[U-Boot] [PATCH 5/5 v2] ARM:OMAP3:SDP3430: initial support
Nishanth Menon
nm at ti.com
Wed Oct 7 04:17:59 CEST 2009
From: David Brownell <david-b at pacbell.net>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc..
Completely configurable boot sequence and device mapping
etc..
For more details, please refer:
http://focus.ti.com/general/docs/wtbu/wtbugencontent.tsp?templateId=6123&navigationId=12013&contentId=28741
U-boot support introduced for:
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
TODO:
- mmc1
- NAND (boot or 128M storage)
- OneNAND (boot or 256M storage)
- Fix NOR env variable load
- Review SDRC timing configuration/DPLL
configuration
- Dynamically read FPGA dip switch settings and
map NOR/NAND/ONENAND devices to right
chipselects
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Signed-off-by: David Brownell <david-b at pacbell.net>
Signed-off-by: Nishanth Menon <nm at ti.com>
Cc: Vikram Pandita <vikram.pandita at ti.com>
Cc: Richard Woodruff <r-woodruff2 at ti.com>
Cc: Sandeep Paulraj <s-paulraj at ti.com>
Cc: Tom Rix <tom.rix at windriver.com>
Cc: Dirk Behme <dirk.behme at googlemail.com>
---
MAINTAINERS | 1 +
MAKEALL | 1 +
Makefile | 3 +
board/ti/sdp3430/Makefile | 49 +++++
board/ti/sdp3430/config.mk | 33 +++
board/ti/sdp3430/sdp.c | 204 +++++++++++++++++++
board/ti/sdp3430/sdp.h | 417 +++++++++++++++++++++++++++++++++++++++
include/configs/omap3_sdp3430.h | 366 ++++++++++++++++++++++++++++++++++
8 files changed, 1074 insertions(+), 0 deletions(-)
create mode 100644 board/ti/sdp3430/Makefile
create mode 100644 board/ti/sdp3430/config.mk
create mode 100644 board/ti/sdp3430/sdp.c
create mode 100644 board/ti/sdp3430/sdp.h
create mode 100644 include/configs/omap3_sdp3430.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2297651..5742782 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -628,6 +628,7 @@ Guennadi Liakhovetski <g.liakhovetski at gmx.de>
Nishanth Menon <nm at ti.com>
+ omap3_sdp3430 ARM CORTEX-A8 (OMAP3xx SoC)
omap3_zoom1 ARM CORTEX-A8 (OMAP3xx SoC)
David Müller <d.mueller at elsoft.ch>
diff --git a/MAKEALL b/MAKEALL
index 38cd076..9bf75e8 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -603,6 +603,7 @@ LIST_ARM_CORTEX_A8=" \
omap3_overo \
omap3_evm \
omap3_pandora \
+ omap3_sdp3430 \
omap3_zoom1 \
omap3_zoom2 \
"
diff --git a/Makefile b/Makefile
index 9637643..8dbe552 100644
--- a/Makefile
+++ b/Makefile
@@ -3144,6 +3144,9 @@ omap3_zoom1_config : unconfig
omap3_zoom2_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 logicpd omap3
+omap3_sdp3430_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 sdp3430 ti omap3
+
#########################################################################
## XScale Systems
#########################################################################
diff --git a/board/ti/sdp3430/Makefile b/board/ti/sdp3430/Makefile
new file mode 100644
index 0000000..2554c7b
--- /dev/null
+++ b/board/ti/sdp3430/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := sdp.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ti/sdp3430/config.mk b/board/ti/sdp3430/config.mk
new file mode 100644
index 0000000..3726634
--- /dev/null
+++ b/board/ti/sdp3430/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2006-2009
+# Texas Instruments, <www.ti.com>
+#
+# OMAP 3430 SDP uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
diff --git a/board/ti/sdp3430/sdp.c b/board/ti/sdp3430/sdp.c
new file mode 100644
index 0000000..425fdfc
--- /dev/null
+++ b/board/ti/sdp3430/sdp.c
@@ -0,0 +1,204 @@
+/*
+ * (C) Copyright 2004-2009
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <twl4030.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include "sdp.h"
+
+const omap3_sysinfo sysinfo = {
+ DDR_DISCRETE,
+ "OMAP3 SDP3430 board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ "OneNAND",
+#elif defined(CONFIG_ENV_IS_IN_NAND)
+ "NAND",
+#else
+ "NOR",
+#endif
+};
+
+/* Timing definitions for GPMC controller for Sibley NOR */
+static const u32 gpmc_sdp_nor[] = {
+ SDP3430_NOR_GPMC_CONF1,
+ SDP3430_NOR_GPMC_CONF2,
+ SDP3430_NOR_GPMC_CONF3,
+ SDP3430_NOR_GPMC_CONF4,
+ SDP3430_NOR_GPMC_CONF5,
+ SDP3430_NOR_GPMC_CONF6,
+ /*CONF7- computed as params */
+};
+
+/*
+ * Timing definitions for GPMC controller for Debug Board
+ * Debug board contains access to ethernet and DIP Switch setting
+ * information etc.
