[U-Boot] [PATCH V3] mvsata_ide: adjust port init sequence

Albert ARIBAUD albert.aribaud at free.fr
Sat Sep 25 07:30:12 CEST 2010


Le 16/09/2010 13:13, Prafulla Wadaskar a écrit :
>
>
>> -----Original Message-----
>> From: u-boot-bounces at lists.denx.de
>> [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Albert Aribaud
>> Sent: Wednesday, September 08, 2010 11:01 PM
>> To: u-boot at lists.denx.de
>> Subject: [U-Boot] [PATCH V3] mvsata_ide: adjust port init sequence
>>
>> mvsata_ide_initialize_port(): adjust init sequence (SStatus
>> should be checked only after all writes to SControl) and
>> return success/failure to ide_preinit().
>>
>> Also, as some tests showed init durations in the hundreds
>> of us, raise the time-out to 01 ms to be on the safe side.
>>
>> Signed-off-by: Albert Aribaud<albert.aribaud at free.fr>
>> ---
>> PATCH HISTORY
>>
>> V1	Initial patch.
>> V2	Fixed wrong placement of comment.
>> 	Fixed wrong description (was 01 ms, should have been 10).
>> 	Added Signed-off-by.
>> V3	Replaced return status values with symbolic names.
>> 	Made error status values negative.
>> 	Renamed 'tout' to 'timeleft' for clarity.
>> 	Replaced ternary '?:' operator with '!' and if.
>>
>> Patch was run through checkscript.pl with 0 errors and warnings.
>>
>>   drivers/block/mvsata_ide.c |   42
>> +++++++++++++++++++++++++++++++++---------
>>   1 files changed, 33 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c
>> index 077b278..3d6993a 100644
>> --- a/drivers/block/mvsata_ide.c
>> +++ b/drivers/block/mvsata_ide.c
>> @@ -91,29 +91,48 @@ struct mvsata_port_registers {
>>   #define MVSATA_SSTATUS_DET_DEVCOMM		0x00000003
>>
>>   /*
>> + * Status codes to return to client callers. Currently,
>> callers ignore
>> + * exact value and only care for zero or nonzero, so no need
>> to make this
>> + * public, it is only #define'd for clarity.
>> + * If/when standard negative codes are implemented in
>> U-boot, then these
>> + * #defines should be moved to, or replaced by ones from,
>> the common list
>> + * of status codes.
>> + */
>> +
>> +#define MVSATA_STATUS_OK	0
>> +#define MVSATA_STATUS_TIMEOUT	-1
>> +
>> +/*
>>    * Initialize one MVSATAHC port: set SControl's IPM to
>> "always active"
>>    * and DET to "reset", then wait for SStatus's DET to become
>> "device and
>>    * comm ok" (or time out after 50 us if no device), then set
>> SControl's
>>    * DET back to "no action".
>>    */
>>
>> -static void mvsata_ide_initialize_port(struct
>> mvsata_port_registers *port)
>> +static int mvsata_ide_initialize_port(struct
>> mvsata_port_registers *port)
>>   {
>>   	u32 control;
>>   	u32 status;
>> -	u32 tout = 50; /* wait at most 50 us for SATA reset to
>> complete */
>> +	u32 timeleft = 10000; /* wait at most 10 ms for SATA
>> reset to complete */
>>
>> +	/* Set control IPM to 3 (no low power) and DET to 1
>> (initialize) */
>>   	control = readl(&port->scontrol);
>>   	control = (control&  ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_INIT;
>>   	writel(control,&port->scontrol);
>> -	while (--tout) {
>> +	/* Toggle control DET back to 0 (normal operation) */
>> +	control = (control&  ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
>> +	writel(control,&port->scontrol);
>> +	/* wait for status DET to become 3 (device and
>> communication OK) */
>> +	while (--timeleft) {
>>   		status = readl(&port->sstatus)&
>> MVSATA_SSTATUS_DET_MASK;
>>   		if (status == MVSATA_SSTATUS_DET_DEVCOMM)
>>   			break;
>>   		udelay(1);
>>   	}
>> -	control = (control&  ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE;
>> -	writel(control,&port->scontrol);
>> +	/* return success or time-out error depending on time left */
>> +	if (!timeleft)
>> +		return MVSATA_STATUS_TIMEOUT;
>> +	return MVSATA_STATUS_OK;
>>   }
>>
>>   /*
>> @@ -123,18 +142,23 @@ static void
>> mvsata_ide_initialize_port(struct mvsata_port_registers *port)
>>
>>   int ide_preinit(void)
>>   {
>> +	int status;
>>   	/* Enable ATA port 0 (could be SATA port 0 or 1) if declared */
>>   #if defined(CONFIG_SYS_ATA_IDE0_OFFSET)
>> -	mvsata_ide_initialize_port(
>> +	status = mvsata_ide_initialize_port(
>>   		(struct mvsata_port_registers *)
>>   		(CONFIG_SYS_ATA_BASE_ADDR +
>> CONFIG_SYS_ATA_IDE0_OFFSET));
>> +	if (status)
>> +		return status;
>>   #endif
>>   	/* Enable ATA port 1 (could be SATA port 0 or 1) if declared */
>>   #if defined(CONFIG_SYS_ATA_IDE1_OFFSET)
>> -	mvsata_ide_initialize_port(
>> +	status = mvsata_ide_initialize_port(
>>   		(struct mvsata_port_registers *)
>>   		(CONFIG_SYS_ATA_BASE_ADDR +
>> CONFIG_SYS_ATA_IDE1_OFFSET));
>> +	if (status)
>> +		return status;
>>   #endif
>> -	/* return 0 as we always succeed */
>> -	return 0;
>> +	/* return success if all ports initializations succeeded */
>> +	return MVSATA_STATUS_OK;
>>   }
>
> Applied to u-boot-marvell.git master branch
>
> Regards..
> Prafulla . .

Prafulla,

Is it possible to ask for a pull of the marvell tree in order to get 
this bugfix pulled in v2010.09?

Amicalement,
-- 
Albert.


More information about the U-Boot mailing list