[U-Boot] [PATCH v2] include/linux/mii.h: update for supporting GE

Macpaul Lin macpaul at andestech.com
Fri Dec 3 06:52:34 CET 2010


This file has been synced (copy) from Linux source code.
This commit was based on kernel 2.6.32.
It updates gigabit related phy registers and basic definitions.

Signed-off-by: Macpaul Lin <macpaul at andestech.com>
---
Change v1: pull header file from Linux.
Change v2: clean up unused code for u-boot.

 include/linux/mii.h |  181 ++++++++++++++++++++++++++++++---------------------
 1 files changed, 107 insertions(+), 74 deletions(-)

diff --git a/include/linux/mii.h b/include/linux/mii.h
index 7c63095..6e7ffab 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -10,98 +10,132 @@
 
 /* Generic MII registers. */
 
-#define MII_BMCR	    0x00	/* Basic mode control register */
-#define MII_BMSR	    0x01	/* Basic mode status register  */
-#define MII_PHYSID1	    0x02	/* PHYS ID 1		       */
-#define MII_PHYSID2	    0x03	/* PHYS ID 2		       */
-#define MII_ADVERTISE	    0x04	/* Advertisement control reg   */
-#define MII_LPA		    0x05	/* Link partner ability reg    */
-#define MII_EXPANSION	    0x06	/* Expansion register	       */
-#define MII_DCOUNTER	    0x12	/* Disconnect counter	       */
-#define MII_FCSCOUNTER	    0x13	/* False carrier counter       */
-#define MII_NWAYTEST	    0x14	/* N-way auto-neg test reg     */
-#define MII_RERRCOUNTER     0x15	/* Receive error counter       */
-#define MII_SREVISION	    0x16	/* Silicon revision	       */
-#define MII_RESV1	    0x17	/* Reserved...		       */
-#define MII_LBRERROR	    0x18	/* Lpback, rx, bypass error    */
-#define MII_PHYADDR	    0x19	/* PHY address		       */
-#define MII_RESV2	    0x1a	/* Reserved...		       */
-#define MII_TPISTATUS	    0x1b	/* TPI status for 10mbps       */
-#define MII_NCONFIG	    0x1c	/* Network interface config    */
+#define MII_BMCR            0x00        /* Basic mode control register */
+#define MII_BMSR            0x01        /* Basic mode status register  */
+#define MII_PHYSID1         0x02        /* PHYS ID 1                   */
+#define MII_PHYSID2         0x03        /* PHYS ID 2                   */
+#define MII_ADVERTISE       0x04        /* Advertisement control reg   */
+#define MII_LPA             0x05        /* Link partner ability reg    */
+#define MII_EXPANSION       0x06        /* Expansion register          */
+#define MII_CTRL1000        0x09        /* 1000BASE-T control          */
+#define MII_STAT1000        0x0a        /* 1000BASE-T status           */
+#define MII_ESTATUS	    0x0f	/* Extended Status */
+#define MII_DCOUNTER        0x12        /* Disconnect counter          */
+#define MII_FCSCOUNTER      0x13        /* False carrier counter       */
+#define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
+#define MII_RERRCOUNTER     0x15        /* Receive error counter       */
+#define MII_SREVISION       0x16        /* Silicon revision            */
+#define MII_RESV1           0x17        /* Reserved...                 */
+#define MII_LBRERROR        0x18        /* Lpback, rx, bypass error    */
+#define MII_PHYADDR         0x19        /* PHY address                 */
+#define MII_RESV2           0x1a        /* Reserved...                 */
+#define MII_TPISTATUS       0x1b        /* TPI status for 10mbps       */
+#define MII_NCONFIG         0x1c        /* Network interface config    */
 
 /* Basic mode control register. */
-#define BMCR_RESV		0x003f	/* Unused...		       */
-#define BMCR_SPEED1000		0x0040	/* MSB of Speed (1000)	       */
-#define BMCR_CTST		0x0080	/* Collision test	       */
-#define BMCR_FULLDPLX		0x0100	/* Full duplex		       */
-#define BMCR_ANRESTART		0x0200	/* Auto negotiation restart    */
-#define BMCR_ISOLATE		0x0400	/* Disconnect DP83840 from MII */
-#define BMCR_PDOWN		0x0800	/* Powerdown the DP83840       */
-#define BMCR_ANENABLE		0x1000	/* Enable auto negotiation     */
-#define BMCR_SPEED100		0x2000	/* Select 100Mbps	       */
-#define BMCR_LOOPBACK		0x4000	/* TXD loopback bits	       */
-#define BMCR_RESET		0x8000	/* Reset the DP83840	       */
+#define BMCR_RESV               0x003f  /* Unused...                   */
+#define BMCR_SPEED1000		0x0040  /* MSB of Speed (1000)         */
+#define BMCR_CTST               0x0080  /* Collision test              */
+#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
+#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
+#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
+#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
+#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
+#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
+#define BMCR_RESET              0x8000  /* Reset the DP83840           */
 
