la");
ptmms_str = getenv("ptm1ms");
if(NULL != ptmla_str && NULL != ptmms_str ) {
- out32r(PCIX0_PTM1MS,
+ out32r(PCIL0_PTM1MS,
simple_strtoul(ptmms_str, NULL, 16));
- out32r(PCIX0_PTM1LA,
+ out32r(PCIL0_PTM1LA,
simple_strtoul(ptmla_str, NULL, 16));
} else {
/* BAR1: default top 64MB of RAM */
- out32r(PCIX0_PTM1MS, 0xfc000001);
- out32r(PCIX0_PTM1LA, 0x0c000000);
+ out32r(PCIL0_PTM1MS, 0xfc000001);
+ out32r(PCIL0_PTM1LA, 0x0c000000);
}
} else {
/* BAR1: default: complete 256MB RAM */
- out32r(PCIX0_PTM1MS, 0xf0000001);
- out32r(PCIX0_PTM1LA, 0x00000000);
+ out32r(PCIL0_PTM1MS, 0xf0000001);
+ out32r(PCIL0_PTM1LA, 0x00000000);
}
ptmla_str = getenv("ptm2la"); /* Local Addr. Reg */
ptmms_str = getenv("ptm2ms"); /* Memory Size/Attribute */
if(NULL != ptmla_str && NULL != ptmms_str ) {
- out32r(PCIX0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16));
- out32r(PCIX0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16));
+ out32r(PCIL0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16));
+ out32r(PCIL0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16));
} else {
/* BAR2: default: 4MB FPGA */
- out32r(PCIX0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0xef000000); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0xef000000); /* Local Addr. Reg */
}
if (is_monarch()) {
diff --git a/board/exbitgen/init.S b/board/exbitgen/init.S
index 7a9726f..721aaac 100644
--- a/board/exbitgen/init.S
+++ b/board/exbitgen/init.S
@@ -52,7 +52,7 @@
#define IIC_EXTSTS (I2C_REGISTERS_BASE_ADDRESS+IICEXTSTS)
#define IIC_LSADR (I2C_REGISTERS_BASE_ADDRESS+IICLSADR)
#define IIC_HSADR (I2C_REGISTERS_BASE_ADDRESS+IICHSADR)
-#define IIC_CLKDIV (I2C_REGISTERS_BASE_ADDRESS+IICCLKDIV)
+#define IIC_CLKDIV (I2C_REGISTERS_BASE_ADDRESS+IIC0_CLKDIV)
#define IIC_INTRMSK (I2C_REGISTERS_BASE_ADDRESS+IICINTRMSK)
#define IIC_XFRCNT (I2C_REGISTERS_BASE_ADDRESS+IICXFRCNT)
#define IIC_XTCNTLSS (I2C_REGISTERS_BASE_ADDRESS+IICXTCNTLSS)
@@ -537,7 +537,7 @@ read_spd:
WRITE_I2C(IICHSADR, 0x00) /* clear hi slave address */
WRITE_I2C(IICSTS, 0x08) /* update status register */
WRITE_I2C(IICEXTSTS, 0x8f)
- WRITE_I2C(IICCLKDIV, 0x05)
+ WRITE_I2C(IIC0_CLKDIV, 0x05)
WRITE_I2C(IICINTRMSK, 0x00) /* no interrupts */
WRITE_I2C(IICXFRCNT, 0x00) /* clear transfer count */
WRITE_I2C(IICXTCNTLSS, 0xf0) /* clear extended control & stat */
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c
index 7cc1bf2..90dbe52 100644
--- a/board/gdsys/gdppc440etx/gdppc440etx.c
+++ b/board/gdsys/gdppc440etx/gdppc440etx.c
@@ -239,22 +239,22 @@ void pci_target_init(struct pci_controller *hose)
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIX0_PMM0PCIHA, 0x00000000);
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIX0_PMM1PCIHA, 0x00000000);
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001);
- out32r(PCIX0_PTM1LA, 0);
- out32r(PCIX0_PTM2MS, 0);
- out32r(PCIX0_PTM2LA, 0);
+ out32r(PCIL0_PMM0MA, 0x00000000); /* disabled b4 setting */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
+ out32r(PCIL0_PMM0PCIHA, 0x00000000);
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
+
+ out32r(PCIL0_PMM1MA, 0x00000000); /* disabled b4 setting */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
+ out32r(PCIL0_PMM1PCIHA, 0x00000000);
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
+
+ out32r(PCIL0_PTM1MS, 0x00000001);
+ out32r(PCIL0_PTM1LA, 0);
+ out32r(PCIL0_PTM2MS, 0);
+ out32r(PCIL0_PTM2LA, 0);
/*
* Set up Configuration registers
diff --git a/board/gdsys/intip/intip.c b/board/gdsys/intip/intip.c
index 2cd2e6d..b42e908 100644
--- a/board/gdsys/intip/intip.c
+++ b/board/gdsys/intip/intip.c
@@ -154,27 +154,27 @@ void pci_target_init(struct pci_controller *hose)
/*
* Disable everything
*/
- out_le32((void *)PCIX0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIX0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIX0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */
+ out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
+ out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
/*
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
*/
- out_le32((void *)PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIX0_PIM0LAH, 0);
- out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIX0_BAR0, 0);
+ out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out_le32((void *)PCIL0_PIM0LAH, 0);
+ out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out_le32((void *)PCIL0_BAR0, 0);
/*
* Program the board's subsystem id/vendor id
*/
- out_le16((void *)PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+ out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
- out_le16((void *)PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
+ out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/korat/korat.c b/board/korat/korat.c
index 40a097c..8c674a2 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -679,29 +679,29 @@ void pci_target_init(struct pci_controller *hose)
* Use byte reversed out routines to handle endianess.
* Make this region non-prefetchable.
