[U-Boot] [RFC][PATCH 03/21] [x86] Fix MMCR Access
Graeme Russ
graeme.russ at gmail.com
Thu Mar 25 12:22:45 CET 2010
Change sc520 MMCR Access to use memory accessor functions
---
board/eNET/eNET.c | 86 +++++++++++++++++++++---------------------
cpu/i386/sc520/sc520.c | 33 +++++++++-------
cpu/i386/sc520/sc520_pci.c | 24 +++++++----
cpu/i386/sc520/sc520_ssi.c | 27 +++++++------
cpu/i386/sc520/sc520_timer.c | 31 ++++++++-------
5 files changed, 106 insertions(+), 95 deletions(-)
diff --git a/board/eNET/eNET.c b/board/eNET/eNET.c
index 6d0b15a..f794beb 100644
--- a/board/eNET/eNET.c
+++ b/board/eNET/eNET.c
@@ -46,7 +46,7 @@ unsigned long monitor_flash_len = CONFIG_SYS_MONITOR_LEN;
void init_sc520_enet (void)
{
/* Set CPU Speed to 100MHz */
- sc520_mmcr->cpuctl = 0x01;
+ writeb(0x01, &sc520_mmcr->cpuctl);
/* wait at least one millisecond */
asm("movl $0x2000,%%ecx\n"
@@ -55,7 +55,7 @@ void init_sc520_enet (void)
"loop 0b\n": : : "ecx");
/* turn on the SDRAM write buffer */
- sc520_mmcr->dbctl = 0x11;
+ writeb(0x11, &sc520_mmcr->dbctl);
/* turn on the cache and disable write through */
asm("movl %%cr0, %%eax\n"
@@ -70,51 +70,51 @@ int board_early_init_f(void)
{
init_sc520_enet();
- sc520_mmcr->gpcsrt = 0x01; /* GP Chip Select Recovery Time */
- sc520_mmcr->gpcspw = 0x07; /* GP Chip Select Pulse Width */
- sc520_mmcr->gpcsoff = 0x00; /* GP Chip Select Offset */
- sc520_mmcr->gprdw = 0x05; /* GP Read pulse width */
- sc520_mmcr->gprdoff = 0x01; /* GP Read offset */
- sc520_mmcr->gpwrw = 0x05; /* GP Write pulse width */
- sc520_mmcr->gpwroff = 0x01; /* GP Write offset */
-
- sc520_mmcr->piodata15_0 = 0x0630; /* PIO15_PIO0 Data */
- sc520_mmcr->piodata31_16 = 0x2000; /* PIO31_PIO16 Data */
- sc520_mmcr->piodir31_16 = 0x2000; /* GPIO Direction */
- sc520_mmcr->piodir15_0 = 0x87b5; /* GPIO Direction */
- sc520_mmcr->piopfs31_16 = 0x0dfe; /* GPIO pin function 31-16 reg */
- sc520_mmcr->piopfs15_0 = 0x200a; /* GPIO pin function 15-0 reg */
- sc520_mmcr->cspfs = 0x00f8; /* Chip Select Pin Function Select */
-
- sc520_mmcr->par[2] = 0x200713f8; /* Uart A (GPCS0, 0x013f8, 8 Bytes) */
- sc520_mmcr->par[3] = 0x2c0712f8; /* Uart B (GPCS3, 0x012f8, 8 Bytes) */
- sc520_mmcr->par[4] = 0x300711f8; /* Uart C (GPCS4, 0x011f8, 8 Bytes) */
- sc520_mmcr->par[5] = 0x340710f8; /* Uart D (GPCS5, 0x010f8, 8 Bytes) */
- sc520_mmcr->par[6] = 0xe3ffc000; /* SDRAM (0x00000000, 128MB) */
- sc520_mmcr->par[7] = 0xaa3fd000; /* StrataFlash (ROMCS1, 0x10000000, 16MB) */
- sc520_mmcr->par[8] = 0xca3fd100; /* StrataFlash (ROMCS2, 0x11000000, 16MB) */
- sc520_mmcr->par[9] = 0x4203d900; /* SRAM (GPCS0, 0x19000000, 1MB) */
- sc520_mmcr->par[10] = 0x4e03d910; /* SRAM (GPCS3, 0x19100000, 1MB) */
