[U-Boot] AVR32 AP700x - I2C somewhere?

[Andreas Bießmann]

Am 01.06.2010 16:04, schrieb Reinhard Meyer (-VC):
> Hi,
Dear Reinhard Meyer,

> has anyone started or completed work on an I2C driver for AP7000x?
No ...
> 
> If not, I am at least going to make SOFT I2C defines to read VPD from an 
> At24C64 EEPROM.
But I've working soft-i2c here. There are still some other examples in
u-boot how to interface a at24xx eeprom.

custom board config file:
---8<---
/* i2c definitions */
#define CONFIG_SOFT_I2C
#if defined(CONFIG_SOFT_I2C)
#define DEBUG_I2C
#ifndef __ASSEMBLY__
#include <asm/arch/portmux.h>
#define MEDUCORE_SDA_PIN	6
#define MEDUCORE_SCL_PIN	7

#define I2C_ACTIVE	portmux_select_gpio(PORTMUX_PORT_A,
(1<<MEDUCORE_SDA_PIN), PORTMUX_DIR_OUTPUT|PORTMUX_INIT_LOW)
#define I2C_TRISTATE		portmux_select_gpio(PORTMUX_PORT_A,
(1<<MEDUCORE_SDA_PIN), PORTMUX_DIR_INPUT|PORTMUX_OPEN_DRAIN)
#define I2C_READ	pio_get_input_value(GPIO_PIN_PA(MEDUCORE_SDA_PIN))
#define I2C_SDA(bit)	pio_set_output_value(GPIO_PIN_PA(MEDUCORE_SDA_PIN),
bit)
#define I2C_SCL(bit)	pio_set_output_value(GPIO_PIN_PA(MEDUCORE_SCL_PIN),
bit)
#endif

#define I2C_DELAY	udelay(3)	/* TODO needs testing */
#define I2C_SOFT_DECLARATIONS

#define	CONFIG_SYS_I2C_SLAVE		0x0
#define	CONFIG_SYS_I2C_SPEED		100000 /* TODO needs testing */
#define CONFIG_CMD_I2C

#endif
--->8---

and in our custom board implementation (only snippet):
---8<---
@@ -29,6 +29,8 @@
 #include <asm/arch/hmatrix.h>
 #include <asm/arch/portmux.h>

+#include <i2c.h>
+
 DECLARE_GLOBAL_DATA_PTR;

 /*
@@ -71,6 +73,38 @@ static const struct sdram_config sdram_config = {

 int board_early_init_f(void)
 {
+       unsigned char val = 0xFF;
+       unsigned char version = 0x00;
+       int ret = -1; // assume error
+
+       // first select SCL gpio
+       portmux_select_gpio(PORTMUX_PORT_A, (1<<MEDUCORE_SCL_PIN),
PORTMUX_DIR_OUTPUT|PORTMUX_INIT_LOW);
+       // initialize i2c
+       i2c_init(1000, 0x27);
+       // check for precedence of port multiplexer
+       ret = i2c_probe(0x27);
+       if ( ret != 0 ) {
+               gd->flags |= GD_FLG_POSTFAIL;
+               goto out;
+       }
+
+       ret |= i2c_write(0x27, 0x06, 1, &val, 1); // set GPPU to FF
+       ret |= i2c_write(0x27, 0x01, 1, &val, 1); // set IPOL to FF
(invert palaritiy)
+       if ( ret != 0 ) {
+               gd->flags |= GD_FLG_POSTFAIL;
+               goto out;
+       }
+
+       ret = i2c_read(0x27, 0x09, 1, &version, 1); // read in the
version value
+       if ( ret != 0 ) {
+               gd->flags |= GD_FLG_POSTFAIL;
+               goto out;
+       }
+       // version can be used from here

--->8---

regards

Andreas Bießmann