[U-Boot] [PATCH V3 03/10] 83xx/85xx/86xx: LBC register cleanup
Becky Bruce
beckyb at kernel.crashing.org
Wed Jun 2 22:55:44 CEST 2010
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb at kernel.crashing.org>
---
Makefile | 1 +
arch/powerpc/cpu/mpc83xx/cpu.c | 12 ++--
arch/powerpc/cpu/mpc83xx/cpu_init.c | 53 ++----------
arch/powerpc/cpu/mpc83xx/nand_init.c | 4 +-
arch/powerpc/cpu/mpc83xx/speed.c | 2 +-
arch/powerpc/cpu/mpc85xx/cpu.c | 12 +--
arch/powerpc/cpu/mpc85xx/cpu_init.c | 58 +------------
arch/powerpc/cpu/mpc85xx/cpu_init_nand.c | 6 +-
arch/powerpc/cpu/mpc85xx/speed.c | 5 +-
arch/powerpc/cpu/mpc86xx/cpu.c | 15 +---
arch/powerpc/cpu/mpc86xx/cpu_init.c | 55 +------------
arch/powerpc/cpu/mpc86xx/speed.c | 5 +-
arch/powerpc/cpu/mpc8xxx/Makefile | 3 +
arch/powerpc/cpu/mpc8xxx/fsl_lbc.c | 84 ++++++++++++++++++
arch/powerpc/include/asm/config.h | 6 ++
arch/powerpc/include/asm/fsl_lbc.h | 109 ++++++++++++++----------
arch/powerpc/include/asm/immap_83xx.h | 13 ++--
arch/powerpc/include/asm/immap_85xx.h | 46 +----------
arch/powerpc/include/asm/immap_86xx.h | 49 +----------
board/atum8548/atum8548.c | 2 +-
board/esd/vme8349/vme8349.c | 2 +-
board/freescale/mpc8313erdb/sdram.c | 2 +-
board/freescale/mpc8349emds/mpc8349emds.c | 2 +-
board/freescale/mpc8349itx/mpc8349itx.c | 7 +-
board/freescale/mpc8360emds/mpc8360emds.c | 6 +-
board/freescale/mpc8360erdk/nand.c | 6 +-
board/freescale/mpc8540ads/mpc8540ads.c | 8 +-
board/freescale/mpc8541cds/mpc8541cds.c | 13 +--
board/freescale/mpc8544ds/mpc8544ds.c | 2 +-
board/freescale/mpc8548cds/mpc8548cds.c | 13 +--
board/freescale/mpc8555cds/mpc8555cds.c | 12 +--
board/freescale/mpc8560ads/mpc8560ads.c | 8 +-
board/freescale/mpc8568mds/mpc8568mds.c | 11 +--
board/freescale/mpc8569mds/mpc8569mds.c | 2 +-
board/mpc8540eval/mpc8540eval.c | 6 +-
board/pm854/pm854.c | 2 +-
board/pm856/pm856.c | 2 +-
board/sbc8349/sbc8349.c | 2 +-
board/sbc8548/sbc8548.c | 20 ++---
board/sbc8560/sbc8560.c | 6 +-
board/sheldon/simpc8313/sdram.c | 2 +-
board/sheldon/simpc8313/simpc8313.c | 2 +-
board/socrates/socrates.c | 31 +++----
board/tqc/tqm834x/tqm834x.c | 8 +-
board/tqc/tqm85xx/nand.c | 12 ++--
board/tqc/tqm85xx/tqm85xx.c | 35 ++++----
board/xes/xpedite5170/xpedite5170.c | 10 +--
board/xes/xpedite5200/xpedite5200.c | 11 +--
board/xes/xpedite5370/xpedite5370.c | 9 +-
drivers/mtd/nand/fsl_elbc_nand.c | 18 ++---
include/mpc85xx.h | 2 -
nand_spl/board/freescale/mpc8536ds/nand_boot.c | 5 +-
nand_spl/nand_boot_fsl_elbc.c | 4 +-
53 files changed, 321 insertions(+), 500 deletions(-)
create mode 100644 arch/powerpc/cpu/mpc8xxx/fsl_lbc.c
diff --git a/Makefile b/Makefile
index c26e491..2d4327a 100644
--- a/Makefile
+++ b/Makefile
@@ -220,6 +220,7 @@ LIBS += drivers/power/libpower.a
LIBS += drivers/spi/libspi.a
ifeq ($(CPU),mpc83xx)
LIBS += drivers/qe/qe.a
+LIBS += arch/powerpc/cpu/mpc8xxx/lib8xxx.a
endif
ifeq ($(CPU),mpc85xx)
LIBS += drivers/qe/qe.a
diff --git a/arch/powerpc/cpu/mpc83xx/cpu.c b/arch/powerpc/cpu/mpc83xx/cpu.c
index d3be909..24193ce 100644
--- a/arch/powerpc/cpu/mpc83xx/cpu.c
+++ b/arch/powerpc/cpu/mpc83xx/cpu.c
@@ -156,16 +156,16 @@ int checkcpu(void)
void upmconfig (uint upm, uint *table, uint size)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbus = &immap->lbus;
+ volatile fsl_lbc_t *lbc = &immap->im_lbc;
volatile uchar *dummy = NULL;
const u32 msel = (upm + 4) << BR_MSEL_SHIFT; /* What the MSEL field in BRn should be */
- volatile u32 *mxmr = &lbus->mamr + upm; /* Pointer to mamr, mbmr, or mcmr */
+ volatile u32 *mxmr = &lbc->mamr + upm; /* ptr to mamr, mbmr, or mcmr */
uint i;
- /* Scan all the banks to determine the base address of the device */
+ /* Find the address for the dummy write transaction */
for (i = 0; i < 8; i++) {
- if ((lbus->bank[i].br & BR_MSEL) == msel) {
- dummy = (uchar *) (lbus->bank[i].br & BR_BA);
+ if ((get_lbc_br(i) & BR_MSEL) == msel) {
+ dummy = (uchar *) (get_lbc_br(i) & BR_BA);
break;
}
}
@@ -179,7 +179,7 @@ void upmconfig (uint upm, uint *table, uint size)
*mxmr = (*mxmr & 0xCFFFFFC0) | 0x10000000;
for (i = 0; i < size; i++) {
- lbus->mdr = table[i];
+ lbc->mdr = table[i];
__asm__ __volatile__ ("sync");
*dummy = 0; /* Write the value to memory and increment MAD */
__asm__ __volatile__ ("sync");
diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c b/arch/powerpc/cpu/mpc83xx/cpu_init.c
index f3b67ae..83cba93 100644
--- a/arch/powerpc/cpu/mpc83xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c
@@ -236,8 +236,8 @@ void cpu_init_f (volatile immap_t * im)
/* LCRR - Clock Ratio Register (10.3.1.16)
* write, read, and isync per MPC8379ERM rev.1 CLKDEV field description
*/
- clrsetbits_be32(&im->lbus.lcrr, lcrr_mask, lcrr_val);
- __raw_readl(&im->lbus.lcrr);
+ clrsetbits_be32(&im->im_lbc.lcrr, lcrr_mask, lcrr_val);
+ __raw_readl(&im->im_lbc.lcrr);
isync();
/* Enable Time Base & Decrementer ( so we will have udelay() )*/
@@ -267,80 +267,41 @@ void cpu_init_f (volatile immap_t * im)
/* Config QE ioports */
config_qe_ioports();
#endif
+ /* Set up preliminary BR/OR regs */
+ init_early_memctl_regs();
- /*
- * Memory Controller:
- */
-
- /* Map banks 0 and 1 to the FLASH banks 0 and 1 at preliminary
- * addresses - these have to be modified later when FLASH size
- * has been determined
- */
-
-#if defined(CONFIG_SYS_BR0_PRELIM) \
- && defined(CONFIG_SYS_OR0_PRELIM) \
- && defined(CONFIG_SYS_LBLAWBAR0_PRELIM) \
- && defined(CONFIG_SYS_LBLAWAR0_PRELIM)
- im->lbus.bank[0].br = CONFIG_SYS_BR0_PRELIM;
- im->lbus.bank[0].or = CONFIG_SYS_OR0_PRELIM;
+ /* Local Access window setup */
+#if defined(CONFIG_SYS_LBLAWBAR0_PRELIM) && defined(CONFIG_SYS_LBLAWAR0_PRELIM)
im->sysconf.lblaw[0].bar = CONFIG_SYS_LBLAWBAR0_PRELIM;
im->sysconf.lblaw[0].ar = CONFIG_SYS_LBLAWAR0_PRELIM;
#else
-#error CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_LBLAWBAR0_PRELIM & CONFIG_SYS_LBLAWAR0_PRELIM must be defined
+#error CONFIG_SYS_LBLAWBAR0_PRELIM & CONFIG_SYS_LBLAWAR0_PRELIM must be defined
#endif
-#if defined(CONFIG_SYS_BR1_PRELIM) && defined(CONFIG_SYS_OR1_PRELIM)
- im->lbus.bank[1].br = CONFIG_SYS_BR1_PRELIM;
- im->lbus.bank[1].or = CONFIG_SYS_OR1_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR1_PRELIM) && defined(CONFIG_SYS_LBLAWAR1_PRELIM)
im->sysconf.lblaw[1].bar = CONFIG_SYS_LBLAWBAR1_PRELIM;
im->sysconf.lblaw[1].ar = CONFIG_SYS_LBLAWAR1_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR2_PRELIM) && defined(CONFIG_SYS_OR2_PRELIM)
- im->lbus.bank[2].br = CONFIG_SYS_BR2_PRELIM;
- im->lbus.bank[2].or = CONFIG_SYS_OR2_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR2_PRELIM) && defined(CONFIG_SYS_LBLAWAR2_PRELIM)
im->sysconf.lblaw[2].bar = CONFIG_SYS_LBLAWBAR2_PRELIM;
im->sysconf.lblaw[2].ar = CONFIG_SYS_LBLAWAR2_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR3_PRELIM) && defined(CONFIG_SYS_OR3_PRELIM)
- im->lbus.bank[3].br = CONFIG_SYS_BR3_PRELIM;
- im->lbus.bank[3].or = CONFIG_SYS_OR3_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR3_PRELIM) && defined(CONFIG_SYS_LBLAWAR3_PRELIM)
im->sysconf.lblaw[3].bar = CONFIG_SYS_LBLAWBAR3_PRELIM;
im->sysconf.lblaw[3].ar = CONFIG_SYS_LBLAWAR3_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR4_PRELIM) && defined(CONFIG_SYS_OR4_PRELIM)
- im->lbus.bank[4].br = CONFIG_SYS_BR4_PRELIM;
- im->lbus.bank[4].or = CONFIG_SYS_OR4_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR4_PRELIM) && defined(CONFIG_SYS_LBLAWAR4_PRELIM)
im->sysconf.lblaw[4].bar = CONFIG_SYS_LBLAWBAR4_PRELIM;
im->sysconf.lblaw[4].ar = CONFIG_SYS_LBLAWAR4_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR5_PRELIM) && defined(CONFIG_SYS_OR5_PRELIM)
