[U-Boot] [PATCH v3 1/1] MX5:MX53: add initial support for MX53EVK board

Jason Liu r64343 at freescale.com
Thu Dec 23 11:36:49 CET 2010


Add initial support for MX53EVK board support.
FEC, SD/MMC, UART, I2C, have been support.

Signed-off-by: Jason Liu <r64343 at freescale.com>

---
Changes for v2:
-Address the comments from Stefano, Albert and Wolfgang,
        -remove the ivt.S file and use imximage.cfg instead,
        -remove the ivt link to u-boot
-Address the comments from Stefano,
        -Correct the copyright issue,
        -Use mxc_get_gpio() and mxc_set_gpio() accessors.
        -Get rid of system_rev,
        -use i2c enumeration value (0,1,..N) instead of BASE address,
        -use fsl_pmic i2c interface,
        -Add comments for why manage the pmic in a different way for TO2
        -Remove the comments from configs/mx53evk.h,
         - /*
         -  * Disabled for now due to build problems under Debian and a significant
         -  * increase in the final file size: 144260 vs. 109536 Bytes.
         -  */
-Address the comments from Wolfgang,
        -Move CONFIG_SYS_TEXT_BASE  to board config file,
        -Remove the comments from configs/mx53evk.h
         - /* size in bytes reserved for initial data */
         #define BOARD_LATE_INIT
        -Change the comments,  * Hardware drivers to * UART drivers
Changes for v3:
- put uart and fec iomux setting to board_early_init_f so that uart can print
  out the early information such as uboot banner and cpuinfo etc.
---
 MAINTAINERS                       |    3 +
 board/freescale/mx53evk/Makefile  |   48 +++++
 board/freescale/mx53evk/mx53evk.c |  398 +++++++++++++++++++++++++++++++++++++
 boards.cfg                        |    1 +
 include/configs/mx53evk.h         |  217 ++++++++++++++++++++
 5 files changed, 667 insertions(+), 0 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 0590ad9..c87ca56 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1085,6 +1085,9 @@ Peter Meerwald <devel at bct-electronic.com>
 
