[U-Boot] [PATCH 3/4] powerpc/85xx: Remove support for PM854/PM856 boards

Kumar Gala galak at kernel.crashing.org
Tue Dec 14 05:12:45 CET 2010


The PM854/PM856 boards are no longer maintained and thus we are removing
support for them.

Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
 board/pm854/Makefile    |   53 ------
 board/pm854/ddr.c       |   73 --------
 board/pm854/law.c       |   58 ------
 board/pm854/pm854.c     |  298 -------------------------------
 board/pm854/tlb.c       |  117 ------------
 board/pm856/Makefile    |   53 ------
 board/pm856/ddr.c       |   73 --------
 board/pm856/law.c       |   58 ------
 board/pm856/pm856.c     |  453 -----------------------------------------------
 board/pm856/tlb.c       |  117 ------------
 boards.cfg              |    2 -
 include/configs/PM854.h |  426 --------------------------------------------
 include/configs/PM856.h |  429 --------------------------------------------
 13 files changed, 0 insertions(+), 2210 deletions(-)
 delete mode 100644 board/pm854/Makefile
 delete mode 100644 board/pm854/ddr.c
 delete mode 100644 board/pm854/law.c
 delete mode 100644 board/pm854/pm854.c
 delete mode 100644 board/pm854/tlb.c
 delete mode 100644 board/pm856/Makefile
 delete mode 100644 board/pm856/ddr.c
 delete mode 100644 board/pm856/law.c
 delete mode 100644 board/pm856/pm856.c
 delete mode 100644 board/pm856/tlb.c
 delete mode 100644 include/configs/PM854.h
 delete mode 100644 include/configs/PM856.h

diff --git a/board/pm854/Makefile b/board/pm854/Makefile
deleted file mode 100644
index 9f623a2..0000000
--- a/board/pm854/Makefile
+++ /dev/null
@@ -1,53 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS-y	+= $(BOARD).o
-COBJS-y	+= law.o
-COBJS-y	+= tlb.o
-COBJS-$(CONFIG_FSL_DDR1) += ddr.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS-y))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $(OBJS))
-
-clean:
-	rm -f $(OBJS) $(SOBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/pm854/ddr.c b/board/pm854/ddr.c
deleted file mode 100644
index 7850794..0000000
--- a/board/pm854/ddr.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * Version 2 as published by the Free Software Foundation.
- */
-
-#include <common.h>
-#include <i2c.h>
-
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
-
-static void
-get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
-{
-	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
-}
-
-
-unsigned int
-fsl_ddr_get_mem_data_rate(void)
-{
-	return get_ddr_freq(0);
-}
-
-
-void
-fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
-		      unsigned int ctrl_num)
-{
-	unsigned int i;
-	unsigned int i2c_address = 0;
-
-	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
-		if (ctrl_num == 0 && i == 0) {
-			i2c_address = SPD_EEPROM_ADDRESS;
-		}
-		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
-	}
-}
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	/*
-	 * Factors to consider for CPO:
-	 *	- frequency
-	 *	- ddr1 vs. ddr2
-	 */
-	popts->cpo_override = 0;
-
-	/*
-	 * Factors to consider for write data delay:
-	 *	- number of DIMMs
-	 *
-	 * 1 = 1/4 clock delay
-	 * 2 = 1/2 clock delay
-	 * 3 = 3/4 clock delay
-	 * 4 = 1   clock delay
-	 * 5 = 5/4 clock delay
-	 * 6 = 3/2 clock delay
-	 */
-	popts->write_data_delay = 3;
-
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 0;
-}
diff --git a/board/pm854/law.c b/board/pm854/law.c
deleted file mode 100644
index ac21d7a..0000000
--- a/board/pm854/law.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- * 0x0000_0000     0x7fff_ffff     DDR                     2G
- * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
- * 0xc000_0000     0xdfff_ffff     RapidIO                 512M
- * 0xe000_0000     0xe000_ffff     CCSR                    1M
- * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
- * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
- * 0xf800_0000     0xf80f_ffff     BCSR                    1M
- * 0xfc00_0000     0xffff_ffff     FLASH (boot bank)       64M
- *
- * Notes:
- *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- *    If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
-#ifndef CONFIG_SPD_EEPROM
-	SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
-#endif
-	SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
-	/* This is not so much the SDRAM map as it is the whole localbus map. */
-	SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
-	SET_LAW(CONFIG_SYS_RIO_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_RIO),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/pm854/pm854.c b/board/pm854/pm854.c
deleted file mode 100644
index 0b8ea81..0000000
--- a/board/pm854/pm854.c
+++ /dev/null
@@ -1,298 +0,0 @@
- /*
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003, Motorola Inc.
