[U-Boot] [PATCH 3/3 v6] mmc: add generic mmc spi driver
Thomas Chou
thomas at wytron.com.tw
Mon May 3 02:54:45 CEST 2010
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports write.
The crc checksum on data packet is enabled with the def,
#define CONFIG_MMC_SPI_CRC_ON
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas at wytron.com.tw>
---
v6: add constant macros, crc check on data, per Andy.
v5: remove dev_num limit to search.
v4: change mmc_spi subcommand to search and create new mmc dev.
v3: add mmc_spi_init() proto to mmc_spi.h.
v2: add crc7, use cmd58 to read ocr, add subcommand mmc_spi.
common/Makefile | 1 +
common/cmd_mmc_spi.c | 115 ++++++++++++++
drivers/mmc/Makefile | 1 +
drivers/mmc/mmc_spi.c | 393 +++++++++++++++++++++++++++++++++++++++++++++++++
include/mmc_spi.h | 27 ++++
5 files changed, 537 insertions(+), 0 deletions(-)
create mode 100644 common/cmd_mmc_spi.c
create mode 100644 drivers/mmc/mmc_spi.c
create mode 100644 include/mmc_spi.h
diff --git a/common/Makefile b/common/Makefile
index dbf7a05..ee23e2f 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -118,6 +118,7 @@ COBJS-$(CONFIG_CMD_MII) += miiphyutil.o
COBJS-$(CONFIG_CMD_MII) += cmd_mii.o
COBJS-$(CONFIG_CMD_MISC) += cmd_misc.o
COBJS-$(CONFIG_CMD_MMC) += cmd_mmc.o
+COBJS-$(CONFIG_CMD_MMC_SPI) += cmd_mmc_spi.o
COBJS-$(CONFIG_MP) += cmd_mp.o
COBJS-$(CONFIG_CMD_MTDPARTS) += cmd_mtdparts.o
COBJS-$(CONFIG_CMD_NAND) += cmd_nand.o
diff --git a/common/cmd_mmc_spi.c b/common/cmd_mmc_spi.c
new file mode 100644
index 0000000..8affa02
--- /dev/null
+++ b/common/cmd_mmc_spi.c
@@ -0,0 +1,115 @@
+/*
+ * Command for mmc_spi setup.
+ *
+ * Copyright (C) 2010 Thomas Chou <thomas at wytron.com.tw>
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <spi.h>
+#include <mmc_spi.h>
+
+#ifndef CONFIG_MMC_SPI_BUS
+# define CONFIG_MMC_SPI_BUS 0
+#endif
+#ifndef CONFIG_MMC_SPI_CS
+# define CONFIG_MMC_SPI_CS 1
+#endif
+#ifndef CONFIG_MMC_SPI_SPEED
+# define CONFIG_MMC_SPI_SPEED 30000000
+#endif
+#ifndef CONFIG_MMC_SPI_MODE
+# define CONFIG_MMC_SPI_MODE SPI_MODE_3
+#endif
+
+static void print_mmc_spi(struct mmc *mmc)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ printf("%s: %d at %u:%u %u %u\n", mmc->name, mmc->block_dev.dev,
+ priv->bus, priv->cs, priv->speed, priv->mode);
+}
+
+static int do_mmc_spi(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int dev_num = -1;
+ uint bus = CONFIG_MMC_SPI_BUS;
+ uint cs = CONFIG_MMC_SPI_CS;
+ uint speed = CONFIG_MMC_SPI_SPEED;
+ uint mode = CONFIG_MMC_SPI_MODE;
+ char *endp;
+ struct mmc *mmc;
+ struct mmc_spi_priv *priv;
+
+ if (argc < 2) {
+ while (1) {
+ mmc = find_mmc_device_quiet(++dev_num);
+ if (!mmc)
+ break;
+ if (strcmp(mmc->name, "MMC_SPI") == 0)
+ print_mmc_spi(mmc);
+ }
+ return 0;
+ }
+
+ cs = simple_strtoul(argv[1], &endp, 0);
+ if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
+ goto usage;
+ if (*endp == ':') {
