[U-Boot] [PATCH v4 2/7] this is jz4740 head file
Xiangfu Liu
xiangfu at openmobilefree.net
Wed Dec 8 07:20:44 CET 2010
Signed-off-by: Xiangfu Liu <xiangfu at openmobilefree.net>
---
arch/mips/include/asm/jz4740.h | 1380 ++++++++++++++++++++++++++++++++++++++++
1 files changed, 1380 insertions(+), 0 deletions(-)
create mode 100644 arch/mips/include/asm/jz4740.h
diff --git a/arch/mips/include/asm/jz4740.h b/arch/mips/include/asm/jz4740.h
new file mode 100644
index 0000000..5be26dc
--- /dev/null
+++ b/arch/mips/include/asm/jz4740.h
@@ -0,0 +1,1380 @@
+/*
+ * Include file for Ingenic Semiconductor's JZ4740 CPU.
+ */
+#ifndef __JZ4740_H__
+#define __JZ4740_H__
+
+#include <asm/addrspace.h>
+#include <asm/cacheops.h>
+
+/* Boot ROM Specification */
+/* NOR Boot config */
+#define JZ4740_NORBOOT_8BIT 0x00000000 /* 8-bit data bus flash */
+#define JZ4740_NORBOOT_16BIT 0x10101010 /* 16-bit data bus flash */
+#define JZ4740_NORBOOT_32BIT 0x20202020 /* 32-bit data bus flash */
+/* NAND Boot config */
+#define JZ4740_NANDBOOT_B8R3 0xffffffff /* 8-bit bus & 3 row cycles */
+#define JZ4740_NANDBOOT_B8R2 0xf0f0f0f0 /* 8-bit bus & 2 row cycles */
+#define JZ4740_NANDBOOT_B16R3 0x0f0f0f0f /* 16-bit bus & 3 row cycles */
+#define JZ4740_NANDBOOT_B16R2 0x00000000 /* 16-bit bus & 2 row cycles */
+
+/* Register Definitions */
+#define CPM_BASE 0xB0000000
+#define INTC_BASE 0xB0001000
+#define TCU_BASE 0xB0002000
+#define WDT_BASE 0xB0002000
+#define RTC_BASE 0xB0003000
+#define GPIO_BASE 0xB0010000
+#define AIC_BASE 0xB0020000
+#define ICDC_BASE 0xB0020000
+#define MSC_BASE 0xB0021000
+#define UART0_BASE 0xB0030000
+#define I2C_BASE 0xB0042000
+#define SSI_BASE 0xB0043000
+#define SADC_BASE 0xB0070000
+#define EMC_BASE 0xB3010000
+#define DMAC_BASE 0xB3020000
+#define UHC_BASE 0xB3030000
+#define UDC_BASE 0xB3040000
+#define LCD_BASE 0xB3050000
+#define SLCD_BASE 0xB3050000
+#define CIM_BASE 0xB3060000
+#define ETH_BASE 0xB3100000
+
+/*
+ * INTC (Interrupt Controller)
+ */
+#define INTC_ISR (INTC_BASE + 0x00)
+#define INTC_IMR (INTC_BASE + 0x04)
+#define INTC_IMSR (INTC_BASE + 0x08)
+#define INTC_IMCR (INTC_BASE + 0x0c)
+#define INTC_IPR (INTC_BASE + 0x10)
+
+
+/* 1st-level interrupts */
+#define IRQ_I2C 1
+#define IRQ_UHC 3
+#define IRQ_UART0 9
+#define IRQ_SADC 12
+#define IRQ_MSC 14
+#define IRQ_RTC 15
+#define IRQ_SSI 16
+#define IRQ_CIM 17
+#define IRQ_AIC 18
+#define IRQ_ETH 19
+#define IRQ_DMAC 20
+#define IRQ_TCU2 21
+#define IRQ_TCU1 22
+#define IRQ_TCU0 23
+#define IRQ_UDC 24
+#define IRQ_GPIO3 25
+#define IRQ_GPIO2 26
+#define IRQ_GPIO1 27
+#define IRQ_GPIO0 28
+#define IRQ_IPU 29
+#define IRQ_LCD 30
+
+/* 2nd-level interrupts */
+#define IRQ_DMA_0 32 /* 32 to 37 for DMAC channel 0 to 5 */
+#define IRQ_GPIO_0 48 /* 48 to 175 for GPIO pin 0 to 127 */
+
+/*
+ * RTC
+ */
+#define RTC_RCR (RTC_BASE + 0x00) /* RTC Control Register */
+#define RTC_RSR (RTC_BASE + 0x04) /* RTC Second Register */
+#define RTC_RSAR (RTC_BASE + 0x08) /* RTC Second Alarm Register */
+#define RTC_RGR (RTC_BASE + 0x0c) /* RTC Regulator Register */
+
+#define RTC_HCR (RTC_BASE + 0x20) /* Hibernate Control Register */
+#define RTC_HWFCR (RTC_BASE + 0x24) /* Hibernate Wakeup Filter Counter Reg */
+#define RTC_HRCR (RTC_BASE + 0x28) /* Hibernate Reset Counter Register */
+#define RTC_HWCR (RTC_BASE + 0x2c) /* Hibernate Wakeup Control Register */
+#define RTC_HWRSR (RTC_BASE + 0x30) /* Hibernate Wakeup Status Register */
+#define RTC_HSPR (RTC_BASE + 0x34) /* Hibernate Scratch Pattern Register */
+
+
+/* RTC Control Register */
+#define RTC_RCR_WRDY (1 << 7) /* Write Ready Flag */
+#define RTC_RCR_HZ (1 << 6) /* 1Hz Flag */
+#define RTC_RCR_HZIE (1 << 5) /* 1Hz Interrupt Enable */
+#define RTC_RCR_AF (1 << 4) /* Alarm Flag */
+#define RTC_RCR_AIE (1 << 3) /* Alarm Interrupt Enable */
+#define RTC_RCR_AE (1 << 2) /* Alarm Enable */
+#define RTC_RCR_RTCE (1 << 0) /* RTC Enable */
+
+/* RTC Regulator Register */
+#define RTC_RGR_LOCK (1 << 31) /* Lock Bit */
+#define RTC_RGR_ADJC_BIT 16
+#define RTC_RGR_ADJC_MASK (0x3ff << RTC_RGR_ADJC_BIT)
+#define RTC_RGR_NC1HZ_BIT 0
+#define RTC_RGR_NC1HZ_MASK (0xffff << RTC_RGR_NC1HZ_BIT)
+
+/* Hibernate Control Register */
+#define RTC_HCR_PD (1 << 0) /* Power Down */
+
+/* Hibernate Wakeup Filter Counter Register */
+#define RTC_HWFCR_BIT 5
+#define RTC_HWFCR_MASK (0x7ff << RTC_HWFCR_BIT)
+
+/* Hibernate Reset Counter Register */
+#define RTC_HRCR_BIT 5
+#define RTC_HRCR_MASK (0x7f << RTC_HRCR_BIT)
+
+/* Hibernate Wakeup Control Register */
+#define RTC_HWCR_EALM (1 << 0) /* RTC alarm wakeup enable */
+
+/* Hibernate Wakeup Status Register */
+#define RTC_HWRSR_HR (1 << 5) /* Hibernate reset */
+#define RTC_HWRSR_PPR (1 << 4) /* PPR reset */
+#define RTC_HWRSR_PIN (1 << 1) /* Wakeup pin status bit */
+#define RTC_HWRSR_ALM (1 << 0) /* RTC alarm status bit */
+
+/*
+ * CPM (Clock reset and Power control Management)
+ */
+#define CPM_CPCCR (CPM_BASE+0x00)
+#define CPM_CPPCR (CPM_BASE+0x10)
+#define CPM_I2SCDR (CPM_BASE+0x60)
+#define CPM_LPCDR (CPM_BASE+0x64)
+#define CPM_MSCCDR (CPM_BASE+0x68)
+#define CPM_UHCCDR (CPM_BASE+0x6C)
+
+#define CPM_LCR (CPM_BASE+0x04)
+#define CPM_CLKGR (CPM_BASE+0x20)
+#define CPM_SCR (CPM_BASE+0x24)
+
+#define CPM_HCR (CPM_BASE+0x30)
+#define CPM_HWFCR (CPM_BASE+0x34)
+#define CPM_HRCR (CPM_BASE+0x38)
+#define CPM_HWCR (CPM_BASE+0x3c)
+#define CPM_HWSR (CPM_BASE+0x40)
+#define CPM_HSPR (CPM_BASE+0x44)
+
+#define CPM_RSR (CPM_BASE+0x08)
+
+/* Clock Control Register */
+#define CPM_CPCCR_I2CS (1 << 31)
+#define CPM_CPCCR_CLKOEN (1 << 30)
+#define CPM_CPCCR_UCS (1 << 29)
+#define CPM_CPCCR_UDIV_BIT 23
+#define CPM_CPCCR_UDIV_MASK (0x3f << CPM_CPCCR_UDIV_BIT)
+#define CPM_CPCCR_CE (1 << 22)
+#define CPM_CPCCR_PCS (1 << 21)
+#define CPM_CPCCR_LDIV_BIT 16
+#define CPM_CPCCR_LDIV_MASK (0x1f << CPM_CPCCR_LDIV_BIT)
+#define CPM_CPCCR_MDIV_BIT 12
+#define CPM_CPCCR_MDIV_MASK (0x0f << CPM_CPCCR_MDIV_BIT)
+#define CPM_CPCCR_PDIV_BIT 8
+#define CPM_CPCCR_PDIV_MASK (0x0f << CPM_CPCCR_PDIV_BIT)
+#define CPM_CPCCR_HDIV_BIT 4
+#define CPM_CPCCR_HDIV_MASK (0x0f << CPM_CPCCR_HDIV_BIT)
+#define CPM_CPCCR_CDIV_BIT 0
+#define CPM_CPCCR_CDIV_MASK (0x0f << CPM_CPCCR_CDIV_BIT)
+
+/* I2S Clock Divider Register */
+#define CPM_I2SCDR_I2SDIV_BIT 0
+#define CPM_I2SCDR_I2SDIV_MASK (0x1ff << CPM_I2SCDR_I2SDIV_BIT)
+
+/* LCD Pixel Clock Divider Register */
+#define CPM_LPCDR_PIXDIV_BIT 0
+#define CPM_LPCDR_PIXDIV_MASK (0x1ff << CPM_LPCDR_PIXDIV_BIT)
+
+/* MSC Clock Divider Register */
+#define CPM_MSCCDR_MSCDIV_BIT 0
+#define CPM_MSCCDR_MSCDIV_MASK (0x1f << CPM_MSCCDR_MSCDIV_BIT)
+
+/* PLL Control Register */
+#define CPM_CPPCR_PLLM_BIT 23
+#define CPM_CPPCR_PLLM_MASK (0x1ff << CPM_CPPCR_PLLM_BIT)
+#define CPM_CPPCR_PLLN_BIT 18
+#define CPM_CPPCR_PLLN_MASK (0x1f << CPM_CPPCR_PLLN_BIT)
+#define CPM_CPPCR_PLLOD_BIT 16
+#define CPM_CPPCR_PLLOD_MASK (0x03 << CPM_CPPCR_PLLOD_BIT)
+#define CPM_CPPCR_PLLS (1 << 10)
+#define CPM_CPPCR_PLLBP (1 << 9)
+#define CPM_CPPCR_PLLEN (1 << 8)
+#define CPM_CPPCR_PLLST_BIT 0
+#define CPM_CPPCR_PLLST_MASK (0xff << CPM_CPPCR_PLLST_BIT)
