[U-Boot] [PATCH v2 4/4] add TI DA8xx support: Integrate DA830 EVM support into U-Boot

Tom Tom.Rix at windriver.com
Sun Oct 25 02:23:05 CEST 2009


Nick Thompson wrote:
> Integrate DA830 EVM support into U-Boot.
> 
> Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
> Digital EVM board. See http://www.spectrumdigital.com/
> 
> Signed-off-by: Nick Thompson <nick.thompson at gefanuc.com>
> ---
> Applies to u-boot-ti
> 
>  MAINTAINERS                |    4 +
>  MAKEALL                    |    1 +
>  Makefile                   |    3 +
>  include/common.h           |    4 +
>  include/configs/da830evm.h |  244 ++++++++++++++++++++++++++++++++++++++++++++
>  5 files changed, 256 insertions(+), 0 deletions(-)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 528b963..88b4abd 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -712,6 +712,10 @@ Andrea Scian <andrea.scian at dave-tech.it>
>  
>  	B2		ARM7TDMI (S3C44B0X)
>  
> +Nick Thompson <nick.thompson at gefanuc.com>
> +
> +	da830evm	ARM926EJS (DA830/OMAP-L137)
> +
>  Albin Tonnerre <albin.tonnerre at free-electrons.com>
>  
>  	sbc35_a9g20	ARM926EJS (AT91SAM9G20 SoC)
> diff --git a/MAKEALL b/MAKEALL
> index 0a34a58..4d4350b 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -569,6 +569,7 @@ LIST_ARM9="			\
>  	davinci_dm355evm	\
>  	davinci_dm355leopard	\
>  	davinci_dm6467evm	\
> +	da830evm		\
>  "
>  
>  #########################################################################
> diff --git a/Makefile b/Makefile
> index 449099a..ab0469c 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -2936,6 +2936,9 @@ davinci_dm365evm_config :	unconfig
>  davinci_dm6467evm_config :	unconfig
>  	@$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci
>  
> +da830evm_config:	unconfig
> +	@$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci da8xx
> +
>  imx27lite_config:	unconfig
>  	@$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27
>  
> diff --git a/include/common.h b/include/common.h
> index f7c93bf..81cafab 100644
> --- a/include/common.h
> +++ b/include/common.h
> @@ -107,6 +107,10 @@ typedef volatile unsigned char	vu_char;
>  #ifdef CONFIG_BLACKFIN
>  #include <asm/blackfin.h>
>  #endif
> +#ifdef CONFIG_SOC_DA8XX
> +#include <asm/arch/hardware.h>
> +#endif
> +
>  
>  #include <part.h>
>  #include <flash.h>
> diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h
> new file mode 100644
> index 0000000..d974efd
> --- /dev/null
> +++ b/include/configs/da830evm.h
> @@ -0,0 +1,244 @@
> +/*
> + * Copyright (C) 2008 Texas Instruments, Inc <www.ti.com>
> + *
> + * Based on davinci_dvevm.h. Original Copyrights follow:
> + *
> + * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +#include <asm/sizes.h>
> +#include <asm/arch/clock.h>
> +
> +/*
> + * Board
> + */
> +
> +/*
> + * SoC Configuration
> + */
> +#define CONFIG_MACH_DAVINCI_DA830_EVM
> +#define CONFIG_ARM926EJS		/* arm926ejs CPU core */
> +#define CONFIG_SOC_DA8XX		/* TI DA8xx SoC */
> +#define CONFIG_SYS_CLK_FREQ 		clk_get(DAVINCI_ARM_CLKID)
Extra space at end of ..CLK_FREQ
optional fix

