[U-Boot] [PATCH v2 13/13] XPedite5500 board support
Peter Tyser
ptyser at xes-inc.com
Fri Oct 22 07:20:34 CEST 2010
From: John Schmoller <jschmoller at xes-inc.com>
Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.
Signed-off-by: John Schmoller <jschmoller at xes-inc.com>
Signed-off-by: Peter Tyser <ptyser at xes-inc.com>
CC: Kumar Gala <galak at kernel.crashing.org>
---
MAINTAINERS | 1 +
board/xes/common/Makefile | 2 +
board/xes/common/fsl_8xxx_clk.c | 11 +
board/xes/xpedite550x/Makefile | 39 +++
board/xes/xpedite550x/ddr.c | 165 ++++++++++
board/xes/xpedite550x/law.c | 54 +++
board/xes/xpedite550x/tlb.c | 98 ++++++
board/xes/xpedite550x/xpedite550x.c | 107 ++++++
boards.cfg | 1 +
include/configs/xpedite550x.h | 607 +++++++++++++++++++++++++++++++++++
10 files changed, 1085 insertions(+), 0 deletions(-)
create mode 100644 board/xes/xpedite550x/Makefile
create mode 100644 board/xes/xpedite550x/ddr.c
create mode 100644 board/xes/xpedite550x/law.c
create mode 100644 board/xes/xpedite550x/tlb.c
create mode 100644 board/xes/xpedite550x/xpedite550x.c
create mode 100644 include/configs/xpedite550x.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2da0561..b0da631 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -466,6 +466,7 @@ Peter Tyser <ptyser at xes-inc.com>
xpedite5170 MPC8640
xpedite5200 MPC8548
xpedite5370 MPC8572
+ xpedite5500 P2020
David Updegraff <dave at cray.com>
diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile
index bfade31..16e0b66 100644
--- a/board/xes/common/Makefile
+++ b/board/xes/common/Makefile
@@ -32,7 +32,9 @@ LIB = $(obj)lib$(VENDOR).a
COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_8xxx_pci.o
COBJS-$(CONFIG_MPC8572) += fsl_8xxx_clk.o
COBJS-$(CONFIG_MPC86xx) += fsl_8xxx_clk.o
+COBJS-$(CONFIG_P2020) += fsl_8xxx_clk.o
COBJS-$(CONFIG_FSL_DDR2) += fsl_8xxx_ddr.o
+COBJS-$(CONFIG_FSL_DDR3) += fsl_8xxx_ddr.o
COBJS-$(CONFIG_MPC85xx) += fsl_8xxx_misc.o board.o
COBJS-$(CONFIG_MPC86xx) += fsl_8xxx_misc.o board.o
COBJS-$(CONFIG_NAND_ACTL) += actl_nand.o
diff --git a/board/xes/common/fsl_8xxx_clk.c b/board/xes/common/fsl_8xxx_clk.c
index f4a17b7..20d0a30 100644
--- a/board/xes/common/fsl_8xxx_clk.c
+++ b/board/xes/common/fsl_8xxx_clk.c
@@ -38,7 +38,11 @@ unsigned long get_board_sys_clk(ulong dummy)
if (in_be32(&gur->gpporcr) & 0x10000)
return 66666666;
else
+#ifdef CONFIG_P2020
+ return 100000000;
+#else
return 50000000;
+#endif
}
#ifdef CONFIG_MPC85xx
@@ -54,6 +58,13 @@ unsigned long get_board_ddr_clk(ulong dummy)
if (ddr_ratio == 0x7)
return get_board_sys_clk(dummy);
+#ifdef CONFIG_P2020
+ if (in_be32(&gur->gpporcr) & 0x20000)
+ return 66666666;
+ else
+ return 100000000;
+#else
return 66666666;
+#endif
}
#endif
diff --git a/board/xes/xpedite550x/Makefile b/board/xes/xpedite550x/Makefile
new file mode 100644
index 0000000..8980a4b
--- /dev/null
+++ b/board/xes/xpedite550x/Makefile
@@ -0,0 +1,39 @@
+#
+# Copyright 2007-2008 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xes/xpedite550x/ddr.c b/board/xes/xpedite550x/ddr.c
new file mode 100644
index 0000000..718cd98
--- /dev/null
+++ b/board/xes/xpedite550x/ddr.c
@@ -0,0 +1,165 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
+ sizeof(ddr3_spd_eeprom_t));
+}
+
+void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ unsigned int i2c_address = 0;
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (ctrl_num == 0 && i == 0)
+ i2c_address = SPD_EEPROM_ADDRESS1;
+ get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ }
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+ return get_ddr_freq(0);
+}
+
+/*
+ * There are traditionally three board-specific SDRAM timing parameters
+ * which must be calculated based on the particular PCB artwork. These are:
+ * 1.) CPO (Read Capture Delay)
+ * - TIMING_CFG_2 register
+ * Source: Calculation based on board trace lengths and
+ * chip-specific internal delays.
+ * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
+ * - DDR_SDRAM_CLK_CNTL register
+ * Source: Signal Integrity Simulations
+ * 3.) 2T Timing on Addr/Ctl
+ * - TIMING_CFG_2 register
+ * Source: Signal Integrity Simulations
+ * Usually only needed with heavy load/very high speed (>DDR2-800)
+ *
+ * ====== XPedite550x DDR3-800 read delay calculations ======
+ *
+ * The P2020 processor provides an autoleveling option. Setting CPO to
+ * 0x1f enables this auto configuration.
+ */
+
+typedef struct {
+ unsigned short datarate_mhz_low;
+ unsigned short datarate_mhz_high;
+ unsigned char clk_adjust;
+ unsigned char cpo;
+} board_specific_parameters_t;
+
+const board_specific_parameters_t board_specific_parameters[][20] = {
+ {
+ /* Controller 0 */
+ {
+ /* DDR3-600/667 */
+ .datarate_mhz_low = 500,
+ .datarate_mhz_high = 750,
+ .clk_adjust = 5,
+ .cpo = 31,
+ },
+ {
+ /* DDR3-800 */
+ .datarate_mhz_low = 750,
+ .datarate_mhz_high = 850,
+ .clk_adjust = 5,
+ .cpo = 31,
+ },
+ },
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const board_specific_parameters_t *pbsp =
+ &(board_specific_parameters[ctrl_num][0]);
+ u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+ sizeof(board_specific_parameters[0][0]);
+ u32 i;
+ ulong ddr_freq;
+
+ /*
+ * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+ * there are two dimms in the controller, set odt_rd_cfg to 3 and
+ * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+ */
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i&1) { /* odd CS */
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 0;
+ } else { /* even CS */
+ if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 4;
+ } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+ popts->cs_local_opts[i].odt_rd_cfg = 3;
+ popts->cs_local_opts[i].odt_wr_cfg = 3;
+ }
+ }
+ }
+
+ /*
+ * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->twoT_en = 0;
+ }
+ pbsp++;
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+
+ /*
+ * Enable on-die termination.
+ * From the Micron Technical Node TN-41-04, RTT_Nom should typically
+ * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR
+ * is handled in the Freescale DDR3 driver. Set RTT_Nom here.
+ */
+ popts->rtt_override = 1;
+ popts->rtt_override_value = 3;
+}
+
diff --git a/board/xes/xpedite550x/law.c b/board/xes/xpedite550x/law.c
new file mode 100644
index 0000000..4d4445d
--- /dev/null
+++ b/board/xes/xpedite550x/law.c
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/*
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_PCIE1_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1),
+ SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1),
+#endif
+#ifdef CONFIG_SYS_PCIE2_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2),
+ SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2),
+#endif
+#ifdef CONFIG_SYS_PCIE3_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3),
+ SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/xes/xpedite550x/tlb.c b/board/xes/xpedite550x/tlb.c
new file mode 100644
index 0000000..cf3ff4d
--- /dev/null
+++ b/board/xes/xpedite550x/tlb.c
@@ -0,0 +1,98 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* W**G* - NOR flashes */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ /* *I*G* - NAND flash */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_1M, 1),
+
+ /* **M** - Boot page for secondary processors */
+ SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+ 0, 3, BOOKE_PAGESZ_4K, 1),
+
+#ifdef CONFIG_PCIE1
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_1G, 1),
+#endif
+
+#ifdef CONFIG_PCIE2
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#ifdef CONFIG_PCIE3
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_64M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/xes/xpedite550x/xpedite550x.c b/board/xes/xpedite550x/xpedite550x.c
new file mode 100644
index 0000000..2ad30a3
--- /dev/null
+++ b/board/xes/xpedite550x/xpedite550x.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <pca953x.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void ft_board_pci_setup(void *blob, bd_t *bd);
+
+static void flash_cs_fixup(void)
+{
+ int flash_sel;
+
+ /*
+ * Print boot dev and swap flash flash chip selects if booted from 2nd
+ * flash. Swapping chip selects presents user with a common memory
+ * map regardless of which flash was booted from.
