[U-Boot] [PATCH] Fix CFI flash driver for 8-bit bus support
Aaron Williams
aaron.williams at caviumnetworks.com
Sat Apr 2 09:17:01 CEST 2011
This patch corrects the addresses used when working with Spansion/AMD FLASH chips.
Addressing for 8 and 16 bits is almost identical except in the 16-bit case the
LSB of the address is always 0. The confusion arose because the addresses
in the datasheet for 16-bit mode are word addresses but this code assumed it was
byte addresses.
I have only been able to test this on our Octeon boards which use either an 8-bit
or 16-bit bus. I have not tested the case where there's an 8-bit part on a 16-bit
bus.
This patch also adds some delays as suggested by Spansion.
If a part can be both 8 and 16-bits, it forces it to work in 8-bit mode if an
8-bit bus is detected.
-Aaron Williams
Signed-off-by: Aaron Williams <aaron.williams at caviumnetworks.com>
---
drivers/mtd/cfi_flash.c | 93 ++++++++++++++++++++++++++++++++++-------------
include/mtd/cfi_flash.h | 40 ++++++++++----------
2 files changed, 87 insertions(+), 46 deletions(-)
diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c
index 0909fe7..eab1fbe 100644
--- a/drivers/mtd/cfi_flash.c
+++ b/drivers/mtd/cfi_flash.c
@@ -10,6 +10,9 @@
*
* Copyright (C) 2006
* Tolunay Orkun <listmember at orkun.us>
+ *
+ * Copyright (C) 2011 Cavium Networks, Inc.
+ * Aaron Williams <Aaron.Williams at caviumnetworks.com>
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -32,7 +35,6 @@
*/
/* The DEBUG define must be before common to enable debugging */
-/* #define DEBUG */
#include <common.h>
#include <asm/processor.h>
@@ -209,9 +211,11 @@ unsigned long flash_sector_size(flash_info_t *info, flash_sect_t sect)
static inline void *
flash_map (flash_info_t * info, flash_sect_t sect, uint offset)
{
- unsigned int byte_offset = offset * info->portwidth;
-
- return (void *)(info->start[sect] + byte_offset);
+ unsigned int byte_offset = offset * info->portwidth / info->chipwidth;
+ unsigned int addr = (info->start[sect] + byte_offset);
+ unsigned int mask = 0xffffffff << (info->portwidth - 1);
+
+ return (void *)(addr & mask);
}
static inline void flash_unmap(flash_info_t *info, flash_sect_t sect,
@@ -397,6 +401,8 @@ void flash_write_cmd (flash_info_t * info, flash_sect_t sect,
#endif
flash_write64(cword.ll, addr);
break;
+ default:
+ debug ("fwc: Unknown port width %d\n", info->portwidth);
}
/* Ensure all the instructions are fully finished */
@@ -581,6 +587,7 @@ static int flash_status_check (flash_info_t * info, flash_sect_t sector,
prompt, info->start[sector],
flash_read_long (info, sector, 0));
flash_write_cmd (info, sector, 0, info->cmd_reset);
+ udelay(1);
return ERR_TIMOUT;
}
udelay (1); /* also triggers watchdog */
@@ -628,6 +635,7 @@ static int flash_full_status_check (flash_info_t * info, flash_sect_t sector,
puts ("Vpp Low Error.\n");
}
flash_write_cmd (info, sector, 0, info->cmd_reset);
+ udelay(1);
break;
default:
break;
@@ -744,12 +752,8 @@ static void flash_add_byte (flash_info_t * info, cfiword_t * cword, uchar c)
static flash_sect_t find_sector (flash_info_t * info, ulong addr)
{
static flash_sect_t saved_sector = 0; /* previously found sector */
- static flash_info_t *saved_info = 0; /* previously used flash bank */
flash_sect_t sector = saved_sector;
- if ((info != saved_info) || (sector >= info->sector_count))