- sc520_mmcr->par[11] = 0x50018100; /* DP-RAM (GPCS4, 0x18100000, 4kB) */
- sc520_mmcr->par[12] = 0x54020000; /* CFLASH1 (0x200000000, 4kB) */
- sc520_mmcr->par[13] = 0x5c020001; /* CFLASH2 (0x200010000, 4kB) */
-/* sc520_mmcr->par14 = 0x8bfff800; */ /* BOOTCS at 0x18000000 */
-/* sc520_mmcr->par15 = 0x38201000; */ /* LEDs etc (GPCS6, 0x1000, 20 Bytes */
+ writeb(0x01, &sc520_mmcr->gpcsrt); /* GP Chip Select Recovery Time */
+ writeb(0x07, &sc520_mmcr->gpcspw); /* GP Chip Select Pulse Width */
+ writeb(0x00, &sc520_mmcr->gpcsoff); /* GP Chip Select Offset */
+ writeb(0x05, &sc520_mmcr->gprdw); /* GP Read pulse width */
+ writeb(0x01, &sc520_mmcr->gprdoff); /* GP Read offset */
+ writeb(0x05, &sc520_mmcr->gpwrw); /* GP Write pulse width */
+ writeb(0x01, &sc520_mmcr->gpwroff); /* GP Write offset */
+
+ writew(0x0630, &sc520_mmcr->piodata15_0); /* PIO15_PIO0 Data */
+ writew(0x2000, &sc520_mmcr->piodata31_16); /* PIO31_PIO16 Data */
+ writew(0x2000, &sc520_mmcr->piodir31_16); /* GPIO Direction */
+ writew(0x87b5, &sc520_mmcr->piodir15_0); /* GPIO Direction */
+ writew(0x0dfe, &sc520_mmcr->piopfs31_16); /* GPIO pin function 31-16 reg */
+ writew(0x200a, &sc520_mmcr->piopfs15_0); /* GPIO pin function 15-0 reg */
+ writeb(0xf8, &sc520_mmcr->cspfs); /* Chip Select Pin Function Select */
+
+ writel(0x200713f8, &sc520_mmcr->par[2]); /* Uart A (GPCS0, 0x013f8, 8 Bytes) */
+ writel(0x2c0712f8, &sc520_mmcr->par[3]); /* Uart B (GPCS3, 0x012f8, 8 Bytes) */
+ writel(0x300711f8, &sc520_mmcr->par[4]); /* Uart C (GPCS4, 0x011f8, 8 Bytes) */
+ writel(0x340710f8, &sc520_mmcr->par[5]); /* Uart D (GPCS5, 0x010f8, 8 Bytes) */
+ writel(0xe3ffc000, &sc520_mmcr->par[6]); /* SDRAM (0x00000000, 128MB) */
+ writel(0xaa3fd000, &sc520_mmcr->par[7]); /* StrataFlash (ROMCS1, 0x10000000, 16MB) */
+ writel(0xca3fd100, &sc520_mmcr->par[8]); /* StrataFlash (ROMCS2, 0x11000000, 16MB) */
+ writel(0x4203d900, &sc520_mmcr->par[9]); /* SRAM (GPCS0, 0x19000000, 1MB) */
+ writel(0x4e03d910, &sc520_mmcr->par[10]); /* SRAM (GPCS3, 0x19100000, 1MB) */
+ writel(0x50018100, &sc520_mmcr->par[11]); /* DP-RAM (GPCS4, 0x18100000, 4kB) */
+ writel(0x54020000, &sc520_mmcr->par[12]); /* CFLASH1 (0x200000000, 4kB) */
+ writel(0x5c020001, &sc520_mmcr->par[13]); /* CFLASH2 (0x200010000, 4kB) */
+/* writel(0x8bfff800, &sc520_mmcr->par14); */ /* BOOTCS at 0x18000000 */
+/* writel(0x38201000, &sc520_mmcr->par15); */ /* LEDs etc (GPCS6, 0x1000, 20 Bytes */
/* Disable Watchdog */
- sc520_mmcr->wdtmrctl = 0x3333;
- sc520_mmcr->wdtmrctl = 0xcccc;
- sc520_mmcr->wdtmrctl = 0x0000;
+ writew(0x3333, &sc520_mmcr->wdtmrctl);
+ writew(0xcccc, &sc520_mmcr->wdtmrctl);