+
+/* Low Power Control Register */
+#define CPM_LCR_DOZE_DUTY_BIT 3
+#define CPM_LCR_DOZE_DUTY_MASK (0x1f << CPM_LCR_DOZE_DUTY_BIT)
+#define CPM_LCR_DOZE_ON (1 << 2)
+#define CPM_LCR_LPM_BIT 0
+#define CPM_LCR_LPM_MASK (0x3 << CPM_LCR_LPM_BIT)
+ #define CPM_LCR_LPM_IDLE (0x0 << CPM_LCR_LPM_BIT)
+ #define CPM_LCR_LPM_SLEEP (0x1 << CPM_LCR_LPM_BIT)
+
+/* Clock Gate Register */
+#define CPM_CLKGR_UART1 (1 << 15)
+#define CPM_CLKGR_UHC (1 << 14)
+#define CPM_CLKGR_IPU (1 << 13)
+#define CPM_CLKGR_DMAC (1 << 12)
+#define CPM_CLKGR_UDC (1 << 11)
+#define CPM_CLKGR_LCD (1 << 10)
+#define CPM_CLKGR_CIM (1 << 9)
+#define CPM_CLKGR_SADC (1 << 8)
+#define CPM_CLKGR_MSC (1 << 7)
+#define CPM_CLKGR_AIC1 (1 << 6)
+#define CPM_CLKGR_AIC2 (1 << 5)
+#define CPM_CLKGR_SSI (1 << 4)
+#define CPM_CLKGR_I2C (1 << 3)
+#define CPM_CLKGR_RTC (1 << 2)
+#define CPM_CLKGR_TCU (1 << 1)
+#define CPM_CLKGR_UART0 (1 << 0)
+
+/* Sleep Control Register */
+#define CPM_SCR_O1ST_BIT 8
+#define CPM_SCR_O1ST_MASK (0xff << CPM_SCR_O1ST_BIT)
+#define CPM_SCR_UDCPHY_ENABLE (1 << 6)
+#define CPM_SCR_USBPHY_DISABLE (1 << 7)
+#define CPM_SCR_OSC_ENABLE (1 << 4)
+
+/* Hibernate Control Register */
+#define CPM_HCR_PD (1 << 0)
+
+/* Wakeup Filter Counter Register in Hibernate Mode */
+#define CPM_HWFCR_TIME_BIT 0
+#define CPM_HWFCR_TIME_MASK (0x3ff << CPM_HWFCR_TIME_BIT)
+
+/* Reset Counter Register in Hibernate Mode */
+#define CPM_HRCR_TIME_BIT 0
+#define CPM_HRCR_TIME_MASK (0x7f << CPM_HRCR_TIME_BIT)
+
+/* Wakeup Control Register in Hibernate Mode */
+#define CPM_HWCR_WLE_LOW (0 << 2)
+#define CPM_HWCR_WLE_HIGH (1 << 2)
+#define CPM_HWCR_PIN_WAKEUP (1 << 1)
+#define CPM_HWCR_RTC_WAKEUP (1 << 0)
+
+/* Wakeup Status Register in Hibernate Mode */
+#define CPM_HWSR_WSR_PIN (1 << 1)
+#define CPM_HWSR_WSR_RTC (1 << 0)
+
+/* Reset Status Register */
+#define CPM_RSR_HR (1 << 2)
+#define CPM_RSR_WR (1 << 1)
+#define CPM_RSR_PR (1 << 0)
+
+/*
+ * TCU (Timer Counter Unit)
+ */
+#define TCU_TSR (TCU_BASE + 0x1C) /* Timer Stop Register */
+#define TCU_TSSR (TCU_BASE + 0x2C) /* Timer Stop Set Register */
+#define TCU_TSCR (TCU_BASE + 0x3C) /* Timer Stop Clear Register */
+#define TCU_TER (TCU_BASE + 0x10) /* Timer Counter Enable Register */
+#define TCU_TESR (TCU_BASE + 0x14) /* Timer Counter Enable Set Register */
+#define TCU_TECR (TCU_BASE + 0x18) /* Timer Counter Enable Clear Register */
+#define TCU_TFR (TCU_BASE + 0x20) /* Timer Flag Register */
+#define TCU_TFSR (TCU_BASE + 0x24) /* Timer Flag Set Register */
+#define TCU_TFCR (TCU_BASE + 0x28) /* Timer Flag Clear Register */
+#define TCU_TMR (TCU_BASE + 0x30) /* Timer Mask Register */
+#define TCU_TMSR (TCU_BASE + 0x34) /* Timer Mask Set Register */
+#define TCU_TMCR (TCU_BASE + 0x38) /* Timer Mask Clear Register */
+#define TCU_TDFR0 (TCU_BASE + 0x40) /* Timer Data Full Register */
+#define TCU_TDHR0 (TCU_BASE + 0x44) /* Timer Data Half Register */
+#define TCU_TCNT0 (TCU_BASE + 0x48) /* Timer Counter Register */
+#define TCU_TCSR0 (TCU_BASE + 0x4C) /* Timer Control Register */
+#define TCU_TDFR1 (TCU_BASE + 0x50)
+#define TCU_TDHR1 (TCU_BASE + 0x54)
+#define TCU_TCNT1 (TCU_BASE + 0x58)
+#define TCU_TCSR1 (TCU_BASE + 0x5C)
+#define TCU_TDFR2 (TCU_BASE + 0x60)
+#define TCU_TDHR2 (TCU_BASE + 0x64)
+#define TCU_TCNT2 (TCU_BASE + 0x68)
+#define TCU_TCSR2 (TCU_BASE + 0x6C)
+#define TCU_TDFR3 (TCU_BASE + 0x70)
+#define TCU_TDHR3 (TCU_BASE + 0x74)
+#define TCU_TCNT3 (TCU_BASE + 0x78)
+#define TCU_TCSR3 (TCU_BASE + 0x7C)
+#define TCU_TDFR4 (TCU_BASE + 0x80)
+#define TCU_TDHR4 (TCU_BASE + 0x84)
+#define TCU_TCNT4 (TCU_BASE + 0x88)
+#define TCU_TCSR4 (TCU_BASE + 0x8C)
+#define TCU_TDFR5 (TCU_BASE + 0x90)
+#define TCU_TDHR5 (TCU_BASE + 0x94)
+#define TCU_TCNT5 (TCU_BASE + 0x98)
+#define TCU_TCSR5 (TCU_BASE + 0x9C)
+
+/* n = 0,1,2,3,4,5 */
+#define TCU_TDFR(n) (TCU_BASE + (0x40 + (n)*0x10)) /* Timer Data Full Reg */
+#define TCU_TDHR(n) (TCU_BASE + (0x44 + (n)*0x10)) /* Timer Data Half Reg */
+#define TCU_TCNT(n) (TCU_BASE + (0x48 + (n)*0x10)) /* Timer Counter Reg */
+#define TCU_TCSR(n) (TCU_BASE + (0x4C + (n)*0x10)) /* Timer Control Reg */
+
+/* Register definitions */
+#define TCU_TCSR_PWM_SD (1 << 9)
+#define TCU_TCSR_PWM_INITL_HIGH (1 << 8)
+#define TCU_TCSR_PWM_EN (1 << 7)
+#define TCU_TCSR_PRESCALE_BIT 3
+#define TCU_TCSR_PRESCALE_MASK (0x7 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE1 (0x0 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE4 (0x1 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE16 (0x2 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE64 (0x3 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE256 (0x4 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_PRESCALE1024 (0x5 << TCU_TCSR_PRESCALE_BIT)
+#define TCU_TCSR_EXT_EN (1 << 2)
+#define TCU_TCSR_RTC_EN (1 << 1)
+#define TCU_TCSR_PCK_EN (1 << 0)
+
+#define TCU_TER_TCEN5 (1 << 5)
+#define TCU_TER_TCEN4 (1 << 4)
+#define TCU_TER_TCEN3 (1 << 3)
+#define TCU_TER_TCEN2 (1 << 2)
+#define TCU_TER_TCEN1 (1 << 1)
+#define TCU_TER_TCEN0 (1 << 0)
+
+#define TCU_TESR_TCST5 (1 << 5)
+#define TCU_TESR_TCST4 (1 << 4)
+#define TCU_TESR_TCST3 (1 << 3)
+#define TCU_TESR_TCST2 (1 << 2)
+#define TCU_TESR_TCST1 (1 << 1)
+#define TCU_TESR_TCST0 (1 << 0)
+
+#define TCU_TECR_TCCL5 (1 << 5)
+#define TCU_TECR_TCCL4 (1 << 4)
+#define TCU_TECR_TCCL3 (1 << 3)
+#define TCU_TECR_TCCL2 (1 << 2)
+#define TCU_TECR_TCCL1 (1 << 1)
+#define TCU_TECR_TCCL0 (1 << 0)
+
+#define TCU_TFR_HFLAG5 (1 << 21)
+#define TCU_TFR_HFLAG4 (1 << 20)
+#define TCU_TFR_HFLAG3 (1 << 19)
+#define TCU_TFR_HFLAG2 (1 << 18)
+#define TCU_TFR_HFLAG1 (1 << 17)
+#define TCU_TFR_HFLAG0 (1 << 16)
+#define TCU_TFR_FFLAG5 (1 << 5)
+#define TCU_TFR_FFLAG4 (1 << 4)
+#define TCU_TFR_FFLAG3 (1 << 3)
+#define TCU_TFR_FFLAG2 (1 << 2)
+#define TCU_TFR_FFLAG1 (1 << 1)
+#define TCU_TFR_FFLAG0 (1 << 0)
+
+#define TCU_TFSR_HFLAG5 (1 << 21)
+#define TCU_TFSR_HFLAG4 (1 << 20)
+#define TCU_TFSR_HFLAG3 (1 << 19)
+#define TCU_TFSR_HFLAG2 (1 << 18)
+#define TCU_TFSR_HFLAG1 (1 << 17)
+#define TCU_TFSR_HFLAG0 (1 << 16)
+#define TCU_TFSR_FFLAG5 (1 << 5)
+#define TCU_TFSR_FFLAG4 (1 << 4)
+#define TCU_TFSR_FFLAG3 (1 << 3)
+#define TCU_TFSR_FFLAG2 (1 << 2)
+#define TCU_TFSR_FFLAG1 (1 << 1)
+#define TCU_TFSR_FFLAG0 (1 << 0)
+
+#define TCU_TFCR_HFLAG5 (1 << 21)
+#define TCU_TFCR_HFLAG4 (1 << 20)
+#define TCU_TFCR_HFLAG3 (1 << 19)
+#define TCU_TFCR_HFLAG2 (1 << 18)
+#define TCU_TFCR_HFLAG1 (1 << 17)
+#define TCU_TFCR_HFLAG0 (1 << 16)
+#define TCU_TFCR_FFLAG5 (1 << 5)
+#define TCU_TFCR_FFLAG4 (1 << 4)
+#define TCU_TFCR_FFLAG3 (1 << 3)
+#define TCU_TFCR_FFLAG2 (1 << 2)
+#define TCU_TFCR_FFLAG1 (1 << 1)
+#define TCU_TFCR_FFLAG0 (1 << 0)
+
+#define TCU_TMR_HMASK5 (1 << 21)
+#define TCU_TMR_HMASK4 (1 << 20)
+#define TCU_TMR_HMASK3 (1 << 19)
+#define TCU_TMR_HMASK2 (1 << 18)
+#define TCU_TMR_HMASK1 (1 << 17)
+#define TCU_TMR_HMASK0 (1 << 16)
+#define TCU_TMR_FMASK5 (1 << 5)
+#define TCU_TMR_FMASK4 (1 << 4)
+#define TCU_TMR_FMASK3 (1 << 3)
+#define TCU_TMR_FMASK2 (1 << 2)
+#define TCU_TMR_FMASK1 (1 << 1)