- sector = 0;
-
while ((info->start[sector] < addr)
&& (sector < info->sector_count - 1))
sector++;
@@ -761,7 +765,6 @@ static flash_sect_t find_sector (flash_info_t * info, ulong addr)
sector--;
saved_sector = sector;
- saved_info = info;
return sector;
}
@@ -825,12 +828,15 @@ static int flash_write_cfiword (flash_info_t * info, ulong dest,
switch (info->portwidth) {
case FLASH_CFI_8BIT:
+ debug("%s: 8-bit 0x%02x\n", __func__, cword.c);
flash_write8(cword.c, dstaddr);
break;
case FLASH_CFI_16BIT:
+ debug("%s: 16-bit 0x%04x\n", __func__, cword.w);
flash_write16(cword.w, dstaddr);
break;
case FLASH_CFI_32BIT:
+ debug("%s: 32-bit 0x%08lx\n", __func__, cword.l);
flash_write32(cword.l, dstaddr);
break;
case FLASH_CFI_64BIT:
@@ -1043,6 +1049,8 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
int prot;
flash_sect_t sect;
int st;
+
+ debug("%s: erasing sectors %d to %d\n", __func__, s_first, s_last);
if (info->flash_id != FLASH_MAN_CFI) {
puts ("Can't erase unknown flash type - aborted\n");
@@ -1082,6 +1090,7 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
+ flash_write_cmd (info, 0, 0, AMD_CMD_RESET);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect,
info->addr_unlock1,
@@ -1121,6 +1130,8 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
rcode = 1;
else if (flash_verbose)
putc ('.');
+ } else {
+ debug("\nSector %d is protected.\n", sect);
}
}
@@ -1490,6 +1501,7 @@ void flash_read_user_serial (flash_info_t * info, void *buffer, int offset,
flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID);
memcpy (dst, src + offset, len);
flash_write_cmd (info, 0, 0, info->cmd_reset);
+ udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_USER_PROTECTION, src);
}
@@ -1505,6 +1517,7 @@ void flash_read_factory_serial (flash_info_t * info, void *buffer, int offset,
flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID);
memcpy (buffer, src + offset, len);
flash_write_cmd (info, 0, 0, info->cmd_reset);
+ udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_INTEL_PROTECTION, src);
}
@@ -1536,6 +1549,7 @@ static void cfi_reverse_geometry(struct cfi_qry *qry)
static void cmdset_intel_read_jedec_ids(flash_info_t *info)
{
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
+ udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
info->manufacturer_id = flash_read_uchar (info,
@@ -1573,8 +1587,7 @@ static void cmdset_amd_read_jedec_ids(flash_info_t *info)
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
-
- manuId = flash_read_uchar (info, FLASH_OFFSET_MANUFACTURER_ID);
+ manuId = flash_read_uchar(info, FLASH_OFFSET_MANUFACTURER_ID);
/* JEDEC JEP106Z specifies ID codes up to bank 7 */
while (manuId == FLASH_CONTINUATION_CODE && bankId < 0x800) {
bankId += 0x100;
@@ -1604,6 +1617,7 @@ static void cmdset_amd_read_jedec_ids(flash_info_t *info)
break;
}
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
+ udelay(1);
}
static int cmdset_amd_init(flash_info_t *info, struct cfi_qry *qry)
@@ -1719,7 +1733,7 @@ static void flash_read_cfi (flash_info_t *info, void *buf,
unsigned int i;
for (i = 0; i < len; i++)
- p[i] = flash_read_uchar(info, start + i);
+ p[i] = flash_read_uchar(info, start + (i * 2));
}
void __flash_cmd_reset(flash_info_t *info)
@@ -1730,6 +1744,7 @@ void __flash_cmd_reset(flash_info_t *info)
* that AMD flash roms ignore the Intel command.