+ writew(0x0000, &sc520_mmcr->wdtmrctl);
/* Chip Select Configuration */
- sc520_mmcr->bootcsctl = 0x0033;
- sc520_mmcr->romcs1ctl = 0x0615;
- sc520_mmcr->romcs2ctl = 0x0615;
-
- sc520_mmcr->adddecctl = 0x02;
- sc520_mmcr->uart1ctl = 0x07;
- sc520_mmcr->sysarbctl = 0x06;
- sc520_mmcr->sysarbmenb = 0x0003;
+ writew(0x0033, &sc520_mmcr->bootcsctl);
+ writew(0x0615, &sc520_mmcr->romcs1ctl);
+ writew(0x0615, &sc520_mmcr->romcs2ctl);
+
+ writeb(0x02, &sc520_mmcr->adddecctl);
+ writeb(0x07, &sc520_mmcr->uart1ctl);
+ writeb(0x06, &sc520_mmcr->sysarbctl);
+ writew(0x0003, &sc520_mmcr->sysarbmenb);
return 0;
}
diff --git a/cpu/i386/sc520/sc520.c b/cpu/i386/sc520/sc520.c
index 4b566a7..519bfd8 100644
--- a/cpu/i386/sc520/sc520.c
+++ b/cpu/i386/sc520/sc520.c
@@ -44,24 +44,24 @@ void init_sc520(void)
/* Set the UARTxCTL register at it's slower,
* baud clock giving us a 1.8432 MHz reference
*/
- sc520_mmcr->uart1ctl = 0x07;
- sc520_mmcr->uart2ctl = 0x07;
+ writeb(0x07, &sc520_mmcr->uart1ctl);
+ writeb(0x07, &sc520_mmcr->uart2ctl);
/* first set the timer pin mapping */
- sc520_mmcr->clksel = 0x72; /* no clock frequency selected, use 1.1892MHz */
+ writeb(0x72, &sc520_mmcr->clksel); /* no clock frequency selected, use 1.1892MHz */
/* enable PCI bus arbitrer */
- sc520_mmcr->sysarbctl = 0x02; /* enable concurrent mode */
+ writeb(0x02, &sc520_mmcr->sysarbctl); /* enable concurrent mode */
- sc520_mmcr->sysarbmenb = 0x1f; /* enable external grants */
- sc520_mmcr->hbctl = 0x04; /* enable posted-writes */
+ writeb(0x1f, &sc520_mmcr->sysarbmenb); /* enable external grants */
+ writeb(0x04, &sc520_mmcr->hbctl); /* enable posted-writes */
if (CONFIG_SYS_SC520_HIGH_SPEED) {
- sc520_mmcr->cpuctl = 0x02; /* set it to 133 MHz and write back */
+ writeb(0x02, &sc520_mmcr->cpuctl); /* set it to 133 MHz and write back */
gd->cpu_clk = 133000000;
printf("## CPU Speed set to 133MHz\n");
} else {
- sc520_mmcr->cpuctl = 0x01; /* set it to 100 MHz and write back */
+ writeb(0x01, &sc520_mmcr->cpuctl); /* set it to 100 MHz and write back */
printf("## CPU Speed set to 100MHz\n");
gd->cpu_clk = 100000000;
}
@@ -74,7 +74,7 @@ void init_sc520(void)
"loop 0b\n": : : "ecx");
/* turn on the SDRAM write buffer */
- sc520_mmcr->dbctl = 0x11;
+ writeb(0x11, &sc520_mmcr->dbctl);
/* turn on the cache and disable write through */
asm("movl %%cr0, %%eax\n"
@@ -88,6 +88,7 @@ unsigned long init_sc520_dram(void)
u32 dram_present=0;
u32 dram_ctrl;
+
#ifdef CONFIG_SYS_SDRAM_DRCTMCTL
/* these memory control registers are set up in the assember part,
* in sc520_asm.S, during 'mem_init'. If we muck with them here,
@@ -97,7 +98,8 @@ unsigned long init_sc520_dram(void)
* simply dictates it.