+ if (endp[1] == 0)
+ goto usage;
+ bus = cs;
+ cs = simple_strtoul(endp + 1, &endp, 0);
+ if (*endp != 0)
+ goto usage;
+ }
+ if (argc >= 3) {
+ speed = simple_strtoul(argv[2], &endp, 0);
+ if (*argv[2] == 0 || *endp != 0)
+ goto usage;
+ }
+ if (argc >= 4) {
+ mode = simple_strtoul(argv[3], &endp, 16);
+ if (*argv[3] == 0 || *endp != 0)
+ goto usage;
+ }
+ if (!spi_cs_is_valid(bus, cs)) {
+ printf("Invalid SPI bus %u cs %u\n", bus, cs);
+ return 1;
+ }
+
+ while (1) {
+ mmc = find_mmc_device_quiet(++dev_num);
+ if (!mmc)
+ break;
+ if (strcmp(mmc->name, "MMC_SPI") == 0) {
+ priv = mmc->priv;
+ if (priv->bus == bus && priv->cs == cs) {
+ printf("SPI bus and cs in use\n");
+ print_mmc_spi(mmc);
+ return 1;
+ }
+ }
+ }
+
+ printf("Create MMC Device\n");
+ mmc = mmc_spi_init(bus, cs, speed, mode);
+ if (!mmc) {
+ printf("Failed to create MMC Device\n");
+ return 1;
+ }
+ print_mmc_spi(mmc);
+ return 0;
+
+usage:
+ cmd_usage(cmdtp);
+ return 1;
+}
+
+U_BOOT_CMD(
+ mmc_spi, 4, 0, do_mmc_spi,
+ "mmc_spi setup",
+ "[bus:][cs] [hz] [mode] - setup mmc_spi device on given\n"
+ " SPI bus and chip select\n"
+);
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 6fa04b8..02ed329 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -28,6 +28,7 @@ LIB := $(obj)libmmc.a
COBJS-$(CONFIG_GENERIC_MMC) += mmc.o
COBJS-$(CONFIG_ATMEL_MCI) += atmel_mci.o
COBJS-$(CONFIG_BFIN_SDH) += bfin_sdh.o
+COBJS-$(CONFIG_MMC_SPI) += mmc_spi.o
COBJS-$(CONFIG_OMAP3_MMC) += omap3_mmc.o
COBJS-$(CONFIG_FSL_ESDHC) += fsl_esdhc.o
COBJS-$(CONFIG_MXC_MMC) += mxcmmc.o
diff --git a/drivers/mmc/mmc_spi.c b/drivers/mmc/mmc_spi.c
new file mode 100644
index 0000000..b601941
--- /dev/null
+++ b/drivers/mmc/mmc_spi.c
@@ -0,0 +1,393 @@
+/*
+ * generic mmc spi driver
+ *
+ * Copyright (C) 2010 Thomas Chou <thomas at wytron.com.tw>
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <part.h>
+#include <mmc.h>
+#include <spi.h>
+#include <mmc_spi.h>
+#include <crc.h>
+#include <linux/crc7.h>
+#include <asm/errno.h>
+
+/* Standard MMC commands (4.1) type argument response */
+#define MMC_SPI_READ_OCR 58 /* spi spi_R3 */
+#define MMC_SPI_CRC_ON_OFF 59 /* spi [0:0] flag spi_R1 */
+
+/*
+ * MMC/SD in SPI mode reports R1 status always
+ */
+#define R1_SPI_IDLE (1 << 0)
+#define R1_SPI_ERASE_RESET (1 << 1)
+#define R1_SPI_ILLEGAL_COMMAND (1 << 2)
+#define R1_SPI_COM_CRC (1 << 3)
+#define R1_SPI_ERASE_SEQ (1 << 4)
+#define R1_SPI_ADDRESS (1 << 5)
+#define R1_SPI_PARAMETER (1 << 6)
+/* R1 bit 7 is always zero */
+#define R1_SPI_ERROR (1 << 7)
+
+/* Response tokens used to ack each block written: */
+#define SPI_MMC_RESPONSE_CODE(x) ((x) & 0x1f)
+#define SPI_RESPONSE_ACCEPTED ((2 << 1)|1)
+#define SPI_RESPONSE_CRC_ERR ((5 << 1)|1)
+#define SPI_RESPONSE_WRITE_ERR ((6 << 1)|1)
+
+/* Read and write blocks start with these tokens and end with crc;
+ * on error, read tokens act like a subset of R2_SPI_* values.
