[U-Boot] [PATCH v5] at91: Update MEESC board support

Tom Tom.Rix at windriver.com
Mon Oct 5 01:19:38 CEST 2009


I have pushed this to arm/next.
Tom

Daniel Gorsulowski wrote:
> This patch implements several updates:
> -disable CONFIG_ENV_OVERWRITE
> -add new hardware style variants and set the arch numbers appropriate
> -pass the serial# and hardware revision to the kernel
> -removed unused macros from include/configs/meesc.h
> -fixed multiline comment style
> 
> Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski at esd.eu>
> ---
> v2: - don't write the ethernet address to the EMAC module anymore
> 
> v3: - removed function meesc_set_arch_number and moved code to checkboard()
>     - reworked function get_board_serial()
>     - removed unused macros from include/configs/meesc.h
> 
> v4: - fixed commit message (to many characters)
>     - fixed indentation in switch-case statement
>     - fixed multiline comment style
> 
> v5: - changed error message on invalid hw_type ("FATAL" to "ERROR")
> 
>  board/esd/meesc/meesc.c |   65 +++++++++++++++++++++++++++++++++++++++++-----
>  include/configs/meesc.h |   25 ++++++------------
>  2 files changed, 66 insertions(+), 24 deletions(-)
> 
> diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
> index 636d0ed..efba60d 100644
> --- a/board/esd/meesc/meesc.c
> +++ b/board/esd/meesc/meesc.c
> @@ -126,8 +126,10 @@ static void meesc_ethercat_hw_init(void)
>  		AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9));
>  	at91_sys_write(AT91_SMC1_CYCLE(0),
>  		AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5));
> -	/* Configure behavior at external wait signal, byte-select mode, 16 bit
> -	data bus width, none data float wait states and TDF optimization */
> +	/*
> +	 * Configure behavior at external wait signal, byte-select mode, 16 bit
> +	 * data bus width, none data float wait states and TDF optimization
> +	 */
>  	at91_sys_write(AT91_SMC1_MODE(0),
>  		AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY |
>  		AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) |
> @@ -156,8 +158,32 @@ int board_eth_init(bd_t *bis)
>  int checkboard(void)
>  {
>  	char str[32];
> -
> -	puts("Board: esd CAN-EtherCAT Gateway");
> +	u_char hw_type;	/* hardware type */
> +
> +	/* read the "Type" register of the ET1100 controller */
> +	hw_type = readb(CONFIG_ET1100_BASE);
> +
> +	switch (hw_type) {
> +	case 0x11:
> +	case 0x3F:
> +		/* ET1100 present, arch number of MEESC-Board */
> +		gd->bd->bi_arch_number = MACH_TYPE_MEESC;
> +		puts("Board: CAN-EtherCAT Gateway");
> +		break;
> +	case 0xFF:
> +		/* no ET1100 present, arch number of EtherCAN/2-Board */
> +		gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
> +		puts("Board: EtherCAN/2 Gateway");
> +		/* switch on LED1D */
> +		at91_set_gpio_output(AT91_PIN_PB12, 1);
> +		break;
> +	default:
> +		/* assume, no ET1100 present, arch number of EtherCAN/2-Board */
> +		gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
> +		printf("ERROR! Read invalid hw_type: %02X\n", hw_type);
> +		puts("Board: EtherCAN/2 Gateway");
> +		break;
> +	}
>  	if (getenv_r("serial#", str, sizeof(str)) > 0) {
>  		puts(", serial# ");
>  		puts(str);
> @@ -167,6 +193,32 @@ int checkboard(void)
>  	return 0;
>  }
>  
> +#ifdef CONFIG_SERIAL_TAG
> +void get_board_serial(struct tag_serialnr *serialnr)
> +{
> +	char *str;
> +
> +	char *serial = getenv("serial#");
> +	if (serial) {
> +		str = strchr(serial, '_');
> +		if (str && (strlen(str) >= 4)) {