*/
#else
- int val;
+ u8 tmp;
+ u8 val;
int cas_precharge_delay = CONFIG_SYS_SDRAM_PRECHARGE_DELAY;
int refresh_rate = CONFIG_SYS_SDRAM_REFRESH_RATE;
@@ -116,9 +118,10 @@ unsigned long init_sc520_dram(void)
val = 3; /* 62.4us */
}
- sc520_mmcr->drcctl = (sc520_mmcr->drcctl & 0xcf) | (val<<4);
+ tmp = (readb(&sc520_mmcr->drcctl) & 0xcf) | (val<<4);
+ writeb(tmp, &sc520_mmcr->drcctl);
- val = sc520_mmcr->drctmctl & 0xf0;
+ val = readb(&sc520_mmcr->drctmctl) & 0xf0;
if (cas_precharge_delay==3) {
val |= 0x04; /* 3T */
@@ -133,12 +136,12 @@ unsigned long init_sc520_dram(void)
} else {
val |= 1;
}
- sc520_mmcr->drctmctl = val;
+ writeb(val, &c520_mmcr->drctmctl);
#endif
/* We read-back the configuration of the dram
* controller that the assembly code wrote */
- dram_ctrl = sc520_mmcr->drcbendadr;
+ dram_ctrl = readl(&sc520_mmcr->drcbendadr);
bd->bi_dram[0].start = 0;
if (dram_ctrl & 0x80) {
@@ -191,7 +194,7 @@ void reset_cpu(ulong addr)
{
printf("Resetting using SC520 MMCR\n");
/* Write a '1' to the SYS_RST of the RESCFG MMCR */
- sc520_mmcr->rescfg = 0x01;
+ writeb(0x01, &sc520_mmcr->rescfg);
/* NOTREACHED */
}
diff --git a/cpu/i386/sc520/sc520_pci.c b/cpu/i386/sc520/sc520_pci.c
index f446c6d..ee7e720 100644
--- a/cpu/i386/sc520/sc520_pci.c
+++ b/cpu/i386/sc520/sc520_pci.c
@@ -25,6 +25,7 @@
#include <common.h>
#include <pci.h>
+#include <asm/io.h>
#include <asm/pci.h>
#include <asm/ic/sc520.h>
@@ -63,6 +64,8 @@ int sc520_pci_ints[15] = {
int pci_sc520_set_irq(int pci_pin, int irq)
{
int i;
+ u8 tmpb;
+ u16 tmpw;
# if 1
printf("set_irq(): map INT%c to IRQ%d\n", pci_pin + 'A', irq);
@@ -80,31 +83,34 @@ int pci_sc520_set_irq(int pci_pin, int irq)
/* PCI interrupt mapping (A through D)*/
for (i=0; i<=3 ;i++) {
- if (sc520_mmcr->pci_int_map[i] == sc520_irq[irq].priority)
- sc520_mmcr->pci_int_map[i] = SC520_IRQ_DISABLED;
+ if (readb(&sc520_mmcr->pci_int_map[i]) == sc520_irq[irq].priority)
+ writeb(SC520_IRQ_DISABLED, &sc520_mmcr->pci_int_map[i]);
}
/* GP IRQ interrupt mapping */
for (i=0; i<=10 ;i++) {
- if (sc520_mmcr->gp_int_map[i] == sc520_irq[irq].priority)
- sc520_mmcr->gp_int_map[i] = SC520_IRQ_DISABLED;
+ if (readb(&sc520_mmcr->gp_int_map[i]) == sc520_irq[irq].priority)
+ writeb(SC520_IRQ_DISABLED, &sc520_mmcr->gp_int_map[i]);
}
/* Set the trigger to level */
- sc520_mmcr->pic_mode[sc520_irq[irq].level_reg] =