+#define TCU_TMR_FMASK0 (1 << 0)
+
+#define TCU_TMSR_HMST5 (1 << 21)
+#define TCU_TMSR_HMST4 (1 << 20)
+#define TCU_TMSR_HMST3 (1 << 19)
+#define TCU_TMSR_HMST2 (1 << 18)
+#define TCU_TMSR_HMST1 (1 << 17)
+#define TCU_TMSR_HMST0 (1 << 16)
+#define TCU_TMSR_FMST5 (1 << 5)
+#define TCU_TMSR_FMST4 (1 << 4)
+#define TCU_TMSR_FMST3 (1 << 3)
+#define TCU_TMSR_FMST2 (1 << 2)
+#define TCU_TMSR_FMST1 (1 << 1)
+#define TCU_TMSR_FMST0 (1 << 0)
+
+#define TCU_TMCR_HMCL5 (1 << 21)
+#define TCU_TMCR_HMCL4 (1 << 20)
+#define TCU_TMCR_HMCL3 (1 << 19)
+#define TCU_TMCR_HMCL2 (1 << 18)
+#define TCU_TMCR_HMCL1 (1 << 17)
+#define TCU_TMCR_HMCL0 (1 << 16)
+#define TCU_TMCR_FMCL5 (1 << 5)
+#define TCU_TMCR_FMCL4 (1 << 4)
+#define TCU_TMCR_FMCL3 (1 << 3)
+#define TCU_TMCR_FMCL2 (1 << 2)
+#define TCU_TMCR_FMCL1 (1 << 1)
+#define TCU_TMCR_FMCL0 (1 << 0)
+
+#define TCU_TSR_WDTS (1 << 16)
+#define TCU_TSR_STOP5 (1 << 5)
+#define TCU_TSR_STOP4 (1 << 4)
+#define TCU_TSR_STOP3 (1 << 3)
+#define TCU_TSR_STOP2 (1 << 2)
+#define TCU_TSR_STOP1 (1 << 1)
+#define TCU_TSR_STOP0 (1 << 0)
+
+#define TCU_TSSR_WDTSS (1 << 16)
+#define TCU_TSSR_STPS5 (1 << 5)
+#define TCU_TSSR_STPS4 (1 << 4)
+#define TCU_TSSR_STPS3 (1 << 3)
+#define TCU_TSSR_STPS2 (1 << 2)
+#define TCU_TSSR_STPS1 (1 << 1)
+#define TCU_TSSR_STPS0 (1 << 0)
+
+#define TCU_TSSR_WDTSC (1 << 16)
+#define TCU_TSSR_STPC5 (1 << 5)
+#define TCU_TSSR_STPC4 (1 << 4)
+#define TCU_TSSR_STPC3 (1 << 3)
+#define TCU_TSSR_STPC2 (1 << 2)
+#define TCU_TSSR_STPC1 (1 << 1)
+#define TCU_TSSR_STPC0 (1 << 0)
+
+/*
+ * WDT (WatchDog Timer)
+ */
+#define WDT_TDR (WDT_BASE + 0x00)
+#define WDT_TCER (WDT_BASE + 0x04)
+#define WDT_TCNT (WDT_BASE + 0x08)
+#define WDT_TCSR (WDT_BASE + 0x0C)
+
+/* Register definition */
+#define WDT_TCSR_PRESCALE_BIT 3
+#define WDT_TCSR_PRESCALE_MASK (0x7 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE1 (0x0 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE4 (0x1 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE16 (0x2 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE64 (0x3 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE256 (0x4 << WDT_TCSR_PRESCALE_BIT)
+ #define WDT_TCSR_PRESCALE1024 (0x5 << WDT_TCSR_PRESCALE_BIT)
+#define WDT_TCSR_EXT_EN (1 << 2)
+#define WDT_TCSR_RTC_EN (1 << 1)
+#define WDT_TCSR_PCK_EN (1 << 0)
+
+#define WDT_TCER_TCEN (1 << 0)
+
+/*
+ * GPIO (General-Purpose I/O Ports)
+ */
+#define MAX_GPIO_NUM 128
+
+/* = 0,1,2,3 */
+#define GPIO_PXPIN(n) (GPIO_BASE + (0x00 + (n)*0x100)) /* PIN Level Register */
+#define GPIO_PXDAT(n) (GPIO_BASE + (0x10 + (n)*0x100)) /* Port Data Register */
+#define GPIO_PXDATS(n) (GPIO_BASE + (0x14 + (n)*0x100)) /* Port Data Set Register */
+#define GPIO_PXDATC(n) (GPIO_BASE + (0x18 + (n)*0x100)) /* Port Data Clear Register */
+#define GPIO_PXIM(n) (GPIO_BASE + (0x20 + (n)*0x100)) /* Interrupt Mask Register */
+#define GPIO_PXIMS(n) (GPIO_BASE + (0x24 + (n)*0x100)) /* Interrupt Mask Set Reg */
+#define GPIO_PXIMC(n) (GPIO_BASE + (0x28 + (n)*0x100)) /* Interrupt Mask Clear Reg */
+#define GPIO_PXPE(n) (GPIO_BASE + (0x30 + (n)*0x100)) /* Pull Enable Register */
+#define GPIO_PXPES(n) (GPIO_BASE + (0x34 + (n)*0x100)) /* Pull Enable Set Reg. */
+#define GPIO_PXPEC(n) (GPIO_BASE + (0x38 + (n)*0x100)) /* Pull Enable Clear Reg. */
+#define GPIO_PXFUN(n) (GPIO_BASE + (0x40 + (n)*0x100)) /* Function Register */
+#define GPIO_PXFUNS(n) (GPIO_BASE + (0x44 + (n)*0x100)) /* Function Set Register */
+#define GPIO_PXFUNC(n) (GPIO_BASE + (0x48 + (n)*0x100)) /* Function Clear Register */
+#define GPIO_PXSEL(n) (GPIO_BASE + (0x50 + (n)*0x100)) /* Select Register */
+#define GPIO_PXSELS(n) (GPIO_BASE + (0x54 + (n)*0x100)) /* Select Set Register */
+#define GPIO_PXSELC(n) (GPIO_BASE + (0x58 + (n)*0x100)) /* Select Clear Register */
+#define GPIO_PXDIR(n) (GPIO_BASE + (0x60 + (n)*0x100)) /* Direction Register */
+#define GPIO_PXDIRS(n) (GPIO_BASE + (0x64 + (n)*0x100)) /* Direction Set Register */
+#define GPIO_PXDIRC(n) (GPIO_BASE + (0x68 + (n)*0x100)) /* Direction Clear Register */
+#define GPIO_PXTRG(n) (GPIO_BASE + (0x70 + (n)*0x100)) /* Trigger Register */
+#define GPIO_PXTRGS(n) (GPIO_BASE + (0x74 + (n)*0x100)) /* Trigger Set Register */
+#define GPIO_PXTRGC(n) (GPIO_BASE + (0x78 + (n)*0x100)) /* Trigger Set Register */
+#define GPIO_PXFLG(n) (GPIO_BASE + (0x80 + (n)*0x100)) /* Port Flag Register */
+#define GPIO_PXFLGC(n) (GPIO_BASE + (0x14 + (n)*0x100)) /* Port Flag clear Register */
+
+/*
+ * UART
+ */
+#define IRDA_BASE UART0_BASE
+#define UART_BASE UART0_BASE
+#define UART_OFF 0x1000
+
+/* Register Offset */
+#define OFF_RDR (0x00) /* R 8b H'xx */
+#define OFF_TDR (0x00) /* W 8b H'xx */
+#define OFF_DLLR (0x00) /* RW 8b H'00 */
+#define OFF_DLHR (0x04) /* RW 8b H'00 */
+#define OFF_IER (0x04) /* RW 8b H'00 */
+#define OFF_ISR (0x08) /* R 8b H'01 */
+#define OFF_FCR (0x08) /* W 8b H'00 */
+#define OFF_LCR (0x0C) /* RW 8b H'00 */
+#define OFF_MCR (0x10) /* RW 8b H'00 */
+#define OFF_LSR (0x14) /* R 8b H'00 */
+#define OFF_MSR (0x18) /* R 8b H'00 */
+#define OFF_SPR (0x1C) /* RW 8b H'00 */
+#define OFF_SIRCR (0x20) /* RW 8b H'00, UART0 */
+#define OFF_UMR (0x24) /* RW 8b H'00, UART M Register */
+#define OFF_UACR (0x28) /* RW 8b H'00, UART Add Cycle Register */
+
+/* Register Address */
+#define UART0_RDR (UART0_BASE + OFF_RDR)
+#define UART0_TDR (UART0_BASE + OFF_TDR)
+#define UART0_DLLR (UART0_BASE + OFF_DLLR)
+#define UART0_DLHR (UART0_BASE + OFF_DLHR)
+#define UART0_IER (UART0_BASE + OFF_IER)
+#define UART0_ISR (UART0_BASE + OFF_ISR)
+#define UART0_FCR (UART0_BASE + OFF_FCR)
+#define UART0_LCR (UART0_BASE + OFF_LCR)
+#define UART0_MCR (UART0_BASE + OFF_MCR)
+#define UART0_LSR (UART0_BASE + OFF_LSR)
+#define UART0_MSR (UART0_BASE + OFF_MSR)
+#define UART0_SPR (UART0_BASE + OFF_SPR)
+#define UART0_SIRCR (UART0_BASE + OFF_SIRCR)
+#define UART0_UMR (UART0_BASE + OFF_UMR)
+#define UART0_UACR (UART0_BASE + OFF_UACR)
+
+/*
+ * Define macros for UART_IER
+ * UART Interrupt Enable Register
+ */
+#define UART_IER_RIE (1 << 0) /* 0: receive fifo "full" interrupt disable */
+#define UART_IER_TIE (1 << 1) /* 0: transmit fifo "empty" interrupt disable */
+#define UART_IER_RLIE (1 << 2) /* 0: receive line status interrupt disable */
+#define UART_IER_MIE (1 << 3) /* 0: modem status interrupt disable */
+#define UART_IER_RTIE (1 << 4) /* 0: receive timeout interrupt disable */
+
+/*
+ * Define macros for UART_ISR
+ * UART Interrupt Status Register
+ */
+#define UART_ISR_IP (1 << 0) /* 0: interrupt is pending 1: no interrupt */
+#define UART_ISR_IID (7 << 1) /* Source of Interrupt */
+#define UART_ISR_IID_MSI (0 << 1) /* Modem status interrupt */
+#define UART_ISR_IID_THRI (1 << 1) /* Transmitter holding register empty */
+#define UART_ISR_IID_RDI (2 << 1) /* Receiver data interrupt */
+#define UART_ISR_IID_RLSI (3 << 1) /* Receiver line status interrupt */
+#define UART_ISR_FFMS (3 << 6) /* FIFO mode select, set when UART_FCR.FE is set to 1 */
+#define UART_ISR_FFMS_NO_FIFO (0 << 6)
+#define UART_ISR_FFMS_FIFO_MODE (3 << 6)
+
+/*
+ * Define macros for UART_FCR