+ */
+#define SPI_TOKEN_SINGLE 0xfe /* single block r/w, multiblock read */
+#define SPI_TOKEN_MULTI_WRITE 0xfc /* multiblock write */
+#define SPI_TOKEN_STOP_TRAN 0xfd /* terminate multiblock write */
+
+/* MMC SPI commands start with a start bit "0" and a transmit bit "1" */
+#define MMC_SPI_CMD(x) (0x40 | (x & 0x3f))
+
+/* bus capability */
+#define MMC_SPI_VOLTAGE (MMC_VDD_32_33 | MMC_VDD_33_34)
+#define MMC_SPI_MIN_CLOCK 400000 /* 400KHz to meet MMC spec */
+
+/* timeout value */
+#define CTOUT 0x10
+#define RTOUT 0x10000
+#define WTOUT 0x10000
+
+static uint mmc_spi_sendcmd(struct mmc *mmc, u8 cmdidx, u32 cmdarg)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ u8 cmdo[7];
+ u8 r1;
+ int i;
+ cmdo[0] = 0xff;
+ cmdo[1] = MMC_SPI_CMD(cmdidx);
+ cmdo[2] = cmdarg >> 24;
+ cmdo[3] = cmdarg >> 16;
+ cmdo[4] = cmdarg >> 8;
+ cmdo[5] = cmdarg;
+ cmdo[6] = (crc7(0, &cmdo[1], 5) << 1) | 0x01;
+ spi_xfer(priv->slave, 7 * 8, cmdo, NULL, SPI_XFER_BEGIN);
+ for (i = 0; i < CTOUT; i++) {
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if ((r1 & 0x80) == 0) /* r1 response */
+ break;
+ }
+ debug("%s:cmd%d resp%d %x\n", __func__, cmdidx, i, r1);
+ return r1;
+}
+
+static uint mmc_spi_readdata(struct mmc *mmc, char *buf,
+ u32 bcnt, u32 bsize)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ u8 tok;
+ u8 crc[2];
+ int i;
+ while (bcnt--) {
+ for (i = 0; i < RTOUT; i++) {
+ spi_xfer(priv->slave, 1 * 8, NULL, &tok, 0);
+ if (tok != 0xff)
+ break;
+ }
+ debug("%s:tok%d %x\n", __func__, i, tok);
+ if (tok == SPI_TOKEN_SINGLE) {
+ spi_xfer(priv->slave, bsize * 8, NULL, buf, 0);
+ spi_xfer(priv->slave, 2 * 8, NULL, crc, 0);
+#ifdef CONFIG_MMC_SPI_CRC_ON
+ if (cyg_crc16((unsigned char *)buf, bsize) !=
+ ((crc[0] << 8) | crc[1])) {
+ printf("%s: Readdata CRC error\n", mmc->name);
+ tok = R1_SPI_COM_CRC;
+ break;
+ }
+#endif
+ tok = 0;
+ } else {
+ tok = R1_SPI_ERROR;
+ break;
+ }
+ buf += bsize;
+ }
+ return tok;
+}
+
+static uint mmc_spi_writedata(struct mmc *mmc, const char *buf,
+ u32 bcnt, u32 bsize)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ u8 r1;
+ u8 tok[2] = {0xff, SPI_TOKEN_SINGLE};
+ u8 crc[2];
+ int i;
+ while (bcnt--) {
+#ifdef CONFIG_MMC_SPI_CRC_ON
+ u16 cks;
+ cks = cyg_crc16((unsigned char *)buf, bsize);
+ crc[0] = cks >> 8;
+ crc[1] = cks;
+#endif
+ spi_xfer(priv->slave, 2 * 8, tok, NULL, 0);
+ spi_xfer(priv->slave, bsize * 8, buf, NULL, 0);