+ */
+static const u32 gpmc_sdp_debug[] = {
+ SDP3430_DEBUG_GPMC_CONF1,
+ SDP3430_DEBUG_GPMC_CONF2,
+ SDP3430_DEBUG_GPMC_CONF3,
+ SDP3430_DEBUG_GPMC_CONF4,
+ SDP3430_DEBUG_GPMC_CONF5,
+ SDP3430_DEBUG_GPMC_CONF6,
+ /*CONF7- computed as params */
+};
+
+/* Timing defintions for GPMC OneNAND */
+static const u32 gpmc_sdp_onenand[] = {
+ SDP3430_ONENAND_GPMC_CONF1,
+ SDP3430_ONENAND_GPMC_CONF2,
+ SDP3430_ONENAND_GPMC_CONF3,
+ SDP3430_ONENAND_GPMC_CONF4,
+ SDP3430_ONENAND_GPMC_CONF5,
+ SDP3430_ONENAND_GPMC_CONF6,
+ /*CONF7- computed as params */
+};
+
+/* GPMC definitions for GPMC NAND */
+static const u32 gpmc_sdp_nand[] = {
+ SDP3430_NAND_GPMC_CONF1,
+ SDP3430_NAND_GPMC_CONF2,
+ SDP3430_NAND_GPMC_CONF3,
+ SDP3430_NAND_GPMC_CONF4,
+ SDP3430_NAND_GPMC_CONF5,
+ SDP3430_NAND_GPMC_CONF6,
+ /*CONF7- computed as params */
+};
+
+/* gpmc_cfg is initialized by gpmc_init and we use it here */
+extern struct gpmc *gpmc_cfg;
+
+/**
+ * @brief board_init - gpmc and basic setup as phase1 of boot sequence
+ *
+ * @return 0
+ */
+int board_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ /* TODO: Dynamically pop out CS mapping and program accordingly */
+ /* Configure devices for default ON ON ON settings */
+ enable_gpmc_cs_config(gpmc_sdp_nor, &gpmc_cfg->cs[0],
+ CONFIG_SYS_FLASH_BASE, GPMC_SIZE_128M);
+ enable_gpmc_cs_config(gpmc_sdp_nand, &gpmc_cfg->cs[1], 0x28000000,
+ GPMC_SIZE_16M);
+ enable_gpmc_cs_config(gpmc_sdp_onenand, &gpmc_cfg->cs[2], 0x20000000,
+ GPMC_SIZE_16M);
+ enable_gpmc_cs_config(gpmc_sdp_debug, &gpmc_cfg->cs[3], DEBUG_BASE,
+ GPMC_SIZE_16M);
+ /* board id for Linux */
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP_3430SDP;
+ /* boot param addr */
+ gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ return 0;
+}
+
+#define LAN_RESET_REGISTER (CONFIG_LAN91C96_BASE + 0x01c)
+#define ETH_CONTROL_REG (CONFIG_LAN91C96_BASE + 0x30b)
+
+/**
+ * @brief ether_init Take the Ethernet controller out of reset and wait
+ * for the EEPROM load to complete.