*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA,
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA,
CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
/* - disabled b4 setting */
- out32r(PCIX0_PMM1LA,
+ out32r(PCIL0_PMM1LA,
CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA,
+ out32r(PCIL0_PMM1PCILA,
CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
/* and enable region */
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*
* Set up Configuration registers
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index f4090f4..ef7f2e8 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -351,22 +351,22 @@ void pci_target_init(struct pci_controller *hose)
| Use byte reversed out routines to handle endianess.
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*--------------------------------------------------------------------------+
* Set up Configuration registers
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 4522612..946c3f3 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -398,27 +398,27 @@ void pci_target_init(struct pci_controller *hose)
* Make this region non-prefetchable.
*/
/* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0MA, 0x00000000);
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0MA, 0x00000000);
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
/* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
/* 512M + No prefetching, and enable region */
- out32r(PCIX0_PMM0MA, 0xE0000001);
+ out32r(PCIL0_PMM0MA, 0xE0000001);
/* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1MA, 0x00000000);
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1MA, 0x00000000);
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
/* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
/* 512M + No prefetching, and enable region */
- out32r(PCIX0_PMM1MA, 0xE0000001);
+ out32r(PCIL0_PMM1MA, 0xE0000001);
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*
* Set up Configuration registers
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index ac059a9..b70827e 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -626,22 +626,22 @@ void pci_target_init(struct pci_controller *hose)
| Use byte reversed out routines to handle endianess.
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
- out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
+ out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
+
+ out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
/*--------------------------------------------------------------------------+
* Set up Configuration registers
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index cdb91ac..51335c4 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -192,28 +192,28 @@ void pci_target_init(struct pci_controller * hose )
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
@@ -270,21 +270,21 @@ void pci_master_init(struct pci_controller *hose)
| Use byte reversed out routines to handle endianess.
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
- out32r( PCIX0_POM0SA, 0 ); /* disable */
- out32r( PCIX0_POM1SA, 0 ); /* disable */
- out32r( PCIX0_POM2SA, 0 ); /* disable */
-
- out32r(PCIX0_POM0LAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_POM0LAH, 0x00000003); /* PMM0 Local Address */
- out32r(PCIX0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIX0_POM0PCIAH, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_POM0SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
-
- out32r(PCIX0_POM1LAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_POM1LAH, 0x00000003); /* PMM0 Local Address */
- out32r(PCIX0_POM1PCIAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIX0_POM1PCIAH, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIX0_POM1SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
+ out32r( PCIL0_POM0SA, 0 ); /* disable */
+ out32r( PCIL0_POM1SA, 0 ); /* disable */
+ out32r( PCIL0_POM2SA, 0 ); /* disable */
+
+ out32r(PCIL0_POM0LAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIL0_POM0LAH, 0x00000003); /* PMM0 Local Address */
+ out32r(PCIL0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIL0_POM0PCIAH, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_POM0SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
+
+ out32r(PCIL0_POM1LAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIL0_POM1LAH, 0x00000003); /* PMM0 Local Address */
+ out32r(PCIL0_POM1PCIAL, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIL0_POM1PCIAH, 0x00000000); /* PMM0 PCI High Address */
+ out32r(PCIL0_POM1SA, ~(0x10000000 - 1) | 1); /* 256MB + enable region */
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index 20fd4dc..9a07852 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -209,28 +209,28 @@ void pci_target_init(struct pci_controller *hose)
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0SA, 0); /* disable */
- out32r(PCIX0_PIM1SA, 0); /* disable */
- out32r(PCIX0_PIM2SA, 0); /* disable */
- out32r(PCIX0_EROMBA, 0); /* disable expansion rom */
+ out32r(PCIL0_PIM0SA, 0); /* disable */
+ out32r(PCIL0_PIM1SA, 0); /* disable */
+ out32r(PCIL0_PIM2SA, 0); /* disable */
+ out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r(PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIX0_PIM0LAH, 0);
- out32r(PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out32r(PCIL0_PIM0LAH, 0);
+ out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out32r(PCIX0_BAR0, 0);
+ out32r(PCIL0_BAR0, 0);
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r(PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+ out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
- out16r(PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