 	bct-brettl2	BF536
 
+Jason Liu <r64343 at freescale.com>
+
+	MX53evk         i.MX53
 #########################################################################
 # End of MAINTAINERS list						#
 #########################################################################
diff --git a/board/freescale/mx53evk/Makefile b/board/freescale/mx53evk/Makefile
new file mode 100755
index 0000000..6b820f4
--- /dev/null
+++ b/board/freescale/mx53evk/Makefile
@@ -0,0 +1,48 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
+#
+# (C) Copyright 2010 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= mx53evk.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
new file mode 100755
index 0000000..e8fe6b2
--- /dev/null
+++ b/board/freescale/mx53evk/mx53evk.c
@@ -0,0 +1,398 @@
+/*
+ * (C) Copyright 2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx5x_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/errno.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <fsl_pmic.h>
+#include <mxc_gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+u32 get_board_rev(void)
+{
+	return get_cpu_rev();
+}
+
+int dram_init(void)
+{
+	/* dram_init must store complete ramsize in gd->ram_size */
+	gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE,
+				PHYS_SDRAM_1_SIZE);
+	return 0;
+}
+
+static void setup_iomux_uart(void)
+{
+	/* UART1 RXD */
+	mxc_request_iomux(MX53_PIN_CSI0_D11, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX53_PIN_CSI0_D11,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+	mxc_iomux_set_input(MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x1);
+
+	/* UART1 TXD */
+	mxc_request_iomux(MX53_PIN_CSI0_D10, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX53_PIN_CSI0_D10,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+}
+
+#ifdef CONFIG_I2C_MXC
+static void setup_i2c(unsigned int port_number)
+{
+	switch (port_number) {
+	case 0:
+		/* i2c1 SDA */
+		mxc_request_iomux(MX53_PIN_CSI0_D8,
+				IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C1_IPP_SDA_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_CSI0_D8,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		/* i2c1 SCL */
+		mxc_request_iomux(MX53_PIN_CSI0_D9,
+				IOMUX_CONFIG_ALT5 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C1_IPP_SCL_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_CSI0_D9,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		break;
+	case 1:
+		/* i2c2 SDA */
+		mxc_request_iomux(MX53_PIN_KEY_ROW3,
+				IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C2_IPP_SDA_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_KEY_ROW3,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+
+		/* i2c2 SCL */
+		mxc_request_iomux(MX53_PIN_KEY_COL3,
+				IOMUX_CONFIG_ALT4 | IOMUX_CONFIG_SION);
+		mxc_iomux_set_input(MX53_I2C2_IPP_SCL_IN_SELECT_INPUT,
+				INPUT_CTL_PATH0);
+		mxc_iomux_set_pad(MX53_PIN_KEY_COL3,
+				PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH |
+				PAD_CTL_100K_PU | PAD_CTL_HYS_ENABLE |
+				PAD_CTL_ODE_OPENDRAIN_ENABLE);
+		break;
+	default:
+		printf("Warning: Wrong I2C port number\n");
+		break;
+	}
+}
+
+void power_init(void)
+{
+	unsigned int val;
+
+	/* Set VDDA to 1.25V */
+	val = pmic_reg_read(REG_SW_2);
+	val = (val & (~0x1F)) | 0x1A;
+	pmic_reg_write(REG_SW_2, val);
+
+	/*
+	 * Need increase VCC and VDDA to 1.3V
+	 * according to MX53 IC TO2 datasheet.
+	 */
+	if (is_soc_rev(CHIP_REV_2_0) == 0) {
+		/* Set VCC to 1.3V for TO2 */
+		val = pmic_reg_read(REG_SW_1);
+		val = (val & (~0x1F)) | 0x1C;
+		pmic_reg_write(REG_SW_2, val);
+
+		/* Set VDDA to 1.3V for TO2 */
+		val = pmic_reg_read(REG_SW_2);
+		val = (val & (~0x1F)) | 0x1C;
+		pmic_reg_write(REG_SW_2, val);
+	}
+}
+#endif
+
+static void setup_iomux_fec(void)
+{
+	/*FEC_MDIO*/
+	mxc_request_iomux(MX53_PIN_FEC_MDIO, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_MDIO,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_22K_PU | PAD_CTL_ODE_OPENDRAIN_ENABLE);
+	mxc_iomux_set_input(MX53_FEC_FEC_MDI_SELECT_INPUT, 0x1);
+
+	/*FEC_MDC*/
+	mxc_request_iomux(MX53_PIN_FEC_MDC, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_MDC, PAD_CTL_DRV_HIGH);
+
+	/* FEC RXD1 */
+	mxc_request_iomux(MX53_PIN_FEC_RXD1, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RXD1,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC RXD0 */
+	mxc_request_iomux(MX53_PIN_FEC_RXD0, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RXD0,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	 /* FEC TXD1 */
+	mxc_request_iomux(MX53_PIN_FEC_TXD1, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TXD1, PAD_CTL_DRV_HIGH);
+
+	/* FEC TXD0 */
+	mxc_request_iomux(MX53_PIN_FEC_TXD0, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TXD0, PAD_CTL_DRV_HIGH);
+
+	/* FEC TX_EN */
+	mxc_request_iomux(MX53_PIN_FEC_TX_EN, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_TX_EN, PAD_CTL_DRV_HIGH);
+
+	/* FEC TX_CLK */
+	mxc_request_iomux(MX53_PIN_FEC_REF_CLK, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_REF_CLK,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC RX_ER */
+	mxc_request_iomux(MX53_PIN_FEC_RX_ER, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_RX_ER,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+
+	/* FEC CRS */
+	mxc_request_iomux(MX53_PIN_FEC_CRS_DV, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX53_PIN_FEC_CRS_DV,
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE);
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+	{MMC_SDHC1_BASE_ADDR, 1},
+	{MMC_SDHC3_BASE_ADDR, 1},
+};
+
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
+		*cd = mxc_gpio_get(77); /*GPIO3_13*/
+	else
+		*cd = mxc_gpio_get(75); /*GPIO3_11*/
+
+	return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	u32 index;
+	s32 status = 0;
+
+	for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+		switch (index) {
+		case 0:
+			mxc_request_iomux(MX53_PIN_SD1_CMD, IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_CLK, IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA0,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA1,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA2,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_SD1_DATA3,
+						IOMUX_CONFIG_ALT0);
+			mxc_request_iomux(MX53_PIN_EIM_DA13,
+						IOMUX_CONFIG_ALT1);
+
+			mxc_iomux_set_pad(MX53_PIN_SD1_CMD,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_CLK,
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU |
+				PAD_CTL_DRV_HIGH);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA0,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA1,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA2,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_SD1_DATA3,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			break;