+ */
+static void ether_init(void)
+{
+#ifdef CONFIG_DRIVER_LAN91C96
+ int cnt = 20;
+
+ writew(0x0, LAN_RESET_REGISTER);
+ do {
+ writew(0x1, LAN_RESET_REGISTER);
+ udelay(100);
+ if (cnt == 0)
+ goto reset_err_out;
+ --cnt;
+ } while (readw(LAN_RESET_REGISTER) != 0x1);
+
+ cnt = 20;
+
+ do {
+ writew(0x0, LAN_RESET_REGISTER);
+ udelay(100);
+ if (cnt == 0)
+ goto reset_err_out;
+ --cnt;
+ } while (readw(LAN_RESET_REGISTER) != 0x0000);
+ udelay(1000);
+
+ writeb(readb(ETH_CONTROL_REG) & ~0x1, ETH_CONTROL_REG);
+ udelay(1000);
+reset_err_out:
+ return;
+
+#endif
+}
+
+/**
+ * @brief misc_init_r - Configure SDP board specific configurations
+ * such as power configurations, ethernet initialization as phase2 of
+ * boot sequence
+ *
+ * @return 0
+ */
+int misc_init_r(void)
+{
+ /* Partial setup:
+ * VAUX3 - 2.8V for DVI
+ * VPLL1 - 1.8V
+ * VDAC - 1.8V
+ * and turns on LEDA/LEDB (not needed ... NOP?)
+ */
+ twl4030_power_init();
+
+ /* FIXME finish setup:
+ * VAUX1 - 2.8V for mainboard I/O
+ * VAUX2 - 2.8V for camera
+ * VAUX4 - 1.8V for OMAP3 CSI
+ * VMMC1 - 3.15V (init, variable) for MMC1
+ * VMMC2 - 1.85V for MMC2
+ * VSIM - off (init, variable) for MMC1.DAT[3..7], SIM
+ * VPLL2 - 1.8V
+ */
+ ether_init();
+
+ return 0;
+}
+
+/**
+ * @brief set_muxconf_regs Setting up the configuration Mux registers
+ * specific to the hardware. Many pins need to be moved from protect
+ * to primary mode.
+ */
+void set_muxconf_regs(void)
+{
+ /* platform specific muxes */
+ MUX_SDP3430();
+}
diff --git a/board/ti/sdp3430/sdp.h b/board/ti/sdp3430/sdp.h
new file mode 100644
index 0000000..e2f604c
--- /dev/null
+++ b/board/ti/sdp3430/sdp.h
@@ -0,0 +1,417 @@
+/*
+ * (C) Copyright 2004-2006
+ * Texas Instruments
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _BOARD_SDP_H_
+#define _BOARD_SDP_H_
+
+#define OFF_IN_PD 0
+#define OFF_OUT_PD 0
+
+/*
+ * IEN - Input Enable
+ * IDIS - Input Disable
+ * PTD - Pull type Down
+ * PTU - Pull type Up
+ * DIS - Pull type selection is inactive
+ * EN - Pull type selection is active
+ * M0 - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_SDP3430()\
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0))\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A3), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A4), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A5), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A6), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A7), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A8), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A9), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_A10), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D8), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D9), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D10), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D11), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D12), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D13), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D14), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_D15), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NCS0), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_NCS1), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_NCS2), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_NCS3), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_NCS4), (OFF_IN_PD | IEN | PTU | EN | M4)) /*G55-F_DIS*/\
+ MUX_VAL(CP(GPMC_NCS5), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G56T_EN*/\
+ MUX_VAL(CP(GPMC_NCS6), (OFF_IN_PD | IEN | PTD | DIS | M4))/*G57-AGPSP*/\
+ MUX_VAL(CP(GPMC_NCS7), (OFF_IN_PD | IEN | PTU | EN | M4))/*G58-WLNIQ*/\
+ MUX_VAL(CP(GPMC_CLK), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NADV_ALE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NOE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NWE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NBE0_CLE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_NBE1), (OFF_IN_PD | IEN | PTD | DIS | M4)) /*G61-BTST*/\
+ MUX_VAL(CP(GPMC_NWP), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(GPMC_WAIT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_WAIT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(GPMC_WAIT2), (OFF_IN_PD | IEN | PTU | EN | M4)) /*GPIO_64*/\
+ MUX_VAL(CP(GPMC_WAIT3), (OFF_IN_PD | IEN | PTU | EN | M4)) /*GPIO_65*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_HSYNC), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_VSYNC), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_ACBIAS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA0), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA1), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA3), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA4), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA5), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA6), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA7), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA8), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA9), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA10), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA11), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA12), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA13), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA14), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA15), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA16), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA17), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA18), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA19), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA20), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA21), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA22), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(DSS_DATA23), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(CAM_VS), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(CAM_XCLKA), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_PCLK), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(CAM_FLD), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G98-C_RST*/\