- * Xianghua Xiao, (X.Xiao at motorola.com)
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt at artesyncp.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-
-#include <common.h>
-#include <pci.h>
-#include <netdev.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <spd_sdram.h>
-
-#if defined(CONFIG_DDR_ECC)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
-void local_bus_init(void);
-void sdram_init(void);
-long int fixed_sdram(void);
-
-
-int board_early_init_f (void)
-{
-#if defined(CONFIG_PCI)
-    volatile ccsr_pcix_t *pci = (void *)(CONFIG_SYS_MPC85xx_PCIX_ADDR);
-
-    pci->peer &= 0xffffffdf; /* disable master abort */
-#endif
-
-    return 0;
-}
-
-int checkboard (void)
-{
-	puts("Board: MicroSys PM854\n");
-
-#ifdef CONFIG_PCI
-	printf("PCI1: 32 bit, %d MHz (compiled)\n",
-	       CONFIG_SYS_CLK_FREQ / 1000000);
-#else
-	printf("PCI1: disabled\n");
-#endif
-
-	/*
-	 * Initialize local bus.
-	 */
-	local_bus_init();
-
-	return 0;
-}
-
-
-phys_size_t
-initdram(int board_type)
-{
-	long dram_size = 0;
-
-	puts("Initializing\n");
-
-#if defined(CONFIG_DDR_DLL)
-	{
-	    volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	    int i,x;
-
-	    x = 10;
-
-	    /*
-	     * Work around to stabilize DDR DLL
-	     */
-	    gur->ddrdllcr = 0x81000000;
-	    asm("sync;isync;msync");
-	    udelay (200);
-	    while (gur->ddrdllcr != 0x81000100)
-	    {
-		gur->devdisr = gur->devdisr | 0x00010000;
-		asm("sync;isync;msync");
-		for (i=0; i<x; i++)
-		    ;
-		gur->devdisr = gur->devdisr & 0xfff7ffff;
-		asm("sync;isync;msync");
-		x++;
-	    }
-	}
-#endif
-
-#if defined(CONFIG_SPD_EEPROM)
-	dram_size = fsl_ddr_sdram();
-	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
-	dram_size *= 0x100000;
-#else
-	dram_size = fixed_sdram ();
-#endif
-
-#if defined(CONFIG_DDR_ECC)
-	/*
-	 * Initialize and enable DDR ECC.
-	 */
-	ddr_enable_ecc(dram_size);
-#endif
-	puts("    DDR: ");
-	return dram_size;
-}
-
-
-/*
- * Initialize Local Bus
- */
-
-void
-local_bus_init(void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
-	uint clkdiv;
-	uint lbc_hz;
-	sys_info_t sysinfo;
-
-	/*
-	 * Errata LBC11.
-	 * Fix Local Bus clock glitch when DLL is enabled.
-	 *
-	 * If localbus freq is < 66MHz, DLL bypass mode must be used.
-	 * If localbus freq is > 133MHz, DLL can be safely enabled.
-	 * Between 66 and 133, the DLL is enabled with an override workaround.
-	 */
-
-	get_sys_info(&sysinfo);
-	clkdiv = lbc->lcrr & LCRR_CLKDIV;
-	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
-
-	if (lbc_hz < 66) {
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000;	/* DLL Bypass */
-
-	} else if (lbc_hz >= 133) {
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
-
-	} else {
-		/*
-		 * On REV1 boards, need to change CLKDIV before enable DLL.
-		 * Default CLKDIV is 8, change it to 4 temporarily.
-		 */
-		uint pvr = get_pvr();
-		uint temp_lbcdll = 0;
-
-		if (pvr == PVR_85xx_REV1) {
-			/* FIXME: Justify the high bit here. */
-			lbc->lcrr = 0x10000004;
-		}
-
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
-		udelay(200);
-
-		/*
-		 * Sample LBC DLL ctrl reg, upshift it to set the
-		 * override bits.
-		 */
-		temp_lbcdll = gur->lbcdllcr;
-		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
-		asm("sync;isync;msync");
-	}
-}
-
-
-#if defined(CONFIG_SYS_DRAM_TEST)
-int testdram (void)
-{
-	uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
-	uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
-	uint *p;
-
-	printf("SDRAM test phase 1:\n");
-	for (p = pstart; p < pend; p++)
-		*p = 0xaaaaaaaa;
-
-	for (p = pstart; p < pend; p++) {
-		if (*p != 0xaaaaaaaa) {
-			printf ("SDRAM test fails at: %08x\n", (uint) p);
-			return 1;
-		}
-	}
-
-	printf("SDRAM test phase 2:\n");
-	for (p = pstart; p < pend; p++)
-		*p = 0x55555555;
-
-	for (p = pstart; p < pend; p++) {
-		if (*p != 0x55555555) {
-			printf ("SDRAM test fails at: %08x\n", (uint) p);
-			return 1;
-		}
-	}
-
-	printf("SDRAM test passed.\n");
-	return 0;
-}
-#endif
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- *  fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-long int fixed_sdram (void)
-{
-  #ifndef CONFIG_SYS_RAMBOOT
-	volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
-
-	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
-	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
-	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
-	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-	ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
-	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-    #if defined (CONFIG_DDR_ECC)
-	ddr->err_disable = 0x0000000D;
-	ddr->err_sbe = 0x00ff0000;
-    #endif
-	asm("sync;isync;msync");
-	udelay(500);
-    #if defined (CONFIG_DDR_ECC)
-	/* Enable ECC checking */
-	ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
-    #else
-	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
-    #endif
-	asm("sync; isync; msync");
-	udelay(500);
-  #endif
-	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-}
-#endif	/* !defined(CONFIG_SPD_EEPROM) */
-
-
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_pm854_config_table[] = {
-    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-      PCI_IDSEL_NUMBER, PCI_ANY_ID,
-      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
-				   PCI_ENET0_MEMADDR,
-				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
-      } },
-    { }
-};
-#endif
-
-
-static struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
-	config_table: pci_pm854_config_table,
-#endif
-};
-
-#endif	/* CONFIG_PCI */
-
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
-	pci_mpc85xx_init(&hose);
-#endif /* CONFIG_PCI */
-}
-
-int board_eth_init(bd_t *bis)
-{
-	cpu_eth_init(bis);	/* Intialize TSECs first */
-	return pci_eth_init(bis);
-}
diff --git a/board/pm854/tlb.c b/board/pm854/tlb.c
deleted file mode 100644
index 5e74e2d..0000000
--- a/board/pm854/tlb.c
+++ /dev/null
@@ -1,117 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
-	/*
-	 * TLB 0:	64M	Non-cacheable, guarded
-	 * 0xfc000000	64M	FLASH (8,16,32 or 64 MB)
-	 * Out of reset this entry is only 4K.