- sc520_mmcr->pic_mode[sc520_irq[irq].level_reg] | sc520_irq[irq].level_bit;
+ tmpb = readb(&sc520_mmcr->pic_mode[sc520_irq[irq].level_reg]);
+ tmpb |= sc520_irq[irq].level_bit;
+ writeb(tmpb, &sc520_mmcr->pic_mode[sc520_irq[irq].level_reg]);
if (pci_pin < 4) {
/* PCI INTA-INTD */
/* route the interrupt */
- sc520_mmcr->pci_int_map[pci_pin] = sc520_irq[irq].priority;
+ writeb(sc520_irq[irq].priority, &sc520_mmcr->pci_int_map[pci_pin]);
} else {
/* GPIRQ0-GPIRQ10 used for additional PCI INTS */
- sc520_mmcr->gp_int_map[pci_pin - 4] = sc520_irq[irq].priority;
+ writeb(sc520_irq[irq].priority, &sc520_mmcr->gp_int_map[pci_pin - 4]);
/* also set the polarity in this case */
- sc520_mmcr->intpinpol = sc520_mmcr->intpinpol | (1 << (pci_pin-4));
+ tmpw = readw(&sc520_mmcr->intpinpol);
+ tmpw |= (1 << (pci_pin-4));
+ writew(tmpw, &sc520_mmcr->intpinpol);
}
/* register the pin */
diff --git a/cpu/i386/sc520/sc520_ssi.c b/cpu/i386/sc520/sc520_ssi.c
index 8dbe17a..6e5e346 100644
--- a/cpu/i386/sc520/sc520_ssi.c
+++ b/cpu/i386/sc520/sc520_ssi.c
@@ -24,6 +24,7 @@
/* stuff specific for the sc520, but independent of implementation */
#include <common.h>
+#include <asm/io.h>
#include <asm/ic/ssi.h>
#include <asm/ic/sc520.h>
@@ -61,34 +62,34 @@ int ssi_set_interface(int freq, int lsb_first, int inv_clock, int inv_phase)
temp |= PHS_INV_ENB;
}
- sc520_mmcr->ssictl = temp;
+ writeb(temp, &sc520_mmcr->ssictl);
return 0;
}
u8 ssi_txrx_byte(u8 data)
{
- sc520_mmcr->ssixmit = data;
- while (sc520_mmcr->ssista & SSISTA_BSY);
- sc520_mmcr->ssicmd = SSICMD_CMD_SEL_XMITRCV;
- while (sc520_mmcr->ssista & SSISTA_BSY);
+ writeb(data, &sc520_mmcr->ssixmit);
+ while (readb(&sc520_mmcr->ssista) & SSISTA_BSY);
+ writeb(SSICMD_CMD_SEL_XMITRCV, &sc520_mmcr->ssicmd);
+ while (readb(&sc520_mmcr->ssista) & SSISTA_BSY);
- return sc520_mmcr->ssircv;
+ return readb(&sc520_mmcr->ssircv);
}
void ssi_tx_byte(u8 data)
{
- sc520_mmcr->ssixmit = data;
- while (sc520_mmcr->ssista & SSISTA_BSY);
- sc520_mmcr->ssicmd = SSICMD_CMD_SEL_XMIT;
+ writeb(data, &sc520_mmcr->ssixmit);
+ while (readb(&sc520_mmcr->ssista) & SSISTA_BSY);
+ writeb(SSICMD_CMD_SEL_XMIT, &sc520_mmcr->ssicmd);
}
u8 ssi_rx_byte(void)
{
- while (sc520_mmcr->ssista & SSISTA_BSY);
- sc520_mmcr->ssicmd = SSICMD_CMD_SEL_RCV;
- while (sc520_mmcr->ssista & SSISTA_BSY);
+ while (readb(&sc520_mmcr->ssista) & SSISTA_BSY);