+ MUX_VAL(CP(CAM_D0), (OFF_IN_PD | IEN | PTD | DIS | M2)) /*CAM_D0 */\
+ MUX_VAL(CP(CAM_D1), (OFF_IN_PD | IEN | PTD | DIS | M2)) /*CAM_D1 */\
+ MUX_VAL(CP(CAM_D2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D8), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D9), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D10), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_D11), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_XCLKB), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(CAM_WEN), (OFF_IN_PD | IEN | PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(CSI2_DX0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CSI2_DY0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CSI2_DX1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(CSI2_DY1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ /*Audio InterfACe */\
+ MUX_VAL(CP(MCBSP2_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP2_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP2_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP2_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ /*Expansion Card */\
+ MUX_VAL(CP(MMC1_CLK), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_CMD), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT2), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT3), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT4), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT5), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT6), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC1_DAT7), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MMC2_CMD), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC2_DAT0), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC2_DAT1), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC2_DAT2), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC2_DAT3), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MMC2_DAT4), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DRD0*/\
+ MUX_VAL(CP(MMC2_DAT5), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DRD1*/\
+ MUX_VAL(CP(MMC2_DAT6), (OFF_OUT_PD | IDIS | PTD | DIS | M1))/*DCMD*/\
+ MUX_VAL(CP(MMC2_DAT7), (OFF_IN_PD | IEN | PTU | EN | M1))/*CLKIN*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP3_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP3_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP3_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(UART2_CTS), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(UART2_RTS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(UART2_TX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(UART2_RX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(UART1_RTS), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(UART1_CTS), (OFF_IN_PD | IEN | PTU | DIS | M0))\
+ MUX_VAL(CP(UART1_RX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP4_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1DRX*/\
+ MUX_VAL(CP(MCBSP4_DR), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1FLGRX*/\
+ MUX_VAL(CP(MCBSP4_DX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1RDYRX*/\
+ MUX_VAL(CP(MCBSP4_FSX), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SSI1WAKE*/\
+ MUX_VAL(CP(MCBSP1_CLKR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP1_FSR), (OFF_OUT_PD | IDIS | PTU | EN | M4))/*G157BWP*/\
+ MUX_VAL(CP(MCBSP1_DX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP1_DR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP_CLKS), (OFF_IN_PD | IEN | PTU | DIS | M0))\
+ MUX_VAL(CP(MCBSP1_FSX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCBSP1_CLKX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(UART3_RTS_SD), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(UART3_RX_IRRX), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(UART3_TX_IRTX), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_STP), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(HSUSB0_DIR), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_NXT), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA3), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA4), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA5), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA6), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(HSUSB0_DATA7), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ /* NOTE db: removed off-mode from I2C 1/2/3 ... external pullups!! */\
+ MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0))\
+ MUX_VAL(CP(HDQ_SIO), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(MCSPI1_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI1_SIMO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI1_SOMI), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI1_CS0), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(MCSPI1_CS1), (OFF_OUT_PD | IDIS | PTD | EN | M0))\
+ MUX_VAL(CP(MCSPI1_CS2), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G176*/\
+ MUX_VAL(CP(MCSPI1_CS3), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(MCSPI2_CLK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI2_SIMO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI2_SOMI), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(MCSPI2_CS0), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(MCSPI2_CS1), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SYS_NIRQ), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(SYS_BOOT0), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G2PENIRQ*/\
+ MUX_VAL(CP(SYS_BOOT1), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*GPIO_3 */\
+ MUX_VAL(CP(SYS_BOOT2), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G4MMC1WP*/\
+ MUX_VAL(CP(SYS_BOOT3), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G5LCDENV*/\
+ MUX_VAL(CP(SYS_BOOT4), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G6LANINT*/\
+ MUX_VAL(CP(SYS_BOOT5), (OFF_OUT_PD | IEN | PTD | DIS | M4))/*G7MMC2WP*/\