+ * UART FIFO Control Register
+ */
+#define UART_FCR_FE (1 << 0) /* 0: non-FIFO mode 1: FIFO mode */
+#define UART_FCR_RFLS (1 << 1) /* write 1 to flush receive FIFO */
+#define UART_FCR_TFLS (1 << 2) /* write 1 to flush transmit FIFO */
+#define UART_FCR_DMS (1 << 3) /* 0: disable DMA mode */
+#define UART_FCR_UUE (1 << 4) /* 0: disable UART */
+#define UART_FCR_RTRG (3 << 6) /* Receive FIFO Data Trigger */
+#define UART_FCR_RTRG_1 (0 << 6)
+#define UART_FCR_RTRG_4 (1 << 6)
+#define UART_FCR_RTRG_8 (2 << 6)
+#define UART_FCR_RTRG_15 (3 << 6)
+
+/*
+ * Define macros for UART_LCR
+ * UART Line Control Register
+ */
+#define UART_LCR_WLEN (3 << 0) /* word length */
+#define UART_LCR_WLEN_5 (0 << 0)
+#define UART_LCR_WLEN_6 (1 << 0)
+#define UART_LCR_WLEN_7 (2 << 0)
+#define UART_LCR_WLEN_8 (3 << 0)
+#define UART_LCR_STOP (1 << 2) /* 0: 1 stop bit when word length is 5,6,7,8
+ 1: 1.5 stop bits when 5; 2 stop bits when 6,7,8 */
+#define UART_LCR_STOP_1 (0 << 2) /* 0: 1 stop bit when word length is 5,6,7,8
+ 1: 1.5 stop bits when 5; 2 stop bits when 6,7,8 */
+#define UART_LCR_STOP_2 (1 << 2) /* 0: 1 stop bit when word length is 5,6,7,8
+ 1: 1.5 stop bits when 5; 2 stop bits when 6,7,8 */
+
+#define UART_LCR_PE (1 << 3) /* 0: parity disable */
+#define UART_LCR_PROE (1 << 4) /* 0: even parity 1: odd parity */
+#define UART_LCR_SPAR (1 << 5) /* 0: sticky parity disable */
+#define UART_LCR_SBRK (1 << 6) /* write 0 normal, write 1 send break */
+#define UART_LCR_DLAB (1 << 7) /* 0: access UART_RDR/TDR/IER 1: access UART_DLLR/DLHR */
+
+/*
+ * Define macros for UART_LSR
+ * UART Line Status Register
+ */
+#define UART_LSR_DR (1 << 0) /* 0: receive FIFO is empty 1: receive data is ready */
+#define UART_LSR_ORER (1 << 1) /* 0: no overrun error */
+#define UART_LSR_PER (1 << 2) /* 0: no parity error */
+#define UART_LSR_FER (1 << 3) /* 0; no framing error */
+#define UART_LSR_BRK (1 << 4) /* 0: no break detected 1: receive a break signal */
+#define UART_LSR_TDRQ (1 << 5) /* 1: transmit FIFO half "empty" */
+#define UART_LSR_TEMT (1 << 6) /* 1: transmit FIFO and shift registers empty */
+#define UART_LSR_RFER (1 << 7) /* 0: no receive error 1: receive error in FIFO mode */
+
+/*
+ * Define macros for UART_MCR
+ * UART Modem Control Register
+ */
+#define UART_MCR_DTR (1 << 0) /* 0: DTR_ ouput high */
+#define UART_MCR_RTS (1 << 1) /* 0: RTS_ output high */
+#define UART_MCR_OUT1 (1 << 2) /* 0: UART_MSR.RI is set to 0 and RI_ input high */
+#define UART_MCR_OUT2 (1 << 3) /* 0: UART_MSR.DCD is set to 0 and DCD_ input high */
+#define UART_MCR_LOOP (1 << 4) /* 0: normal 1: loopback mode */
+#define UART_MCR_MCE (1 << 7) /* 0: modem function is disable */
+
+/*
+ * Define macros for UART_MSR
+ * UART Modem Status Register
+ */
+#define UART_MSR_DCTS (1 << 0) /* 0: no change on CTS_ pin since last read of UART_MSR */
+#define UART_MSR_DDSR (1 << 1) /* 0: no change on DSR_ pin since last read of UART_MSR */
+#define UART_MSR_DRI (1 << 2) /* 0: no change on RI_ pin since last read of UART_MSR */
+#define UART_MSR_DDCD (1 << 3) /* 0: no change on DCD_ pin since last read of UART_MSR */
+#define UART_MSR_CTS (1 << 4) /* 0: CTS_ pin is high */
+#define UART_MSR_DSR (1 << 5) /* 0: DSR_ pin is high */
+#define UART_MSR_RI (1 << 6) /* 0: RI_ pin is high */
+#define UART_MSR_DCD (1 << 7) /* 0: DCD_ pin is high */
+
+/*
+ * Define macros for SIRCR
+ * Slow IrDA Control Register
+ */
+#define SIRCR_TSIRE (1 << 0) /* 0: transmitter is in UART mode 1: IrDA mode */
+#define SIRCR_RSIRE (1 << 1) /* 0: receiver is in UART mode 1: IrDA mode */
+#define SIRCR_TPWS (1 << 2) /* 0: transmit 0 pulse width is 3/16 of bit length
+ 1: 0 pulse width is 1.6us for 115.2Kbps */
+#define SIRCR_TXPL (1 << 3) /* 0: encoder generates a positive pulse for 0 */
+#define SIRCR_RXPL (1 << 4) /* 0: decoder interprets positive pulse as 0 */
+
+/*
+ * MSC
+ */
+#define MSC_STRPCL (MSC_BASE + 0x000)
+#define MSC_STAT (MSC_BASE + 0x004)
+#define MSC_CLKRT (MSC_BASE + 0x008)
+#define MSC_CMDAT (MSC_BASE + 0x00C)
+#define MSC_RESTO (MSC_BASE + 0x010)
+#define MSC_RDTO (MSC_BASE + 0x014)
+#define MSC_BLKLEN (MSC_BASE + 0x018)
+#define MSC_NOB (MSC_BASE + 0x01C)
+#define MSC_SNOB (MSC_BASE + 0x020)
+#define MSC_IMASK (MSC_BASE + 0x024)
+#define MSC_CMD (MSC_BASE + 0x02C)
+#define MSC_ARG (MSC_BASE + 0x030)
+#define MSC_RES (MSC_BASE + 0x034)
+#define MSC_RXFIFO (MSC_BASE + 0x038)
+#define MSC_TXFIFO (MSC_BASE + 0x03C)
+
+/* MSC Clock and Control Register (MSC_STRPCL) */
+#define MSC_STRPCL_EXIT_MULTIPLE (1 << 7)
+#define MSC_STRPCL_EXIT_TRANSFER (1 << 6)
+#define MSC_STRPCL_START_READWAIT (1 << 5)
+#define MSC_STRPCL_STOP_READWAIT (1 << 4)
+#define MSC_STRPCL_RESET (1 << 3)
+#define MSC_STRPCL_START_OP (1 << 2)
+#define MSC_STRPCL_CLOCK_CONTROL_BIT 0
+#define MSC_STRPCL_CLOCK_CONTROL_MASK (0x3 << MSC_STRPCL_CLOCK_CONTROL_BIT)
+ #define MSC_STRPCL_CLOCK_CONTROL_STOP (0x1 << MSC_STRPCL_CLOCK_CONTROL_BIT) /* Stop MMC/SD clock */
+ #define MSC_STRPCL_CLOCK_CONTROL_START (0x2 << MSC_STRPCL_CLOCK_CONTROL_BIT) /* Start MMC/SD clock */
+
+/* MSC Status Register (MSC_STAT) */
+#define MSC_STAT_IS_RESETTING (1 << 15)
+#define MSC_STAT_SDIO_INT_ACTIVE (1 << 14)
+#define MSC_STAT_PRG_DONE (1 << 13)
+#define MSC_STAT_DATA_TRAN_DONE (1 << 12)
+#define MSC_STAT_END_CMD_RES (1 << 11)
+#define MSC_STAT_DATA_FIFO_AFULL (1 << 10)
+#define MSC_STAT_IS_READWAIT (1 << 9)
+#define MSC_STAT_CLK_EN (1 << 8)
+#define MSC_STAT_DATA_FIFO_FULL (1 << 7)
+#define MSC_STAT_DATA_FIFO_EMPTY (1 << 6)
+#define MSC_STAT_CRC_RES_ERR (1 << 5)
+#define MSC_STAT_CRC_READ_ERROR (1 << 4)
+#define MSC_STAT_CRC_WRITE_ERROR_BIT 2
+#define MSC_STAT_CRC_WRITE_ERROR_MASK (0x3 << MSC_STAT_CRC_WRITE_ERROR_BIT)
+ #define MSC_STAT_CRC_WRITE_ERROR_NO (0 << MSC_STAT_CRC_WRITE_ERROR_BIT) /* No error on transmission of data */
+ #define MSC_STAT_CRC_WRITE_ERROR (1 << MSC_STAT_CRC_WRITE_ERROR_BIT) /* Card observed erroneous transmission of data */
+ #define MSC_STAT_CRC_WRITE_ERROR_NOSTS (2 << MSC_STAT_CRC_WRITE_ERROR_BIT) /* No CRC status is sent back */
+#define MSC_STAT_TIME_OUT_RES (1 << 1)
+#define MSC_STAT_TIME_OUT_READ (1 << 0)
+
+/* MSC Bus Clock Control Register (MSC_CLKRT) */
+
+#define MSC_CLKRT_CLK_RATE_BIT 0
+#define MSC_CLKRT_CLK_RATE_MASK (0x7 << MSC_CLKRT_CLK_RATE_BIT)
+ #define MSC_CLKRT_CLK_RATE_DIV_1 (0x0 << MSC_CLKRT_CLK_RATE_BIT) /* CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_2 (0x1 << MSC_CLKRT_CLK_RATE_BIT) /* 1/2 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_4 (0x2 << MSC_CLKRT_CLK_RATE_BIT) /* 1/4 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_8 (0x3 << MSC_CLKRT_CLK_RATE_BIT) /* 1/8 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_16 (0x4 << MSC_CLKRT_CLK_RATE_BIT) /* 1/16 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_32 (0x5 << MSC_CLKRT_CLK_RATE_BIT) /* 1/32 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_64 (0x6 << MSC_CLKRT_CLK_RATE_BIT) /* 1/64 of CLK_SRC */
+ #define MSC_CLKRT_CLK_RATE_DIV_128 (0x7 << MSC_CLKRT_CLK_RATE_BIT) /* 1/128 of CLK_SRC */
+