+ writeb(SSICMD_CMD_SEL_RCV, &sc520_mmcr->ssicmd);
+ while (readb(&sc520_mmcr->ssista) & SSISTA_BSY);
- return sc520_mmcr->ssircv;
+ return readb(&sc520_mmcr->ssircv);
}
diff --git a/cpu/i386/sc520/sc520_timer.c b/cpu/i386/sc520/sc520_timer.c
index 93b5b55..eca48e0 100644
--- a/cpu/i386/sc520/sc520_timer.c
+++ b/cpu/i386/sc520/sc520_timer.c
@@ -24,13 +24,14 @@
/* stuff specific for the sc520, but independent of implementation */
#include <common.h>
+#include <asm/io.h>
#include <asm/interrupt.h>
#include <asm/ic/sc520.h>
void sc520_timer_isr(void)
{
/* Ack the GP Timer Interrupt */
- sc520_mmcr->gptmrsta = 0x02;
+ writeb(0x02, &sc520_mmcr->gptmrsta);
}
int timer_init(void)
@@ -42,28 +43,28 @@ int timer_init(void)
irq_install_handler (0, timer_isr, NULL);
/* Map GP Timer 1 to Master PIC IR0 */
- sc520_mmcr->gp_tmr_int_map[1] = 0x01;
+ writeb(0x01, &sc520_mmcr->gp_tmr_int_map[1]);
/* Disable GP Timers 1 & 2 - Allow configuration writes */
- sc520_mmcr->gptmr1ctl = 0x4000;
- sc520_mmcr->gptmr2ctl = 0x4000;
+ writew(0x4000, &sc520_mmcr->gptmr1ctl);
+ writew(0x4000, &sc520_mmcr->gptmr2ctl);
/* Reset GP Timers 1 & 2 */
- sc520_mmcr->gptmr1cnt = 0x0000;
- sc520_mmcr->gptmr2cnt = 0x0000;
+ writew(0x0000, &sc520_mmcr->gptmr1cnt);
+ writew(0x0000, &sc520_mmcr->gptmr2cnt);
/* Setup GP Timer 2 as a 100kHz (10us) prescaler */
- sc520_mmcr->gptmr2maxcmpa = 83;
- sc520_mmcr->gptmr2ctl = 0xc001;
+ writew(83, &sc520_mmcr->gptmr2maxcmpa);
+ writew(0xc001, &sc520_mmcr->gptmr2ctl);
/* Setup GP Timer 1 as a 1000 Hz (1ms) interrupt generator */
- sc520_mmcr->gptmr1maxcmpa = 100;
- sc520_mmcr->gptmr1ctl = 0xe009;
+ writew(100, &sc520_mmcr->gptmr1maxcmpa);
+ writew(0xe009, &sc520_mmcr->gptmr1ctl);
unmask_irq (0);
/* Clear the GP Timer 1 status register to get the show rolling*/
- sc520_mmcr->gptmrsta = 0x02;
+ writeb(0x02, &sc520_mmcr->gptmrsta);
return 0;
}
@@ -74,11 +75,11 @@ void __udelay(unsigned long usec)
long u;
long temp;
- temp = sc520_mmcr->swtmrmilli;
- temp = sc520_mmcr->swtmrmicro;
+ temp = readw(&sc520_mmcr->swtmrmilli);
+ temp = readw(&sc520_mmcr->swtmrmicro);
do {
- m += sc520_mmcr->swtmrmilli;
- u = sc520_mmcr->swtmrmicro + (m * 1000);
+ m += readw(&sc520_mmcr->swtmrmilli);
+ u = readw(&sc520_mmcr->swtmrmicro) + (m * 1000);
} while (u < usec);
}
--
1.7.0.2.182.ge007
More information about the U-Boot
mailing list