+ spi_xfer(priv->slave, 2 * 8, crc, NULL, 0);
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if (SPI_MMC_RESPONSE_CODE(r1) == SPI_RESPONSE_ACCEPTED) {
+ for (i = 0; i < WTOUT; i++) { /* wait busy */
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if (r1 == 0xff) {
+ r1 = 0;
+ break;
+ }
+ }
+ if (i == WTOUT) {
+ debug("%s:wtout %x\n", __func__, r1);
+ r1 = R1_SPI_ERROR;
+ break;
+ }
+ } else {
+ debug("%s: err %x\n", __func__, r1);
+ r1 = R1_SPI_COM_CRC;
+ break;
+ }
+ buf += bsize;
+ }
+ return r1;
+}
+
+static uint mmc_spi_writeblock(struct mmc *mmc, const char *buf,
+ u32 bcnt, u32 bsize)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ u8 r1;
+ u8 tok[2] = {0xff, SPI_TOKEN_MULTI_WRITE};
+ u8 stop[2] = {0xff, SPI_TOKEN_STOP_TRAN};
+ u8 crc[2];
+ int i;
+ while (bcnt--) {
+#ifdef CONFIG_MMC_SPI_CRC_ON
+ u16 cks;
+ cks = cyg_crc16((unsigned char *)buf, bsize);
+ crc[0] = cks >> 8;
+ crc[1] = cks;
+#endif
+ spi_xfer(priv->slave, 2 * 8, tok, NULL, 0);
+ spi_xfer(priv->slave, bsize * 8, buf, NULL, 0);
+ spi_xfer(priv->slave, 2 * 8, crc, NULL, 0);
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if (SPI_MMC_RESPONSE_CODE(r1) == SPI_RESPONSE_ACCEPTED) {
+ for (i = 0; i < WTOUT; i++) {
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if (r1 == 0xff) {
+ r1 = 0;
+ break;
+ }
+ }
+ if (i == WTOUT) {
+ debug("%s:wtout %x\n", __func__, r1);
+ r1 = R1_SPI_ERROR;
+ break;
+ }
+ } else {
+ debug("%s: err %x\n", __func__, r1);
+ r1 = R1_SPI_COM_CRC;
+ break;
+ }
+ buf += bsize;
+ }
+ if (bcnt == 0 && r1 == 0) {
+ spi_xfer(priv->slave, 2 * 8, stop, NULL, 0);
+ for (i = 0; i < WTOUT; i++) {
+ spi_xfer(priv->slave, 1 * 8, NULL, &r1, 0);
+ if (r1 == 0xff) {
+ r1 = 0;
+ break;
+ }
+ }
+ if (i == WTOUT) {
+ debug("%s:wtout %x\n", __func__, r1);
+ r1 = R1_SPI_ERROR;
+ }
+ }
+ return r1;
+}
+
+static inline uint rswap(u8 *d)
+{
+ return (d[0] << 24) | (d[1] << 16) | (d[2] << 8) | d[3];
+}
+
+static inline void mmc_spi_deactivate(struct mmc *mmc)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ spi_xfer(priv->slave, 1 * 8, NULL, NULL, SPI_XFER_END);
+ spi_xfer(priv->slave, 1 * 8, NULL, NULL, 0);
+}
+
+static int mmc_spi_request(struct mmc *mmc, struct mmc_cmd *cmd,
+ struct mmc_data *data)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ u8 r1;
+ ushort cmdidx = cmd->cmdidx;
+ uint cmdarg = cmd->cmdarg;
+ u8 resp[16];