+ */
+ flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
+ CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
+ printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
+
+ if (flash_sel) {
+ set_lbc_br(0, CONFIG_SYS_BR1_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_OR1_PRELIM);
+
+ set_lbc_br(1, CONFIG_SYS_BR0_PRELIM);
+ set_lbc_or(1, CONFIG_SYS_OR0_PRELIM);
+ }
+}
+
+int board_early_init_r(void)
+{
+ /* Initialize PCA9557 devices */
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0);
+
+ /*
+ * Remap NOR flash region to caching-inhibited
+ * so that flash can be erased/programmed properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* Invalidate existing TLB entry for NOR flash */
+ disable_tlb(0);
+ set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+ (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256M, 1);
+
+ flash_cs_fixup();
+
+ return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_PCI
+ ft_board_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+}
+#endif
+
+#ifdef CONFIG_MP
+extern void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+void board_lmb_reserve(struct lmb *lmb)
+{
+ cpu_mp_lmb_reserve(lmb);
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index a524272..e8afdb1 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -558,6 +558,7 @@ MPC8560ADS powerpc mpc85xx mpc8560ads freescale
MPC8568MDS powerpc mpc85xx mpc8568mds freescale
xpedite520x powerpc mpc85xx - xes
xpedite537x powerpc mpc85xx - xes
+xpedite550x powerpc mpc85xx - xes
sbc8540_33 powerpc mpc85xx sbc8560 - - SBC8540
sbc8540_66 powerpc mpc85xx sbc8560 - - SBC8540
sbc8548_PCI_33 powerpc mpc85xx sbc8548 - - sbc8548:PCI,33
diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
new file mode 100644
index 0000000..a849cf9
--- /dev/null
+++ b/include/configs/xpedite550x.h
@@ -0,0 +1,607 @@
+/*
+ * Copyright 2010 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * xpedite550x board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
+#define CONFIG_P2020 1
+#define CONFIG_XPEDITE550X 1
+#define CONFIG_SYS_BOARD_NAME "XPedite5500"
+#define CONFIG_SYS_FORM_PMC_XMC 1
+#define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */
+#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#endif
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+#define CONFIG_FSL_ELBC 1
+
+/*
+ * Multicore config
+ */
+#define CONFIG_MP
+#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
+#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
+
+/*
+ * DDR config
+ */
+#define CONFIG_FSL_DDR3
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS1 0x54
+#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x20000000
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_I2C)
+#define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_LM75_ADDR, \
+ CONFIG_SYS_I2C_LM90_ADDR, \
+ CONFIG_SYS_I2C_PCA953X_ADDR0, \
+ CONFIG_SYS_I2C_PCA953X_ADDR2, \
+ CONFIG_SYS_I2C_PCA953X_ADDR3, \
+ CONFIG_SYS_I2C_RTC_ADDR}
+
+/*
+ * Memory map
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
+ * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
+ * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
+ * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable
+ * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
+ * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
+ * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
+ * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE 0xef800000
+#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \
+ CONFIG_SYS_NAND_BASE2}
+#define CONFIG_SYS_MAX_NAND_DEVICE 2
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */
+#define CONFIG_NAND_FSL_ELBC
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xf8000000
+#define CONFIG_SYS_FLASH_BASE2 0xf0000000
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
+ {0xf7f40000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
+ OR_GPCM_CSNT | \
+ OR_GPCM_XACS | \
+ OR_GPCM_ACS_DIV2 | \
+ OR_GPCM_SCY_8 | \
+ OR_GPCM_TRLX | \
+ OR_GPCM_EHTR | \
+ OR_GPCM_EAD)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
+ OR_FCM_PGS | \
+ OR_FCM_CSCT | \
+ OR_FCM_CST | \
+ OR_FCM_CHT | \