+		case 1:
+			mxc_request_iomux(MX53_PIN_ATA_RESET_B,
+						IOMUX_CONFIG_ALT2);
+			mxc_request_iomux(MX53_PIN_ATA_IORDY,
+						IOMUX_CONFIG_ALT2);
+			mxc_request_iomux(MX53_PIN_ATA_DATA8,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA9,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA10,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA11,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA0,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA1,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA2,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_ATA_DATA3,
+						IOMUX_CONFIG_ALT4);
+			mxc_request_iomux(MX53_PIN_EIM_DA11,
+						IOMUX_CONFIG_ALT1);
+
+			mxc_iomux_set_pad(MX53_PIN_ATA_RESET_B,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_100K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_IORDY,
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU |
+				PAD_CTL_DRV_HIGH);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA8,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA9,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA10,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA11,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA0,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA1,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA2,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+			mxc_iomux_set_pad(MX53_PIN_ATA_DATA3,
+				PAD_CTL_HYS_ENABLE | PAD_CTL_DRV_HIGH |
+				PAD_CTL_PUE_PULL | PAD_CTL_PKE_ENABLE |
+				PAD_CTL_HYS_ENABLE | PAD_CTL_47K_PU);
+
+			break;
+		default:
+			printf("Warning: you configured more ESDHC controller"
+				"(%d) as supported by the board(2)\n",
+				CONFIG_SYS_FSL_ESDHC_NUM);
+			return status;
+		}
+		status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+	}
+
+	return status;
+}
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_fec();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_arch_number = MACH_TYPE_MX53_EVK;
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_I2C_MXC
+	setup_i2c(1);
+	power_init();
+#endif
+	return 0;
+}
+#endif
+
+int checkboard(void)
+{
+	u32 cause;
+	struct src *src_regs = (struct src *)SRC_BASE_ADDR;
+
+	puts("Board: MX53EVK [");
+
+	cause = src_regs->srsr;
+	switch (cause) {
+	case 0x0001:
+		printf("POR");
+		break;
+	case 0x0009:
+		printf("RST");
+		break;
+	case 0x0010:
+	case 0x0011:
+		printf("WDOG");
+		break;
+	default:
+		printf("unknown");
+	}
+	printf("]\n");
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index dcd5a12..736e88e 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -101,6 +101,7 @@ omap5912osk                  arm         arm926ejs   -                   ti
 edminiv2                     arm         arm926ejs   -                   LaCie          orion5x
 ca9x4_ct_vxp                 arm         armv7       vexpress            armltd
 mx51evk                      arm         armv7       mx51evk             freescale      mx5
+mx53evk                      arm         armv7       mx53evk             freescale      mx5
 vision2                      arm         armv7       vision2             ttcontrol      mx5
 omap3_overo                  arm         armv7       overo               -              omap3
 omap3_pandora                arm         armv7       pandora             -              omap3
diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h
new file mode 100755
index 0000000..d6cf04e
--- /dev/null
+++ b/include/configs/mx53evk.h
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the MX53-EVK Freescale board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+ /* High Level Configuration Options */
+
+#define CONFIG_MX53
+
+#define CONFIG_SYS_MX5_HCLK	24000000
+#define CONFIG_SYS_MX5_CLK32		32768
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_L2_OFF
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
+#define CONFIG_REVISION_TAG		1
+#define CONFIG_SETUP_MEMORY_TAGS	1
+#define CONFIG_INITRD_TAG		1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_SYS_MX53_UART1
+
+/*
+ * I2C Configs
+ */
+#define CONFIG_CMD_I2C          1
+#define CONFIG_HARD_I2C         1
+#define CONFIG_I2C_MXC          1
+#define CONFIG_SYS_I2C_MX53_PORT2       1
+#define CONFIG_SYS_I2C_SPEED            100000
+#define CONFIG_SYS_I2C_SLAVE            0xfe
+
+/*
+ * PMIC Configs
+ */
+#define CONFIG_FSL_PMIC
+#define CONFIG_FSL_PMIC_I2C
+#define CONFIG_SYS_FSL_PMIC_I2C_ADDR    8
+
+/*
+ * MMC Configs
+ */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_ESDHC_NUM	2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Eth Configs
+ */
+#define CONFIG_HAS_ETH1
+#define CONFIG_NET_MULTI
+#define CONFIG_MII
+#define CONFIG_DISCOVER_PHY
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE	FEC_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR	0x1F
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}
+
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY	3
+
+#define CONFIG_PRIME	"FEC0"
+
+#define CONFIG_LOADADDR		0x70800000	/* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE    0x77800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=boot.scr\0" \
+	"uimage=uImage\0" \
+	"mmcdev=0\0" \
+	"mmcpart=2\0" \
+	"mmcroot=/dev/mmcblk0p3 rw\0" \
+	"mmcrootfstype=ext3 rootwait\0" \
+	"mmcargs=setenv bootargs console=ttymxc0,${baudrate} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0" \
+	"loadbootscript=" \
+		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm\0" \
+	"netargs=setenv bootargs console=ttymxc0,${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc rescan ${mmcdev}; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loaduimage; then " \
+				"run mmcboot; " \
+			"else run netboot; " \
+			"fi; " \
+		"fi; " \
+	"else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT	200UL
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"MX53EVK U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START       0x70000000
+#define CONFIG_SYS_MEMTEST_END         0x10000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_SYS_HZ		1000
+#define CONFIG_CMDLINE_EDITING
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128 * 1024)	/* regular stack */
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+#define PHYS_SDRAM_1		CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE	(512 * 1024 * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE        (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#endif				/* __CONFIG_H */
-- 
1.7.0.4




More information about the U-Boot mailing list