[U-Boot] [PATCH V3 7/8] fec_mxc: add MX25 support

Ben Warren biggerbadderben at gmail.com
Mon Feb 1 07:18:52 CET 2010


Tom,

As with the other one, I can't apply this by itself.  Please apply to 
your tree.

John Rigby wrote:
> Use RMII for MX25
> Add code to init gasket that enables RMII
>
> Signed-off-by: John Rigby <jcrigby at gmail.com>
>   
Acked-by: Ben Warren <biggerbadderben at gmail.com>
> ---
>  drivers/net/fec_mxc.c             |   31 ++++++++++++++++++++++++++++++-
>  drivers/net/fec_mxc.h             |   32 ++++++++++++++++++++++++++++++--
>  include/asm-arm/arch-mx25/clock.h |    1 +
>  3 files changed, 61 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index b5619eb..f109485 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -347,6 +347,34 @@ static int fec_open(struct eth_device *edev)
>  	 */
>  	writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
>  		&fec->eth->ecntrl);
> +#ifdef CONFIG_MX25
> +	udelay(100);
> +	/*
> +	 * setup the MII gasket for RMII mode
> +	 */
> +
> +	/* disable the gasket */
> +	writew(0, &fec->eth->miigsk_enr);
> +
> +	/* wait for the gasket to be disabled */
> +	while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY)
> +		udelay(2);
> +
> +	/* configure gasket for RMII, 50 MHz, no loopback, and no echo */
> +	writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr);
> +
> +	/* re-enable the gasket */
> +	writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr);
> +
> +	/* wait until MII gasket is ready */
> +	int max_loops = 10;
> +	while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) {
> +		if (--max_loops <= 0) {
> +			printf("WAIT for MII Gasket ready timed out\n");
> +			break;
> +		}
> +	}
> +#endif
>  
>  	miiphy_wait_aneg(edev);
>  	miiphy_speed(edev->name, CONFIG_FEC_MXC_PHYADDR);
> @@ -498,7 +526,8 @@ static void fec_halt(struct eth_device *dev)
>  	 * Disable the Ethernet Controller
>  	 * Note: this will also reset the BD index counter!
>  	 */
> -	writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl);
> +	writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN,
> +			&fec->eth->ecntrl);
>  	fec->rbd_index = 0;
>  	fec->tbd_index = 0;
>  	debug("eth_halt: done\n");
> diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
> index 6cb1bfc..5d0d69d 100644
> --- a/drivers/net/fec_mxc.h
> +++ b/drivers/net/fec_mxc.h
> @@ -145,9 +145,17 @@ struct ethernet_regs {
>  	uint32_t r_fdxfc;		/* MBAR_ETH + 0x2DC */
>  	uint32_t ieee_r_octets_ok;	/* MBAR_ETH + 0x2E0 */
>  
> -	uint32_t res14[6];		/* MBAR_ETH + 0x2E4-2FC */
> -
> +	uint32_t res14[7];		/* MBAR_ETH + 0x2E4-2FC */
> +
> +#ifdef CONFIG_MX25
> +	uint16_t miigsk_cfgr;		/* MBAR_ETH + 0x300 */
> +	uint16_t res15[3];		/* MBAR_ETH + 0x302-306 */
> +	uint16_t miigsk_enr;		/* MBAR_ETH + 0x308 */
> +	uint16_t res16[3];		/* MBAR_ETH + 0x30a-30e */
> +	uint32_t res17[60];		/* MBAR_ETH + 0x300-3FF */
> +#else
>  	uint32_t res15[64];		/* MBAR_ETH + 0x300-3FF */
> +#endif
>  };
>  
>  #define FEC_IEVENT_HBERR		0x80000000
> @@ -196,6 +204,26 @@ struct ethernet_regs {
>  #define FEC_ECNTRL_RESET		0x00000001	/* reset the FEC */
>  #define FEC_ECNTRL_ETHER_EN		0x00000002	/* enable the FEC */
>  
> +#ifdef CONFIG_MX25
> +/* defines for MIIGSK */
> +/* RMII frequency control: 0=50MHz, 1=5MHz */
> +#define MIIGSK_CFGR_FRCONT		(1 << 6)
> +/* loopback mode */
> +#define MIIGSK_CFGR_LBMODE		(1 << 4)
> +/* echo mode */
> +#define MIIGSK_CFGR_EMODE		(1 << 3)
> +/* MII gasket mode field */
> +#define MIIGSK_CFGR_IF_MODE_MASK	(3 << 0)
> +/* MMI/7-Wire mode */
> +#define MIIGSK_CFGR_IF_MODE_MII		(0 << 0)
> +/* RMII mode */
> +#define MIIGSK_CFGR_IF_MODE_RMII	(1 << 0)
> +/* reflects MIIGSK Enable bit (RO) */
> +#define MIIGSK_ENR_READY		(1 << 2)
> +/* enable MIGSK (set by default) */
> +#define MIIGSK_ENR_EN			(1 << 1)
> +#endif
> +
>  /**
>   * @brief Descriptor buffer alignment
>   *
> diff --git a/include/asm-arm/arch-mx25/clock.h b/include/asm-arm/arch-mx25/clock.h
> index b0752e7..c59f588 100644
> --- a/include/asm-arm/arch-mx25/clock.h
> +++ b/include/asm-arm/arch-mx25/clock.h
> @@ -30,6 +30,7 @@ ulong imx_get_perclk(int clk);
>  ulong imx_get_ahbclk(void);
>  
>  #define imx_get_uartclk() imx_get_perclk(15)
> +#define imx_get_fecclk() (imx_get_ahbclk()/2)
>  
>  
>  #endif /* __ASM_ARCH_CLOCK_H */
>   
regards,
Ben


More information about the U-Boot mailing list