+ int i;
+ int ret = 0;
+ debug("%s:cmd%d %x %x %x\n", __func__,
+ cmd->cmdidx, cmd->resp_type, cmd->cmdarg, cmd->flags);
+ if (cmdidx == MMC_CMD_ALL_SEND_CID)
+ cmdidx = MMC_CMD_SEND_CID;
+ r1 = mmc_spi_sendcmd(mmc, cmdidx, cmdarg);
+ if (r1 == 0xff) {
+ ret = NO_CARD_ERR;
+ goto done;
+ } else if (cmd->resp_type == MMC_RSP_R2) {
+ r1 = mmc_spi_readdata(mmc, resp, 1, 16);
+ for (i = 0; i < 4; i++)
+ cmd->response[i] = rswap(resp + i * 4);
+ debug("r128 %x %x %x %x\n", cmd->response[0], cmd->response[1],
+ cmd->response[2], cmd->response[3]);
+ } else {
+ if (!data) {
+ spi_xfer(priv->slave, 4 * 8, NULL, resp, 0);
+ cmd->response[0] = rswap(resp);
+ debug("r32 %x\n", cmd->response[0]);
+ }
+ if (cmdidx == MMC_CMD_GO_IDLE_STATE) {
+ mmc_spi_deactivate(mmc);
+ r1 = mmc_spi_sendcmd(mmc, MMC_SPI_READ_OCR, 0);
+ spi_xfer(priv->slave, 4 * 8,
+ NULL, resp, 0);
+ priv->ocr58 = rswap(resp) & ~OCR_BUSY;
+ debug("ocr58 %x\n", priv->ocr58);
+ } else if (cmdidx == SD_CMD_SEND_IF_COND) {
+ if ((r1 & R1_SPI_ERROR) == 0)
+ priv->sd_if_cond = 1;
+ } else if (cmdidx == SD_CMD_APP_SEND_OP_COND ||
+ cmdidx == MMC_CMD_SEND_OP_COND) {
+ if (r1 & R1_SPI_ILLEGAL_COMMAND)
+ ret = TIMEOUT;
+ else {
+ if (r1 & R1_SPI_IDLE)
+ cmd->response[0] = priv->ocr58;
+ else {
+ mmc_spi_deactivate(mmc);
+ r1 = mmc_spi_sendcmd(mmc,
+ MMC_SPI_READ_OCR, 0);
+ spi_xfer(priv->slave, 4 * 8,
+ NULL, resp, 0);
+ priv->ocr58 = rswap(resp);
+ debug("ocr58 %x\n", priv->ocr58);
+ cmd->response[0] = priv->ocr58;
+#ifdef CONFIG_MMC_SPI_CRC_ON
+ mmc_spi_deactivate(mmc);
+ r1 = mmc_spi_sendcmd(mmc,
+ MMC_SPI_CRC_ON_OFF, 1);
+#endif
+ }
+ }
+ } else {
+ cmd->response[0] = 0;
+ if (r1 & R1_SPI_COM_CRC)
+ ret = COMM_ERR;
+ }
+ }
+ if (data) {
+ debug("%s:data %x %x %x\n", __func__,
+ data->flags, data->blocks, data->blocksize);
+ if (data->flags == MMC_DATA_READ) {
+ r1 = mmc_spi_readdata(mmc, data->dest,
+ data->blocks, data->blocksize);
+ } else if (data->flags == MMC_DATA_WRITE) {
+ if (cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK)
+ r1 = mmc_spi_writeblock(mmc, data->src,
+ data->blocks, data->blocksize);
+ else
+ r1 = mmc_spi_writedata(mmc, data->src,
+ data->blocks, data->blocksize);
+ }
+ if (r1 & R1_SPI_COM_CRC)
+ ret = COMM_ERR;
+ else if (r1)
+ ret = TIMEOUT;
+ }
+done:
+ mmc_spi_deactivate(mmc);
+ return ret;
+}
+