+ out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/sandburst/common/ppc440gx_i2c.h b/board/sandburst/common/ppc440gx_i2c.h
index 328abd6..90f27ca 100644
--- a/board/sandburst/common/ppc440gx_i2c.h
+++ b/board/sandburst/common/ppc440gx_i2c.h
@@ -44,7 +44,7 @@
#define IIC_EXTSTS1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICEXTSTS)
#define IIC_LSADR1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICLSADR)
#define IIC_HSADR1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICHSADR)
-#define IIC_CLKDIV1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICCLKDIV)
+#define IIC_CLKDIV1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IIC0_CLKDIV)
#define IIC_INTRMSK1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICINTRMSK)
#define IIC_XFRCNT1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICXFRCNT)
#define IIC_XTCNTLSS1 (I2C_REGISTERS_BUS1_BASE_ADDRESS+IICXTCNTLSS)
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index e1c6146..a484874 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -346,28 +346,28 @@ void pci_target_init(struct pci_controller * hose )
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+ out32r( PCIL0_PIM0SA, 0 ); /* disable */
+ out32r( PCIL0_PIM1SA, 0 ); /* disable */
+ out32r( PCIL0_PIM2SA, 0 ); /* disable */
+ out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+ out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
+ out32r( PCIL0_PIM0LAH, 0 );
+ out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIX0_BAR0, 0 );
+ out32r( PCIL0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+ out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/xes/xpedite1000/xpedite1000.c b/board/xes/xpedite1000/xpedite1000.c
index 011fb94..04949bb 100644
--- a/board/xes/xpedite1000/xpedite1000.c
+++ b/board/xes/xpedite1000/xpedite1000.c
@@ -156,7 +156,7 @@ int pci_pre_init(struct pci_controller * hose)
return 0;
#if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV)
- /* Setup System Device Register PCIX0_XCR */
+ /* Setup System Device Register PCIL0_XCR */
mfsdr(SDR0_XCR, strap);
strap &= 0x0f000000;
mtsdr(SDR0_XCR, strap);
@@ -175,26 +175,26 @@ int pci_pre_init(struct pci_controller * hose)
void pci_target_init(struct pci_controller * hose)
{
/* Disable everything */
- out32r(PCIX0_PIM0SA, 0);
- out32r(PCIX0_PIM1SA, 0);
- out32r(PCIX0_PIM2SA, 0);
- out32r(PCIX0_EROMBA, 0); /* disable expansion rom */
+ out32r(PCIL0_PIM0SA, 0);
+ out32r(PCIL0_PIM1SA, 0);
+ out32r(PCIL0_PIM2SA, 0);
+ out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
/*
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*/
- out32r(PCIX0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIX0_PIM0LAH, 0);
- out32r(PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out32r(PCIL0_PIM0LAH, 0);
+ out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out32r(PCIX0_BAR0, 0);
+ out32r(PCIL0_BAR0, 0);
/* Program the board's subsystem id/vendor id */
- out16r(PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+ out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
- out16r(PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY);
+ out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c
index e97f32c..fa521f0 100644
--- a/cpu/ppc4xx/4xx_pci.c
+++ b/cpu/ppc4xx/4xx_pci.c
@@ -518,7 +518,7 @@ int pci_440_init (struct pci_controller *hose)
/* PCI I/O space */
pci_set_region(hose->regions + reg_num++,
0x00000000,
- PCIX0_IOBASE,
+ PCIL0_IOBASE,
0x10000,
PCI_REGION_IO);
@@ -545,7 +545,7 @@ int pci_440_init (struct pci_controller *hose)
hose->region_count = reg_num;
- pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA);
+ pci_setup_indirect(hose, PCIL0_CFGADR, PCIL0_CFGDATA);
/* Let board change/modify hose & do initial checks */
if (pci_pre_init (hose) == 0) {
@@ -562,18 +562,18 @@ int pci_440_init (struct pci_controller *hose)
#if defined(CONFIG_SYS_PCI_TARGET_INIT)
pci_target_init(hose); /* Let board setup pci target */
#else
- out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_ID );
- out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
+ out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
+ out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_ID );
+ out16r( PCIL0_CLS, 0x00060000 ); /* Bridge, host bridge */
#endif
#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
- out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
- out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
-#elif defined(PCIX0_BRDGOPT1)
- out32r( PCIX0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */
- out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 1 ); /* Enable host config */
+ out32r( PCIL0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
+ out32r( PCIL0_BRDGOPT2, in32(PCIL0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
+#elif defined(PCIL0_BRDGOPT1)
+ out32r( PCIL0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */
+ out32r( PCIL0_BRDGOPT2, in32(PCIL0_BRDGOPT2) | 1 ); /* Enable host config */
#endif
/*--------------------------------------------------------------------------+
@@ -583,23 +583,23 @@ int pci_440_init (struct pci_controller *hose)
#if defined(CONFIG_SYS_PCI_MASTER_INIT)
pci_master_init(hose); /* Let board setup pci master */
#else
- out32r( PCIX0_POM0SA, 0 ); /* disable */
- out32r( PCIX0_POM1SA, 0 ); /* disable */
- out32r( PCIX0_POM2SA, 0 ); /* disable */
+ out32r( PCIL0_POM0SA, 0 ); /* disable */
+ out32r( PCIL0_POM1SA, 0 ); /* disable */
+ out32r( PCIL0_POM2SA, 0 ); /* disable */
#if defined(CONFIG_440SPE)
- out32r( PCIX0_POM0LAL, 0x10000000 );
- out32r( PCIX0_POM0LAH, 0x0000000c );
+ out32r( PCIL0_POM0LAL, 0x10000000 );
+ out32r( PCIL0_POM0LAH, 0x0000000c );