-	 */
-	SET_TLB_ENTRY(1, 0xfc000000, 0xfc000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_16M, 1),
-
-	/*
-	 * TLB 1:	256M	Non-cacheable, guarded
-	 * 0x80000000	256M	PCI1 MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 2:	256M	Non-cacheable, guarded
-	 * 0x90000000	256M	PCI1 MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 3:	256M	Non-cacheable, guarded
-	 * 0xc0000000	256M	Rapid IO MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE, CONFIG_SYS_RIO_MEM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 4:	256M	Non-cacheable, guarded
-	 * 0xd0000000	256M	Rapid IO MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE + 0x10000000, CONFIG_SYS_RIO_MEM_BASE + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 5:	64M	Non-cacheable, guarded
-	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	16M	PCI1 IO
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLB 6:	64M	Cacheable, non-guarded
-	 * 0xf000_0000	64M	LBC SDRAM
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 6, BOOKE_PAGESZ_64M, 1),
-
-#if !defined(CONFIG_SPD_EEPROM)
-	/*
-	 * TLB 7:	256M	DDR
-	 * 0x00000000	256M	DDR System memory
-	 * Without SPD EEPROM configured DDR, this must be setup manually.
-	 * Make sure the TLB count at the top of this table is correct.
-	 * Likely it needs to be increased by two for these entries.
-	 */
-
-	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 7, BOOKE_PAGESZ_256M, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/pm856/Makefile b/board/pm856/Makefile
deleted file mode 100644
index 9f623a2..0000000
--- a/board/pm856/Makefile
+++ /dev/null
@@ -1,53 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS-y	+= $(BOARD).o
-COBJS-y	+= law.o
-COBJS-y	+= tlb.o
-COBJS-$(CONFIG_FSL_DDR1) += ddr.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS-y))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $(OBJS))
-
-clean:
-	rm -f $(OBJS) $(SOBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/pm856/ddr.c b/board/pm856/ddr.c
deleted file mode 100644
index 7850794..0000000
--- a/board/pm856/ddr.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * Version 2 as published by the Free Software Foundation.
- */
-
-#include <common.h>
-#include <i2c.h>
-
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
-
-static void
-get_spd(ddr1_spd_eeprom_t *spd, unsigned char i2c_address)
-{
-	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr1_spd_eeprom_t));
-}
-
-
-unsigned int
-fsl_ddr_get_mem_data_rate(void)
-{
-	return get_ddr_freq(0);
-}
-
-
-void
-fsl_ddr_get_spd(ddr1_spd_eeprom_t *ctrl_dimms_spd,
-		      unsigned int ctrl_num)
-{
-	unsigned int i;
-	unsigned int i2c_address = 0;
-
-	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
-		if (ctrl_num == 0 && i == 0) {
-			i2c_address = SPD_EEPROM_ADDRESS;
-		}
-		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
-	}
-}
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	/*
-	 * Factors to consider for CPO:
-	 *	- frequency
-	 *	- ddr1 vs. ddr2
-	 */
-	popts->cpo_override = 0;
-
-	/*
-	 * Factors to consider for write data delay:
-	 *	- number of DIMMs
-	 *
-	 * 1 = 1/4 clock delay
-	 * 2 = 1/2 clock delay
-	 * 3 = 3/4 clock delay
-	 * 4 = 1   clock delay
-	 * 5 = 5/4 clock delay
-	 * 6 = 3/2 clock delay
-	 */
-	popts->write_data_delay = 3;
-
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 0;
-}
diff --git a/board/pm856/law.c b/board/pm856/law.c
deleted file mode 100644
index ac21d7a..0000000
--- a/board/pm856/law.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-/*
- * LAW(Local Access Window) configuration:
- *
- * 0x0000_0000     0x7fff_ffff     DDR                     2G
- * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
- * 0xc000_0000     0xdfff_ffff     RapidIO                 512M
- * 0xe000_0000     0xe000_ffff     CCSR                    1M
- * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
- * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
- * 0xf800_0000     0xf80f_ffff     BCSR                    1M
- * 0xfc00_0000     0xffff_ffff     FLASH (boot bank)       64M
- *
- * Notes:
- *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- *    If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-struct law_entry law_table[] = {
-#ifndef CONFIG_SPD_EEPROM
-	SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
-#endif
-	SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
-	/* This is not so much the SDRAM map as it is the whole localbus map. */
-	SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
-	SET_LAW(CONFIG_SYS_RIO_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_RIO),
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c
deleted file mode 100644
index 4e059b0..0000000
--- a/board/pm856/pm856.c
+++ /dev/null
@@ -1,453 +0,0 @@
-/*
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2003,Motorola Inc.