- im->lbus.bank[5].br = CONFIG_SYS_BR5_PRELIM;
- im->lbus.bank[5].or = CONFIG_SYS_OR5_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR5_PRELIM) && defined(CONFIG_SYS_LBLAWAR5_PRELIM)
im->sysconf.lblaw[5].bar = CONFIG_SYS_LBLAWBAR5_PRELIM;
im->sysconf.lblaw[5].ar = CONFIG_SYS_LBLAWAR5_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR6_PRELIM) && defined(CONFIG_SYS_OR6_PRELIM)
- im->lbus.bank[6].br = CONFIG_SYS_BR6_PRELIM;
- im->lbus.bank[6].or = CONFIG_SYS_OR6_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR6_PRELIM) && defined(CONFIG_SYS_LBLAWAR6_PRELIM)
im->sysconf.lblaw[6].bar = CONFIG_SYS_LBLAWBAR6_PRELIM;
im->sysconf.lblaw[6].ar = CONFIG_SYS_LBLAWAR6_PRELIM;
#endif
-#if defined(CONFIG_SYS_BR7_PRELIM) && defined(CONFIG_SYS_OR7_PRELIM)
- im->lbus.bank[7].br = CONFIG_SYS_BR7_PRELIM;
- im->lbus.bank[7].or = CONFIG_SYS_OR7_PRELIM;
-#endif
#if defined(CONFIG_SYS_LBLAWBAR7_PRELIM) && defined(CONFIG_SYS_LBLAWAR7_PRELIM)
im->sysconf.lblaw[7].bar = CONFIG_SYS_LBLAWBAR7_PRELIM;
im->sysconf.lblaw[7].ar = CONFIG_SYS_LBLAWAR7_PRELIM;
diff --git a/arch/powerpc/cpu/mpc83xx/nand_init.c b/arch/powerpc/cpu/mpc83xx/nand_init.c
index 38e141a..d1648b7 100644
--- a/arch/powerpc/cpu/mpc83xx/nand_init.c
+++ b/arch/powerpc/cpu/mpc83xx/nand_init.c
@@ -88,8 +88,8 @@ void cpu_init_f (volatile immap_t * im)
&& defined(CONFIG_SYS_NAND_OR_PRELIM) \
&& defined(CONFIG_SYS_NAND_LBLAWBAR_PRELIM) \
&& defined(CONFIG_SYS_NAND_LBLAWAR_PRELIM)
- im->lbus.bank[0].br = CONFIG_SYS_NAND_BR_PRELIM;
- im->lbus.bank[0].or = CONFIG_SYS_NAND_OR_PRELIM;
+ set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
im->sysconf.lblaw[0].bar = CONFIG_SYS_NAND_LBLAWBAR_PRELIM;
im->sysconf.lblaw[0].ar = CONFIG_SYS_NAND_LBLAWAR_PRELIM;
#else
diff --git a/arch/powerpc/cpu/mpc83xx/speed.c b/arch/powerpc/cpu/mpc83xx/speed.c
index 500eef1..a42c495 100644
--- a/arch/powerpc/cpu/mpc83xx/speed.c
+++ b/arch/powerpc/cpu/mpc83xx/speed.c
@@ -388,7 +388,7 @@ int get_clocks(void)
lbiu_clk = csb_clk *
(1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT));
- lcrr = (im->lbus.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT;
+ lcrr = (im->im_lbc.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT;
switch (lcrr) {
case 2:
case 4:
diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c
index fddeb2f..4160b60 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu.c
@@ -257,8 +257,7 @@ void upmconfig (uint upm, uint * table, uint size)
{
int i, mdr, mad, old_mad = 0;
volatile u32 *mxmr;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
- volatile u32 *brp,*orp;
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile u8* dummy = NULL;
int upmmask;
@@ -281,12 +280,9 @@ void upmconfig (uint upm, uint * table, uint size)
}
/* Find the address for the dummy write transaction */
- for (brp = &lbc->br0, orp = &lbc->or0, i = 0; i < 8;
- i++, brp += 2, orp += 2) {
-
- /* Look for a valid BR with selected UPM */
- if ((in_be32(brp) & (BR_V | BR_MSEL)) == (BR_V | upmmask)) {
- dummy = (volatile u8*)(in_be32(brp) & BR_BA);
+ for (i = 0; i < 8; i++) {
+ if ((get_lbc_br(i) & (BR_V | BR_MSEL)) == (BR_V | upmmask)) {
+ dummy = (volatile u8 *)(get_lbc_br(i) & BR_BA);
break;
}
}
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c
index 99431dc..d491e2a 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c
@@ -154,7 +154,6 @@ static void corenet_tb_init(void)
void cpu_init_f (void)
{
- volatile ccsr_lbc_t *memctl = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
extern void m8560_cpm_reset (void);
#ifdef CONFIG_MPC8548
ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
@@ -177,60 +176,7 @@ void cpu_init_f (void)
config_8560_ioports((ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR);
#endif
- /* Map banks 0 and 1 to the FLASH banks 0 and 1 at preliminary
- * addresses - these have to be modified later when FLASH size
- * has been determined
- */
-#if defined(CONFIG_SYS_OR0_REMAP)
- out_be32(&memctl->or0, CONFIG_SYS_OR0_REMAP);
-#endif
-#if defined(CONFIG_SYS_OR1_REMAP)
- out_be32(&memctl->or1, CONFIG_SYS_OR1_REMAP);
-#endif
-
- /* now restrict to preliminary range */
- /* if cs1 is already set via debugger, leave cs0/cs1 alone */
- if (! memctl->br1 & 1) {
-#if defined(CONFIG_SYS_BR0_PRELIM) && defined(CONFIG_SYS_OR0_PRELIM)
- out_be32(&memctl->br0, CONFIG_SYS_BR0_PRELIM);
- out_be32(&memctl->or0, CONFIG_SYS_OR0_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR1_PRELIM) && defined(CONFIG_SYS_OR1_PRELIM)
- out_be32(&memctl->or1, CONFIG_SYS_OR1_PRELIM);
- out_be32(&memctl->br1, CONFIG_SYS_BR1_PRELIM);
-#endif
- }
-
-#if defined(CONFIG_SYS_BR2_PRELIM) && defined(CONFIG_SYS_OR2_PRELIM)
- out_be32(&memctl->or2, CONFIG_SYS_OR2_PRELIM);
- out_be32(&memctl->br2, CONFIG_SYS_BR2_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR3_PRELIM) && defined(CONFIG_SYS_OR3_PRELIM)
- out_be32(&memctl->or3, CONFIG_SYS_OR3_PRELIM);
- out_be32(&memctl->br3, CONFIG_SYS_BR3_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR4_PRELIM) && defined(CONFIG_SYS_OR4_PRELIM)
- out_be32(&memctl->or4, CONFIG_SYS_OR4_PRELIM);
- out_be32(&memctl->br4, CONFIG_SYS_BR4_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR5_PRELIM) && defined(CONFIG_SYS_OR5_PRELIM)
- out_be32(&memctl->or5, CONFIG_SYS_OR5_PRELIM);
- out_be32(&memctl->br5, CONFIG_SYS_BR5_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR6_PRELIM) && defined(CONFIG_SYS_OR6_PRELIM)
- out_be32(&memctl->or6, CONFIG_SYS_OR6_PRELIM);
- out_be32(&memctl->br6, CONFIG_SYS_BR6_PRELIM);
-#endif
-
-#if defined(CONFIG_SYS_BR7_PRELIM) && defined(CONFIG_SYS_OR7_PRELIM)
- out_be32(&memctl->or7, CONFIG_SYS_OR7_PRELIM);
- out_be32(&memctl->br7, CONFIG_SYS_BR7_PRELIM);
-#endif
+ init_early_memctl_regs();
#if defined(CONFIG_CPM2)
m8560_cpm_reset();
@@ -263,7 +209,7 @@ void cpu_init_f (void)
int cpu_init_r(void)
{
#ifdef CONFIG_SYS_LBC_LCRR
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
#endif
puts ("L2: ");
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c b/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c
index 184cca4..8fb27ab 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init_nand.c
@@ -25,7 +25,7 @@
void cpu_init_f(void)
{
- ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
/*
* LCRR - Clock Ratio Register - set up local bus timing
@@ -34,8 +34,8 @@ void cpu_init_f(void)
out_be32(&lbc->lcrr, LCRR_DBYP | LCRR_CLKDIV_8);
#if defined(CONFIG_NAND_BR_PRELIM) && defined(CONFIG_NAND_OR_PRELIM)
- out_be32(&lbc->br0, CONFIG_NAND_BR_PRELIM);
- out_be32(&lbc->or0, CONFIG_NAND_OR_PRELIM);
+ set_lbc_br(0, CONFIG_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_NAND_OR_PRELIM);
#else
#error CONFIG_NAND_BR_PRELIM, CONFIG_NAND_OR_PRELIM must be defined
#endif
diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index 8132115..dd4c6b3 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -172,10 +172,7 @@ void get_sys_info (sys_info_t * sysInfo)
/* We will program LCRR to this value later */
lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV;
#else
- {
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
- lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV;
- }
+ lcrr_div = in_be32(&(LBC_BASE_ADDR)->lcrr) & LCRR_CLKDIV;
#endif
if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) {
#if defined(CONFIG_FSL_CORENET)
diff --git a/arch/powerpc/cpu/mpc86xx/cpu.c b/arch/powerpc/cpu/mpc86xx/cpu.c
index 1887575..0fe94a0 100644
--- a/arch/powerpc/cpu/mpc86xx/cpu.c
+++ b/arch/powerpc/cpu/mpc86xx/cpu.c
@@ -180,22 +180,9 @@ watchdog_reset(void)