+ OR_FCM_SCY_1 | \
+ OR_FCM_TRLX | \
+ OR_FCM_EHTR)
+
+/* NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
+#define CONFIG_SYS_INIT_RAM_END 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+#define CONFIG_FDT_FIXUP_PCI_IRQ 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_I2C_MULTI_BUS
+
+/* I2C DS7505 temperature sensor */
+#define CONFIG_DTT_LM75
+#define CONFIG_DTT_SENSORS { 0 }
+#define CONFIG_SYS_I2C_LM75_ADDR 0x48
+
+/* I2C ADT7461 temperature sensor */
+#define CONFIG_SYS_I2C_LM90_ADDR 0x4C
+
+/* I2C EEPROM - AT24C128B */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
+#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
+#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
+#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/*
+ * GPIO pin definitions, PU = pulled high, PD = pulled low
+ */
+/* PCA9557 @ 0x18*/
+#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
+#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
+#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */
+
+/* PCA9557 @ 0x1e*/
+#define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */
+#define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */
+#define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */
+
+/* PCA9557 @ 0x1f */
+#define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */
+#define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1 - PEX8112 or XMC, depending on build option */
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
+
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_TSEC_TBI
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_ETHPRIME "eTSEC2"
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHY_ADDR 2
+#define TSEC2_PHYIDX 0
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_PHY_ADDR 3
+#define TSEC3_PHYIDX 0
+#define CONFIG_HAS_ETH2
+
+/*
+ * USB
+ */
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE 0x8000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff Pri U-Boot (512 KB)
+ * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff Pri FDT (256KB)
+ * fef00000 - ffefffff Pri OS image (16MB)
+ * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
+ *
+ * f7f80000 - f7ffffff Sec U-Boot (512 KB)
+ * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
+ * f7f00000 - f7f3ffff Sec FDT (256KB)
+ * f6f00000 - f7efffff Sec OS image (16MB)
+ * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000)
+
+#define CONFIG_PROG_UBOOT1 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_UBOOT2 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_BOOT_OS_NET \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "if test -n $fdtaddr; then " \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "bootm $osaddr - $fdtaddr; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi; " \
+ "else; " \
+ "bootm $osaddr; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS1 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS2 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT1 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT2 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=yes\0" \
+ "download_cmd=tftp\0" \
+ "console_args=console=ttyS0,115200\0" \
+ "root_args=root=/dev/nfs rw\0" \
+ "misc_args=ip=on\0" \
+ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+ "bootfile=/home/user/file\0" \
+ "osfile=/home/user/board.uImage\0" \
+ "fdtfile=/home/user/board.dtb\0" \
+ "ubootfile=/home/user/u-boot.bin\0" \
+ "fdtaddr=c00000\0" \
+ "osaddr=0x1000000\0" \
+ "loadaddr=0x1000000\0" \
+ "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
+ "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
+ "prog_os1="CONFIG_PROG_OS1"\0" \
+ "prog_os2="CONFIG_PROG_OS2"\0" \
+ "prog_fdt1="CONFIG_PROG_FDT1"\0" \
+ "prog_fdt2="CONFIG_PROG_FDT2"\0" \
+ "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
+ "bootcmd_flash1=run set_bootargs; " \
+ "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+ "bootcmd_flash2=run set_bootargs; " \
+ "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+ "bootcmd=run bootcmd_flash1\0"
+#endif /* __CONFIG_H */
--
1.7.0.4
More information about the U-Boot
mailing list