#elif defined(CONFIG_460EX) || defined(CONFIG_460GT)
- out32r( PCIX0_POM0LAL, 0x20000000 );
- out32r( PCIX0_POM0LAH, 0x0000000c );
+ out32r( PCIL0_POM0LAL, 0x20000000 );
+ out32r( PCIL0_POM0LAH, 0x0000000c );
#else
- out32r( PCIX0_POM0LAL, 0x00000000 );
- out32r( PCIX0_POM0LAH, 0x00000003 );
+ out32r( PCIL0_POM0LAL, 0x00000000 );
+ out32r( PCIL0_POM0LAH, 0x00000003 );
#endif
- out32r( PCIX0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE );
- out32r( PCIX0_POM0PCIAH, 0x00000000 );
- out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
- out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 );
+ out32r( PCIL0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE );
+ out32r( PCIL0_POM0PCIAH, 0x00000000 );
+ out32r( PCIL0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
+ out32r( PCIL0_STS, in32r( PCIL0_STS ) & ~0x0000fff8 );
#endif
/*--------------------------------------------------------------------------+
@@ -614,7 +614,7 @@ int pci_440_init (struct pci_controller *hose)
#endif
#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \
!defined(CONFIG_440EPX) && !defined(CONFIG_440GRX)
- out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER);
+ out16r( PCIL0_CMD, in16r( PCIL0_CMD ) | PCI_COMMAND_MASTER);
#endif
hose->last_busno = pci_hose_scan(hose);
}
diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c
index bd06b9b..a00da40 100644
--- a/cpu/ppc4xx/cpu_init.c
+++ b/cpu/ppc4xx/cpu_init.c
@@ -58,13 +58,13 @@ void reconfigure_pll(u32 new_cpu_freq)
target_perdv0 = 4;
target_spcid0 = 4;
- mfcpr(CPR0_PRIMBD, reg);
+ mfcpr(CPR0_PRIMBD0, reg);
temp = (reg & PRBDV_MASK) >> 24;
prbdv0 = temp ? temp : 8;
if (prbdv0 != target_prbdv0) {
reg &= ~PRBDV_MASK;
reg |= ((target_prbdv0 == 8 ? 0 : target_prbdv0) << 24);
- mtcpr(CPR0_PRIMBD, reg);
+ mtcpr(CPR0_PRIMBD0, reg);
reset_needed = 1;
}
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index fa3bfc8..22ed5c2 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -195,7 +195,7 @@ unsigned int miiphy_getemac_offset(u8 addr)
unsigned long eoffset;
/* Need to find out which mdi port we're using */
- zmii = in_be32((void *)ZMII_FER);
+ zmii = in_be32((void *)ZMII0_FER);
if (zmii & (ZMII_FER_MDI << ZMII_FER_V (0)))
/* using port 0 */
@@ -217,12 +217,12 @@ unsigned int miiphy_getemac_offset(u8 addr)
/* None of the mdi ports are enabled! */
/* enable port 0 */
zmii |= ZMII_FER_MDI << ZMII_FER_V (0);
- out_be32((void *)ZMII_FER, zmii);
+ out_be32((void *)ZMII0_FER, zmii);
eoffset = 0;
/* need to soft reset port 0 */
- zmii = in_be32((void *)EMAC_M0);
- zmii |= EMAC_M0_SRST;
- out_be32((void *)EMAC_M0, zmii);
+ zmii = in_be32((void *)EMAC0_MR0);
+ zmii |= EMAC_MR0_SRST;
+ out_be32((void *)EMAC0_MR0, zmii);
}
return (eoffset);
@@ -243,19 +243,19 @@ unsigned int miiphy_getemac_offset(u8 addr)
switch (addr) {
#if defined(CONFIG_HAS_ETH1) && defined(CONFIG_GPCS_PHY1_ADDR)
case CONFIG_GPCS_PHY1_ADDR:
- if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x100)))
+ if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x100)))
eoffset = 0x100;
break;
#endif
#if defined(CONFIG_HAS_ETH2) && defined(CONFIG_GPCS_PHY2_ADDR)
case CONFIG_GPCS_PHY2_ADDR:
- if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x300)))
+ if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x300)))
eoffset = 0x300;
break;
#endif
#if defined(CONFIG_HAS_ETH3) && defined(CONFIG_GPCS_PHY3_ADDR)
case CONFIG_GPCS_PHY3_ADDR:
- if (addr == EMAC_M1_IPPA_GET(in_be32((void *)EMAC_M1 + 0x400)))
+ if (addr == EMAC_MR1_IPPA_GET(in_be32((void *)EMAC0_MR1 + 0x400)))
eoffset = 0x400;
break;
#endif
@@ -278,9 +278,9 @@ static int emac_miiphy_wait(u32 emac_reg)
/* wait for completion */
i = 0;
do {
- sta_reg = in_be32((void *)EMAC_STACR + emac_reg);
+ sta_reg = in_be32((void *)EMAC0_STACR + emac_reg);
if (i++ > 5) {
- debug("%s [%d]: Timeout! EMAC_STACR=0x%0x\n", __func__,
+ debug("%s [%d]: Timeout! EMAC0_STACR=0x%0x\n", __func__,
__LINE__, sta_reg);
return -1;
}
@@ -324,7 +324,7 @@ static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value)
if (cmd == EMAC_STACR_WRITE)
memcpy(&sta_reg, &value, 2); /* put in data */
- out_be32((void *)EMAC_STACR + emac_reg, sta_reg);
+ out_be32((void *)EMAC0_STACR + emac_reg, sta_reg);
debug("%s [%d]: sta_reg=%08x\n", __func__, __LINE__, sta_reg);
/* wait for completion */
@@ -349,7 +349,7 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, unsigned char reg,
if (emac_miiphy_command(addr, reg, EMAC_STACR_READ, 0) != 0)
return -1;
- sta_reg = in_be32((void *)EMAC_STACR + emac_reg);
+ sta_reg = in_be32((void *)EMAC0_STACR + emac_reg);
*value = sta_reg >> 16;
return 0;
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index 988ba97..906face 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -334,7 +334,7 @@ void get_sys_info (sys_info_t *sysInfo)
sysInfo->pllFbkDiv = temp ? temp : 32;
lfdiv = reg & PLLD_LFBDV_MASK;
- mfcpr(CPR0_OPBD, reg);
+ mfcpr(CPR0_OPBD0, reg);
temp = (reg & OPBDDV_MASK) >> 24;
sysInfo->pllOpbDiv = temp ? temp : 4;
@@ -342,7 +342,7 @@ void get_sys_info (sys_info_t *sysInfo)
temp = (reg & PERDV_MASK) >> 24;
sysInfo->pllExtBusDiv = temp ? temp : 8;
- mfcpr(CPR0_PRIMBD, reg);
+ mfcpr(CPR0_PRIMBD0, reg);
temp = (reg & PRBDV_MASK) >> 24;
prbdv0 = temp ? temp : 8;
@@ -1050,7 +1050,7 @@ void get_sys_info (sys_info_t * sysInfo)
/*
* Determine OPBDV0
*/
- mfcpr(CPR0_OPBD, tmp);
+ mfcpr(CPR0_OPBD0, tmp);
tmp = (tmp >> 24) & 0x03;
sysInfo->pllOpbDiv = (tmp == 0) ? 4 : tmp;
diff --git a/drivers/net/4xx_enet.c b/drivers/net/4xx_enet.c
index afd1084..312b25e 100644
--- a/drivers/net/4xx_enet.c
+++ b/drivers/net/4xx_enet.c
@@ -44,7 +44,7 @@
* RX descriptor address up to the next cache line boundary.