*/
void mpc86xx_reginfo(void)
{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- ccsr_lbc_t *lbc = &immap->im_lbc;
-
print_bats();
print_laws();
-
- printf ("Local Bus Controller Registers\n"
- "\tBR0\t0x%08X\tOR0\t0x%08X \n", in_be32(&lbc->br0), in_be32(&lbc->or0));
- printf("\tBR1\t0x%08X\tOR1\t0x%08X \n", in_be32(&lbc->br1), in_be32(&lbc->or1));
- printf("\tBR2\t0x%08X\tOR2\t0x%08X \n", in_be32(&lbc->br2), in_be32(&lbc->or2));
- printf("\tBR3\t0x%08X\tOR3\t0x%08X \n", in_be32(&lbc->br3), in_be32(&lbc->or3));
- printf("\tBR4\t0x%08X\tOR4\t0x%08X \n", in_be32(&lbc->br4), in_be32(&lbc->or4));
- printf("\tBR5\t0x%08X\tOR5\t0x%08X \n", in_be32(&lbc->br5), in_be32(&lbc->or5));
- printf("\tBR6\t0x%08X\tOR6\t0x%08X \n", in_be32(&lbc->br6), in_be32(&lbc->or6));
- printf("\tBR7\t0x%08X\tOR7\t0x%08X \n", in_be32(&lbc->br7), in_be32(&lbc->or7));
-
+ print_lbc_regs();
}
/*
diff --git a/arch/powerpc/cpu/mpc86xx/cpu_init.c b/arch/powerpc/cpu/mpc86xx/cpu_init.c
index b4f047d..82c216b 100644
--- a/arch/powerpc/cpu/mpc86xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc86xx/cpu_init.c
@@ -46,9 +46,6 @@ DECLARE_GLOBAL_DATA_PTR;
void cpu_init_f(void)
{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile ccsr_lbc_t *memctl = &immap->im_lbc;
-
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
@@ -61,58 +58,8 @@ void cpu_init_f(void)
setup_bats();
- /* Map banks 0 and 1 to the FLASH banks 0 and 1 at preliminary
- * addresses - these have to be modified later when FLASH size
- * has been determined
- */
-
-#if defined(CONFIG_SYS_OR0_REMAP)
- memctl->or0 = CONFIG_SYS_OR0_REMAP;
-#endif
-#if defined(CONFIG_SYS_OR1_REMAP)
- memctl->or1 = CONFIG_SYS_OR1_REMAP;
-#endif
-
- /* now restrict to preliminary range */
-#if defined(CONFIG_SYS_BR0_PRELIM) && defined(CONFIG_SYS_OR0_PRELIM)
- memctl->br0 = CONFIG_SYS_BR0_PRELIM;
- memctl->or0 = CONFIG_SYS_OR0_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR1_PRELIM) && defined(CONFIG_SYS_OR1_PRELIM)
- memctl->or1 = CONFIG_SYS_OR1_PRELIM;
- memctl->br1 = CONFIG_SYS_BR1_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR2_PRELIM) && defined(CONFIG_SYS_OR2_PRELIM)
- memctl->or2 = CONFIG_SYS_OR2_PRELIM;
- memctl->br2 = CONFIG_SYS_BR2_PRELIM;
-#endif
+ init_early_memctl_regs();
-#if defined(CONFIG_SYS_BR3_PRELIM) && defined(CONFIG_SYS_OR3_PRELIM)
- memctl->or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->br3 = CONFIG_SYS_BR3_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR4_PRELIM) && defined(CONFIG_SYS_OR4_PRELIM)
- memctl->or4 = CONFIG_SYS_OR4_PRELIM;
- memctl->br4 = CONFIG_SYS_BR4_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR5_PRELIM) && defined(CONFIG_SYS_OR5_PRELIM)
- memctl->or5 = CONFIG_SYS_OR5_PRELIM;
- memctl->br5 = CONFIG_SYS_BR5_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR6_PRELIM) && defined(CONFIG_SYS_OR6_PRELIM)
- memctl->or6 = CONFIG_SYS_OR6_PRELIM;
- memctl->br6 = CONFIG_SYS_BR6_PRELIM;
-#endif
-
-#if defined(CONFIG_SYS_BR7_PRELIM) && defined(CONFIG_SYS_OR7_PRELIM)
- memctl->or7 = CONFIG_SYS_OR7_PRELIM;
- memctl->br7 = CONFIG_SYS_BR7_PRELIM;
-#endif
#if defined(CONFIG_FSL_DMA)
dma_init();
#endif
diff --git a/arch/powerpc/cpu/mpc86xx/speed.c b/arch/powerpc/cpu/mpc86xx/speed.c
index 64a3479..a2d0a8a 100644
--- a/arch/powerpc/cpu/mpc86xx/speed.c
+++ b/arch/powerpc/cpu/mpc86xx/speed.c
@@ -97,10 +97,7 @@ void get_sys_info(sys_info_t *sysInfo)
/* We will program LCRR to this value later */
lcrr_div = CONFIG_SYS_LBC_LCRR & LCRR_CLKDIV;
#else
- {
- volatile ccsr_lbc_t *lbc = &immap->im_lbc;
- lcrr_div = in_be32(&lbc->lcrr) & LCRR_CLKDIV;
- }
+ lcrr_div = in_be32(&immap->im_lbc.lcrr) & LCRR_CLKDIV;
#endif
if (lcrr_div == 2 || lcrr_div == 4 || lcrr_div == 8) {
sysInfo->freqLocalBus = sysInfo->freqSystemBus / (lcrr_div * 2);
diff --git a/arch/powerpc/cpu/mpc8xxx/Makefile b/arch/powerpc/cpu/mpc8xxx/Makefile
index 481f9e5..34a5198 100644
--- a/arch/powerpc/cpu/mpc8xxx/Makefile
+++ b/arch/powerpc/cpu/mpc8xxx/Makefile
@@ -10,9 +10,12 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib8xxx.a
+ifeq ($(CPU), $(filter $(CPU), mpc85xx mpc86xx))
COBJS-y += cpu.o
COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
COBJS-$(CONFIG_PCI) += pci_cfg.o
+endif
+COBJS-$(CONFIG_FSL_LBC) += fsl_lbc.o
SRCS := $(START:.o=.S) $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c b/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c
new file mode 100644
index 0000000..e0a15c4
--- /dev/null
+++ b/arch/powerpc/cpu/mpc8xxx/fsl_lbc.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright 2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/fsl_lbc.h>
+
+void print_lbc_regs(void)
+{
+ int i;
+
+ printf("\nLocal Bus Controller Registers\n");
+ for (i = 0; i < 8; i++) {
+ printf("BR%d\t0x%08X\tOR%d\t0x%08X\n",
+ i, get_lbc_br(i), i, get_lbc_or(i));
+ }
+}
+
+void init_early_memctl_regs(void)
+{
+ uint init_br1 = 1;
+
+#ifdef CONFIG_MPC85xx
+ /* if cs1 is already set via debugger, leave cs0/cs1 alone */
+ if (get_lbc_br(1) & BR_V)
+ init_br1 = 0;
+#endif
+
+ /*
+ * Map banks 0 (and maybe 1) to the FLASH banks 0 (and 1) at
+ * preliminary addresses - these have to be modified later
+ * when FLASH size has been determined
+ */
+#if defined(CONFIG_SYS_OR0_REMAP)
+ set_lbc_or(0, CONFIG_SYS_OR0_REMAP);
+#endif
+#if defined(CONFIG_SYS_OR1_REMAP)
+ set_lbc_or(1, CONFIG_SYS_OR1_REMAP);
+#endif
+ /* now restrict to preliminary range */
+ if (init_br1) {
+ set_lbc_br(0, CONFIG_SYS_BR0_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_OR0_PRELIM);
+
+#if defined(CONFIG_SYS_BR1_PRELIM) && defined(CONFIG_SYS_OR1_PRELIM)
+ set_lbc_or(1, CONFIG_SYS_OR1_PRELIM);
+ set_lbc_br(1, CONFIG_SYS_BR1_PRELIM);
+#endif
+ }
+
+#if defined(CONFIG_SYS_BR2_PRELIM) && defined(CONFIG_SYS_OR2_PRELIM)
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
+#endif
+
+#if defined(CONFIG_SYS_BR3_PRELIM) && defined(CONFIG_SYS_OR3_PRELIM)
+ set_lbc_or(3, CONFIG_SYS_OR3_PRELIM);
+ set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
+#endif
+
+#if defined(CONFIG_SYS_BR4_PRELIM) && defined(CONFIG_SYS_OR4_PRELIM)
+ set_lbc_or(4, CONFIG_SYS_OR4_PRELIM);
+ set_lbc_br(4, CONFIG_SYS_BR4_PRELIM);
+#endif
+
+#if defined(CONFIG_SYS_BR5_PRELIM) && defined(CONFIG_SYS_OR5_PRELIM)
+ set_lbc_or(5, CONFIG_SYS_OR5_PRELIM);
+ set_lbc_br(5, CONFIG_SYS_BR5_PRELIM);
+#endif
+
+#if defined(CONFIG_SYS_BR6_PRELIM) && defined(CONFIG_SYS_OR6_PRELIM)
+ set_lbc_or(6, CONFIG_SYS_OR6_PRELIM);
+ set_lbc_br(6, CONFIG_SYS_BR6_PRELIM);
+#endif
+
+#if defined(CONFIG_SYS_BR7_PRELIM) && defined(CONFIG_SYS_OR7_PRELIM)
+ set_lbc_or(7, CONFIG_SYS_OR7_PRELIM);
+ set_lbc_br(7, CONFIG_SYS_BR7_PRELIM);
+#endif
+}
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h
index fc3facb..01036f3 100644
--- a/arch/powerpc/include/asm/config.h
+++ b/arch/powerpc/include/asm/config.h
@@ -76,4 +76,10 @@
/* Relocation to SDRAM works on all PPC boards */
#define CONFIG_RELOC_FIXUP_WORKS
+/* Most PPC SOCs have a LBC so define this here */
+#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) || \
+ defined(CONFIG_MPC83xx)
+#define CONFIG_FSL_LBC
+#endif
+
#endif /* _ASM_CONFIG_H_ */
diff --git a/arch/powerpc/include/asm/fsl_lbc.h b/arch/powerpc/include/asm/fsl_lbc.h
index 03ae6a7..33e6dd9 100644
--- a/arch/powerpc/include/asm/fsl_lbc.h
+++ b/arch/powerpc/include/asm/fsl_lbc.h
@@ -14,6 +14,7 @@
#define __ASM_PPC_FSL_LBC_H
#include <config.h>
+#include <common.h>
/* BR - Base Registers
*/
@@ -453,49 +454,69 @@
#define LTESR_CC 0x00000001
#ifndef __ASSEMBLY__
-/*
- * Local Bus Controller Registers.