 /* Basic mode status register. */
-#define BMSR_ERCAP		0x0001	/* Ext-reg capability	       */
-#define BMSR_JCD		0x0002	/* Jabber detected	       */
-#define BMSR_LSTATUS		0x0004	/* Link status		       */
-#define BMSR_ANEGCAPABLE	0x0008	/* Able to do auto-negotiation */
-#define BMSR_RFAULT		0x0010	/* Remote fault detected       */
-#define BMSR_ANEGCOMPLETE	0x0020	/* Auto-negotiation complete   */
-#define BMSR_RESV		0x07c0	/* Unused...		       */
-#define BMSR_10HALF		0x0800	/* Can do 10mbps, half-duplex  */
-#define BMSR_10FULL		0x1000	/* Can do 10mbps, full-duplex  */
-#define BMSR_100HALF		0x2000	/* Can do 100mbps, half-duplex */
-#define BMSR_100FULL		0x4000	/* Can do 100mbps, full-duplex */
-#define BMSR_100BASE4		0x8000	/* Can do 100mbps, 4k packets  */
+#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
+#define BMSR_JCD                0x0002  /* Jabber detected             */
+#define BMSR_LSTATUS            0x0004  /* Link status                 */
+#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
+#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
+#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
+#define BMSR_RESV               0x00c0  /* Unused...                   */
+#define BMSR_ESTATEN		0x0100	/* Extended Status in R15 */
+#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX */
+#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX */
+#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
+#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
+#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
 
 /* Advertisement control register. */
-#define ADVERTISE_SLCT		0x001f	/* Selector bits	       */
-#define ADVERTISE_CSMA		0x0001	/* Only selector supported     */
-#define ADVERTISE_10HALF	0x0020	/* Try for 10mbps half-duplex  */
-#define ADVERTISE_10FULL	0x0040	/* Try for 10mbps full-duplex  */
-#define ADVERTISE_100HALF	0x0080	/* Try for 100mbps half-duplex */
-#define ADVERTISE_100FULL	0x0100	/* Try for 100mbps full-duplex */
-#define ADVERTISE_100BASE4	0x0200	/* Try for 100mbps 4k packets  */
-#define ADVERTISE_RESV		0x1c00	/* Unused...		       */
-#define ADVERTISE_RFAULT	0x2000	/* Say we can detect faults    */
-#define ADVERTISE_LPACK		0x4000	/* Ack link partners response  */
-#define ADVERTISE_NPAGE		0x8000	/* Next page bit	       */
+#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
+#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
+#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
+#define ADVERTISE_1000XFULL     0x0020  /* Try for 1000BASE-X full-duplex */
+#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
+#define ADVERTISE_1000XHALF     0x0040  /* Try for 1000BASE-X half-duplex */
+#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
+#define ADVERTISE_1000XPAUSE    0x0080  /* Try for 1000BASE-X pause    */
+#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
+#define ADVERTISE_1000XPSE_ASYM 0x0100  /* Try for 1000BASE-X asym pause */
+#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
+#define ADVERTISE_PAUSE_CAP     0x0400  /* Try for pause               */
+#define ADVERTISE_PAUSE_ASYM    0x0800  /* Try for asymetric pause     */
+#define ADVERTISE_RESV          0x1000  /* Unused...                   */
+#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
+#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
+#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
 
 #define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
 			ADVERTISE_CSMA)
 #define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
-		       ADVERTISE_100HALF | ADVERTISE_100FULL)
+                       ADVERTISE_100HALF | ADVERTISE_100FULL)
 