+ MUX_VAL(CP(SYS_BOOT6), (OFF_OUT_PD | IDIS | PTD | DIS | M4))/*G8ENBKL*/\
+ MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SYS_CLKOUT2), (OFF_IN_PD | IEN | PTU | EN | M4))/*GPIO_186*/\
+ MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(JTAG_EMU0), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(JTAG_EMU1), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_CLK_ES2), (OFF_OUT_PD | IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(ETK_CTL_ES2), (OFF_OUT_PD | IDIS | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D0_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*USB1TLD0*/\
+ MUX_VAL(CP(ETK_D1_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*SPI3_CS0*/\
+ MUX_VAL(CP(ETK_D2_ES2), (OFF_IN_PD | IEN | PTD | EN | M1))/*USB1TLD2*/\
+ MUX_VAL(CP(ETK_D3_ES2), (OFF_IN_PD | IEN | PTD | DIS | M1))/*USB1TLD7*/\
+ MUX_VAL(CP(ETK_D4_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D5_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D6_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D7_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D8_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D9_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D10_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D11_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D12_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D13_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D14_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(ETK_D15_ES2), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ /*Die to Die */\
+ MUX_VAL(CP(D2D_MCAD0), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD1), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD2), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD3), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD4), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD5), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD6), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD7), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD8), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD9), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD10), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD11), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD12), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD13), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD14), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD15), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD16), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD17), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD18), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD19), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD20), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD21), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD22), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD23), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD24), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD25), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD26), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD27), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD28), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD29), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD30), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD31), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD32), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD33), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD34), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD35), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_MCAD36), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_CLK26MI), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_NRESPWRON), (OFF_OUT_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_NRESWARM), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(D2D_ARM9NIRQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_SPINT), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_FRINT), (OFF_IN_PD | IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_DMAREQ0), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_DMAREQ1), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_DMAREQ2), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_DMAREQ3), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GTRST), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GTDI), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GTDO), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GTMS), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GTCK), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_N3GRTCK), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_MSTDBY), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0))\
+ MUX_VAL(CP(D2D_IDLEREQ), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_IDLEACK), (OFF_IN_PD | IEN | PTU | EN | M0))\
+ MUX_VAL(CP(D2D_MWRITE), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_SWRITE), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_MREAD), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_SREAD), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_MBUSFLAG), (OFF_IN_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(D2D_SBUSFLAG), (OFF_OUT_PD | IEN | PTD | DIS | M0))\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0))\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7)) /*SDRC_CKE1 NOT USED*/
+
+/*
+ * GPMC Timing definitions for SDP3430
+ * at L3 = 166Mhz
+ */
+
+/* Timing definitions for GPMC controller for Sibley NOR */
+#define SDP3430_NOR_GPMC_CONF1 0x00001200
+#define SDP3430_NOR_GPMC_CONF2 0x001F1F00
+#define SDP3430_NOR_GPMC_CONF3 0x00080802
+#define SDP3430_NOR_GPMC_CONF4 0x1C091C09
+#define SDP3430_NOR_GPMC_CONF5 0x01131F1F
+#define SDP3430_NOR_GPMC_CONF6 0x1F0F03C2
+
+/*
+ * Timing definitions for GPMC controller for Debug Board
+ * Debug board contains access to ethernet and DIP Switch setting
+ * information etc.