- */
-typedef struct lbus_bank {
- u32 br; /* Base Register */
- u32 or; /* Option Register */
-} lbus_bank_t;
-
-typedef struct fsl_lbus {
- lbus_bank_t bank[8];
- u8 res0[0x28];
- u32 mar; /* UPM Address Register */
- u8 res1[0x4];
- u32 mamr; /* UPMA Mode Register */
- u32 mbmr; /* UPMB Mode Register */
- u32 mcmr; /* UPMC Mode Register */
- u8 res2[0x8];
- u32 mrtpr; /* Memory Refresh Timer Prescaler Register */
- u32 mdr; /* UPM Data Register */
- u8 res3[0x4];
- u32 lsor; /* Special Operation Initiation Register */
- u32 lsdmr; /* SDRAM Mode Register */
- u8 res4[0x8];
- u32 lurt; /* UPM Refresh Timer */
- u32 lsrt; /* SDRAM Refresh Timer */
- u8 res5[0x8];
- u32 ltesr; /* Transfer Error Status Register */
- u32 ltedr; /* Transfer Error Disable Register */
- u32 lteir; /* Transfer Error Interrupt Register */
- u32 lteatr; /* Transfer Error Attributes Register */
- u32 ltear; /* Transfer Error Address Register */
- u8 res6[0xC];
- u32 lbcr; /* Configuration Register */
- u32 lcrr; /* Clock Ratio Register */
- u8 res7[0x8];
- u32 fmr; /* Flash Mode Register */
- u32 fir; /* Flash Instruction Register */
- u32 fcr; /* Flash Command Register */
- u32 fbar; /* Flash Block Addr Register */
- u32 fpar; /* Flash Page Addr Register */
- u32 fbcr; /* Flash Byte Count Register */
- u8 res8[0xF08];
-} fsl_lbus_t;
-#endif /* __ASSEMBLY__ */
+#include <asm/io.h>
+
+extern void print_lbc_regs(void);
+extern void init_early_memctl_regs(void);
+
+#define LBC_BASE_ADDR ((fsl_lbc_t *)CONFIG_SYS_LBC_ADDR)
+#define get_lbc_br(i) (in_be32(&(LBC_BASE_ADDR)->bank[i].br))
+#define get_lbc_or(i) (in_be32(&(LBC_BASE_ADDR)->bank[i].or))
+#define set_lbc_br(i, v) (out_be32(&(LBC_BASE_ADDR)->bank[i].br, v))
+#define set_lbc_or(i, v) (out_be32(&(LBC_BASE_ADDR)->bank[i].or, v))
+
+typedef struct lbc_bank {
+ u32 br;
+ u32 or;
+} lbc_bank_t;
+/* Local Bus Controller Registers */
+typedef struct fsl_lbc {
+ lbc_bank_t bank[8];
+ u8 res1[40];
+ u32 mar; /* LBC UPM Addr */
+ u8 res2[4];
+ u32 mamr; /* LBC UPMA Mode */
+ u32 mbmr; /* LBC UPMB Mode */
+ u32 mcmr; /* LBC UPMC Mode */
+ u8 res3[8];
+ u32 mrtpr; /* LBC Memory Refresh Timer Prescaler */
+ u32 mdr; /* LBC UPM Data */
+#ifdef CONFIG_FSL_ELBC
+ u8 res4[4];
+ u32 lsor;
+ u8 res5[12];
+ u32 lurt; /* LBC UPM Refresh Timer */
+ u8 res6[4];
+#else
+ u8 res4[8];
+ u32 lsdmr; /* LBC SDRAM Mode */
+ u8 res5[8];
+ u32 lurt; /* LBC UPM Refresh Timer */
+ u32 lsrt; /* LBC SDRAM Refresh Timer */
+#endif
+ u8 res7[8];
+ u32 ltesr; /* LBC Transfer Error Status */
+ u32 ltedr; /* LBC Transfer Error Disable */
+ u32 lteir; /* LBC Transfer Error IRQ */
+ u32 lteatr; /* LBC Transfer Error Attrs */
+ u32 ltear; /* LBC Transfer Error Addr */
+ u8 res8[12];
+ u32 lbcr; /* LBC Configuration */
+ u32 lcrr; /* LBC Clock Ratio */
+#ifdef CONFIG_NAND_FSL_ELBC
+ u8 res9[0x8];
+ u32 fmr; /* Flash Mode Register */
+ u32 fir; /* Flash Instruction Register */
+ u32 fcr; /* Flash Command Register */
+ u32 fbar; /* Flash Block Addr Register */
+ u32 fpar; /* Flash Page Addr Register */
+ u32 fbcr; /* Flash Byte Count Register */
+ u8 res10[0xF08];
+#else
+ u8 res9[0xF28];
+#endif
+} fsl_lbc_t;
+
+#endif /* __ASSEMBLY__ */
#endif /* __ASM_PPC_FSL_LBC_H */
diff --git a/arch/powerpc/include/asm/immap_83xx.h b/arch/powerpc/include/asm/immap_83xx.h
index 6b42a73..9353dc0 100644
--- a/arch/powerpc/include/asm/immap_83xx.h
+++ b/arch/powerpc/include/asm/immap_83xx.h
@@ -635,7 +635,7 @@ typedef struct immap {
u8 res2[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res3[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res4[0x1000];
spi8xxx_t spi; /* Serial Peripheral Interface */
dma83xx_t dma; /* DMA */
@@ -675,7 +675,7 @@ typedef struct immap {
u8 res1[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res2[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res3[0x1000];
spi8xxx_t spi; /* Serial Peripheral Interface */
dma83xx_t dma; /* DMA */
@@ -710,7 +710,7 @@ typedef struct immap {
u8 res1[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res2[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res3[0x1000];
spi8xxx_t spi; /* Serial Peripheral Interface */
dma83xx_t dma; /* DMA */
@@ -755,7 +755,7 @@ typedef struct immap {
u8 res1[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res2[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res3[0x1000];
spi8xxx_t spi; /* Serial Peripheral Interface */
dma83xx_t dma; /* DMA */
@@ -805,7 +805,7 @@ typedef struct immap {
u8 res4[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res5[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res6[0x2000];
dma83xx_t dma; /* DMA */
pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */
@@ -844,7 +844,7 @@ typedef struct immap {
u8 res3[0x1300];
duart83xx_t duart[2]; /* DUART */
u8 res4[0x900];
- fsl_lbus_t lbus; /* Local Bus Controller Registers */
+ fsl_lbc_t im_lbc; /* Local Bus Controller Regs */
u8 res5[0x2000];
dma83xx_t dma; /* DMA */
pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */
@@ -868,6 +868,7 @@ typedef struct immap {
#endif
#define CONFIG_SYS_MPC83xx_USB_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB_OFFSET)
+#define CONFIG_SYS_LBC_ADDR (&((immap_t *)CONFIG_SYS_IMMR)->im_lbc)
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_MDIO1_OFFSET 0x24000
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 5b205d1..d020f44 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -266,50 +266,6 @@ typedef struct ccsr_duart {
} ccsr_duart_t;
#endif
-/* Local Bus Controller Registers */
-typedef struct ccsr_lbc {
- u32 br0; /* LBC Base 0 */
- u32 or0; /* LBC Options 0 */
- u32 br1; /* LBC Base 1 */
- u32 or1; /* LBC Options 1 */
- u32 br2; /* LBC Base 2 */
- u32 or2; /* LBC Options 2 */
- u32 br3; /* LBC Base 3 */
- u32 or3; /* LBC Options 3 */
- u32 br4; /* LBC Base 4 */
- u32 or4; /* LBC Options 4 */
- u32 br5; /* LBC Base 5 */
- u32 or5; /* LBC Options 5 */
- u32 br6; /* LBC Base 6 */
- u32 or6; /* LBC Options 6 */
- u32 br7; /* LBC Base 7 */
- u32 or7; /* LBC Options 7 */
- u8 res1[40];
- u32 mar; /* LBC UPM Addr */
- u8 res2[4];
- u32 mamr; /* LBC UPMA Mode */
- u32 mbmr; /* LBC UPMB Mode */
- u32 mcmr; /* LBC UPMC Mode */
- u8 res3[8];
- u32 mrtpr; /* LBC Memory Refresh Timer Prescaler */
- u32 mdr; /* LBC UPM Data */
- u8 res4[8];
- u32 lsdmr; /* LBC SDRAM Mode */
- u8 res5[8];
- u32 lurt; /* LBC UPM Refresh Timer */
- u32 lsrt; /* LBC SDRAM Refresh Timer */
- u8 res6[8];
- u32 ltesr; /* LBC Transfer Error Status */
- u32 ltedr; /* LBC Transfer Error Disable */
- u32 lteir; /* LBC Transfer Error IRQ */
- u32 lteatr; /* LBC Transfer Error Attrs */
- u32 ltear; /* LBC Transfer Error Addr */
- u8 res7[12];
- u32 lbcr; /* LBC Configuration */
- u32 lcrr; /* LBC Clock Ratio */
- u8 res8[3880];
-} ccsr_lbc_t;
-
/* eSPI Registers */
typedef struct ccsr_espi {
u32 mode; /* eSPI mode */
@@ -2111,7 +2067,7 @@ enum {
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR_OFFSET)
#define CONFIG_SYS_MPC85xx_DDR2_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR2_OFFSET)
-#define CONFIG_SYS_MPC85xx_LBC_ADDR \
+#define CONFIG_SYS_LBC_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_LBC_OFFSET)
#define CONFIG_SYS_MPC85xx_ESPI_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_ESPI_OFFSET)
diff --git a/arch/powerpc/include/asm/immap_86xx.h b/arch/powerpc/include/asm/immap_86xx.h