> +#define CONFIG_SYS_OSCIN_FREQ		24000000
> +#define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
> +#define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
> +#define CONFIG_SYS_HZ			1000
> +#undef CONFIG_SKIP_LOWLEVEL_INIT
> +#define CONFIG_SKIP_RELOCATE_UBOOT	/* to a proper address, init done */
> +
> +/*
> + * Memory Info
> + */
> +#define CONFIG_SYS_MALLOC_LEN	(0x10000 + 1*1024*1024) /* malloc() len */
> +#define CONFIG_SYS_GBL_DATA_SIZE	128 /* reserved for initial data */
> +#define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
> +#define PHYS_SDRAM_1_SIZE	0x04000000 /* SDRAM size 64MB */
> +#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1 /* memtest start addr */
> +#define CONFIG_SYS_MEMTEST_END 	(PHYS_SDRAM_1 + 16*1024*1024) /* 16MB test */
> +#define CONFIG_NR_DRAM_BANKS	1 /* we have 1 bank of DRAM */
> +#define CONFIG_STACKSIZE	(256*1024) /* regular stack */
> +
> +/*
> + * Serial Driver info
> + */
> +#define CONFIG_SYS_NS16550
> +#define CONFIG_SYS_NS16550_SERIAL
> +#define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size */
> +#define CONFIG_SYS_NS16550_COM1	DAVINCI_UART2_BASE /* Base address of UART2 */
> +#define CONFIG_SYS_NS16550_CLK	clk_get(DAVINCI_UART2_CLKID)
> +#define CONFIG_CONS_INDEX	1		/* use UART0 for console */
> +#define CONFIG_BAUDRATE		115200		/* Default baud rate */
> +#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
> +
> +/*
> + * I2C Configuration
> + */
> +#define CONFIG_HARD_I2C
> +#define CONFIG_DRIVER_DAVINCI_I2C
> +#define CONFIG_SYS_I2C_SPEED		25000 /* 100Kbps won't work, H/W bug */
> +#define CONFIG_SYS_I2C_SLAVE		10 /* Bogus, master-only in U-Boot */
> +
> +/*
> + * I2C EEPROM definitions for catalyst 24W256 EEPROM chip
> + */
> +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
> +#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
> +
> +/*
> + * Network & Ethernet Configuration
> + */
> +#ifdef CONFIG_DRIVER_TI_EMAC
> +#define CONFIG_MII
> +#define CONFIG_BOOTP_DEFAULT
> +#define CONFIG_BOOTP_DNS
> +#define CONFIG_BOOTP_DNS2
> +#define CONFIG_BOOTP_SEND_HOSTNAME
> +#define CONFIG_NET_RETRY_COUNT	10
> +#define CONFIG_NET_MULTI
> +#endif
> +
> +/*
> + * Flash & Environment
> + */
> +#ifdef CONFIG_USE_NAND
> +#undef CONFIG_ENV_IS_IN_FLASH
> +#define CONFIG_NAND_DAVINCI
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_ENV_IS_IN_NAND		/* U-Boot env in NAND Flash  */
> +#define CONFIG_ENV_OFFSET		0x0 /* Block 0--not used by bootcode */
> +#define CONFIG_ENV_SIZE			(128 << 10)
> +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
> +#define CONFIG_SYS_NAND_CS		3
> +#define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
> +#define CONFIG_SYS_CLE_MASK		0x10
> +#define CONFIG_SYS_ALE_MASK		0x8
> +#define CONFIG_SYS_NAND_HW_ECC
> +#define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
> +#define NAND_MAX_CHIPS			1
> +#define DEF_BOOTM			""
> +#endif
> +
> +#ifdef CONFIG_USE_NOR
> +#define CONFIG_ENV_IS_IN_FLASH
> +#undef CONFIG_SYS_NO_FLASH
> +#define CONFIG_SYS_FLASH_CFI_DRIVER
> +#define CONFIG_SYS_FLASH_CFI
> +#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* max number of flash banks */
> +#define CONFIG_SYS_FLASH_SECT_SZ	(64 << 10) /* 64KB */
> +#define CONFIG_ENV_OFFSET		(CONFIG_SYS_FLASH_SECT_SZ*3)
> +#define CONFIG_SYS_FLASH_BASE		DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
> +#define PHYS_FLASH_SIZE			(32 << 20) /* Flash size 32MB */
> +#define CONFIG_SYS_MAX_FLASH_SECT	(PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