- * Xianghua Xiao, (X.Xiao at motorola.com)
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt at artesyncp.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-
-#include <common.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <ioports.h>
-#include <spd_sdram.h>
-#include <miiphy.h>
-#include <netdev.h>
-
-#if defined(CONFIG_DDR_ECC)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-
-void local_bus_init(void);
-long int fixed_sdram(void);
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
-    /* Port A configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PA31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxENB */
-	/* PA30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 TxClav   */
-	/* PA29 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxSOC  */
-	/* PA28 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 RxENB */
-	/* PA27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxSOC */
-	/* PA26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxClav */
-	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
-	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
-	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
-	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
-	/* PA21 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[4] */
-	/* PA20 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[5] */
-	/* PA19 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[6] */
-	/* PA18 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[7] */
-	/* PA17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[7] */
-	/* PA16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[6] */
-	/* PA15 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[5] */
-	/* PA14 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[4] */
-	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
-	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
-	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
-	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
-	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
-	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
-	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
-	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
-	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
-	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
-	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
-	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
-	/* PA1  */ {   0,   0,   0,   0,   0,   0   }, /* FREERUN */
-	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
-    },
-
-    /* Port B configuration */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PB31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
-	/* PB30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
-	/* PB29 */ {   0,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
-	/* PB28 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
-	/* PB27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
-	/* PB26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
-	/* PB25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
-	/* PB24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
-	/* PB23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
-	/* PB22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
-	/* PB21 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
-	/* PB20 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
-	/* PB19 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
-	/* PB18 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
-	/* PB17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
-	/* PB16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
-	/* PB15 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
-	/* PB14 */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
-	/* PB13 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:COL */
-	/* PB12 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
-	/* PB11 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB10 */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB9  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB8  */ {   1,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
-	/* PB7  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB6  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB5  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB4  */ {   1,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
-	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    },
-
-    /* Port C */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
-	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
-	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
-	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
-	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
-	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
-	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
-	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
-	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
-	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
-	/* PC21 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
-	/* PC20 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
-	/* PC19 */ {   0,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
-	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
-	/* PC17 */ {   1,   1,   0,   0,   0,   0   }, /* PC17 */
-	/* PC16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
-	/* PC15 */ {   0,   1,   0,   0,   0,   0   }, /* PC15 */
-	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
-	/* PC13 */ {   0,   1,   0,   0,   0,   0   }, /* PC13 */
-	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
-	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
-	/* PC10 */ {   0,   0,   0,   1,   0,   0   }, /* FETHMDC */
-	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FETHMDIO */
-	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
-	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
-	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
-	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
-	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
-	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
-	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
-	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
-	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
-    },
-
-    /* Port D */
-    {   /*            conf ppar psor pdir podr pdat */
-	/* PD31 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
-	/* PD30 */ {   1,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
-	/* PD29 */ {   1,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
-	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* PD28 */
-	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* PD27 */
-	/* PD26 */ {   1,   1,   0,   1,   0,   0   }, /* PD26 */
-	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
-	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
-	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
-	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
-	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
-	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
-	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
-	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
-	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
-	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-	/* PD15 */ {   0,   1,   1,   0,   1,   0   }, /* I2C SDA */
-	/* PD14 */ {   0,   0,   0,   1,   0,   0   }, /* LED */
-	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
-	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
-	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
-	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
-	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
-	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
-	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
-	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
-	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
-	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
-	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
-	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
-    }
-};
-
-
-int board_early_init_f (void)
-{
-    return 0;
-}
-
-void reset_phy (void)
-{
-}
-
-
-int checkboard (void)
-{
-	puts("Board: MicroSys PM856\n");
-
-#ifdef CONFIG_PCI
-	printf("PCI1: 32 bit, %d MHz (compiled)\n",
-	       CONFIG_SYS_CLK_FREQ / 1000000);
-#else
-	printf("PCI1: disabled\n");
-#endif
-
-	/*
-	 * Initialize local bus.