+ */
+#define SDP3430_DEBUG_GPMC_CONF1 0x00611200
+#define SDP3430_DEBUG_GPMC_CONF2 0x001F1F01
+#define SDP3430_DEBUG_GPMC_CONF3 0x00080803
+#define SDP3430_DEBUG_GPMC_CONF4 0x1D091D09
+#define SDP3430_DEBUG_GPMC_CONF5 0x041D1F1F
+#define SDP3430_DEBUG_GPMC_CONF6 0x1D0904C4
+
+/* Timing defintions for GPMC OneNAND */
+#define SDP3430_ONENAND_GPMC_CONF1 0x00001200
+#define SDP3430_ONENAND_GPMC_CONF2 0x000F0F01
+#define SDP3430_ONENAND_GPMC_CONF3 0x00030301
+#define SDP3430_ONENAND_GPMC_CONF4 0x0F040F04
+#define SDP3430_ONENAND_GPMC_CONF5 0x010F1010
+#define SDP3430_ONENAND_GPMC_CONF6 0x1F060000
+
+/* GPMC definitions for GPMC NAND */
+#define SDP3430_NAND_GPMC_CONF1 0x00000800
+#define SDP3430_NAND_GPMC_CONF2 0x00141400
+#define SDP3430_NAND_GPMC_CONF3 0x00141400
+#define SDP3430_NAND_GPMC_CONF4 0x0F010F01
+#define SDP3430_NAND_GPMC_CONF5 0x010C1414
+#define SDP3430_NAND_GPMC_CONF6 0x1F040A80
+
+#endif /* _BOARD_SDP_H_ */
diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h
new file mode 100644
index 0000000..9e176b5
--- /dev/null
+++ b/include/configs/omap3_sdp3430.h
@@ -0,0 +1,366 @@
+/*
+ * (C) Copyright 2006-2009
+ * Texas Instruments.
+ * Richard Woodruff <r-woodruff2 at ti.com>
+ * Syed Mohammed Khasim <x0khasim at ti.com>
+ * Nishanth Menon <nm at ti.com>
+ *
+ * Configuration settings for the 3430 TI SDP3430 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP 1 /* in a TI OMAP core */
+#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP3430 1 /* which is in a 3430 */
+#define CONFIG_OMAP3_3430SDP 1 /* working with SDP Rev2 */
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * NOTE: these #defines presume standard SDP jumper settings.
+ * In particular:
+ * - 26 MHz clock (not 19.2 or 38.4 MHz)
+ * - Boot from 128MB NOR, not NAND or OneNAND
+ *
+ * At this writing, OMAP3 U-Boot support doesn't permit concurrent
+ * support for all the flash types the board supports.
+ */
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
+/* Clock Defines */
+#define V_OSCK 26000000 /* Clock output from T2 */
+#define V_SCLK (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ /* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
+
+/*
+ * Size of malloc() pool
+ * Total Size Environment - 128K
+ * Malloc - add 128K
+ */
+#define CONFIG_ENV_SIZE 0x00040000
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x00040000)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
+ /* initial data */
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * TWL4030
+ */
+#define CONFIG_TWL4030_POWER 1
+
+/*
+ * serial port - NS16550 compatible
+ */
+#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+
+/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
+ * swapped with UART2 via jumpering. Downsides of using J8: it doesn't
+ * support UART boot (that's only for UART3); it prevents sharing a Linux
+ * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
+ *
+ * UART boot uses UART3 on J9, and the SDP user's guide says to use
+ * that for console. Downsides of using J9: you can't use IRDA too;
+ * since UART3 isn't in the CORE power domain, it may be a bit less
+ * usable in certain PM-sensitive debug scenarios.