* 16-Jan-00 Added support for booting with IP of 0x0 MKW
* 15-Mar-00 Updated enetInit() to enable broadcast addresses in the
- * EMAC_RXM register. JWB
+ * EMAC0_RXM register. JWB
* 12-Mar-01 anne-sophie.harnois at nextream.fr
* - Variables are compatible with those already defined in
* include/net.h
@@ -58,7 +58,7 @@
* 08-May-01 stefan.roese at esd-electronics.com
* - MAL error handling added (eth_init called again)
* 13-Nov-01 stefan.roese at esd-electronics.com
- * - Set IST bit in EMAC_M1 reg upon 100MBit or full duplex
+ * - Set IST bit in EMAC0_MR1 reg upon 100MBit or full duplex
* 04-Jan-02 stefan.roese at esd-electronics.com
* - Wait for PHY auto negotiation to complete added
* 06-Feb-02 stefan.roese at esd-electronics.com
@@ -359,7 +359,7 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
EMAC_4XX_HW_PST hw_p = dev->priv;
u32 val = 10000;
- out_be32((void *)EMAC_IER + hw_p->hw_addr, 0x00000000); /* disable emac interrupts */
+ out_be32((void *)EMAC0_IER + hw_p->hw_addr, 0x00000000); /* disable emac interrupts */
/* 1st reset MAL channel */
/* Note: writing a 0 to a channel has no effect */
@@ -382,7 +382,7 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
emac_loopback_enable(hw_p);
/* EMAC RESET */
- out_be32((void *)EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
+ out_be32((void *)EMAC0_MR0 + hw_p->hw_addr, EMAC_MR0_SRST);
/* remove clocks for EMAC internal loopback */
emac_loopback_disable(hw_p);
@@ -485,7 +485,7 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
/* Ensure we setup mdio for this devnum and ONLY this devnum */
zmiifer |= (ZMII_FER_MDI) << ZMII_FER_V(devnum);
- out_be32((void *)ZMII_FER, zmiifer);
+ out_be32((void *)ZMII0_FER, zmiifer);
out_be32((void *)RGMII_FER, rmiifer);
return ((int)pfc1);
@@ -504,21 +504,21 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
switch (pfc1) {
case SDR0_PFC1_SELECT_CONFIG_2:
/* 1 x GMII port */
- out_be32((void *)ZMII_FER, 0x00);
+ out_be32((void *)ZMII0_FER, 0x00);
out_be32((void *)RGMII_FER, 0x00000037);
bis->bi_phymode[0] = BI_PHYMODE_GMII;
bis->bi_phymode[1] = BI_PHYMODE_NONE;
break;
case SDR0_PFC1_SELECT_CONFIG_4:
/* 2 x RGMII ports */
- out_be32((void *)ZMII_FER, 0x00);
+ out_be32((void *)ZMII0_FER, 0x00);
out_be32((void *)RGMII_FER, 0x00000055);
bis->bi_phymode[0] = BI_PHYMODE_RGMII;
bis->bi_phymode[1] = BI_PHYMODE_RGMII;
break;
case SDR0_PFC1_SELECT_CONFIG_6:
/* 2 x SMII ports */
- out_be32((void *)ZMII_FER,
+ out_be32((void *)ZMII0_FER,
((ZMII_FER_SMII) << ZMII_FER_V(0)) |
((ZMII_FER_SMII) << ZMII_FER_V(1)));
out_be32((void *)RGMII_FER, 0x00000000);
@@ -527,7 +527,7 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
break;
case SDR0_PFC1_SELECT_CONFIG_1_2:
/* only 1 x MII supported */
- out_be32((void *)ZMII_FER, (ZMII_FER_MII) << ZMII_FER_V(0));
+ out_be32((void *)ZMII0_FER, (ZMII_FER_MII) << ZMII_FER_V(0));
out_be32((void *)RGMII_FER, 0x00000000);
bis->bi_phymode[0] = BI_PHYMODE_MII;
bis->bi_phymode[1] = BI_PHYMODE_NONE;
@@ -537,9 +537,9 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
}
/* Ensure we setup mdio for this devnum and ONLY this devnum */
- zmiifer = in_be32((void *)ZMII_FER);
+ zmiifer = in_be32((void *)ZMII0_FER);
zmiifer |= (ZMII_FER_MDI) << ZMII_FER_V(devnum);
- out_be32((void *)ZMII_FER, zmiifer);
+ out_be32((void *)ZMII0_FER, zmiifer);
return ((int)0x0);
}
@@ -953,18 +953,18 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
/* NOTE: Therefore, disable all other EMACS, since we handle */
/* NOTE: only one emac at a time */
reg = 0;
- out_be32((void *)ZMII_FER, 0);
+ out_be32((void *)ZMII0_FER, 0);
udelay (100);
#if defined(CONFIG_440GP) || defined(CONFIG_440EP) || defined(CONFIG_440GR)
- out_be32((void *)ZMII_FER, (ZMII_FER_RMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
+ out_be32((void *)ZMII0_FER, (ZMII_FER_RMII | ZMII_FER_MDI) << ZMII_FER_V (devnum));
#elif defined(CONFIG_440GX) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis);
#endif
- out_be32((void *)ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum));