> +			serialnr->high = (*(str + 1) << 8) | *(str + 2);
> +			serialnr->low = simple_strtoul(str + 3, NULL, 16);
> +		}
> +	} else {
> +		serialnr->high = 0;
> +		serialnr->low = 0;
> +	}
> +}
> +#endif
> +
> +#ifdef CONFIG_REVISION_TAG
> +u32 get_board_rev(void)
> +{
> +	return hw_rev | 0x100;
> +}
> +#endif
> +
>  int board_init(void)
>  {
>  	/* Peripheral Clock Enable Register */
> @@ -174,8 +226,8 @@ int board_init(void)
>  					1 << AT91SAM9263_ID_PIOB |
>  					1 << AT91SAM9263_ID_PIOCDE);
>  
> -	/* arch number of MEESC-Board */
> -	gd->bd->bi_arch_number = MACH_TYPE_MEESC;
> +	/* initialize ET1100 Controller */
> +	meesc_ethercat_hw_init();
>  
>  	/* adress of boot parameters */
>  	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> @@ -184,7 +236,6 @@ int board_init(void)
>  #ifdef CONFIG_CMD_NAND
>  	meesc_nand_hw_init();
>  #endif
> -	meesc_ethercat_hw_init();
>  #ifdef CONFIG_HAS_DATAFLASH
>  	at91_spi0_hw_init(1 << 0);
>  #endif
> diff --git a/include/configs/meesc.h b/include/configs/meesc.h
> index 8253172..b996854 100644
> --- a/include/configs/meesc.h
> +++ b/include/configs/meesc.h
> @@ -36,13 +36,14 @@
>  #define CONFIG_MEESC			1	/* Board is esd MEESC */
>  #define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
>  #define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
> -#define CONFIG_ENV_OVERWRITE		1	/* necessary on prototypes */
>  #define CONFIG_DISPLAY_BOARDINFO	1
>  #define CONFIG_DISPLAY_CPUINFO		1	/* display cpu info and speed */
>  #define CONFIG_PREBOOT				/* enable preboot variable */
>  #define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
>  #define CONFIG_SETUP_MEMORY_TAGS	1
>  #define CONFIG_INITRD_TAG		1
> +#define CONFIG_SERIAL_TAG		1
> +#define CONFIG_REVISION_TAG		1
>  #undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
>  
>  #define CONFIG_SKIP_LOWLEVEL_INIT
> @@ -138,12 +139,13 @@
>  #define CONFIG_SYS_USE_DATAFLASH		1
>  #undef CONFIG_SYS_USE_NANDFLASH
>  
> -#ifdef CONFIG_SYS_USE_DATAFLASH
> -
>  /* CAN */
>  #define CONFIG_AT91_CAN				1
>  
> -/* bootstrap + u-boot + env + linux in dataflash on CS0 */
> +/* hw-controller addresses */
> +#define CONFIG_ET1100_BASE			0x70000000
> +
> +/* bootstrap + u-boot + env in dataflash on CS0 */
>  #define CONFIG_ENV_IS_IN_DATAFLASH	1
>  #define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
>  					0x8400)
> @@ -151,18 +153,6 @@
>  #define CONFIG_ENV_ADDR			(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
>  					CONFIG_ENV_OFFSET)
>  #define CONFIG_ENV_SIZE			0x4200
> -#define CONFIG_BOOTCOMMAND		"cp.b C0042000 22000000 210000; bootm"
> -
> -#else /* CONFIG_SYS_USE_NANDFLASH */
> -
> -/* bootstrap + u-boot + env + linux in nandflash */
> -#define CONFIG_ENV_IS_IN_NAND	1
> -#define CONFIG_ENV_OFFSET		0x60000
> -#define CONFIG_ENV_OFFSET_REDUND	0x80000
> -#define CONFIG_ENV_SIZE			0x20000		/* 1 sector = 128 kB */
> -#define CONFIG_BOOTCOMMAND		"nand read 22000000 A0000 200000; bootm"
> -
> -#endif
>  
>  #define CONFIG_BAUDRATE			115200
>  #define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
> @@ -178,7 +168,8 @@
>  /*
>   * Size of malloc() pool
>   */
> -#define CONFIG_SYS_MALLOC_LEN		0x2D000
> +#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + \
> +					128*1024, 0x1000)
>  #define CONFIG_SYS_GBL_DATA_SIZE	128	/* 128 bytes for initial data */
>  
>  #define CONFIG_STACKSIZE		(32 * 1024)	/* regular stack */



More information about the U-Boot mailing list