*/
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
+ udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
}
void flash_cmd_reset(flash_info_t *info)
@@ -1739,21 +1754,38 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
{
int cfi_offset;
- /* Issue FLASH reset command */
- flash_cmd_reset(info);
-
for (cfi_offset=0;
cfi_offset < sizeof(flash_offset_cfi) / sizeof(uint);
cfi_offset++) {
+ /* Issue FLASH reset command */
+ flash_cmd_reset(info);
flash_write_cmd (info, 0, flash_offset_cfi[cfi_offset],
FLASH_CMD_CFI);
if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
- && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R')
- && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
+ && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'R')
+ && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 4, 'Y')) {
flash_read_cfi(info, qry, FLASH_OFFSET_CFI_RESP,
sizeof(struct cfi_qry));
+#ifdef CONFIG_SYS_FLASH_INTERFACE_WIDTH
+ info->interface = CONFIG_SYS_FLASH_INTERFACE_WIDTH;
+#else
info->interface = le16_to_cpu(qry->interface_desc);
-
+ /* Some flash chips can support multiple bus widths.
+ * In this case, override the interface width and
+ * limit it to the port width.
+ */
+ if ((info->interface == FLASH_CFI_X8X16) &&
+ (info->portwidth == FLASH_CFI_8BIT)) {
+ debug("Overriding 16-bit interface width to "
+ " 8-bit port width.\n");
+ info->interface = FLASH_CFI_X8;
+ } else if ((info->interface == FLASH_CFI_X16X32) &&
+ (info->portwidth == FLASH_CFI_16BIT)) {
+ debug("Overriding 16-bit interface width to "
+ " 16-bit port width.\n");
+ info->interface = FLASH_CFI_X16;
+ }
+#endif
info->cfi_offset = flash_offset_cfi[cfi_offset];
debug ("device interface is %d\n",
info->interface);
@@ -1764,8 +1796,8 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
/* calculate command offsets as in the Linux driver */
- info->addr_unlock1 = 0x555;
- info->addr_unlock2 = 0x2aa;
+ info->addr_unlock1 = 0xaaa;
+ info->addr_unlock2 = 0x555;
/*
* modify the unlock address if we are
@@ -1799,8 +1831,11 @@ static int flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
for (info->chipwidth = FLASH_CFI_BY8;
info->chipwidth <= info->portwidth;
info->chipwidth <<= 1)
- if (__flash_detect_cfi(info, qry))
+ if (__flash_detect_cfi(info, qry)) {
+ debug("Found CFI flash, portwidth %d, chipwidth %d\n",
+ info->portwidth, info->chipwidth);
return 1;
+ }
}
debug ("not found\n");
return 0;
@@ -1819,7 +1854,7 @@ static void flash_fixup_amd(flash_info_t *info, struct cfi_qry *qry)
/* CFI < 1.1, try to guess from device id */
if ((info->device_id & 0x80) != 0)
cfi_reverse_geometry(qry);
- } else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
+ } else if (flash_read_uchar(info, info->ext_addr + 0x1e) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
@@ -1891,14 +1926,15 @@ ulong flash_get_size (phys_addr_t base, int banknum)
if (flash_detect_cfi (info, &qry)) {
info->vendor = le16_to_cpu(qry.p_id);
- info->ext_addr = le16_to_cpu(qry.p_adr);
+ info->ext_addr = le16_to_cpu(qry.p_adr) * 2;
+ debug("extended address is 0x%x\n", info->ext_addr);
num_erase_regions = qry.num_erase_regions;
if (info->ext_addr) {
info->cfi_version = (ushort) flash_read_uchar (info,