+ out_be32((void *)ZMII0_SSR, ZMII0_SSR_SP << ZMII0_SSR_V(devnum));
#endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
#if defined(CONFIG_405EX)
ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis);
@@ -976,13 +976,13 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
emac_loopback_enable(hw_p);
/* EMAC RESET */
- out_be32((void *)EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
+ out_be32((void *)EMAC0_MR0 + hw_p->hw_addr, EMAC_MR0_SRST);
/* remove clocks for EMAC internal loopback */
emac_loopback_disable(hw_p);
failsafe = 1000;
- while ((in_be32((void *)EMAC_M0 + hw_p->hw_addr) & (EMAC_M0_SRST)) && failsafe) {
+ while ((in_be32((void *)EMAC0_MR0 + hw_p->hw_addr) & (EMAC_MR0_SRST)) && failsafe) {
udelay (1000);
failsafe--;
}
@@ -1000,15 +1000,15 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
opbfreq = sysinfo.freqOPB / 1000000;
if (opbfreq <= 50);
else if (opbfreq <= 66)
- mode_reg |= EMAC_M1_OBCI_66;
+ mode_reg |= EMAC_MR1_OBCI_66;
else if (opbfreq <= 83)
- mode_reg |= EMAC_M1_OBCI_83;
+ mode_reg |= EMAC_MR1_OBCI_83;
else if (opbfreq <= 100)
- mode_reg |= EMAC_M1_OBCI_100;
+ mode_reg |= EMAC_MR1_OBCI_100;
else
- mode_reg |= EMAC_M1_OBCI_GT100;
+ mode_reg |= EMAC_MR1_OBCI_GT100;
- out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
+ out_be32((void *)EMAC0_MR1 + hw_p->hw_addr, mode_reg);
#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
#if defined(CONFIG_GPCS_PHY_ADDR) || defined(CONFIG_GPCS_PHY1_ADDR) || \
@@ -1041,9 +1041,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
#endif
}
- mode_reg = in_be32((void *)EMAC_M1 + hw_p->hw_addr);
- mode_reg |= EMAC_M1_MF_1000GPCS | EMAC_M1_IPPA_SET(reg);
- out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
+ mode_reg = in_be32((void *)EMAC0_MR1 + hw_p->hw_addr);
+ mode_reg |= EMAC_MR1_MF_1000GPCS | EMAC_MR1_IPPA_SET(reg);
+ out_be32((void *)EMAC0_MR1 + hw_p->hw_addr, mode_reg);
/* Configure GPCS interface to recommended setting for SGMII */
miiphy_reset(dev->name, reg);
@@ -1250,11 +1250,11 @@ get_speed:
#endif
/* Set ZMII/RGMII speed according to the phy link speed */
- reg = in_be32((void *)ZMII_SSR);
+ reg = in_be32((void *)ZMII0_SSR);
if ( (speed == 100) || (speed == 1000) )
- out_be32((void *)ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum)));
+ out_be32((void *)ZMII0_SSR, reg | (ZMII0_SSR_SP << ZMII0_SSR_V (devnum)));
else
- out_be32((void *)ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum))));
+ out_be32((void *)ZMII0_SSR, reg & (~(ZMII0_SSR_SP << ZMII0_SSR_V (devnum))));
if ((devnum == 2) || (devnum == 3)) {
if (speed == 1000)
@@ -1381,7 +1381,7 @@ get_speed:
reg = reg << 8;
reg |= dev->enetaddr[1];
- out_be32((void *)EMAC_IAH + hw_p->hw_addr, reg);
+ out_be32((void *)EMAC0_IAH + hw_p->hw_addr, reg);
reg = 0x00000000;
reg |= dev->enetaddr[2]; /* set low address */
@@ -1392,7 +1392,7 @@ get_speed:
reg = reg << 8;
reg |= dev->enetaddr[5];
- out_be32((void *)EMAC_IAL + hw_p->hw_addr, reg);
+ out_be32((void *)EMAC0_IAL + hw_p->hw_addr, reg);
switch (devnum) {
case 1:
@@ -1480,9 +1480,9 @@ get_speed:
mtdcr (MAL0_RXCASR, (MAL_TXRX_CASR >> hw_p->devnum));
/* set transmit enable & receive enable */
- out_be32((void *)EMAC_M0 + hw_p->hw_addr, EMAC_M0_TXE | EMAC_M0_RXE);
+ out_be32((void *)EMAC0_MR0 + hw_p->hw_addr, EMAC_MR0_TXE | EMAC_MR0_RXE);
- mode_reg = in_be32((void *)EMAC_M1 + hw_p->hw_addr);
+ mode_reg = in_be32((void *)EMAC0_MR1 + hw_p->hw_addr);
/* set rx-/tx-fifo size */
mode_reg = (mode_reg & ~EMAC_MR1_FIFO_MASK) | EMAC_MR1_FIFO_SIZE;
@@ -1497,47 +1497,47 @@ get_speed:
pfc1 |= SDR0_PFC1_EM_1000;
mtsdr (SDR0_PFC1, pfc1);
#endif
- mode_reg = mode_reg | EMAC_M1_MF_1000MBPS | EMAC_M1_IST;
+ mode_reg = mode_reg | EMAC_MR1_MF_1000MBPS | EMAC_MR1_IST;
} else if (speed == _100BASET)
- mode_reg = mode_reg | EMAC_M1_MF_100MBPS | EMAC_M1_IST;
+ mode_reg = mode_reg | EMAC_MR1_MF_100MBPS | EMAC_MR1_IST;
else
mode_reg = mode_reg & ~0x00C00000; /* 10 MBPS */
if (duplex == FULL)
- mode_reg = mode_reg | 0x80000000 | EMAC_M1_IST;
+ mode_reg = mode_reg | 0x80000000 | EMAC_MR1_IST;