index fd7acdb..b9e02db 100644
--- a/arch/powerpc/include/asm/immap_86xx.h
+++ b/arch/powerpc/include/asm/immap_86xx.h
@@ -12,6 +12,7 @@
#include <asm/types.h>
#include <asm/fsl_dma.h>
+#include <asm/fsl_lbc.h>
#include <asm/fsl_i2c.h>
/* Local-Access Registers and MCM Registers(0x0000-0x2000) */
@@ -190,51 +191,6 @@ typedef struct ccsr_duart {
char res5[2543];
} ccsr_duart_t;
-
-/* Local Bus Controller Registers(0x5000-0x6000) */
-typedef struct ccsr_lbc {
- uint br0; /* 0x5000 - LBC Base Register 0 */
- uint or0; /* 0x5004 - LBC Options Register 0 */
- uint br1; /* 0x5008 - LBC Base Register 1 */
- uint or1; /* 0x500c - LBC Options Register 1 */
- uint br2; /* 0x5010 - LBC Base Register 2 */
- uint or2; /* 0x5014 - LBC Options Register 2 */
- uint br3; /* 0x5018 - LBC Base Register 3 */
- uint or3; /* 0x501c - LBC Options Register 3 */
- uint br4; /* 0x5020 - LBC Base Register 4 */
- uint or4; /* 0x5024 - LBC Options Register 4 */
- uint br5; /* 0x5028 - LBC Base Register 5 */
- uint or5; /* 0x502c - LBC Options Register 5 */
- uint br6; /* 0x5030 - LBC Base Register 6 */
- uint or6; /* 0x5034 - LBC Options Register 6 */
- uint br7; /* 0x5038 - LBC Base Register 7 */
- uint or7; /* 0x503c - LBC Options Register 7 */
- char res1[40];
- uint mar; /* 0x5068 - LBC UPM Address Register */
- char res2[4];
- uint mamr; /* 0x5070 - LBC UPMA Mode Register */
- uint mbmr; /* 0x5074 - LBC UPMB Mode Register */
- uint mcmr; /* 0x5078 - LBC UPMC Mode Register */
- char res3[8];
- uint mrtpr; /* 0x5084 - LBC Memory Refresh Timer Prescaler Register */
- uint mdr; /* 0x5088 - LBC UPM Data Register */
- char res4[8];
- uint lsdmr; /* 0x5094 - LBC SDRAM Mode Register */
- char res5[8];
- uint lurt; /* 0x50a0 - LBC UPM Refresh Timer */
- uint lsrt; /* 0x50a4 - LBC SDRAM Refresh Timer */
- char res6[8];
- uint ltesr; /* 0x50b0 - LBC Transfer Error Status Register */
- uint ltedr; /* 0x50b4 - LBC Transfer Error Disable Register */
- uint lteir; /* 0x50b8 - LBC Transfer Error Interrupt Register */
- uint lteatr; /* 0x50bc - LBC Transfer Error Attributes Register */
- uint ltear; /* 0x50c0 - LBC Transfer Error Address Register */
- char res7[12];
- uint lbcr; /* 0x50d0 - LBC Configuration Register */
- uint lcrr; /* 0x50d4 - LBC Clock Ratio Register */
- char res8[3880];
-} ccsr_lbc_t;
-
/* PCI Express Registers(0x8000-0x9000) and (0x9000-0xA000) */
typedef struct ccsr_pex {
uint cfg_addr; /* 0x8000 - PEX Configuration Address Register */
@@ -1270,7 +1226,7 @@ typedef struct immap {
ccsr_ddr_t im_ddr1;
ccsr_i2c_t im_i2c;
ccsr_duart_t im_duart;
- ccsr_lbc_t im_lbc;
+ fsl_lbc_t im_lbc;
ccsr_ddr_t im_ddr2;
char res1[4096];
ccsr_pex_t im_pex1;
@@ -1303,6 +1259,7 @@ extern immap_t *immr;
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_MDIO1_OFFSET 0x24000
+#define CONFIG_SYS_LBC_ADDR (&((immap_t *)CONFIG_SYS_IMMR)->im_lbc)
#define TSEC_BASE_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
#define MDIO_BASE_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
diff --git a/board/atum8548/atum8548.c b/board/atum8548/atum8548.c
index c11a5c3..4f7d935 100644
--- a/board/atum8548/atum8548.c
+++ b/board/atum8548/atum8548.c
@@ -47,7 +47,7 @@ int board_early_init_f (void)
int checkboard (void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
if ((uint)&gur->porpllsr != 0xe00e0000) {
diff --git a/board/esd/vme8349/vme8349.c b/board/esd/vme8349/vme8349.c
index b0ebad7..96698e7 100644
--- a/board/esd/vme8349/vme8349.c
+++ b/board/esd/vme8349/vme8349.c
@@ -105,7 +105,7 @@ int misc_init_r()
{
immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- clrsetbits_be32(&im->lbus.lcrr, LBCR_LDIS, 0);
+ clrsetbits_be32(&im->im_lbc.lcrr, LBCR_LDIS, 0);
return 0;
}
diff --git a/board/freescale/mpc8313erdb/sdram.c b/board/freescale/mpc8313erdb/sdram.c
index 0c4fd68..7aede13 100644
--- a/board/freescale/mpc8313erdb/sdram.c
+++ b/board/freescale/mpc8313erdb/sdram.c
@@ -110,7 +110,7 @@ static long fixed_sdram(void)
phys_size_t initdram(int board_type)
{
volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbc = &im->lbus;
+ volatile fsl_lbc_t *lbc = &im->im_lbc;
u32 msize;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
diff --git a/board/freescale/mpc8349emds/mpc8349emds.c b/board/freescale/mpc8349emds/mpc8349emds.c
index 61d1249..365ac37 100644
--- a/board/freescale/mpc8349emds/mpc8349emds.c
+++ b/board/freescale/mpc8349emds/mpc8349emds.c
@@ -192,7 +192,7 @@ int checkboard (void)
void sdram_init(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbc = &immap->lbus;
+ volatile fsl_lbc_t *lbc = &immap->im_lbc;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
/*
diff --git a/board/freescale/mpc8349itx/mpc8349itx.c b/board/freescale/mpc8349itx/mpc8349itx.c
index 7da39f1..5647579 100644
--- a/board/freescale/mpc8349itx/mpc8349itx.c
+++ b/board/freescale/mpc8349itx/mpc8349itx.c
@@ -221,15 +221,14 @@ int misc_init_f(void)
0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01
};
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbus = &immap->lbus;
- lbus->bank[3].br = CONFIG_SYS_BR3_PRELIM;
- lbus->bank[3].or = CONFIG_SYS_OR3_PRELIM;
+ set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
+ set_lbc_or(3, CONFIG_SYS_OR3_PRELIM);
/* Program the MAMR. RFEN=0, OP=00, UWPL=1, AM=000, DS=01, G0CL=000,
GPL4=0, RLF=0001, WLF=0001, TLF=0001, MAD=000000
*/
- lbus->mamr = 0x08404440;
+ immap->im_lbc.mamr = 0x08404440;
upmconfig(0, UPMATable, sizeof(UPMATable) / sizeof(UPMATable[0]));
diff --git a/board/freescale/mpc8360emds/mpc8360emds.c b/board/freescale/mpc8360emds/mpc8360emds.c
index 4f55732..59ada9c 100644
--- a/board/freescale/mpc8360emds/mpc8360emds.c
+++ b/board/freescale/mpc8360emds/mpc8360emds.c
@@ -280,7 +280,7 @@ int checkboard(void)
static int sdram_init(unsigned int base)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbc = &immap->lbus;
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
const int sdram_size = CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024;
int rem = base % sdram_size;
uint *sdram_addr;
@@ -293,8 +293,8 @@ static int sdram_init(unsigned int base)
/*
* Setup SDRAM Base and Option Registers
*/
- immap->lbus.bank[2].br = base | CONFIG_SYS_BR2;
- immap->lbus.bank[2].or = CONFIG_SYS_OR2;
+ set_lbc_br(2, base | CONFIG_SYS_BR2);
+ set_lbc_or(2, CONFIG_SYS_OR2);
immap->sysconf.lblaw[2].bar = base;
immap->sysconf.lblaw[2].ar = CONFIG_SYS_LBLAWAR2;
diff --git a/board/freescale/mpc8360erdk/nand.c b/board/freescale/mpc8360erdk/nand.c
index 9ffffb4..92d56a3 100644
--- a/board/freescale/mpc8360erdk/nand.c
+++ b/board/freescale/mpc8360erdk/nand.c
@@ -82,9 +82,9 @@ static struct fsl_upm_nand fun = {
int board_nand_init(struct nand_chip *nand)
{
- fun.upm.mxmr = &im->lbus.mamr;
- fun.upm.mdr = &im->lbus.mdr;
- fun.upm.mar = &im->lbus.mar;
+ fun.upm.mxmr = &im->im_lbc.mamr;
+ fun.upm.mdr = &im->im_lbc.mdr;
+ fun.upm.mar = &im->im_lbc.mar;
upm_setup(&fun.upm);
diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c
index 9e3f677..f9ff827 100644
--- a/board/freescale/mpc8540ads/mpc8540ads.c
+++ b/board/freescale/mpc8540ads/mpc8540ads.c
@@ -117,7 +117,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -176,7 +176,7 @@ local_bus_init(void)
void
sdram_init(void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
puts(" SDRAM: ");