-	 */
-	local_bus_init();
-
-	return 0;
-}
-
-
-phys_size_t
-initdram(int board_type)
-{
-	long dram_size = 0;
-
-
-	puts("Initializing\n");
-
-#if defined(CONFIG_DDR_DLL)
-	{
-	    volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	    int i,x;
-
-	    x = 10;
-
-	    /*
-	     * Work around to stabilize DDR DLL
-	     */
-	    gur->ddrdllcr = 0x81000000;
-	    asm("sync;isync;msync");
-	    udelay (200);
-	    while (gur->ddrdllcr != 0x81000100)
-	    {
-		gur->devdisr = gur->devdisr | 0x00010000;
-		asm("sync;isync;msync");
-		for (i=0; i<x; i++)
-		    ;
-		gur->devdisr = gur->devdisr & 0xfff7ffff;
-		asm("sync;isync;msync");
-		x++;
-	    }
-	}
-#endif
-
-#if defined(CONFIG_SPD_EEPROM)
-	dram_size = fsl_ddr_sdram();
-	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
-	dram_size *= 0x100000;
-#else
-	dram_size = fixed_sdram ();
-#endif
-
-#if defined(CONFIG_DDR_ECC)
-	/*
-	 * Initialize and enable DDR ECC.
-	 */
-	ddr_enable_ecc(dram_size);
-#endif
-
-	puts("    DDR: ");
-	return dram_size;
-}
-
-
-/*
- * Initialize Local Bus
- */
-
-void
-local_bus_init(void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
-
-	uint clkdiv;
-	uint lbc_hz;
-	sys_info_t sysinfo;
-
-	/*
-	 * Errata LBC11.
-	 * Fix Local Bus clock glitch when DLL is enabled.
-	 *
-	 * If localbus freq is < 66MHz, DLL bypass mode must be used.
-	 * If localbus freq is > 133MHz, DLL can be safely enabled.
-	 * Between 66 and 133, the DLL is enabled with an override workaround.
-	 */
-
-	get_sys_info(&sysinfo);
-	clkdiv = lbc->lcrr & LCRR_CLKDIV;
-	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
-
-	if (lbc_hz < 66) {
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000;	/* DLL Bypass */
-
-	} else if (lbc_hz >= 133) {
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
-
-	} else {
-		/*
-		 * On REV1 boards, need to change CLKDIV before enable DLL.
-		 * Default CLKDIV is 8, change it to 4 temporarily.
-		 */
-		uint pvr = get_pvr();
-		uint temp_lbcdll = 0;
-
-		if (pvr == PVR_85xx_REV1) {
-			/* FIXME: Justify the high bit here. */
-			lbc->lcrr = 0x10000004;
-		}
-
-		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000);/* DLL Enabled */
-		udelay(200);
-
-		/*
-		 * Sample LBC DLL ctrl reg, upshift it to set the
-		 * override bits.
-		 */
-		temp_lbcdll = gur->lbcdllcr;
-		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
-		asm("sync;isync;msync");
-	}
-}
-
-#if defined(CONFIG_SYS_DRAM_TEST)
-int testdram (void)
-{
-	uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
-	uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
-	uint *p;
-
-	printf("SDRAM test phase 1:\n");
-	for (p = pstart; p < pend; p++)
-		*p = 0xaaaaaaaa;
-
-	for (p = pstart; p < pend; p++) {
-		if (*p != 0xaaaaaaaa) {
-			printf ("SDRAM test fails at: %08x\n", (uint) p);
-			return 1;
-		}
-	}
-
-	printf("SDRAM test phase 2:\n");
-	for (p = pstart; p < pend; p++)
-		*p = 0x55555555;
-
-	for (p = pstart; p < pend; p++) {
-		if (*p != 0x55555555) {
-			printf ("SDRAM test fails at: %08x\n", (uint) p);
-			return 1;
-		}
-	}
-
-	printf("SDRAM test passed.\n");
-	return 0;
-}
-#endif
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- *  fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-long int fixed_sdram (void)
-{
-  #ifndef CONFIG_SYS_RAMBOOT
-	volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
-
-	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
-	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
-	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
-	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
-	ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
-	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-    #if defined (CONFIG_DDR_ECC)
-	ddr->err_disable = 0x0000000D;
-	ddr->err_sbe = 0x00ff0000;
-    #endif
-	asm("sync;isync;msync");
-	udelay(500);
-    #if defined (CONFIG_DDR_ECC)
-	/* Enable ECC checking */
-	ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
-    #else
-	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
-    #endif
-	asm("sync; isync; msync");
-	udelay(500);
-  #endif
-	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-}
-#endif	/* !defined(CONFIG_SPD_EEPROM) */
-
-
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc85xxads_config_table[] = {
-    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-      PCI_IDSEL_NUMBER, PCI_ANY_ID,
-      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
-				   PCI_ENET0_MEMADDR,
-				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
-      } },
-    { }
-};
-#endif
-
-
-static struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
-	config_table: pci_mpc85xxads_config_table,
-#endif
-};
-
-#endif	/* CONFIG_PCI */
-
-
-void
-pci_init_board(void)
-{
-#ifdef CONFIG_PCI
-	pci_mpc85xx_init(&hose);
-#endif /* CONFIG_PCI */
-}
-
-int board_eth_init(bd_t *bis)
-{
-	cpu_eth_init(bis);	/* Intialize TSECs first */
-	return pci_eth_init(bis);
-}
diff --git a/board/pm856/tlb.c b/board/pm856/tlb.c
deleted file mode 100644
index 5e74e2d..0000000
--- a/board/pm856/tlb.c
+++ /dev/null
@@ -1,117 +0,0 @@
-/*
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-
-	/*
-	 * TLB 0:	64M	Non-cacheable, guarded
-	 * 0xfc000000	64M	FLASH (8,16,32 or 64 MB)
-	 * Out of reset this entry is only 4K.
