[U-Boot] [PATCH v2 09/13] post/i2c: Rename I2C_ADDR_LIST to CONFIG_SYS_POST_I2C_ADDRS
Peter Tyser
ptyser at xes-inc.com
Fri Oct 22 07:20:30 CEST 2010
Signed-off-by: Peter Tyser <ptyser at xes-inc.com>
CC: hs at denx.de
---
doc/README.POST | 11 ++++-----
include/configs/KUP4K.h | 6 ++--
include/configs/KUP4X.h | 6 ++--
include/configs/TB5200.h | 8 +++---
include/configs/TQM5200.h | 8 +++---
include/configs/cm5200.h | 4 ++-
include/configs/lwmon.h | 50 ++++++++++++++++++++++----------------------
include/configs/lwmon5.h | 15 ++++++-------
include/configs/spieval.h | 8 +++---
post/drivers/i2c.c | 8 +++---
10 files changed, 62 insertions(+), 62 deletions(-)
diff --git a/doc/README.POST b/doc/README.POST
index eeb218d..695497e 100644
--- a/doc/README.POST
+++ b/doc/README.POST
@@ -659,12 +659,11 @@ not need any modifications for porting them to another board/CPU.
2.2.2.1. I2C test
For verifying the I2C bus, a full I2C bus scanning will be performed
-using the i2c_probe() routine. If any I2C device is found, the test
-will be considered as passed, otherwise failed. This particular way
-will be used because it provides the most common method of testing.
-For example, using the internal loopback mode of the CPM I2C
-controller for testing would not work on boards where the software
-I2C driver (also known as bit-banged driver) is used.
+using the i2c_probe() routine. If a board defines
+CONFIG_SYS_POST_I2C_ADDRS the I2C test will pass if all devices
+listed in CONFIG_SYS_POST_I2C_ADDRS are found, and no additional
+devices are detected. If CONFIG_SYS_POST_I2C_ADDRS is not defined
+the test will pass if any I2C device is found.
2.2.2.2. Watchdog timer test
diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h
index 9702d63..c8e0ff2 100644
--- a/include/configs/KUP4K.h
+++ b/include/configs/KUP4K.h
@@ -139,9 +139,9 @@
/* List of I2C addresses to be verified by POST */
-#define I2C_ADDR_LIST {CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- }
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ }
#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h
index 9613ed9..ce731e3 100644
--- a/include/configs/KUP4X.h
+++ b/include/configs/KUP4X.h
@@ -149,9 +149,9 @@
/* List of I2C addresses to be verified by POST */
-#define I2C_ADDR_LIST {CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- }
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ }
#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h
index ad86e2e..f336e8d 100644
--- a/include/configs/TB5200.h
+++ b/include/configs/TB5200.h
@@ -251,10 +251,10 @@
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/* List of I2C addresses to be verified by POST */
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_SLAVE}
/*
* Flash configuration
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 2612c7a..794e11b 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -370,10 +370,10 @@
/* List of I2C addresses to be verified by POST */
#if defined (CONFIG_MINIFAP)
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_HWMON_ADDR, \
+ CONFIG_SYS_I2C_SLAVE}
#endif
/*
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 1b129a2..af6769b 100644
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -80,7 +80,9 @@
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
/* List of I2C addresses to be verified by POST */
-#define I2C_ADDR_LIST { CONFIG_SYS_I2C_SLAVE, CONFIG_SYS_I2C_IO, CONFIG_SYS_I2C_EEPROM }
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \
+ CONFIG_SYS_I2C_IO, \
+ CONFIG_SYS_I2C_EEPROM}
/* display image timestamps */
#define CONFIG_TIMESTAMP 1
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
index 1062765..9e48857 100644
--- a/include/configs/lwmon.h
+++ b/include/configs/lwmon.h
@@ -349,32 +349,32 @@
/* List of I2C addresses to be verified by POST */
#ifdef CONFIG_USE_FRAM
-#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
- CONFIG_SYS_I2C_SYSMON_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_POWER_A_ADDR, \
- CONFIG_SYS_I2C_POWER_B_ADDR, \
- CONFIG_SYS_I2C_KEYBD_ADDR, \
- CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR, \
- }
+#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+ CONFIG_SYS_I2C_SYSMON_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_POWER_A_ADDR, \
+ CONFIG_SYS_I2C_POWER_B_ADDR, \
+ CONFIG_SYS_I2C_KEYBD_ADDR, \
+ CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_ADDR, \
+ }
#else /* Use EEPROM - which show up on 8 consequtive addresses */
-#define I2C_ADDR_LIST { /* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
- CONFIG_SYS_I2C_SYSMON_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_POWER_A_ADDR, \
- CONFIG_SYS_I2C_POWER_B_ADDR, \
- CONFIG_SYS_I2C_KEYBD_ADDR, \
- CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR+0, \
- CONFIG_SYS_I2C_EEPROM_ADDR+1, \
- CONFIG_SYS_I2C_EEPROM_ADDR+2, \
- CONFIG_SYS_I2C_EEPROM_ADDR+3, \
- CONFIG_SYS_I2C_EEPROM_ADDR+4, \
- CONFIG_SYS_I2C_EEPROM_ADDR+5, \
- CONFIG_SYS_I2C_EEPROM_ADDR+6, \
- CONFIG_SYS_I2C_EEPROM_ADDR+7, \
- }
+#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
+ CONFIG_SYS_I2C_SYSMON_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_POWER_A_ADDR, \
+ CONFIG_SYS_I2C_POWER_B_ADDR, \
+ CONFIG_SYS_I2C_KEYBD_ADDR, \
+ CONFIG_SYS_I2C_PICIO_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+0, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+1, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+2, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+3, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+4, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+5, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+6, \
+ CONFIG_SYS_I2C_EEPROM_ADDR+7, \
+ }
#endif /* CONFIG_USE_FRAM */
/*-----------------------------------------------------------------------
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index a4e92cc..63e22d4 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -306,14 +306,13 @@
#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */
-#define I2C_ADDR_LIST { \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_EEPROM_CPU_ADDR, \
- CONFIG_SYS_I2C_EEPROM_MB_ADDR, \
- CONFIG_SYS_I2C_DSPIC_ADDR, \
- CONFIG_SYS_I2C_DSPIC_2_ADDR, \
- CONFIG_SYS_I2C_DSPIC_KEYB_ADDR, \
- CONFIG_SYS_I2C_DSPIC_IO_ADDR }
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_EEPROM_CPU_ADDR,\
+ CONFIG_SYS_I2C_EEPROM_MB_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_2_ADDR, \
+ CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,\
+ CONFIG_SYS_I2C_DSPIC_IO_ADDR }
/*
* Pass open firmware flat tree
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index b5ac168..880c8a3 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -271,10 +271,10 @@
/* List of I2C addresses to be verified by POST */
#if defined (CONFIG_MINIFAP)
-#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_HWMON_ADDR, \
- CONFIG_SYS_I2C_SLAVE }
+#undef CONFIG_SYS_POST_I2C_ADDRS
+#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_HWMON_ADDR, \
+ CONFIG_SYS_I2C_SLAVE}
#endif
/*
diff --git a/post/drivers/i2c.c b/post/drivers/i2c.c
index 3508177..e6f4c6a 100644
--- a/post/drivers/i2c.c
+++ b/post/drivers/i2c.c
@@ -26,10 +26,10 @@
*
* For verifying the I2C bus, a full I2C bus scanning is performed.
*
- * #ifdef I2C_ADDR_LIST
+ * #ifdef CONFIG_SYS_POST_I2C_ADDRS
* The test is considered as passed if all the devices and
* only the devices in the list are found.
- * #else [ ! I2C_ADDR_LIST ]
+ * #else [ ! CONFIG_SYS_POST_I2C_ADDRS ]
* The test is considered as passed if any I2C device is found.
* #endif
*/
@@ -43,7 +43,7 @@
int i2c_post_test (int flags)
{
unsigned int i;
-#ifndef I2C_ADDR_LIST
+#ifndef CONFIG_SYS_POST_I2C_ADDRS
/* Start at address 1, address 0 is the general call address */
for (i = 1; i < 128; i++)
if (i2c_probe (i) == 0)
@@ -54,7 +54,7 @@ int i2c_post_test (int flags)
#else
unsigned int ret = 0;
int j;
- const unsigned char i2c_addr_list[] = I2C_ADDR_LIST;
+ const unsigned char i2c_addr_list[] = CONFIG_SYS_POST_I2C_ADDRS;
/* Start at address 1, address 0 is the general call address */
for (i = 1; i < 128; i++) {
--
1.7.0.4
More information about the U-Boot
mailing list