[U-Boot] [PATCH v3 1/2] NET: Move MDIO regs out of TSEC Space

[Kumar Gopalpet-B05799]

>-----Original Message-----
>From: Phillips Kim-R1AAHA 
>Sent: Thursday, October 29, 2009 1:36 AM
>To: Kumar Gopalpet-B05799
>Cc: u-boot at lists.denx.de
>Subject: Re: [PATCH v3 1/2] NET: Move MDIO regs out of TSEC Space
>
>On Wed, 28 Oct 2009 14:19:18 +0530
>Sandeep Gopalpet <sandeep.kumar at freescale.com> wrote:
>
>> Moved the mdio regs out of the tsec structure,and provided different 
>> offsets for tsec base and mdio base so that provision for 
>etsec2.0 can 
>> be provided.
>> 
>> This patch helps in providing the support for etsec2.0 In etsec2.0, 
>> the MDIO register space and the etsec reg space are different.
>> 
>> Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into 
>> platform specific files.
>> 
>> Signed-off-by: Sandeep Gopalpet <sandeep.kumar at freescale.com>
>> ---
>
>without this patchseries:
>
>U-Boot 2009.11-rc1 (Oct 28 2009 - 14:57:54) MPC83XX
>
>Reset Status: Software Hard, External/Internal Soft, 
>External/Internal Hard
>
>CPU:   e300c3, MPC8315E, Rev: 1.0 at 400 MHz, CSB: 133.333 MHz
>Board: Freescale MPC8315ERDB Rev 0.1
>I2C:   ready
>DRAM:  128 MB
>FLASH:  8 MB
>NAND:  32 MiB
>PCIE0: No link
>PCIE1: No link
>In:    serial
>Out:   serial
>Err:   serial
>Net:   eTSEC0, eTSEC1
>Hit any key to stop autoboot:  0
>=> ping $serverip
>Speed: 1000, full duplex
>Using eTSEC0 device
>host 192.168.1.1 is alive
>=> 
>
>with this patchseries:
>
>U-Boot 2009.11-rc1-00002-g3775d27 (Oct 28 2009 - 14:45:51) MPC83XX
>
>Reset Status: Software Hard, External/Internal Soft, 
>External/Internal Hard
>
>CPU:   e300c3, MPC8315E, Rev: 1.0 at 400 MHz, CSB: 133.333 MHz
>Board: Freescale MPC8315ERDB Rev 0.1
>I2C:   ready
>DRAM:  128 MB
>FLASH:  8 MB
>NAND:  32 MiB
>PCIE0: No link
>PCIE1: No link
>In:    serial
>Out:   serial
>Err:   serial
>Net:   eTSEC0: No support for PHY id 0; assuming generic
>eTSEC1: No support for PHY id 0; assuming generic eTSEC0, 
>eTSEC1 Hit any key to stop autoboot:  0 => ping $serverip
>eTSEC0: No link.
>eTSEC1: No link.
>ping failed; host 192.168.1.1 is not alive
>
>do you not test older version tsecs/83xx?
>
>> +typedef struct tsec_mdio
>> +{
>
>please also move this brace onto the above line.


My bad. I forgot to change the MDIO_OFFSET in the last version of my
patches.
This is the reason why it failed for 83xx series.

Will resend the patches.

Thanks a lot Kim.


-Thanks
Sandeep