-	 */
-	SET_TLB_ENTRY(1, 0xfc000000, 0xfc000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_16M, 1),
-
-	/*
-	 * TLB 1:	256M	Non-cacheable, guarded
-	 * 0x80000000	256M	PCI1 MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS, CONFIG_SYS_PCI1_MEM_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 2:	256M	Non-cacheable, guarded
-	 * 0x90000000	256M	PCI1 MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000, CONFIG_SYS_PCI1_MEM_PHYS + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 3:	256M	Non-cacheable, guarded
-	 * 0xc0000000	256M	Rapid IO MEM First half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE, CONFIG_SYS_RIO_MEM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 4:	256M	Non-cacheable, guarded
-	 * 0xd0000000	256M	Rapid IO MEM Second half
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_RIO_MEM_BASE + 0x10000000, CONFIG_SYS_RIO_MEM_BASE + 0x10000000,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_256M, 1),
-
-	/*
-	 * TLB 5:	64M	Non-cacheable, guarded
-	 * 0xe000_0000	1M	CCSRBAR
-	 * 0xe200_0000	16M	PCI1 IO
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 5, BOOKE_PAGESZ_64M, 1),
-
-	/*
-	 * TLB 6:	64M	Cacheable, non-guarded
-	 * 0xf000_0000	64M	LBC SDRAM
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBC_SDRAM_BASE, CONFIG_SYS_LBC_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 6, BOOKE_PAGESZ_64M, 1),
-
-#if !defined(CONFIG_SPD_EEPROM)
-	/*
-	 * TLB 7:	256M	DDR
-	 * 0x00000000	256M	DDR System memory
-	 * Without SPD EEPROM configured DDR, this must be setup manually.
-	 * Make sure the TLB count at the top of this table is correct.
-	 * Likely it needs to be increased by two for these entries.
-	 */
-
-	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
-		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
-		      0, 7, BOOKE_PAGESZ_256M, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 34697cc..b7587f4 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -436,8 +436,6 @@ MVBLM7                       powerpc     mpc83xx     mvblm7              matrix_
 SIMPC8313_LP                 powerpc     mpc83xx     simpc8313           sheldon        -           SIMPC8313:NAND_LP
 SIMPC8313_SP                 powerpc     mpc83xx     simpc8313           sheldon        -           SIMPC8313:NAND_SP
 TQM834x                      powerpc     mpc83xx     tqm834x             tqc
-PM854                        powerpc     mpc85xx     pm854
-PM856                        powerpc     mpc85xx     pm856
 sbc8540                      powerpc     mpc85xx     sbc8560             -              -           SBC8540
 sbc8540_33                   powerpc     mpc85xx     sbc8560             -              -           SBC8540
 sbc8540_66                   powerpc     mpc85xx     sbc8560             -              -           SBC8540
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
deleted file mode 100644
index 1e2089f..0000000
--- a/include/configs/PM854.h
+++ /dev/null
@@ -1,426 +0,0 @@
-/*
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao at motorola.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * pm854 board configuration file
- *
- * Please refer to doc/README.mpc85xx for more info.
- *
- * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
-#define CONFIG_MPC8540		1	/* MPC8540 specific */
-#define CONFIG_PM854		1	/* PM854 board specific */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff80000
-
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
-/*
- * sysclk for MPC85xx
- *
- * Two valid values are:
- *    33000000
- *    66000000
- *
- * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here, so that is now the default.
- * The board, however, can run at 66MHz.  In any event, this value
- * must match the settings of some switches.  Details can be found
- * in the README.mpc85xxads.