+/* MSC Command Sequence Control Register (MSC_CMDAT) */
+#define MSC_CMDAT_IO_ABORT (1 << 11)
+#define MSC_CMDAT_BUS_WIDTH_BIT 9
+#define MSC_CMDAT_BUS_WIDTH_MASK (0x3 << MSC_CMDAT_BUS_WIDTH_BIT)
+#define MSC_CMDAT_BUS_WIDTH_1BIT (0x0 << MSC_CMDAT_BUS_WIDTH_BIT)
+#define MSC_CMDAT_BUS_WIDTH_4BIT (0x2 << MSC_CMDAT_BUS_WIDTH_BIT)
+#define MSC_CMDAT_DMA_EN (1 << 8)
+#define MSC_CMDAT_INIT (1 << 7)
+#define MSC_CMDAT_BUSY (1 << 6)
+#define MSC_CMDAT_STREAM_BLOCK (1 << 5)
+#define MSC_CMDAT_WRITE (1 << 4)
+#define MSC_CMDAT_READ (0 << 4)
+#define MSC_CMDAT_DATA_EN (1 << 3)
+#define MSC_CMDAT_RESPONSE_BIT 0
+#define MSC_CMDAT_RESPONSE_MASK (0x7 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_NONE (0x0 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R1 (0x1 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R2 (0x2 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R3 (0x3 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R4 (0x4 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R5 (0x5 << MSC_CMDAT_RESPONSE_BIT)
+#define MSC_CMDAT_RESPONSE_R6 (0x6 << MSC_CMDAT_RESPONSE_BIT)
+
+/* MSC Interrupts Mask Register (MSC_IMASK) */
+#define MSC_IMASK_SDIO (1 << 7)
+#define MSC_IMASK_TXFIFO_WR_REQ (1 << 6)
+#define MSC_IMASK_RXFIFO_RD_REQ (1 << 5)
+#define MSC_IMASK_END_CMD_RES (1 << 2)
+#define MSC_IMASK_PRG_DONE (1 << 1)
+#define MSC_IMASK_DATA_TRAN_DONE (1 << 0)
+
+/*
+ * EMC (External Memory Controller)
+ */
+#define EMC_BCR (EMC_BASE + 0x0) /* BCR */
+
+#define EMC_SMCR0 (EMC_BASE + 0x10) /* Static Memory Control Register 0 */
+#define EMC_SMCR1 (EMC_BASE + 0x14) /* Static Memory Control Register 1 */
+#define EMC_SMCR2 (EMC_BASE + 0x18) /* Static Memory Control Register 2 */
+#define EMC_SMCR3 (EMC_BASE + 0x1c) /* Static Memory Control Register 3 */
+#define EMC_SMCR4 (EMC_BASE + 0x20) /* Static Memory Control Register 4 */
+#define EMC_SACR0 (EMC_BASE + 0x30) /* Static Memory Bank 0 Addr Config Reg */
+#define EMC_SACR1 (EMC_BASE + 0x34) /* Static Memory Bank 1 Addr Config Reg */
+#define EMC_SACR2 (EMC_BASE + 0x38) /* Static Memory Bank 2 Addr Config Reg */
+#define EMC_SACR3 (EMC_BASE + 0x3c) /* Static Memory Bank 3 Addr Config Reg */
+#define EMC_SACR4 (EMC_BASE + 0x40) /* Static Memory Bank 4 Addr Config Reg */
+
+#define EMC_NFCSR (EMC_BASE + 0x050) /* NAND Flash Control/Status Register */
+#define EMC_NFECR (EMC_BASE + 0x100) /* NAND Flash ECC Control Register */
+#define EMC_NFECC (EMC_BASE + 0x104) /* NAND Flash ECC Data Register */
+#define EMC_NFPAR0 (EMC_BASE + 0x108) /* NAND Flash RS Parity 0 Register */
+#define EMC_NFPAR1 (EMC_BASE + 0x10c) /* NAND Flash RS Parity 1 Register */
+#define EMC_NFPAR2 (EMC_BASE + 0x110) /* NAND Flash RS Parity 2 Register */
+#define EMC_NFINTS (EMC_BASE + 0x114) /* NAND Flash Interrupt Status Register */
+#define EMC_NFINTE (EMC_BASE + 0x118) /* NAND Flash Interrupt Enable Register */
+#define EMC_NFERR0 (EMC_BASE + 0x11c) /* NAND Flash RS Error Report 0 Register */
+#define EMC_NFERR1 (EMC_BASE + 0x120) /* NAND Flash RS Error Report 1 Register */
+#define EMC_NFERR2 (EMC_BASE + 0x124) /* NAND Flash RS Error Report 2 Register */
+#define EMC_NFERR3 (EMC_BASE + 0x128) /* NAND Flash RS Error Report 3 Register */
+
+#define EMC_DMCR (EMC_BASE + 0x80) /* DRAM Control Register */
+#define EMC_RTCSR (EMC_BASE + 0x84) /* Refresh Time Control/Status Register */
+#define EMC_RTCNT (EMC_BASE + 0x88) /* Refresh Timer Counter */
+#define EMC_RTCOR (EMC_BASE + 0x8c) /* Refresh Time Constant Register */
+#define EMC_DMAR0 (EMC_BASE + 0x90) /* SDRAM Bank 0 Addr Config Register */
+#define EMC_SDMR0 (EMC_BASE + 0xa000) /* Mode Register of SDRAM bank 0 */
+
+/* Static Memory Control Register */
+#define EMC_SMCR_STRV_BIT 24
+#define EMC_SMCR_STRV_MASK (0x0f << EMC_SMCR_STRV_BIT)
+#define EMC_SMCR_TAW_BIT 20
+#define EMC_SMCR_TAW_MASK (0x0f << EMC_SMCR_TAW_BIT)
+#define EMC_SMCR_TBP_BIT 16
+#define EMC_SMCR_TBP_MASK (0x0f << EMC_SMCR_TBP_BIT)
+#define EMC_SMCR_TAH_BIT 12
+#define EMC_SMCR_TAH_MASK (0x07 << EMC_SMCR_TAH_BIT)
+#define EMC_SMCR_TAS_BIT 8
+#define EMC_SMCR_TAS_MASK (0x07 << EMC_SMCR_TAS_BIT)
+#define EMC_SMCR_BW_BIT 6
+#define EMC_SMCR_BW_MASK (0x03 << EMC_SMCR_BW_BIT)
+ #define EMC_SMCR_BW_8BIT (0 << EMC_SMCR_BW_BIT)
+ #define EMC_SMCR_BW_16BIT (1 << EMC_SMCR_BW_BIT)
+ #define EMC_SMCR_BW_32BIT (2 << EMC_SMCR_BW_BIT)
+#define EMC_SMCR_BCM (1 << 3)
+#define EMC_SMCR_BL_BIT 1
+#define EMC_SMCR_BL_MASK (0x03 << EMC_SMCR_BL_BIT)
+ #define EMC_SMCR_BL_4 (0 << EMC_SMCR_BL_BIT)
+ #define EMC_SMCR_BL_8 (1 << EMC_SMCR_BL_BIT)
+ #define EMC_SMCR_BL_16 (2 << EMC_SMCR_BL_BIT)
+ #define EMC_SMCR_BL_32 (3 << EMC_SMCR_BL_BIT)
+#define EMC_SMCR_SMT (1 << 0)
+
+/* Static Memory Bank Addr Config Reg */
+#define EMC_SACR_BASE_BIT 8
+#define EMC_SACR_BASE_MASK (0xff << EMC_SACR_BASE_BIT)
+#define EMC_SACR_MASK_BIT 0
+#define EMC_SACR_MASK_MASK (0xff << EMC_SACR_MASK_BIT)
+
+/* NAND Flash Control/Status Register */
+#define EMC_NFCSR_NFCE4 (1 << 7) /* NAND Flash Enable */
+#define EMC_NFCSR_NFE4 (1 << 6) /* NAND Flash FCE# Assertion Enable */
+#define EMC_NFCSR_NFCE3 (1 << 5)
+#define EMC_NFCSR_NFE3 (1 << 4)
+#define EMC_NFCSR_NFCE2 (1 << 3)
+#define EMC_NFCSR_NFE2 (1 << 2)
+#define EMC_NFCSR_NFCE1 (1 << 1)
+#define EMC_NFCSR_NFE1 (1 << 0)
+
+/* NAND Flash ECC Control Register */
+#define EMC_NFECR_PRDY (1 << 4) /* Parity Ready */
+#define EMC_NFECR_RS_DECODING (0 << 3) /* RS is in decoding phase */
+#define EMC_NFECR_RS_ENCODING (1 << 3) /* RS is in encoding phase */
+#define EMC_NFECR_HAMMING (0 << 2) /* Select HAMMING Correction Algorithm */
+#define EMC_NFECR_RS (1 << 2) /* Select RS Correction Algorithm */
+#define EMC_NFECR_ERST (1 << 1) /* ECC Reset */
+#define EMC_NFECR_ECCE (1 << 0) /* ECC Enable */
+
+/* NAND Flash ECC Data Register */
+#define EMC_NFECC_ECC2_BIT 16
+#define EMC_NFECC_ECC2_MASK (0xff << EMC_NFECC_ECC2_BIT)
+#define EMC_NFECC_ECC1_BIT 8
+#define EMC_NFECC_ECC1_MASK (0xff << EMC_NFECC_ECC1_BIT)
+#define EMC_NFECC_ECC0_BIT 0
+#define EMC_NFECC_ECC0_MASK (0xff << EMC_NFECC_ECC0_BIT)
+
+/* NAND Flash Interrupt Status Register */
+#define EMC_NFINTS_ERRCNT_BIT 29 /* Error Count */
+#define EMC_NFINTS_ERRCNT_MASK (0x7 << EMC_NFINTS_ERRCNT_BIT)
+#define EMC_NFINTS_PADF (1 << 4) /* Padding Finished */
+#define EMC_NFINTS_DECF (1 << 3) /* Decoding Finished */
+#define EMC_NFINTS_ENCF (1 << 2) /* Encoding Finished */
+#define EMC_NFINTS_UNCOR (1 << 1) /* Uncorrectable Error Occurred */
+#define EMC_NFINTS_ERR (1 << 0) /* Error Occurred */
+
+/* NAND Flash Interrupt Enable Register */
+#define EMC_NFINTE_PADFE (1 << 4) /* Padding Finished Interrupt Enable */
+#define EMC_NFINTE_DECFE (1 << 3) /* Decoding Finished Interrupt Enable */
+#define EMC_NFINTE_ENCFE (1 << 2) /* Encoding Finished Interrupt Enable */
+#define EMC_NFINTE_UNCORE (1 << 1) /* Uncorrectable Error Occurred Intr Enable */
+#define EMC_NFINTE_ERRE (1 << 0) /* Error Occurred Interrupt */
+
+/* NAND Flash RS Error Report Register */
+#define EMC_NFERR_INDEX_BIT 16 /* Error Symbol Index */
+#define EMC_NFERR_INDEX_MASK (0x1ff << EMC_NFERR_INDEX_BIT)