- out_be32((void *)EMAC_M1 + hw_p->hw_addr, mode_reg);
+ out_be32((void *)EMAC0_MR1 + hw_p->hw_addr, mode_reg);
/* Enable broadcast and indvidual address */
/* TBS: enabling runts as some misbehaved nics will send runts */
- out_be32((void *)EMAC_RXM + hw_p->hw_addr, EMAC_RMR_BAE | EMAC_RMR_IAE);
+ out_be32((void *)EMAC0_RXM + hw_p->hw_addr, EMAC_RMR_BAE | EMAC_RMR_IAE);
/* we probably need to set the tx mode1 reg? maybe at tx time */
/* set transmit request threshold register */
- out_be32((void *)EMAC_TRTR + hw_p->hw_addr, 0x18000000); /* 256 byte threshold */
+ out_be32((void *)EMAC0_TRTR + hw_p->hw_addr, 0x18000000); /* 256 byte threshold */
/* set receive low/high water mark register */
#if defined(CONFIG_440)
/* 440s has a 64 byte burst length */
- out_be32((void *)EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x80009000);
+ out_be32((void *)EMAC0_RX_HI_LO_WMARK + hw_p->hw_addr, 0x80009000);
#else
/* 405s have a 16 byte burst length */
- out_be32((void *)EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x0f002000);
+ out_be32((void *)EMAC0_RX_HI_LO_WMARK + hw_p->hw_addr, 0x0f002000);
#endif /* defined(CONFIG_440) */
- out_be32((void *)EMAC_TXM1 + hw_p->hw_addr, 0xf8640000);
+ out_be32((void *)EMAC0_TMR1 + hw_p->hw_addr, 0xf8640000);
/* Set fifo limit entry in tx mode 0 */
- out_be32((void *)EMAC_TXM0 + hw_p->hw_addr, 0x00000003);
+ out_be32((void *)EMAC0_TMR0 + hw_p->hw_addr, 0x00000003);
/* Frame gap set */
- out_be32((void *)EMAC_I_FRAME_GAP_REG + hw_p->hw_addr, 0x00000008);
+ out_be32((void *)EMAC0_I_FRAME_GAP_REG + hw_p->hw_addr, 0x00000008);
/* Set EMAC IER */
hw_p->emac_ier = EMAC_ISR_PTLE | EMAC_ISR_BFCS | EMAC_ISR_ORE | EMAC_ISR_IRE;
if (speed == _100BASET)
hw_p->emac_ier = hw_p->emac_ier | EMAC_ISR_SYE;
- out_be32((void *)EMAC_ISR + hw_p->hw_addr, 0xffffffff); /* clear pending interrupts */
- out_be32((void *)EMAC_IER + hw_p->hw_addr, hw_p->emac_ier);
+ out_be32((void *)EMAC0_ISR + hw_p->hw_addr, 0xffffffff); /* clear pending interrupts */
+ out_be32((void *)EMAC0_IER + hw_p->hw_addr, hw_p->emac_ier);
if (hw_p->first_init == 0) {
/*
@@ -1596,8 +1596,8 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
sync();
- out_be32((void *)EMAC_TXM0 + hw_p->hw_addr,
- in_be32((void *)EMAC_TXM0 + hw_p->hw_addr) | EMAC_TXM0_GNP0);
+ out_be32((void *)EMAC0_TMR0 + hw_p->hw_addr,
+ in_be32((void *)EMAC0_TMR0 + hw_p->hw_addr) | EMAC_TMR0_GNP0);
#ifdef INFO_4XX_ENET
hw_p->stats.pkts_tx++;
#endif
@@ -1607,9 +1607,9 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
*-----------------------------------------------------------------------*/
time_start = get_timer (0);
while (1) {
- temp_txm0 = in_be32((void *)EMAC_TXM0 + hw_p->hw_addr);
+ temp_txm0 = in_be32((void *)EMAC0_TMR0 + hw_p->hw_addr);
/* loop until either TINT turns on or 3 seconds elapse */
- if ((temp_txm0 & EMAC_TXM0_GNP0) != 0) {
+ if ((temp_txm0 & EMAC_TMR0_GNP0) != 0) {
/* transmit is done, so now check for errors
* If there is an error, an interrupt should
* happen when we return
@@ -1678,7 +1678,7 @@ int enetInt (struct eth_device *dev)
/* look for EMAC errors */
if ((uic_emac & UIC_ETHx) || (uic_emac_b & UIC_ETHxB)) {
- emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr);
+ emac_isr = in_be32((void *)EMAC0_ISR + hw_p->hw_addr);
emac_err(dev, emac_isr);
/* clear EMAC error interrupt status bits */
@@ -1752,7 +1752,7 @@ static void emac_err (struct eth_device *dev, unsigned long isr)
EMAC_4XX_HW_PST hw_p = dev->priv;
printf ("EMAC%d error occured.... ISR = %lx\n", hw_p->devnum, isr);
- out_be32((void *)EMAC_ISR + hw_p->hw_addr, isr);
+ out_be32((void *)EMAC0_ISR + hw_p->hw_addr, isr);
}
/*-----------------------------------------------------------------------------+
diff --git a/post/cpu/ppc4xx/ether.c b/post/cpu/ppc4xx/ether.c
index c3665da..a58db04 100644
--- a/post/cpu/ppc4xx/ether.c
+++ b/post/cpu/ppc4xx/ether.c
@@ -115,11 +115,11 @@ static void ether_post_init (int devnum, int hw_addr)
sync ();
#endif
/* reset emac */
- out_be32 ((void*)(EMAC_M0 + hw_addr), EMAC_M0_SRST);