@@ -185,8 +185,8 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
diff --git a/board/freescale/mpc8541cds/mpc8541cds.c b/board/freescale/mpc8541cds/mpc8541cds.c
index c30d966..0580fe7 100644
--- a/board/freescale/mpc8541cds/mpc8541cds.c
+++ b/board/freescale/mpc8541cds/mpc8541cds.c
@@ -291,7 +291,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -340,7 +340,7 @@ sdram_init(void)
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
uint idx;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint cpu_board_rev;
uint lsdmr_common;
@@ -352,16 +352,11 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- asm("msync");
-
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
- asm("msync");
-
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
-
lbc->lsrt = CONFIG_SYS_LBC_LSRT;
lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
asm("msync");
diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c
index 0be2d89..581d5f2 100644
--- a/board/freescale/mpc8544ds/mpc8544ds.c
+++ b/board/freescale/mpc8544ds/mpc8544ds.c
@@ -40,7 +40,7 @@
int checkboard (void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
u8 vboot;
u8 *pixis_base = (u8 *)PIXIS_BASE;
diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c
index aa3f32b..f016995 100644
--- a/board/freescale/mpc8548cds/mpc8548cds.c
+++ b/board/freescale/mpc8548cds/mpc8548cds.c
@@ -118,7 +118,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -154,7 +154,7 @@ sdram_init(void)
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
uint idx;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint cpu_board_rev;
uint lsdmr_common;
@@ -166,16 +166,11 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- asm("msync");
-
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
- asm("msync");
-
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
-
lbc->lsrt = CONFIG_SYS_LBC_LSRT;
lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
asm("msync");
diff --git a/board/freescale/mpc8555cds/mpc8555cds.c b/board/freescale/mpc8555cds/mpc8555cds.c
index ecddd0d..b7e0e0c 100644
--- a/board/freescale/mpc8555cds/mpc8555cds.c
+++ b/board/freescale/mpc8555cds/mpc8555cds.c
@@ -291,7 +291,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -340,7 +340,7 @@ sdram_init(void)
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
uint idx;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint cpu_board_rev;
uint lsdmr_common;
@@ -352,12 +352,8 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- asm("msync");
-
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
- asm("msync");
-
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c
index 2bca0f2..489f90b 100644
--- a/board/freescale/mpc8560ads/mpc8560ads.c
+++ b/board/freescale/mpc8560ads/mpc8560ads.c
@@ -322,7 +322,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -381,7 +381,7 @@ local_bus_init(void)
void
sdram_init(void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
puts(" SDRAM: ");
@@ -390,8 +390,8 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c
index 4ec13a9..036bf95 100644
--- a/board/freescale/mpc8568mds/mpc8568mds.c
+++ b/board/freescale/mpc8568mds/mpc8568mds.c
@@ -181,7 +181,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -214,7 +214,7 @@ sdram_init(void)
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
uint idx;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint lsdmr_common;
@@ -225,16 +225,13 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- lbc->or2 = CONFIG_SYS_OR2_PRELIM;
- asm("msync");
-
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
asm("msync");
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
-
lbc->lsrt = CONFIG_SYS_LBC_LSRT;
lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
asm("msync");
diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c
index 1eddeef..81e8ff5 100644
--- a/board/freescale/mpc8569mds/mpc8569mds.c
+++ b/board/freescale/mpc8569mds/mpc8569mds.c
@@ -308,7 +308,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
diff --git a/board/mpc8540eval/mpc8540eval.c b/board/mpc8540eval/mpc8540eval.c
index 7c27233..054d644 100644
--- a/board/mpc8540eval/mpc8540eval.c
+++ b/board/mpc8540eval/mpc8540eval.c
@@ -69,7 +69,7 @@ phys_size_t initdram (int board_type)
long dram_size = 0;
#if !defined(CONFIG_RAM_AS_FLASH)
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
sys_info_t sysinfo;
uint temp_lbcdll = 0;
#endif
@@ -110,8 +110,8 @@ phys_size_t initdram (int board_type)
gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16 ) | 0x80000000;
asm("sync;isync;msync");
}
- lbc->or2 = CONFIG_SYS_OR2_PRELIM; /* 64MB SDRAM */
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); /* 64MB SDRAM */
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1;
asm("sync");
diff --git a/board/pm854/pm854.c b/board/pm854/pm854.c
index 5353d73..a302b91 100644
--- a/board/pm854/pm854.c
+++ b/board/pm854/pm854.c
@@ -134,7 +134,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
diff --git a/board/pm856/pm856.c b/board/pm856/pm856.c
index b14a3d3..f9d92d9 100644
--- a/board/pm856/pm856.c
+++ b/board/pm856/pm856.c
@@ -290,7 +290,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
diff --git a/board/sbc8349/sbc8349.c b/board/sbc8349/sbc8349.c
index 34861d4..50fae7c 100644
--- a/board/sbc8349/sbc8349.c
+++ b/board/sbc8349/sbc8349.c
@@ -160,7 +160,7 @@ int checkboard (void)
void sdram_init(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbc = &immap->lbus;
+ volatile fsl_lbc_t *lbc = &immap->im_lbc;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
puts("\n SDRAM on Local Bus: ");
diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c
index 194f6ab..d62cfd1 100644
--- a/board/sbc8548/sbc8548.c
+++ b/board/sbc8548/sbc8548.c
@@ -116,7 +116,7 @@ void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
@@ -152,7 +152,7 @@ sdram_init(void)
#if defined(CONFIG_SYS_LBC_SDRAM_SIZE)
uint idx;
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint lsdmr_common;
@@ -163,22 +163,14 @@ sdram_init(void)
/*
* Setup SDRAM Base and Option Registers
*/
- out_be32(&lbc->or3, CONFIG_SYS_OR3_PRELIM);
- asm("msync");
-
- out_be32(&lbc->br3, CONFIG_SYS_BR3_PRELIM);
- asm("msync");
-
- out_be32(&lbc->or4, CONFIG_SYS_OR4_PRELIM);
- asm("msync");
-
- out_be32(&lbc->br4, CONFIG_SYS_BR4_PRELIM);
- asm("msync");
+ set_lbc_or(3, CONFIG_SYS_OR3_PRELIM);
+ set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
+ set_lbc_or(4, CONFIG_SYS_OR4_PRELIM);
+ set_lbc_br(4, CONFIG_SYS_BR4_PRELIM);
out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
asm("msync");
-
out_be32(&lbc->lsrt, CONFIG_SYS_LBC_LSRT);
out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
asm("msync");
diff --git a/board/sbc8560/sbc8560.c b/board/sbc8560/sbc8560.c
index c40b5e3..10ba62f 100644
--- a/board/sbc8560/sbc8560.c
+++ b/board/sbc8560/sbc8560.c
@@ -269,7 +269,7 @@ phys_size_t initdram (int board_type)
#if 0
#if !defined(CONFIG_RAM_AS_FLASH)
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
sys_info_t sysinfo;
uint temp_lbcdll = 0;
#endif
@@ -310,8 +310,8 @@ phys_size_t initdram (int board_type)
gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16 ) | 0x80000000;
asm("sync;isync;msync");
}
- lbc->or2 = CONFIG_SYS_OR2_PRELIM; /* 64MB SDRAM */
- lbc->br2 = CONFIG_SYS_BR2_PRELIM;
+ set_lbc_or(2, CONFIG_SYS_OR2_PRELIM); /* 64MB SDRAM */
+ set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1;