+#define EMC_NFERR_MASK_BIT 0 /* Error Symbol Value */
+#define EMC_NFERR_MASK_MASK (0x1ff << EMC_NFERR_MASK_BIT)
+
+/* DRAM Control Register */
+#define EMC_DMCR_BW_BIT 31
+#define EMC_DMCR_BW (1 << EMC_DMCR_BW_BIT)
+#define EMC_DMCR_CA_BIT 26
+#define EMC_DMCR_CA_MASK (0x07 << EMC_DMCR_CA_BIT)
+ #define EMC_DMCR_CA_8 (0 << EMC_DMCR_CA_BIT)
+ #define EMC_DMCR_CA_9 (1 << EMC_DMCR_CA_BIT)
+ #define EMC_DMCR_CA_10 (2 << EMC_DMCR_CA_BIT)
+ #define EMC_DMCR_CA_11 (3 << EMC_DMCR_CA_BIT)
+ #define EMC_DMCR_CA_12 (4 << EMC_DMCR_CA_BIT)
+#define EMC_DMCR_RMODE (1 << 25)
+#define EMC_DMCR_RFSH (1 << 24)
+#define EMC_DMCR_MRSET (1 << 23)
+#define EMC_DMCR_RA_BIT 20
+#define EMC_DMCR_RA_MASK (0x03 << EMC_DMCR_RA_BIT)
+ #define EMC_DMCR_RA_11 (0 << EMC_DMCR_RA_BIT)
+ #define EMC_DMCR_RA_12 (1 << EMC_DMCR_RA_BIT)
+ #define EMC_DMCR_RA_13 (2 << EMC_DMCR_RA_BIT)
+#define EMC_DMCR_BA_BIT 19
+#define EMC_DMCR_BA (1 << EMC_DMCR_BA_BIT)
+#define EMC_DMCR_PDM (1 << 18)
+#define EMC_DMCR_EPIN (1 << 17)
+#define EMC_DMCR_TRAS_BIT 13
+#define EMC_DMCR_TRAS_MASK (0x07 << EMC_DMCR_TRAS_BIT)
+#define EMC_DMCR_RCD_BIT 11
+#define EMC_DMCR_RCD_MASK (0x03 << EMC_DMCR_RCD_BIT)
+#define EMC_DMCR_TPC_BIT 8
+#define EMC_DMCR_TPC_MASK (0x07 << EMC_DMCR_TPC_BIT)
+#define EMC_DMCR_TRWL_BIT 5
+#define EMC_DMCR_TRWL_MASK (0x03 << EMC_DMCR_TRWL_BIT)
+#define EMC_DMCR_TRC_BIT 2
+#define EMC_DMCR_TRC_MASK (0x07 << EMC_DMCR_TRC_BIT)
+#define EMC_DMCR_TCL_BIT 0
+#define EMC_DMCR_TCL_MASK (0x03 << EMC_DMCR_TCL_BIT)
+
+/* Refresh Time Control/Status Register */
+#define EMC_RTCSR_CMF (1 << 7)
+#define EMC_RTCSR_CKS_BIT 0
+#define EMC_RTCSR_CKS_MASK (0x07 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_DISABLE (0 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_4 (1 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_16 (2 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_64 (3 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_256 (4 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_1024 (5 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_2048 (6 << EMC_RTCSR_CKS_BIT)
+ #define EMC_RTCSR_CKS_4096 (7 << EMC_RTCSR_CKS_BIT)
+
+/* SDRAM Bank Address Configuration Register */
+#define EMC_DMAR_BASE_BIT 8
+#define EMC_DMAR_BASE_MASK (0xff << EMC_DMAR_BASE_BIT)
+#define EMC_DMAR_MASK_BIT 0
+#define EMC_DMAR_MASK_MASK (0xff << EMC_DMAR_MASK_BIT)
+
+/* Mode Register of SDRAM bank 0 */
+#define EMC_SDMR_BM (1 << 9) /* Write Burst Mode */
+#define EMC_SDMR_OM_BIT 7 /* Operating Mode */
+#define EMC_SDMR_OM_MASK (3 << EMC_SDMR_OM_BIT)
+ #define EMC_SDMR_OM_NORMAL (0 << EMC_SDMR_OM_BIT)
+#define EMC_SDMR_CAS_BIT 4 /* CAS Latency */
+#define EMC_SDMR_CAS_MASK (7 << EMC_SDMR_CAS_BIT)
+ #define EMC_SDMR_CAS_1 (1 << EMC_SDMR_CAS_BIT)
+ #define EMC_SDMR_CAS_2 (2 << EMC_SDMR_CAS_BIT)
+ #define EMC_SDMR_CAS_3 (3 << EMC_SDMR_CAS_BIT)
+#define EMC_SDMR_BT_BIT 3 /* Burst Type */
+#define EMC_SDMR_BT_MASK (1 << EMC_SDMR_BT_BIT)
+ #define EMC_SDMR_BT_SEQ (0 << EMC_SDMR_BT_BIT) /* Sequential */
+ #define EMC_SDMR_BT_INT (1 << EMC_SDMR_BT_BIT) /* Interleave */
+#define EMC_SDMR_BL_BIT 0 /* Burst Length */
+#define EMC_SDMR_BL_MASK (7 << EMC_SDMR_BL_BIT)
+ #define EMC_SDMR_BL_1 (0 << EMC_SDMR_BL_BIT)
+ #define EMC_SDMR_BL_2 (1 << EMC_SDMR_BL_BIT)
+ #define EMC_SDMR_BL_4 (2 << EMC_SDMR_BL_BIT)
+ #define EMC_SDMR_BL_8 (3 << EMC_SDMR_BL_BIT)
+
+#define EMC_SDMR_CAS2_16BIT \
+ (EMC_SDMR_CAS_2 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_2)
+#define EMC_SDMR_CAS2_32BIT \
+ (EMC_SDMR_CAS_2 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_4)
+#define EMC_SDMR_CAS3_16BIT \
+ (EMC_SDMR_CAS_3 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_2)
+#define EMC_SDMR_CAS3_32BIT \
+ (EMC_SDMR_CAS_3 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_4)
+
+/*
+ * CIM
+ */
+#define CIM_CFG (CIM_BASE + 0x0000)
+#define CIM_CTRL (CIM_BASE + 0x0004)
+#define CIM_STATE (CIM_BASE + 0x0008)
+#define CIM_IID (CIM_BASE + 0x000C)
+#define CIM_RXFIFO (CIM_BASE + 0x0010)
+#define CIM_DA (CIM_BASE + 0x0020)
+#define CIM_FA (CIM_BASE + 0x0024)
+#define CIM_FID (CIM_BASE + 0x0028)
+#define CIM_CMD (CIM_BASE + 0x002C)
+
+
+/* CIM Configuration Register (CIM_CFG) */
+#define CIM_CFG_INV_DAT (1 << 15)
+#define CIM_CFG_VSP (1 << 14)
+#define CIM_CFG_HSP (1 << 13)
+#define CIM_CFG_PCP (1 << 12)
+#define CIM_CFG_DUMMY_ZERO (1 << 9)
+#define CIM_CFG_EXT_VSYNC (1 << 8)
+#define CIM_CFG_PACK_BIT 4
+#define CIM_CFG_PACK_MASK (0x7 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_0 (0 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_1 (1 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_2 (2 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_3 (3 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_4 (4 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_5 (5 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_6 (6 << CIM_CFG_PACK_BIT)
+ #define CIM_CFG_PACK_7 (7 << CIM_CFG_PACK_BIT)
+#define CIM_CFG_DSM_BIT 0
+#define CIM_CFG_DSM_MASK (0x3 << CIM_CFG_DSM_BIT)
+ #define CIM_CFG_DSM_CPM (0 << CIM_CFG_DSM_BIT) /* CCIR656 Progressive Mode */
+ #define CIM_CFG_DSM_CIM (1 << CIM_CFG_DSM_BIT) /* CCIR656 Interlace Mode */
+ #define CIM_CFG_DSM_GCM (2 << CIM_CFG_DSM_BIT) /* Gated Clock Mode */
+ #define CIM_CFG_DSM_NGCM (3 << CIM_CFG_DSM_BIT) /* Non-Gated Clock Mode */
+
+/* CIM Control Register (CIM_CTRL) */
+#define CIM_CTRL_MCLKDIV_BIT 24
+#define CIM_CTRL_MCLKDIV_MASK (0xff << CIM_CTRL_MCLKDIV_BIT)
+#define CIM_CTRL_FRC_BIT 16
+#define CIM_CTRL_FRC_MASK (0xf << CIM_CTRL_FRC_BIT)
+ #define CIM_CTRL_FRC_1 (0x0 << CIM_CTRL_FRC_BIT) /* Sample every frame */
+ #define CIM_CTRL_FRC_2 (0x1 << CIM_CTRL_FRC_BIT) /* Sample 1/2 frame */
+ #define CIM_CTRL_FRC_3 (0x2 << CIM_CTRL_FRC_BIT) /* Sample 1/3 frame */
+ #define CIM_CTRL_FRC_4 (0x3 << CIM_CTRL_FRC_BIT) /* Sample 1/4 frame */
+ #define CIM_CTRL_FRC_5 (0x4 << CIM_CTRL_FRC_BIT) /* Sample 1/5 frame */
+ #define CIM_CTRL_FRC_6 (0x5 << CIM_CTRL_FRC_BIT) /* Sample 1/6 frame */
+ #define CIM_CTRL_FRC_7 (0x6 << CIM_CTRL_FRC_BIT) /* Sample 1/7 frame */
+ #define CIM_CTRL_FRC_8 (0x7 << CIM_CTRL_FRC_BIT) /* Sample 1/8 frame */
+ #define CIM_CTRL_FRC_9 (0x8 << CIM_CTRL_FRC_BIT) /* Sample 1/9 frame */
+ #define CIM_CTRL_FRC_10 (0x9 << CIM_CTRL_FRC_BIT) /* Sample 1/10 frame */
+ #define CIM_CTRL_FRC_11 (0xA << CIM_CTRL_FRC_BIT) /* Sample 1/11 frame */
+ #define CIM_CTRL_FRC_12 (0xB << CIM_CTRL_FRC_BIT) /* Sample 1/12 frame */
+ #define CIM_CTRL_FRC_13 (0xC << CIM_CTRL_FRC_BIT) /* Sample 1/13 frame */
+ #define CIM_CTRL_FRC_14 (0xD << CIM_CTRL_FRC_BIT) /* Sample 1/14 frame */
+ #define CIM_CTRL_FRC_15 (0xE << CIM_CTRL_FRC_BIT) /* Sample 1/15 frame */
+ #define CIM_CTRL_FRC_16 (0xF << CIM_CTRL_FRC_BIT) /* Sample 1/16 frame */
+#define CIM_CTRL_VDDM (1 << 13)
+#define CIM_CTRL_DMA_SOFM (1 << 12)
+#define CIM_CTRL_DMA_EOFM (1 << 11)
+#define CIM_CTRL_DMA_STOPM (1 << 10)
+#define CIM_CTRL_RXF_TRIGM (1 << 9)
+#define CIM_CTRL_RXF_OFM (1 << 8)
+#define CIM_CTRL_RXF_TRIG_BIT 4
+#define CIM_CTRL_RXF_TRIG_MASK (0x7 << CIM_CTRL_RXF_TRIG_BIT)