> +#define CONFIG_ENV_SECT_SIZE		CONFIG_SYS_FLASH_SECT_SZ
> +#define CONFIG_SYS_FLASH_SPL_ACCESS
> +#endif
> +
> +#ifdef CONFIG_USE_SPIFLASH
> +#undef CONFIG_ENV_IS_IN_FLASH
> +#undef CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SIZE			(16 << 10)
> +#define CONFIG_ENV_OFFSET		(256 << 10)
> +#define CONFIG_ENV_SECT_SIZE		4096
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_SPI
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_WINBOND
> +#define CONFIG_DAVINCI_SPI
> +#define CONFIG_SYS_SPI_BASE		DAVINCI_SPI0_BASE
> +#define CONFIG_SYS_SPI_CLK		clk_get(DAVINCI_SPI0_CLKID)
> +#define CONFIG_SF_DEFAULT_SPEED		50000000
> +#define CONFIG_SYS_ENV_SPI_MAX_HZ	CONFIG_SF_DEFAULT_SPEED
> +#endif
> +
> +
> +/*
> + * U-Boot general configuration
> + */
> +#undef CONFIG_USE_IRQ			/* No IRQ/FIQ in U-Boot */
> +#undef CONFIG_MISC_INIT_R
> +#undef CONFIG_BOOTDELAY
> +#define CONFIG_BOOTFILE		"uImage" /* Boot file name */
> +#define CONFIG_SYS_PROMPT	"DA830-evm > " /* Command Prompt */
> +#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size	*/
> +#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
> +#define CONFIG_SYS_MAXARGS	16 /* max number of command args */
> +#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
> +#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_MEMTEST_START + 0x700000)
> +#define CONFIG_VERSION_VARIABLE
> +#define CONFIG_AUTO_COMPLETE	/* Won't work with hush so far, may be later */
> +#define CONFIG_SYS_HUSH_PARSER
> +#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_CRC32_VERIFY
> +#define CONFIG_MX_CYCLIC
> +#define CONFIG_USE_PINMUX
> +
> +/*
> + * Linux Information
> + */
> +#define LINUX_BOOT_PARAM_ADDR	(CONFIG_SYS_MEMTEST_START + 0x100)
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_BOOTARGS		"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp"
> +#define CONFIG_BOOTCOMMAND	""
> +#define CONFIG_BOOTDELAY	3
> +
> +/*
> + * U-Boot commands
> + */
> +#include <config_cmd_default.h>
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_ASKENV
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_DIAG
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_SAVES
> +#define CONFIG_CMD_MEMORY
> +#undef CONFIG_CMD_BDI
> +#undef CONFIG_CMD_FPGA
> +#undef CONFIG_CMD_SETGETDCR
> +#define CONFIG_CMD_EEPROM
> +
> +#ifndef CONFIG_DRIVER_TI_EMAC
> +#undef CONFIG_CMD_NET
> +#endif
> +
> +#ifdef CONFIG_USE_NAND
> +#undef CONFIG_CMD_FLASH
> +#undef CONFIG_CMD_IMLS
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_MTDPARTS
> +#define CONFIG_MTD_PARTITIONS
> +#define CONFIG_CMD_UBI
> +#define CONFIG_RBTREE
> +#endif
> +
> +#ifdef CONFIG_USE_SPIFLASH
> +#undef CONFIG_CMD_IMLS
> +#undef CONFIG_CMD_FLASH
> +#define CONFIG_CMD_SPI
> +#define CONFIG_CMD_SAVEENV
> +#endif
> +
> +#if !defined(CONFIG_USE_NAND) && \
> +	!defined(CONFIG_USE_NOR) && \
> +	!defined(CONFIG_USE_SPIFLASH)
> +#define CONFIG_ENV_IS_NOWHERE
> +#define CONFIG_SYS_NO_FLASH
> +#define CONFIG_ENV_SIZE		(16 << 10)
> +#undef CONFIG_CMD_IMLS
> +#undef CONFIG_CMD_FLASH
> +#undef CONFIG_CMD_ENV
> +#endif
> +
> +#ifdef CONFIG_USB_DA8XX
> +#define CONFIG_CMD_USB		/* include support for usb	*/
> +#define CONFIG_CMD_STORAGE	/* include support for usb	*/
> +#define CONFIG_CMD_FAT		/* include support for FAT/storage*/
> +#define CONFIG_DOS_PARTITION	/* include support for FAT/storage*/
> +#endif
> +
> +#endif /* __CONFIG_H */
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot

This is fine.
Ack-ed
Tom


More information about the U-Boot mailing list