asm("sync");
diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c
index ebb70a2..ba59943 100644
--- a/board/sheldon/simpc8313/sdram.c
+++ b/board/sheldon/simpc8313/sdram.c
@@ -129,7 +129,7 @@ void si_read_i2c(u32 lbyte, int count, u8 *buffer)
phys_size_t initdram(int board_type)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile fsl_lbus_t *lbc= &im->lbus;
+ volatile fsl_lbc_t *lbc = &im->im_lbc;
u32 msize;
if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c
index cb30b48..c2164c9 100644
--- a/board/sheldon/simpc8313/simpc8313.c
+++ b/board/sheldon/simpc8313/simpc8313.c
@@ -93,7 +93,7 @@ int misc_init_r(void)
{
int rc = 0;
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- fsl_lbus_t *lbus = &immap->lbus;
+ fsl_lbc_t *lbus = &immap->im_lbc;
u32 *mxmr = &lbus->mamr; /* Pointer to mamr */
/* UPM Table Configuration Code */
diff --git a/board/socrates/socrates.c b/board/socrates/socrates.c
index 9183c15..72e7401 100644
--- a/board/socrates/socrates.c
+++ b/board/socrates/socrates.c
@@ -87,8 +87,6 @@ int checkboard (void)
int misc_init_r (void)
{
- volatile ccsr_lbc_t *memctl = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
-
/*
* Adjust flash start and offset to detected values
*/
@@ -99,8 +97,10 @@ int misc_init_r (void)
* Check if boot FLASH isn't max size
*/
if (gd->bd->bi_flashsize < (0 - CONFIG_SYS_FLASH0)) {
- memctl->or0 = gd->bd->bi_flashstart | (CONFIG_SYS_OR0_PRELIM & 0x00007fff);
- memctl->br0 = gd->bd->bi_flashstart | (CONFIG_SYS_BR0_PRELIM & 0x00007fff);
+ set_lbc_or(0, gd->bd->bi_flashstart |
+ (CONFIG_SYS_OR0_PRELIM & 0x00007fff));
+ set_lbc_br(0, gd->bd->bi_flashstart |
+ (CONFIG_SYS_BR0_PRELIM & 0x00007fff));
/*
* Re-check to get correct base address
@@ -112,8 +112,8 @@ int misc_init_r (void)
* Check if only one FLASH bank is available
*/
if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
- memctl->or1 = 0;
- memctl->br1 = 0;
+ set_lbc_or(1, 0);
+ set_lbc_br(1, 0);
/*
* Re-do flash protection upon new addresses
@@ -148,7 +148,7 @@ int misc_init_r (void)
*/
void local_bus_init (void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
sys_info_t sysinfo;
uint clkdiv;
@@ -299,26 +299,25 @@ const gdc_regs *board_get_regs (void)
int lime_probe(void)
{
- volatile ccsr_lbc_t *memctl = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
uint cfg_br2;
uint cfg_or2;
int type;
- cfg_br2 = memctl->br2;
- cfg_or2 = memctl->or2;
+ cfg_br2 = get_lbc_br(2);
+ cfg_or2 = get_lbc_or(2);
/* Configure GPCM for CS2 */
- memctl->br2 = 0;
- memctl->or2 = 0xfc000410;
- memctl->br2 = (CONFIG_SYS_LIME_BASE) | 0x00001901;
+ set_lbc_br(2, 0);
+ set_lbc_or(2, 0xfc000410);
+ set_lbc_br(2, (CONFIG_SYS_LIME_BASE) | 0x00001901);
/* Get controller type */
type = mb862xx_probe(CONFIG_SYS_LIME_BASE);
/* Restore previous CS2 configuration */
- memctl->br2 = 0;
- memctl->or2 = cfg_or2;
- memctl->br2 = cfg_br2;
+ set_lbc_br(2, 0);
+ set_lbc_or(2, cfg_or2);
+ set_lbc_br(2, cfg_br2);
return (type == MB862XX_TYPE_LIME) ? 1 : 0;
}
diff --git a/board/tqc/tqm834x/tqm834x.c b/board/tqc/tqm834x/tqm834x.c
index e564879..8d046f4 100644
--- a/board/tqc/tqm834x/tqm834x.c
+++ b/board/tqc/tqm834x/tqm834x.c
@@ -253,10 +253,10 @@ static int detect_num_flash_banks(void)
debug("Number of flash banks detected: %d\n", tqm834x_num_flash_banks);
/* set OR0 and BR0 */
- im->lbus.bank[0].or = CONFIG_SYS_OR_TIMING_FLASH |
- (-(total_size) & OR_GPCM_AM);
- im->lbus.bank[0].br = (CONFIG_SYS_FLASH_BASE & BR_BA) |
- (BR_MS_GPCM | BR_PS_32 | BR_V);
+ set_lbc_or(0, CONFIG_SYS_OR_TIMING_FLASH |
+ (-(total_size) & OR_GPCM_AM));
+ set_lbc_br(0, (CONFIG_SYS_FLASH_BASE & BR_BA) |
+ (BR_MS_GPCM | BR_PS_32 | BR_V));
return (0);
}
diff --git a/board/tqc/tqm85xx/nand.c b/board/tqc/tqm85xx/nand.c
index 3da689a..4b16c31 100644
--- a/board/tqc/tqm85xx/nand.c
+++ b/board/tqc/tqm85xx/nand.c
@@ -377,7 +377,7 @@ volatile const u32 *nand_upm_patt;
*/
static void upmb_write (u_char addr, ulong val)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
out_be32 (&lbc->mdr, val);
@@ -393,14 +393,14 @@ static void upmb_write (u_char addr, ulong val)
/*
* Initialize UPM for NAND flash access.
*/
-static void nand_upm_setup (volatile ccsr_lbc_t *lbc)
+static void nand_upm_setup (volatile fsl_lbc_t *lbc)
{
uint i, j;
uint or3 = CONFIG_SYS_OR3_PRELIM;
uint clock = get_lbc_clock ();
- out_be32 (&lbc->br3, 0); /* disable bank and reset all bits */
- out_be32 (&lbc->br3, CONFIG_SYS_BR3_PRELIM);
+ set_lbc_br(3, 0); /* disable bank and reset all bits */
+ set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
/*
* Search appropriate UPM table for bus clock.
@@ -424,7 +424,7 @@ static void nand_upm_setup (volatile ccsr_lbc_t *lbc)
/* EAD must be set due to TQM8548 timing specification */
or3 |= OR_UPM_EAD;
- out_be32 (&lbc->or3, or3);
+ set_lbc_or(3, or3);
/* Assign address of table */
nand_upm_patt = upm_freq_table[i].upm_patt;
@@ -458,7 +458,7 @@ void board_nand_select_device (struct nand_chip *nand, int chip)
int board_nand_init (struct nand_chip *nand)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
if (!nand_upm_patt)
nand_upm_setup (lbc);
diff --git a/board/tqc/tqm85xx/tqm85xx.c b/board/tqc/tqm85xx/tqm85xx.c
index 8c9d586..fc2a6cb 100644
--- a/board/tqc/tqm85xx/tqm85xx.c
+++ b/board/tqc/tqm85xx/tqm85xx.c
@@ -269,8 +269,6 @@ int checkboard (void)
int misc_init_r (void)
{
- volatile ccsr_lbc_t *memctl = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
-
/*
* Adjust flash start and offset to detected values
*/
@@ -281,26 +279,27 @@ int misc_init_r (void)
* Recalculate CS configuration if second FLASH bank is available
*/
if (flash_info[0].size > 0) {
- memctl->or1 = ((-flash_info[0].size) & 0xffff8000) |
- (CONFIG_SYS_OR1_PRELIM & 0x00007fff);
- memctl->br1 = gd->bd->bi_flashstart |
- (CONFIG_SYS_BR1_PRELIM & 0x00007fff);
+ set_lbc_or(1, ((-flash_info[0].size) & 0xffff8000) |
+ (CONFIG_SYS_OR1_PRELIM & 0x00007fff));
+ set_lbc_br(1, gd->bd->bi_flashstart |
+ (CONFIG_SYS_BR1_PRELIM & 0x00007fff));
/*
* Re-check to get correct base address for bank 1
*/
flash_get_size (gd->bd->bi_flashstart, 0);
} else {
- memctl->or1 = 0;
- memctl->br1 = 0;
+ set_lbc_or(1, 0);
+ set_lbc_br(1, 0);
}
/*
* If bank 1 is equipped, bank 0 is mapped after bank 1
*/
- memctl->or0 = ((-flash_info[1].size) & 0xffff8000) |
- (CONFIG_SYS_OR0_PRELIM & 0x00007fff);
- memctl->br0 = (gd->bd->bi_flashstart + flash_info[0].size) |
- (CONFIG_SYS_BR0_PRELIM & 0x00007fff);
+ set_lbc_or(0, ((-flash_info[1].size) & 0xffff8000) |
+ (CONFIG_SYS_OR0_PRELIM & 0x00007fff));
+ set_lbc_br(0, gd->bd->bi_flashstart |
+ (CONFIG_SYS_BR0_PRELIM & 0x00007fff));
+
/*
* Re-check to get correct base address for bank 0
*/
@@ -341,7 +340,7 @@ int misc_init_r (void)
*/
static void upmc_write (u_char addr, uint val)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
out_be32 (&lbc->mdr, val);
@@ -358,7 +357,7 @@ static void upmc_write (u_char addr, uint val)
uint get_lbc_clock (void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
sys_info_t sys_info;
ulong clkdiv = lbc->lcrr & LCRR_CLKDIV;
@@ -386,7 +385,7 @@ uint get_lbc_clock (void)
void local_bus_init (void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint lbc_mhz = get_lbc_clock () / 1000000;
#ifdef CONFIG_MPC8548
@@ -502,10 +501,10 @@ void local_bus_init (void)
* set if Local Bus Clock is > 83 MHz.