+ #define CIM_CTRL_RXF_TRIG_4 (0 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 4 */
+ #define CIM_CTRL_RXF_TRIG_8 (1 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 8 */
+ #define CIM_CTRL_RXF_TRIG_12 (2 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 12 */
+ #define CIM_CTRL_RXF_TRIG_16 (3 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 16 */
+ #define CIM_CTRL_RXF_TRIG_20 (4 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 20 */
+ #define CIM_CTRL_RXF_TRIG_24 (5 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 24 */
+ #define CIM_CTRL_RXF_TRIG_28 (6 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 28 */
+ #define CIM_CTRL_RXF_TRIG_32 (7 << CIM_CTRL_RXF_TRIG_BIT) /* RXFIFO Trigger Value is 32 */
+#define CIM_CTRL_DMA_EN (1 << 2)
+#define CIM_CTRL_RXF_RST (1 << 1)
+#define CIM_CTRL_ENA (1 << 0)
+
+/* CIM State Register (CIM_STATE) */
+#define CIM_STATE_DMA_SOF (1 << 6)
+#define CIM_STATE_DMA_EOF (1 << 5)
+#define CIM_STATE_DMA_STOP (1 << 4)
+#define CIM_STATE_RXF_OF (1 << 3)
+#define CIM_STATE_RXF_TRIG (1 << 2)
+#define CIM_STATE_RXF_EMPTY (1 << 1)
+#define CIM_STATE_VDD (1 << 0)
+
+/* CIM DMA Command Register (CIM_CMD) */
+#define CIM_CMD_SOFINT (1 << 31)
+#define CIM_CMD_EOFINT (1 << 30)
+#define CIM_CMD_STOP (1 << 28)
+#define CIM_CMD_LEN_BIT 0
+#define CIM_CMD_LEN_MASK (0xffffff << CIM_CMD_LEN_BIT)
+
+/* ADC Control Register */
+#define SADC_CTRL_PENDM (1 << 4) /* Pen Down Interrupt Mask */
+#define SADC_CTRL_PENUM (1 << 3) /* Pen Up Interrupt Mask */
+#define SADC_CTRL_TSRDYM (1 << 2) /* Touch Screen Data Ready Interrupt Mask */
+#define SADC_CTRL_PBATRDYM (1 << 1) /* PBAT Data Ready Interrupt Mask */
+#define SADC_CTRL_SRDYM (1 << 0) /* SADCIN Data Ready Interrupt Mask */
+
+/* ADC Status Register */
+#define SADC_STATE_TSBUSY (1 << 7) /* TS A/D is working */
+#define SADC_STATE_PBATBUSY (1 << 6) /* PBAT A/D is working */
+#define SADC_STATE_SBUSY (1 << 5) /* SADCIN A/D is working */
+#define SADC_STATE_PEND (1 << 4) /* Pen Down Interrupt Flag */
+#define SADC_STATE_PENU (1 << 3) /* Pen Up Interrupt Flag */
+#define SADC_STATE_TSRDY (1 << 2) /* Touch Screen Data Ready Interrupt Flag */
+#define SADC_STATE_PBATRDY (1 << 1) /* PBAT Data Ready Interrupt Flag */
+#define SADC_STATE_SRDY (1 << 0) /* SADCIN Data Ready Interrupt Flag */
+
+/* ADC Touch Screen Data Register */
+#define SADC_TSDAT_DATA0_BIT 0
+#define SADC_TSDAT_DATA0_MASK (0xfff << SADC_TSDAT_DATA0_BIT)
+#define SADC_TSDAT_TYPE0 (1 << 15)
+#define SADC_TSDAT_DATA1_BIT 16
+#define SADC_TSDAT_DATA1_MASK (0xfff << SADC_TSDAT_DATA1_BIT)
+#define SADC_TSDAT_TYPE1 (1 << 31)
+
+/* SLCD Control Register */
+#define SLCD_CTRL_DMA_EN (1 << 0)
+
+/* SLCD Status Register */
+#define SLCD_STATE_BUSY (1 << 0)
+
+/* SLCD Data Register */
+#define SLCD_DATA_RS_DATA (0 << 31)
+#define SLCD_DATA_RS_COMMAND (1 << 31)
+
+/* SLCD FIFO Register */
+#define SLCD_FIFO_RS_DATA (0 << 31)
+#define SLCD_FIFO_RS_COMMAND (1 << 31)
+
+/* Vertical Synchronize Register */
+#define LCD_VSYNC_VPS_BIT 16 /* VSYNC pulse start in line clock, fixed to 0 */
+#define LCD_VSYNC_VPS_MASK (0xffff << LCD_VSYNC_VPS_BIT)
+#define LCD_VSYNC_VPE_BIT 0 /* VSYNC pulse end in line clock */
+#define LCD_VSYNC_VPE_MASK (0xffff << LCD_VSYNC_VPS_BIT)
+
+/* Horizontal Synchronize Register */
+#define LCD_HSYNC_HPS_BIT 16 /* HSYNC pulse start position in dot clock */
+#define LCD_HSYNC_HPS_MASK (0xffff << LCD_HSYNC_HPS_BIT)
+#define LCD_HSYNC_HPE_BIT 0 /* HSYNC pulse end position in dot clock */
+#define LCD_HSYNC_HPE_MASK (0xffff << LCD_HSYNC_HPE_BIT)
+
+/* Virtual Area Setting Register */
+#define LCD_VAT_HT_BIT 16 /* Horizontal Total size in dot clock */
+#define LCD_VAT_HT_MASK (0xffff << LCD_VAT_HT_BIT)
+#define LCD_VAT_VT_BIT 0 /* Vertical Total size in dot clock */
+#define LCD_VAT_VT_MASK (0xffff << LCD_VAT_VT_BIT)
+
+/* Display Area Horizontal Start/End Point Register */
+#define LCD_DAH_HDS_BIT 16 /* Horizontal display area start in dot clock */
+#define LCD_DAH_HDS_MASK (0xffff << LCD_DAH_HDS_BIT)
+#define LCD_DAH_HDE_BIT 0 /* Horizontal display area end in dot clock */
+#define LCD_DAH_HDE_MASK (0xffff << LCD_DAH_HDE_BIT)
+
+/* Display Area Vertical Start/End Point Register */
+#define LCD_DAV_VDS_BIT 16 /* Vertical display area start in line clock */
+#define LCD_DAV_VDS_MASK (0xffff << LCD_DAV_VDS_BIT)
+#define LCD_DAV_VDE_BIT 0 /* Vertical display area end in line clock */
+#define LCD_DAV_VDE_MASK (0xffff << LCD_DAV_VDE_BIT)
+
+/* PS Signal Setting */
+#define LCD_PS_PSS_BIT 16 /* PS signal start position in dot clock */
+#define LCD_PS_PSS_MASK (0xffff << LCD_PS_PSS_BIT)
+#define LCD_PS_PSE_BIT 0 /* PS signal end position in dot clock */
+#define LCD_PS_PSE_MASK (0xffff << LCD_PS_PSE_BIT)
+
+/* CLS Signal Setting */
+#define LCD_CLS_CLSS_BIT 16 /* CLS signal start position in dot clock */
+#define LCD_CLS_CLSS_MASK (0xffff << LCD_CLS_CLSS_BIT)
+#define LCD_CLS_CLSE_BIT 0 /* CLS signal end position in dot clock */
+#define LCD_CLS_CLSE_MASK (0xffff << LCD_CLS_CLSE_BIT)
+
+/* SPL Signal Setting */
+#define LCD_SPL_SPLS_BIT 16 /* SPL signal start position in dot clock */
+#define LCD_SPL_SPLS_MASK (0xffff << LCD_SPL_SPLS_BIT)
+#define LCD_SPL_SPLE_BIT 0 /* SPL signal end position in dot clock */
+#define LCD_SPL_SPLE_MASK (0xffff << LCD_SPL_SPLE_BIT)
+
+/* REV Signal Setting */
+#define LCD_REV_REVS_BIT 16 /* REV signal start position in dot clock */
+#define LCD_REV_REVS_MASK (0xffff << LCD_REV_REVS_BIT)
+
+/* LCD Control Register */
+#define LCD_CTRL_BST_BIT 28 /* Burst Length Selection */
+#define LCD_CTRL_BST_MASK (0x03 << LCD_CTRL_BST_BIT)
+ #define LCD_CTRL_BST_4 (0 << LCD_CTRL_BST_BIT) /* 4-word */
+ #define LCD_CTRL_BST_8 (1 << LCD_CTRL_BST_BIT) /* 8-word */
+ #define LCD_CTRL_BST_16 (2 << LCD_CTRL_BST_BIT) /* 16-word */
+#define LCD_CTRL_RGB565 (0 << 27) /* RGB565 mode */
+#define LCD_CTRL_RGB555 (1 << 27) /* RGB555 mode */
+#define LCD_CTRL_OFUP (1 << 26) /* Output FIFO underrun protection enable */
+#define LCD_CTRL_FRC_BIT 24 /* STN FRC Algorithm Selection */
+#define LCD_CTRL_FRC_MASK (0x03 << LCD_CTRL_FRC_BIT)
+ #define LCD_CTRL_FRC_16 (0 << LCD_CTRL_FRC_BIT) /* 16 grayscale */
+ #define LCD_CTRL_FRC_4 (1 << LCD_CTRL_FRC_BIT) /* 4 grayscale */
+ #define LCD_CTRL_FRC_2 (2 << LCD_CTRL_FRC_BIT) /* 2 grayscale */
+#define LCD_CTRL_PDD_BIT 16 /* Load Palette Delay Counter */
+#define LCD_CTRL_PDD_MASK (0xff << LCD_CTRL_PDD_BIT)
+#define LCD_CTRL_EOFM (1 << 13) /* EOF interrupt mask */
+#define LCD_CTRL_SOFM (1 << 12) /* SOF interrupt mask */
+#define LCD_CTRL_OFUM (1 << 11) /* Output FIFO underrun interrupt mask */
+#define LCD_CTRL_IFUM0 (1 << 10) /* Input FIFO 0 underrun interrupt mask */
+#define LCD_CTRL_IFUM1 (1 << 9) /* Input FIFO 1 underrun interrupt mask */
+#define LCD_CTRL_LDDM (1 << 8) /* LCD disable done interrupt mask */
+#define LCD_CTRL_QDM (1 << 7) /* LCD quick disable done interrupt mask */
+#define LCD_CTRL_BEDN (1 << 6) /* Endian selection */
+#define LCD_CTRL_PEDN (1 << 5) /* Endian in byte:0-msb first, 1-lsb first */
+#define LCD_CTRL_DIS (1 << 4) /* Disable indicate bit */