 /* Link partner ability register. */
-#define LPA_SLCT		0x001f	/* Same as advertise selector  */
-#define LPA_10HALF		0x0020	/* Can do 10mbps half-duplex   */
-#define LPA_10FULL		0x0040	/* Can do 10mbps full-duplex   */
-#define LPA_100HALF		0x0080	/* Can do 100mbps half-duplex  */
-#define LPA_100FULL		0x0100	/* Can do 100mbps full-duplex  */
-#define LPA_100BASE4		0x0200	/* Can do 100mbps 4k packets   */
-#define LPA_RESV		0x1c00	/* Unused...		       */
-#define LPA_RFAULT		0x2000	/* Link partner faulted        */
-#define LPA_LPACK		0x4000	/* Link partner acked us       */
-#define LPA_NPAGE		0x8000	/* Next page bit	       */
+#define LPA_SLCT                0x001f  /* Same as advertise selector  */
+#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
+#define LPA_1000XFULL           0x0020  /* Can do 1000BASE-X full-duplex */
+#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
+#define LPA_1000XHALF           0x0040  /* Can do 1000BASE-X half-duplex */
+#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
+#define LPA_1000XPAUSE          0x0080  /* Can do 1000BASE-X pause     */
+#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
+#define LPA_1000XPAUSE_ASYM     0x0100  /* Can do 1000BASE-X pause asym*/
+#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
+#define LPA_PAUSE_CAP           0x0400  /* Can pause                   */
+#define LPA_PAUSE_ASYM          0x0800  /* Can pause asymetrically     */
+#define LPA_RESV                0x1000  /* Unused...                   */
+#define LPA_RFAULT              0x2000  /* Link partner faulted        */
+#define LPA_LPACK               0x4000  /* Link partner acked us       */
+#define LPA_NPAGE               0x8000  /* Next page bit               */
 
 #define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
 #define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
 
 /* Expansion register for auto-negotiation. */
-#define EXPANSION_NWAY		0x0001	/* Can do N-way auto-nego      */
-#define EXPANSION_LCWP		0x0002	/* Got new RX page code word   */
-#define EXPANSION_ENABLENPAGE	0x0004	/* This enables npage words    */
-#define EXPANSION_NPCAPABLE	0x0008	/* Link partner supports npage */
-#define EXPANSION_MFAULTS	0x0010	/* Multiple faults detected    */
-#define EXPANSION_RESV		0xffe0	/* Unused...		       */
+#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
+#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
+#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
+#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
+#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
+#define EXPANSION_RESV          0xffe0  /* Unused...                   */
+
+#define ESTATUS_1000_TFULL	0x2000	/* Can do 1000BT Full */
+#define ESTATUS_1000_THALF	0x1000	/* Can do 1000BT Half */
 
 /* N-way test register. */
-#define NWAYTEST_RESV1		0x00ff	/* Unused...		       */
-#define NWAYTEST_LOOPBACK	0x0100	/* Enable loopback for N-way   */
-#define NWAYTEST_RESV2		0xfe00	/* Unused...		       */
+#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
+#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
+#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
+
+/* 1000BASE-T Control register */
+#define ADVERTISE_1000FULL      0x0200  /* Advertise 1000BASE-T full duplex */
+#define ADVERTISE_1000HALF      0x0100  /* Advertise 1000BASE-T half duplex */
 
+/* 1000BASE-T Status register */
+#define LPA_1000LOCALRXOK       0x2000  /* Link partner local receiver status */
+#define LPA_1000REMRXOK         0x1000  /* Link partner remote receiver status */
+#define LPA_1000FULL            0x0800  /* Link partner 1000BASE-T full duplex */
+#define LPA_1000HALF            0x0400  /* Link partner 1000BASE-T half duplex */
+
+/* Flow control flags */
+#define FLOW_CTRL_TX		0x01
+#define FLOW_CTRL_RX		0x02
 
 /**
  * mii_nway_result
@@ -114,7 +148,7 @@
  *
  * The one exception to IEEE 802.3u is that 100baseT4 is placed
  * between 100T-full and 100T-half.  If your phy does not support
- * 100T4 this is fine.	If your phy places 100T4 elsewhere in the
+ * 100T4 this is fine. If your phy places 100T4 elsewhere in the
  * priority order, you will need to roll your own function.
  */
 static inline unsigned int mii_nway_result (unsigned int negotiated)
@@ -154,5 +188,4 @@ static inline unsigned int mii_duplex (unsigned int duplex_lock,
 	return 0;
 }
 
-
 #endif /* __LINUX_MII_H__ */
-- 
1.7.3.2



More information about the U-Boot mailing list