+static void mmc_spi_set_ios(struct mmc *mmc)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ debug("%s: clock %u\n", __func__, mmc->clock);
+ if (mmc->clock && mmc->clock != priv->speed) {
+ /* change clock rate */
+ priv->speed = mmc->clock;
+ spi_claim_bus(priv->slave);
+ }
+}
+
+static int mmc_spi_init_p(struct mmc *mmc)
+{
+ struct mmc_spi_priv *priv = mmc->priv;
+ debug("%s: clock %u\n", __func__, mmc->clock);
+ if (!priv->slave) {
+ debug("%s: setup %u:%u %u %u\n", __func__,
+ priv->bus, priv->cs,
+ priv->speed, priv->mode);
+ priv->slave = spi_setup_slave(priv->bus, priv->cs,
+ priv->speed, priv->mode);
+ if (!priv->slave) {
+ debug("%s: failed to setup spi slave\n", __func__);
+ return -ENOMEM;
+ }
+ }
+ priv->sd_if_cond = 0;
+ priv->ocr58 = 0;
+ /* power on initialization with low speed clock */
+ priv->speed = mmc->f_min;
+ spi_claim_bus(priv->slave);
+ /* finish any pending transfer */
+ spi_xfer(priv->slave, 39 * 8, NULL, NULL,
+ SPI_XFER_BEGIN | SPI_XFER_END);
+ /* cs deactivated for 100+ clock */
+ spi_xfer(priv->slave, 18 * 8, NULL, NULL, 0);
+ return 0;
+}
+
+struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode)
+{
+ struct mmc *mmc;
+ struct mmc_spi_priv *priv;
+
+ mmc = malloc(sizeof(*mmc));
+ if (!mmc)
+ return NULL;
+ priv = malloc(sizeof(*priv));
+ if (!priv) {
+ free(mmc);
+ return NULL;
+ }
+ mmc->priv = priv;
+ priv->bus = bus;
+ priv->cs = cs;
+ priv->speed = speed;
+ priv->mode = mode;
+ sprintf(mmc->name, "MMC_SPI");
+ mmc->send_cmd = mmc_spi_request;
+ mmc->set_ios = mmc_spi_set_ios;
+ mmc->init = mmc_spi_init_p;
+ mmc->host_caps = 0;
+
+ mmc->voltages = MMC_SPI_VOLTAGE;
+ mmc->f_max = speed;
+ mmc->f_min = MMC_SPI_MIN_CLOCK;
+ mmc->block_dev.part_type = PART_TYPE_DOS;
+
+ mmc_register(mmc);
+
+ return mmc;
+}
diff --git a/include/mmc_spi.h b/include/mmc_spi.h
new file mode 100644
index 0000000..fbfa1ce
--- /dev/null
+++ b/include/mmc_spi.h
@@ -0,0 +1,27 @@
+/*
+ * generic mmc spi driver
+ *
+ * Copyright (C) 2010 Thomas Chou <thomas at wytron.com.tw>
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _MMC_SPI_H_
+#define _MMC_SPI_H_
+
+#include <spi.h>
+#include <mmc.h>
+#include <linux/types.h>
+
+struct mmc_spi_priv {
+ struct spi_slave *slave;
+ uint bus;
+ uint cs;
+ uint speed;
+ uint mode;
+ uint ocr58;
+ uint sd_if_cond:1;
+};
+
+struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode);
+
+#endif
--
1.6.6.1
More information about the U-Boot
mailing list