+#define LCD_CTRL_ENA (1 << 3) /* LCD enable bit */
+#define LCD_CTRL_BPP_BIT 0 /* Bits Per Pixel */
+#define LCD_CTRL_BPP_MASK (0x07 << LCD_CTRL_BPP_BIT)
+ #define LCD_CTRL_BPP_1 (0 << LCD_CTRL_BPP_BIT) /* 1 bpp */
+ #define LCD_CTRL_BPP_2 (1 << LCD_CTRL_BPP_BIT) /* 2 bpp */
+ #define LCD_CTRL_BPP_4 (2 << LCD_CTRL_BPP_BIT) /* 4 bpp */
+ #define LCD_CTRL_BPP_8 (3 << LCD_CTRL_BPP_BIT) /* 8 bpp */
+ #define LCD_CTRL_BPP_16 (4 << LCD_CTRL_BPP_BIT) /* 15/16 bpp */
+ #define LCD_CTRL_BPP_18_24 (5 << LCD_CTRL_BPP_BIT) /* 18/24/32 bpp */
+
+/* Module Operation Definitions */
+#ifndef __ASSEMBLY__
+
+/*
+ * CS1#, CLE, ALE, FRE#, FWE#, FRB#, RDWE#/BUFD#
+ */
+#define __gpio_as_nand() \
+do { \
+ writel(0x02018000, GPIO_PXFUNS(1)); \
+ writel(0x02018000, GPIO_PXSELC(1)); \
+ writel(0x02018000, GPIO_PXPES(1)); \
+ writel(0x30000000, GPIO_PXFUNS(2)); \
+ writel(0x30000000, GPIO_PXSELC(2)); \
+ writel(0x30000000, GPIO_PXPES(2)); \
+ writel(0x40000000, GPIO_PXFUNC(2)); \
+ writel(0x40000000, GPIO_PXSELC(2)); \
+ writel(0x40000000, GPIO_PXDIRC(2)); \
+ writel(0x40000000, GPIO_PXPES(2)); \
+ writel(0x00400000, GPIO_PXFUNS(1)); \
+ writel(0x00400000, GPIO_PXSELC(1)); \
+} while (0)
+
+#define __gpio_as_sdram_16bit_4720() \
+do { \
+ writel(0x5442bfaa, GPIO_PXFUNS(0)); \
+ writel(0x5442bfaa, GPIO_PXSELC(0)); \
+ writel(0x5442bfaa, GPIO_PXPES(0)); \
+ writel(0x81f9ffff, GPIO_PXFUNS(1)); \
+ writel(0x81f9ffff, GPIO_PXSELC(1)); \
+ writel(0x81f9ffff, GPIO_PXPES(1)); \
+ writel(0x01000000, GPIO_PXFUNS(2)); \
+ writel(0x01000000, GPIO_PXSELC(2)); \
+ writel(0x01000000, GPIO_PXPES(2)); \
+} while (0)
+#define __gpio_as_lcd_18bit() \
+do { \
+ writel(0x003fffff, GPIO_PXFUNS(2)); \
+ writel(0x003fffff, GPIO_PXSELC(2)); \
+ writel(0x003fffff, GPIO_PXPES(2)); \
+} while (0)
+
+/*
+ * MSC_CMD, MSC_CLK, MSC_D0 ~ MSC_D3
+ */
+#define __gpio_as_msc() \
+do { \
+ writel(0x00003f00, GPIO_PXFUNS(3)); \
+ writel(0x00003f00, GPIO_PXSELC(3)); \
+ writel(0x00003f00, GPIO_PXPES(3)); \
+} while (0)
+
+#define __gpio_get_port(p) (readl(GPIO_PXPIN(p)))
+
+#define __gpio_disable_pull(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ writel((1 << o), GPIO_PXPES(p)); \
+} while (0)
+
+#define __gpio_enable_pull(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ writel(1 << (o), GPIO_PXPEC(p)); \
+} while (0)
+
+#define __gpio_port_as_output(p, o) \
+do { \
+ writel(1 << (o), GPIO_PXFUNC(p)); \
+ writel(1 << (o), GPIO_PXSELC(p)); \
+ writel(1 << (o), GPIO_PXDIRS(p)); \
+} while (0)
+
+#define __gpio_port_as_input(p, o) \
+do { \
+ writel(1 << (o), GPIO_PXFUNC(p)); \
+ writel(1 << (o), GPIO_PXSELC(p)); \
+ writel(1 << (o), GPIO_PXDIRC(p)); \
+} while (0)
+
+#define __gpio_as_output(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ __gpio_port_as_output(p, o); \
+} while (0)
+
+#define __gpio_as_input(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ __gpio_port_as_input(p, o); \
+} while (0)
+
+#define __gpio_set_pin(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ writel((1 << o), GPIO_PXDATS(p)); \
+} while (0)
+
+#define __gpio_clear_pin(n) \
+do { \
+ unsigned int p, o; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ writel((1 << o), GPIO_PXDATC(p)); \
+} while (0)
+
+#define __gpio_get_pin(n) \
+({ \
+ unsigned int p, o, v; \
+ p = (n) / 32; \
+ o = (n) % 32; \
+ if (__gpio_get_port(p) & (1 << o)) \
+ v = 1; \
+ else \
+ v = 0; \
+ v; \
+})
+
+#define __gpio_as_uart0() \
+do { \
+ writel(0x06000000, GPIO_PXFUNS(3)); \
+ writel(0x06000000, GPIO_PXSELS(3)); \
+ writel(0x06000000, GPIO_PXPES(3)); \
+} while (0)
+
+#define __gpio_jtag_to_uart0() \
+do { \
+ writel(0x80000000, GPIO_PXSELS(2)); \
+} while (0)
+
+/* Clock Control Register */
+#define __cpm_get_pllm() \
+ ((readl(CPM_CPPCR) & CPM_CPPCR_PLLM_MASK) >> CPM_CPPCR_PLLM_BIT)
+#define __cpm_get_plln() \
+ ((readl(CPM_CPPCR) & CPM_CPPCR_PLLN_MASK) >> CPM_CPPCR_PLLN_BIT)
+#define __cpm_get_pllod() \
+ ((readl(CPM_CPPCR) & CPM_CPPCR_PLLOD_MASK) >> CPM_CPPCR_PLLOD_BIT)
+#define __cpm_get_hdiv() \
+ ((readl(CPM_CPCCR) & CPM_CPCCR_HDIV_MASK) >> CPM_CPCCR_HDIV_BIT)
+#define __cpm_get_pdiv() \
+ ((readl(CPM_CPCCR) & CPM_CPCCR_PDIV_MASK) >> CPM_CPCCR_PDIV_BIT)
+#define __cpm_get_cdiv() \
+ ((readl(CPM_CPCCR) & CPM_CPCCR_CDIV_MASK) >> CPM_CPCCR_CDIV_BIT)
+#define __cpm_get_mdiv() \
+ ((readl(CPM_CPCCR) & CPM_CPCCR_MDIV_MASK) >> CPM_CPCCR_MDIV_BIT)
+
+static __inline__ unsigned int __cpm_get_pllout(void)
+{
+ unsigned long m, n, no, pllout;
+ unsigned long cppcr = readl(CPM_CPPCR);
+ unsigned long od[4] = {1, 2, 2, 4};
+
+ if ((cppcr & CPM_CPPCR_PLLEN) && !(cppcr & CPM_CPPCR_PLLBP)) {
+ m = __cpm_get_pllm() + 2;
+ n = __cpm_get_plln() + 2;
+ no = od[__cpm_get_pllod()];
+ pllout = (CONFIG_SYS_EXTAL / (n * no)) * m;
+ } else
+ pllout = CONFIG_SYS_EXTAL;
+
+ return pllout;
+}
+
+
+#define __cpm_stop_all() writel(0x7fff, CPM_CLKGR)
+#define __cpm_stop_uart1() writel(readl(CPM_CLKGR) |= CPM_CLKGR_UART1, CPM_CLKGR)
+#define __cpm_stop_uhc() writel(readl(CPM_CLKGR) |= CPM_CLKGR_UHC, CPM_CLKGR)
+#define __cpm_stop_ipu() writel(readl(CPM_CLKGR) |= CPM_CLKGR_IPU, CPM_CLKGR)
+#define __cpm_stop_dmac() writel(readl(CPM_CLKGR) |= CPM_CLKGR_DMAC, CPM_CLKGR)
+#define __cpm_stop_udc() writel(readl(CPM_CLKGR) |= CPM_CLKGR_UDC, CPM_CLKGR)
+#define __cpm_stop_lcd() writel(readl(CPM_CLKGR) |= CPM_CLKGR_LCD, CPM_CLKGR)
+#define __cpm_stop_cim() writel(readl(CPM_CLKGR) |= CPM_CLKGR_CIM, CPM_CLKGR)
+#define __cpm_stop_sadc() writel(readl(CPM_CLKGR) |= CPM_CLKGR_SADC, CPM_CLKGR)
+#define __cpm_stop_msc() writel(readl(CPM_CLKGR) |= CPM_CLKGR_MSC, CPM_CLKGR)
+#define __cpm_stop_aic1() writel(readl(CPM_CLKGR) |= CPM_CLKGR_AIC1, CPM_CLKGR)
+#define __cpm_stop_aic2() writel(readl(CPM_CLKGR) |= CPM_CLKGR_AIC2, CPM_CLKGR)
+#define __cpm_stop_ssi() writel(readl(CPM_CLKGR) |= CPM_CLKGR_SSI, CPM_CLKGR)
+#define __cpm_stop_i2c() writel(readl(CPM_CLKGR) |= CPM_CLKGR_I2C, CPM_CLKGR)
+#define __cpm_stop_rtc() writel(readl(CPM_CLKGR) |= CPM_CLKGR_RTC, CPM_CLKGR)
+#define __cpm_stop_tcu() writel(readl(CPM_CLKGR) |= CPM_CLKGR_TCU, CPM_CLKGR)
+#define __cpm_stop_uart0() writel(readl(CPM_CLKGR) |= CPM_CLKGR_UART0, CPM_CLKGR)
+
+#define __wdt_start() writeb(readb(WDT_TCER) | WDT_TCER_TCEN, WDT_TCER)
+#define __wdt_stop() writeb(readb(WDT_TCER) & ~WDT_TCER_TCEN, WDT_TCER)
+#define __wdt_set_count(v) writew((v), WDT_TCNT)
+#define __wdt_set_data(v) writew((v), WDT_TDR)
+#define __wdt_select_extalclk() \
+ (writew((readw(WDT_TCSR) & \
+ ~(WDT_TCSR_EXT_EN | WDT_TCSR_RTC_EN | \
+ WDT_TCSR_PCK_EN)) \
+ | WDT_TCSR_EXT_EN, WDT_TCSR))
+#define __wdt_select_clk_div64() \
+ (writew((readw(WDT_TCSR) & \
+ ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE64, WDT_TCSR))
+#define __tcu_start_wdt_clock() (writew(TCU_TSSR_WDTSC, TCU_TSCR))
+
+#define __rtc_write_ready() (readl(RTC_RCR) & RTC_RCR_WRDY)
+#define __rtc_enable_alarm() \
+do{ \
+ while(!__rtc_write_ready()); \
+ writel(readl(RTC_RCR) | RTC_RCR_AE, RTC_RCR); \
+}while(0)
+
+#endif /* !__ASSEMBLY__ */
+#endif /* __JZ4740_H__ */
--
1.7.0.4
More information about the U-Boot
mailing list