- */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	66000000
-#endif
-
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
-
-#undef	CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
-
-
-/* DDR Setup */
-#define CONFIG_FSL_DDR1
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_SPD
-#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
-#define CONFIG_DDR_ECC			    /* only for ECC DDR module */
-#define CONFIG_FSL_DMA			    /* use DMA to init DDR ECC  */
-
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x58	/* CTLR 0 DIMM 0 */
-
-/* Manually set up DDR parameters */
-#define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256 MB */
-#define CONFIG_SYS_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80000102
-#define CONFIG_SYS_DDR_TIMING_1	0x47444321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-#define CONFIG_SYS_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	0		/* LBC SDRAM is 0 MB */
-
-#define CONFIG_SYS_FLASH_BASE		0xfe000000	/* start of 32 MB FLASH */
-#define CONFIG_SYS_BR0_PRELIM		0xfe001801	/* port size 32bit */
-
-#define CONFIG_SYS_OR0_PRELIM		0xfe006f67	/* 32 MB Flash */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef	CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_LBC_LCRR		0x00030004    /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT		0x20000000    /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR		0x20000000    /* LB refresh timer prescal*/
-
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_INDEX     1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * I2C
- */
-#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x58
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
-/* RapidIO MMU */
-#define CONFIG_SYS_RIO_MEM_BASE	0xc0000000	/* base address */
-#define CONFIG_SYS_RIO_MEM_PHYS	CONFIG_SYS_RIO_MEM_BASE
-#define CONFIG_SYS_RIO_MEM_SIZE	0x20000000	/* 128M */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE	0xe2000000
-#define CONFIG_SYS_PCI1_IO_PHYS	CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE	0x1000000	/* 16M */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
-#define CONFIG_EEPRO100
-#define	CONFIG_E1000
-#undef	CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
-    #define PCI_ENET0_IOADDR	0xe0000000
-    #define PCI_ENET0_MEMADDR	0xe0000000
-    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
-
-#endif	/* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI	1
-#endif
-
-#define CONFIG_MII		1	/* MII PHY management */
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-#define CONFIG_MPC85XX_FEC	1
-#define CONFIG_MPC85XX_FEC_NAME		"FEC"
-#define FEC_PHY_ADDR		3
-#define FEC_PHYIDX		0
-#define FEC_FLAGS		0
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#define CONFIG_HAS_ETH0
-#define	CONFIG_HAS_ETH1		1
-#define	CONFIG_HAS_ETH2		1
-
-#endif	/* CONFIG_TSEC_ENET */
-
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_IS_IN_FLASH	1
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x80000)
-  #define CONFIG_ENV_SECT_SIZE	0x40000 /* 256K(one sector) for env */
-  #define CONFIG_ENV_SIZE		0x2000
-#else
-  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
-  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-  #define CONFIG_ENV_SIZE		0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-    #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-    #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
-#define CONFIG_LOOPW
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR	 00:40:42:01:00:00
-#define CONFIG_ETH1ADDR	 00:40:42:01:00:01
-#define CONFIG_ETH2ADDR	 00:40:42:01:00:02
-#endif
-
-
-#define CONFIG_ROOTPATH		/opt/eldk/ppc_85xx
-#define CONFIG_BOOTFILE		pm854/uImage
-
-#define CONFIG_HOSTNAME		pm854
-#define CONFIG_IPADDR	 192.168.0.103
-#define CONFIG_SERVERIP	 192.168.0.64
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_NETMASK	 255.255.255.0
-
-#define CONFIG_LOADADDR	 200000 /* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 5	/* -1 disables auto-boot */
-#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 9600
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-   "netdev=eth0\0"							\
-   "consoledev=ttyS0\0"							\
-   "ramdiskaddr=400000\0"						\
-   "ramdiskfile=pm854/uRamdisk\0"
-
-#define CONFIG_NFSBOOTCOMMAND						\
-   "setenv bootargs root=/dev/nfs rw "					\
-      "nfsroot=$serverip:$rootpath "					\
-      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-      "console=$consoledev,$baudrate $othbootargs;"			\
-   "tftp $loadaddr $bootfile;"						\
-   "bootm $loadaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
-   "setenv bootargs root=/dev/ram rw "					\
-      "console=$consoledev,$baudrate $othbootargs;"			\
-   "tftp $ramdiskaddr $ramdiskfile;"					\
-   "tftp $loadaddr $bootfile;"						\
-   "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
deleted file mode 100644
index d3e8f41..0000000
--- a/include/configs/PM856.h
+++ /dev/null
@@ -1,429 +0,0 @@
-/*
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao at motorola.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * MicroSys PM856 board configuration file
- *
- * Please refer to doc/README.mpc85xx for more info.
- *
- * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
-#define CONFIG_MPC8560		1	/* MPC8560 specific */
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-#define CONFIG_PM856		1	/* PM856 board specific */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff80000
-
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
-/*
- * sysclk for MPC85xx
- *
- * Two valid values are:
- *    33000000
- *    66000000
- *
- * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here, so that is now the default.
- * The board, however, can run at 66MHz.  In any event, this value
- * must match the settings of some switches.  Details can be found
- * in the README.mpc85xxads.