- info->ext_addr + 3) << 8;
+ info->ext_addr + 6) << 8;
info->cfi_version |= (ushort) flash_read_uchar (info,
- info->ext_addr + 4);
+ info->ext_addr + 8);
}
#ifdef DEBUG
@@ -1945,13 +1981,16 @@ ulong flash_get_size (phys_addr_t base, int banknum)
debug ("device id is 0x%x\n", info->device_id);
debug ("device id2 is 0x%x\n", info->device_id2);
debug ("cfi version is 0x%04x\n", info->cfi_version);
-
+ debug ("port width: %d, chipwidth: %d, interface: %d\n",
+ info->portwidth, info->chipwidth, info->interface);
size_ratio = info->portwidth / info->chipwidth;
+#if 0
/* if the chip is x8/x16 reduce the ratio by half */
if ((info->interface == FLASH_CFI_X8X16)
&& (info->chipwidth == FLASH_CFI_BY8)) {
size_ratio >>= 1;
}
+#endif
debug ("size_ratio %d port %d bits chip %d bits\n",
size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
@@ -2023,6 +2062,8 @@ ulong flash_get_size (phys_addr_t base, int banknum)
sect_cnt++;
}
}
+ debug ("port width: %d, chipwidth: %d, interface: %d\n",
+ info->portwidth, info->chipwidth, info->interface);
info->sector_count = sect_cnt;
info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size);
diff --git a/include/mtd/cfi_flash.h b/include/mtd/cfi_flash.h
index 3245b44..edcf9be 100644
--- a/include/mtd/cfi_flash.h
+++ b/include/mtd/cfi_flash.h
@@ -71,29 +71,29 @@
#define FLASH_CONTINUATION_CODE 0x7F
#define FLASH_OFFSET_MANUFACTURER_ID 0x00
-#define FLASH_OFFSET_DEVICE_ID 0x01
-#define FLASH_OFFSET_DEVICE_ID2 0x0E
-#define FLASH_OFFSET_DEVICE_ID3 0x0F
-#define FLASH_OFFSET_CFI 0x55
+#define FLASH_OFFSET_DEVICE_ID 0x02
+#define FLASH_OFFSET_DEVICE_ID2 0x1C
+#define FLASH_OFFSET_DEVICE_ID3 0x1E
+#define FLASH_OFFSET_CFI 0xAA
#define FLASH_OFFSET_CFI_ALT 0x555
-#define FLASH_OFFSET_CFI_RESP 0x10
-#define FLASH_OFFSET_PRIMARY_VENDOR 0x13
+#define FLASH_OFFSET_CFI_RESP 0x20
+#define FLASH_OFFSET_PRIMARY_VENDOR 0x26
/* extended query table primary address */
-#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x15
+#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x2A
#define FLASH_OFFSET_WTOUT 0x1F
-#define FLASH_OFFSET_WBTOUT 0x20
-#define FLASH_OFFSET_ETOUT 0x21
-#define FLASH_OFFSET_CETOUT 0x22
-#define FLASH_OFFSET_WMAX_TOUT 0x23
-#define FLASH_OFFSET_WBMAX_TOUT 0x24
-#define FLASH_OFFSET_EMAX_TOUT 0x25
-#define FLASH_OFFSET_CEMAX_TOUT 0x26
-#define FLASH_OFFSET_SIZE 0x27
-#define FLASH_OFFSET_INTERFACE 0x28
-#define FLASH_OFFSET_BUFFER_SIZE 0x2A
-#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C
-#define FLASH_OFFSET_ERASE_REGIONS 0x2D
-#define FLASH_OFFSET_PROTECT 0x02
+#define FLASH_OFFSET_WBTOUT 0x40
+#define FLASH_OFFSET_ETOUT 0x4A
+#define FLASH_OFFSET_CETOUT 0x44
+#define FLASH_OFFSET_WMAX_TOUT 0x46
+#define FLASH_OFFSET_WBMAX_TOUT 0x48
+#define FLASH_OFFSET_EMAX_TOUT 0x4A
+#define FLASH_OFFSET_CEMAX_TOUT 0x4C
+#define FLASH_OFFSET_SIZE 0x4E
+#define FLASH_OFFSET_INTERFACE 0x50
+#define FLASH_OFFSET_BUFFER_SIZE 0x54
+#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x58
+#define FLASH_OFFSET_ERASE_REGIONS 0x5A
+#define FLASH_OFFSET_PROTECT 0x04
#define FLASH_OFFSET_USER_PROTECTION 0x85
#define FLASH_OFFSET_INTEL_PROTECTION 0x81
--
1.7.3.4
More information about the U-Boot
mailing list