+ */
+#undef CONSOLE_J9 /* else J8/UART1 (innermost) */
+
+#ifdef CONSOLE_J9
+#define CONFIG_CONS_INDEX 3
+#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
+#define CONFIG_SERIAL3 3 /* UART3 */
+#else
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#define CONFIG_SERIAL1 1 /* UART1 */
+#endif
+
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
+ 115200}
+
+/*
+ * I2C for power management setup
+ */
+#define CONFIG_HARD_I2C 1
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_BUS 0
+#define CONFIG_SYS_I2C_BUS_SELECT 1
+#define CONFIG_DRIVER_OMAP34XX_I2C 1
+
+/* OMITTED: single 1 Gbit MT29F1G NAND flash */
+
+/*
+ * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
+ */
+#define CONFIG_SYS_FLASH_BASE 0x10000000
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_CFI 1 /* use CFI geometry data */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster writes */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware sector protection */
+#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* flinfo 'E' for empty */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
+
+#define CONFIG_SYS_FLASH_CFI_WIDTH 2
+#define PHYS_FLASH_SIZE 0x08000000 /* 128Meg */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors on one chip */
+
+/* timeout values are in milliseconds */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
+
+/* OMITTED: single 2 Gbit KFM2G16 OneNAND flash */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_SYS_ENV_SECT_SIZE 0x00040000 /* 256k */
+#define CONFIG_ENV_OFFSET CONFIG_SYS_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
+/*--------------------------------------------------------------------------*/
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+/* Enabled commands */
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NET
+
+/* Disabled commands */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+/*--------------------------------------------------------------------------*/
+/*
+ * MMC boot support
+ */
+
+#if defined(CONFIG_CMD_MMC)
+#define CONFIG_MMC 1
+#define CONFIG_OMAP3_MMC 1
+#define CONFIG_DOS_PARTITION 1
+#endif
+
+/*----------------------------------------------------------------------------
+ * SMSC9115 Ethernet from SMSC9118 family
+ *----------------------------------------------------------------------------
+ */
+#if defined(CONFIG_CMD_NET)
+
+#define CONFIG_DRIVER_LAN91C96
+#define CONFIG_LAN91C96_BASE DEBUG_BASE
+#define CONFIG_LAN91C96_EXT_PHY
+
+#define CONFIG_BOOTP_SEND_HOSTNAME
+/*
+ * BOOTP fields
+ */
+#define CONFIG_BOOTP_SUBNETMASK 0x00000001
+#define CONFIG_BOOTP_GATEWAY 0x00000002
+#define CONFIG_BOOTP_HOSTNAME 0x00000004
+#define CONFIG_BOOTP_BOOTPATH 0x00000010
+#endif /* (CONFIG_CMD_NET) */
+
+/*
+ * Environment setup
+ *
+ * Default boot order: mmc bootscript, MMC uImage, NOR image.
+ * Network booting environment must be configured at site.
+ */
+
+/* allow overwriting serial config and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyS0,115200n8\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "norargs=setenv bootargs console=${console} " \
+ "root=/dev/mtdblock3 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from MMC/SD ...; " \
+ "autoscr ${loadaddr}\0" \
+ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from MMC/SD ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "norboot=echo Booting from NOR ...; " \
+ "run norargs; " \
+ "bootm 0x80000\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmcinit; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run norboot; " \
+ "fi; " \
+ "fi; " \
+ "else run norboot; fi"
+
+#define CONFIG_AUTO_COMPLETE 1
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT "OMAP34XX SDP # "
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
+ * a basic sanity check ONLY
+ * IF you would like to increase coverage, increase the end address
+ * or run the test with custom options
+ */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x01000000)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + 0x02000000)
+
+/* Default load address */
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
+ * 32KHz clk, or from external sig. This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE 0x00020000 /* 128K - regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ 0x00001000 /* 4K - IRQ stack */
+#define CONFIG_STACKSIZE_FIQ 0x00001000 /* 4K - FIQ stack */
+#endif
+
+/*
+ * SDRAM Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE 0x02000000 /* at least 32 meg */
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C 1
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * NOR FLASH usage ... default nCS0:
+ * - one 256KB sector for U-Boot
+ * - one 256KB sector for its parameters (not all used)
+ * - eight sectors (2 MB) for kernel
+ * - rest for JFFS2
+ */
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256K */
+
+#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
+
+/*
+ * NAND FLASH usage ... default nCS1:
+ * - four 128KB sectors for X-Loader
+ * - four 128KB sectors for U-Boot
+ * - two 128KB sector for its parameters
+ * - 32 sectors (4 MB) for kernel
+ * - rest for filesystem
+ */
+
+/*
+ * OneNAND FLASH usage ... default nCS2:
+ * - four 128KB sectors for X-Loader
+ * - two 128KB sectors for U-Boot
+ * - one 128KB sector for its parameters
+ * - sixteen sectors (2 MB) for kernel
+ * - rest for filesystem
+ */
+
+/*--------------------------------------------------------------------------*/
+
+#ifndef __ASSEMBLY__
+extern struct gpmc *gpmc_cfg;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+#endif /* __CONFIG_H */
--
1.6.0.4
More information about the U-Boot
mailing list