*/
if (lbc_mhz > 83)
- out_be32 (&lbc->or2, CONFIG_SYS_OR2_CAN | OR_UPM_EAD);
+ set_lbc_or(2, CONFIG_SYS_OR2_CAN | OR_UPM_EAD);
else
- out_be32 (&lbc->or2, CONFIG_SYS_OR2_CAN);
- out_be32 (&lbc->br2, CONFIG_SYS_BR2_CAN);
+ set_lbc_or(2, CONFIG_SYS_OR2_CAN);
+ set_lbc_br(2, CONFIG_SYS_BR2_CAN);
/* LGPL4 is UPWAIT */
out_be32(&lbc->mcmr, MxMR_DSx_3_CYCL | MxMR_GPL_x4DIS | MxMR_WLFx_3X);
diff --git a/board/xes/xpedite5170/xpedite5170.c b/board/xes/xpedite5170/xpedite5170.c
index f4231a9..5822941 100644
--- a/board/xes/xpedite5170/xpedite5170.c
+++ b/board/xes/xpedite5170/xpedite5170.c
@@ -56,8 +56,6 @@ int checkboard(void)
*/
static void flash_cs_fixup(void)
{
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- ccsr_lbc_t *lbc = &immap->im_lbc;
int flash_sel;
/*
@@ -70,11 +68,11 @@ static void flash_cs_fixup(void)
printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
if (flash_sel) {
- out_be32(&lbc->br0, CONFIG_SYS_BR1_PRELIM);
- out_be32(&lbc->or0, CONFIG_SYS_OR1_PRELIM);
+ set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
- out_be32(&lbc->br1, CONFIG_SYS_BR0_PRELIM);
- out_be32(&lbc->or1, CONFIG_SYS_OR0_PRELIM);
+ set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
+ set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
}
}
diff --git a/board/xes/xpedite5200/xpedite5200.c b/board/xes/xpedite5200/xpedite5200.c
index 7109771..a2627f8 100644
--- a/board/xes/xpedite5200/xpedite5200.c
+++ b/board/xes/xpedite5200/xpedite5200.c
@@ -38,7 +38,7 @@ extern void ft_board_pci_setup(void *blob, bd_t *bd);
int checkboard(void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR);
char *s;
@@ -65,7 +65,6 @@ int checkboard(void)
static void flash_cs_fixup(void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
int flash_sel;
/*
@@ -78,11 +77,11 @@ static void flash_cs_fixup(void)
printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
if (flash_sel) {
- out_be32(&lbc->br0, CONFIG_SYS_BR1_PRELIM);
- out_be32(&lbc->or0, CONFIG_SYS_OR1_PRELIM);
+ set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
- out_be32(&lbc->br1, CONFIG_SYS_BR0_PRELIM);
- out_be32(&lbc->or1, CONFIG_SYS_OR0_PRELIM);
+ set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
+ set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
}
}
diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite5370/xpedite5370.c
index 48d9fc8..2a060c2 100644
--- a/board/xes/xpedite5370/xpedite5370.c
+++ b/board/xes/xpedite5370/xpedite5370.c
@@ -58,7 +58,6 @@ int checkboard(void)
static void flash_cs_fixup(void)
{
- volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
int flash_sel;
/*
@@ -71,11 +70,11 @@ static void flash_cs_fixup(void)
printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
if (flash_sel) {
- out_be32(&lbc->br0, CONFIG_SYS_BR1_PRELIM);
- out_be32(&lbc->or0, CONFIG_SYS_OR1_PRELIM);
+ set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
- out_be32(&lbc->br1, CONFIG_SYS_BR0_PRELIM);
- out_be32(&lbc->or1, CONFIG_SYS_OR0_PRELIM);
+ set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
+ set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
}
}
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c
index 146e9bf..acdb431 100644
--- a/drivers/mtd/nand/fsl_elbc_nand.c
+++ b/drivers/mtd/nand/fsl_elbc_nand.c
@@ -75,7 +75,7 @@ struct fsl_elbc_ctrl {
struct fsl_elbc_mtd *chips[MAX_BANKS];
/* device info */
- fsl_lbus_t *regs;
+ fsl_lbc_t *regs;
u8 __iomem *addr; /* Address of assigned FCM buffer */
unsigned int page; /* Last page written to / read from */
unsigned int read_bytes; /* Number of bytes read during command */
@@ -171,7 +171,7 @@ static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob)
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- fsl_lbus_t *lbc = ctrl->regs;
+ fsl_lbc_t *lbc = ctrl->regs;
int buf_num;
ctrl->page = page_addr;
@@ -211,7 +211,7 @@ static int fsl_elbc_run_command(struct mtd_info *mtd)
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- fsl_lbus_t *lbc = ctrl->regs;
+ fsl_lbc_t *lbc = ctrl->regs;
long long end_tick;
u32 ltesr;
@@ -261,7 +261,7 @@ static void fsl_elbc_do_read(struct nand_chip *chip, int oob)
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- fsl_lbus_t *lbc = ctrl->regs;
+ fsl_lbc_t *lbc = ctrl->regs;
if (priv->page_size) {
out_be32(&lbc->fir,
@@ -295,7 +295,7 @@ static void fsl_elbc_cmdfunc(struct mtd_info *mtd, unsigned int command,
struct nand_chip *chip = mtd->priv;
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- fsl_lbus_t *lbc = ctrl->regs;
+ fsl_lbc_t *lbc = ctrl->regs;
ctrl->use_mdr = 0;
@@ -633,7 +633,7 @@ static int fsl_elbc_wait(struct mtd_info *mtd, struct nand_chip *chip)
{
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
- fsl_lbus_t *lbc = ctrl->regs;
+ fsl_lbc_t *lbc = ctrl->regs;
if (ctrl->status != LTESR_CC)
return NAND_STATUS_FAIL;
@@ -697,11 +697,7 @@ static void fsl_elbc_ctrl_init(void)
if (!elbc_ctrl)
return;
-#ifdef CONFIG_MPC85xx
- elbc_ctrl->regs = (void *)CONFIG_SYS_MPC85xx_LBC_ADDR;
-#else
- elbc_ctrl->regs = &((immap_t *)CONFIG_SYS_IMMR)->lbus;
-#endif
+ elbc_ctrl->regs = LBC_BASE_ADDR;
/* clear event registers */
out_be32(&elbc_ctrl->regs->ltesr, LTESR_NAND_MASK);
diff --git a/include/mpc85xx.h b/include/mpc85xx.h
index a4d4d65..2495b99 100644
--- a/include/mpc85xx.h
+++ b/include/mpc85xx.h
@@ -6,8 +6,6 @@
#ifndef __MPC85xx_H__
#define __MPC85xx_H__
-#include <asm/fsl_lbc.h>
-
/* define for common ppc_asm.tmpl */
#define EXC_OFF_SYS_RESET 0x100 /* System reset */
#define _START_OFFSET 0
diff --git a/nand_spl/board/freescale/mpc8536ds/nand_boot.c b/nand_spl/board/freescale/mpc8536ds/nand_boot.c
index af29dc2..5a0a0c7 100644
--- a/nand_spl/board/freescale/mpc8536ds/nand_boot.c
+++ b/nand_spl/board/freescale/mpc8536ds/nand_boot.c
@@ -34,12 +34,11 @@ void board_init_f(ulong bootflag)
int px_spd;
u32 plat_ratio, bus_clk, sys_clk;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
- ccsr_lbc_t *lbc = (void *)CONFIG_SYS_MPC85xx_LBC_ADDR;
#if defined(CONFIG_SYS_BR3_PRELIM) && defined(CONFIG_SYS_OR3_PRELIM)
/* for FPGA */
- out_be32(&lbc->br3, CONFIG_SYS_BR3_PRELIM);
- out_be32(&lbc->or3, CONFIG_SYS_OR3_PRELIM);
+ set_lbc_br(3, CONFIG_SYS_BR3_PRELIM);
+ set_lbc_or(3, CONFIG_SYS_OR3_PRELIM);
#else
#error CONFIG_SYS_BR3_PRELIM, CONFIG_SYS_OR3_PRELIM must be defined
#endif
diff --git a/nand_spl/nand_boot_fsl_elbc.c b/nand_spl/nand_boot_fsl_elbc.c
index ff47d55..9547d44 100644
--- a/nand_spl/nand_boot_fsl_elbc.c
+++ b/nand_spl/nand_boot_fsl_elbc.c
@@ -32,7 +32,7 @@
static void nand_wait(void)
{
- fsl_lbus_t *regs = (fsl_lbus_t *)(CONFIG_SYS_IMMR + 0x5000);
+ fsl_lbc_t *regs = LBC_BASE_ADDR;
for (;;) {
uint32_t status = in_be32(®s->ltesr);
@@ -49,7 +49,7 @@ static void nand_wait(void)
static void nand_load(unsigned int offs, int uboot_size, uchar *dst)
{
- fsl_lbus_t *regs = (fsl_lbus_t *)(CONFIG_SYS_IMMR + 0x5000);
+ fsl_lbc_t *regs = LBC_BASE_ADDR;
uchar *buf = (uchar *)CONFIG_SYS_NAND_BASE;
int large = in_be32(®s->bank[0].or) & OR_FCM_PGS;
int block_shift = large ? 17 : 14;
--
1.6.0.6
More information about the U-Boot
mailing list