- */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ	66000000
-#endif
-
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
-
-#define CONFIG_SYS_INIT_DBCR DBCR_IDM		/* Enable Debug Exceptions */
-
-#undef	CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
-
-/* DDR Setup */
-#define CONFIG_FSL_DDR1
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_SPD
-#define CONFIG_DDR_DLL                      /* possible DLL fix needed */
-#define CONFIG_DDR_ECC			    /* only for ECC DDR module */
-#define CONFIG_FSL_DMA			    /* use DMA to init DDR ECC  */
-
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x58	/* CTLR 0 DIMM 0 */
-
-/* Manually set up DDR parameters */
-#define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256 MB */
-#define CONFIG_SYS_DDR_CS0_BNDS	0x0000000f	/* 0-256MB */
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80000102
-#define CONFIG_SYS_DDR_TIMING_1	0x47444321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2008000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_MODE	0x00000062	/* DLL,normal,seq,4/2.5 */
-#define CONFIG_SYS_DDR_INTERVAL	0x045b0100	/* autocharge,no open page */
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	0		/* LBC SDRAM is 0 MB */
-
-#define CONFIG_SYS_FLASH_BASE		0xfe000000	/* start of FLASH 32M */
-#define CONFIG_SYS_BR0_PRELIM		0xfe001801	/* port size 32bit */
-
-#define CONFIG_SYS_OR0_PRELIM		0xfe006f67	/* 32MB Flash */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#undef CONFIG_CLOCKS_IN_MHZ
-
-
-/*
- * Local Bus Definitions
- */
-
-#define CONFIG_SYS_LBC_LCRR		0x00030004    /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg */
-#define CONFIG_SYS_LBC_LSRT		0x20000000    /* LB sdram refresh timer */
-#define CONFIG_SYS_LBC_MRTPR		0x20000000    /* LB refresh timer prescal*/
-
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)    /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)    /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_ON_SCC	/* define if console on SCC */
-#undef  CONFIG_CONS_NONE	/* define if console on something else */
-#define CONFIG_CONS_INDEX       1  /* which serial channel for console */
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * I2C
- */
-#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
-#define CONFIG_SYS_I2C_OFFSET		0x3000
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x58
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
-/* RapidIO MMU */
-#define CONFIG_SYS_RIO_MEM_BASE	0xc0000000	/* base address */
-#define CONFIG_SYS_RIO_MEM_PHYS	CONFIG_SYS_RIO_MEM_BASE
-#define CONFIG_SYS_RIO_MEM_SIZE	0x20000000	/* 128M */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE	0xe2000000
-#define CONFIG_SYS_PCI1_IO_PHYS	CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE	0x1000000	/* 16M */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
-    #define PCI_ENET0_IOADDR	0xe0000000
-    #define PCI_ENET0_MEMADDR	0xe0000000
-    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-
-#endif	/* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI	1
-#endif
-
-#define CONFIG_MII		1	/* MII PHY management */
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-#endif  /* CONFIG_TSEC_ENET */
-
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#define CONFIG_ETHER_ON_FCC	/* define if ether on FCC   */
-#undef  CONFIG_ETHER_NONE	/* define if ether on something else */
-
-
-/*
-   * - Rx-CLK is CLK15
-   * - Tx-CLK is CLK14
-   * - Select bus for bd/buffers
-   * - Full duplex
- */
-#define CONFIG_ETHER_ON_FCC3
-#define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-#define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
-#define CONFIG_SYS_CPMFCR_RAMTYPE	0
-#define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE)
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_IS_IN_FLASH	1
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x80000)
-  #define CONFIG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
-  #define CONFIG_ENV_SIZE		0x2000
-#else
-  #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
-  #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-  #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
-  #define CONFIG_ENV_SIZE		0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-    #undef CONFIG_CMD_SAVEENV
-    #undef CONFIG_CMD_LOADS
-#endif
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_SYS_LOAD_ADDR	0x1000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-    #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-    #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
-#define CONFIG_LOOPW
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR   00:40:42:01:00:00
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR  00:40:42:01:00:01
-#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR  00:40:42:01:00:02
-#endif
-
-
-#define CONFIG_ROOTPATH		/opt/eldk/ppc_85xx
-#define CONFIG_BOOTFILE		pm856/uImage
-
-#define CONFIG_HOSTNAME		pm856
-#define CONFIG_IPADDR    192.168.0.103
-#define CONFIG_SERVERIP  192.168.0.64
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_NETMASK   255.255.255.0
-
-#define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 5	/* -1 disables auto-boot */
-#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE	9600
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				        \
-   "netdev=eth0\0"                                                      \
-   "consoledev=ttyS0\0"                                                 \
-   "ramdiskaddr=400000\0"						\
-   "ramdiskfile=pm856/uRamdisk\0"
-
-#define CONFIG_NFSBOOTCOMMAND	                                        \
-   "setenv bootargs root=/dev/nfs rw "                                  \
-      "nfsroot=$serverip:$rootpath "                                    \
-      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $loadaddr $bootfile;"                                          \
-   "bootm $loadaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
-   "setenv bootargs root=/dev/ram rw "                                  \
-      "console=$consoledev,$baudrate $othbootargs;"                     \
-   "tftp $ramdiskaddr $ramdiskfile;"                                    \
-   "tftp $loadaddr $bootfile;"                                          \
-   "bootm $loadaddr $ramdiskaddr"
-
-#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */
-- 
1.7.2.3



More information about the U-Boot mailing list