+ out_be32 ((void*)(EMAC0_MR0 + hw_addr), EMAC_MR0_SRST);
sync ();
for (i = 0;; i++) {
- if (!(in_be32 ((void*)(EMAC_M0 + hw_addr)) & EMAC_M0_SRST))
+ if (!(in_be32 ((void*)(EMAC0_MR0 + hw_addr)) & EMAC_MR0_SRST))
break;
if (i >= 1000) {
printf ("Timeout resetting EMAC\n");
@@ -134,15 +134,15 @@ static void ether_post_init (int devnum, int hw_addr)
mode_reg = 0x0;
if (sysinfo.freqOPB <= 50000000);
else if (sysinfo.freqOPB <= 66666667)
- mode_reg |= EMAC_M1_OBCI_66;
+ mode_reg |= EMAC_MR1_OBCI_66;
else if (sysinfo.freqOPB <= 83333333)
- mode_reg |= EMAC_M1_OBCI_83;
+ mode_reg |= EMAC_MR1_OBCI_83;
else if (sysinfo.freqOPB <= 100000000)
- mode_reg |= EMAC_M1_OBCI_100;
+ mode_reg |= EMAC_MR1_OBCI_100;
else
- mode_reg |= EMAC_M1_OBCI_GT100;
+ mode_reg |= EMAC_MR1_OBCI_GT100;
- out_be32 ((void*)(EMAC_M1 + hw_addr), mode_reg);
+ out_be32 ((void*)(EMAC0_MR1 + hw_addr), mode_reg);
#endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */
@@ -210,40 +210,40 @@ static void ether_post_init (int devnum, int hw_addr)
/* set internal loopback mode */
#ifdef CONFIG_SYS_POST_ETHER_EXT_LOOPBACK
- out_be32 ((void*)(EMAC_M1 + hw_addr), EMAC_M1_FDE | 0 |
- EMAC_M1_RFS_4K | EMAC_M1_TX_FIFO_2K |
- EMAC_M1_MF_100MBPS | EMAC_M1_IST |
- in_be32 ((void*)(EMAC_M1 + hw_addr)));
+ out_be32 ((void*)(EMAC0_MR1 + hw_addr), EMAC_MR1_FDE | 0 |
+ EMAC_MR1_RFS_4K | EMAC_MR1_TX_FIFO_2K |
+ EMAC_MR1_MF_100MBPS | EMAC_MR1_IST |
+ in_be32 ((void*)(EMAC0_MR1 + hw_addr)));
#else
- out_be32 ((void*)(EMAC_M1 + hw_addr), EMAC_M1_FDE | EMAC_M1_ILE |
- EMAC_M1_RFS_4K | EMAC_M1_TX_FIFO_2K |
- EMAC_M1_MF_100MBPS | EMAC_M1_IST |
- in_be32 ((void*)(EMAC_M1 + hw_addr)));
+ out_be32 ((void*)(EMAC0_MR1 + hw_addr), EMAC_MR1_FDE | EMAC_MR1_ILE |
+ EMAC_MR1_RFS_4K | EMAC_MR1_TX_FIFO_2K |
+ EMAC_MR1_MF_100MBPS | EMAC_MR1_IST |
+ in_be32 ((void*)(EMAC0_MR1 + hw_addr)));
#endif
/* set transmit enable & receive enable */
- out_be32 ((void*)(EMAC_M0 + hw_addr), EMAC_M0_TXE | EMAC_M0_RXE);
+ out_be32 ((void*)(EMAC0_MR0 + hw_addr), EMAC_MR0_TXE | EMAC_MR0_RXE);
/* enable broadcast address */
- out_be32 ((void*)(EMAC_RXM + hw_addr), EMAC_RMR_BAE);
+ out_be32 ((void*)(EMAC0_RXM + hw_addr), EMAC_RMR_BAE);
/* set transmit request threshold register */
- out_be32 ((void*)(EMAC_TRTR + hw_addr), 0x18000000); /* 256 byte threshold */
+ out_be32 ((void*)(EMAC0_TRTR + hw_addr), 0x18000000); /* 256 byte threshold */
/* set receive low/high water mark register */
#if defined(CONFIG_440)
/* 440s has a 64 byte burst length */
- out_be32 ((void*)(EMAC_RX_HI_LO_WMARK + hw_addr), 0x80009000);
+ out_be32 ((void*)(EMAC0_RX_HI_LO_WMARK + hw_addr), 0x80009000);
#else
/* 405s have a 16 byte burst length */
- out_be32 ((void*)(EMAC_RX_HI_LO_WMARK + hw_addr), 0x0f002000);
+ out_be32 ((void*)(EMAC0_RX_HI_LO_WMARK + hw_addr), 0x0f002000);
#endif /* defined(CONFIG_440) */
- out_be32 ((void*)(EMAC_TXM1 + hw_addr), 0xf8640000);
+ out_be32 ((void*)(EMAC0_TMR1 + hw_addr), 0xf8640000);
/* Set fifo limit entry in tx mode 0 */
- out_be32 ((void*)(EMAC_TXM0 + hw_addr), 0x00000003);
+ out_be32 ((void*)(EMAC0_TMR0 + hw_addr), 0x00000003);
/* Frame gap set */
- out_be32 ((void*)(EMAC_I_FRAME_GAP_REG + hw_addr), 0x00000008);
+ out_be32 ((void*)(EMAC0_I_FRAME_GAP_REG + hw_addr), 0x00000008);
sync ();
}
@@ -270,7 +270,7 @@ static void ether_post_halt (int devnum, int hw_addr)
udelay (1000);
}
/* emac reset */
- out_be32 ((void*)(EMAC_M0 + hw_addr), EMAC_M0_SRST);
+ out_be32 ((void*)(EMAC0_MR0 + hw_addr), EMAC_MR0_SRST);
#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
/* remove clocks for EMAC internal loopback */
@@ -300,7 +300,7 @@ static void ether_post_send (int devnum, int hw_addr, void *packet, int length)
flush_dcache_range((u32)tx.data_ptr, (u32)tx.data_ptr + length);
sync ();
- out_be32 ((void*)(EMAC_TXM0 + hw_addr), in_be32 ((void*)(EMAC_TXM0 + hw_addr)) | EMAC_TXM0_GNP0);
+ out_be32 ((void*)(EMAC0_TMR0 + hw_addr), in_be32 ((void*)(EMAC0_TMR0 + hw_addr)) | EMAC_TMR0_GNP0);
sync ();
}
--
1.6.3.3
More information about the U-Boot
mailing list